Determination of interfacial heat transfer coefficient and its application in high pressure die casting process

In this paper,the research progress of the interfacial heat transfer in high pressure die casting(HPDC)is reviewed.Results including determination of the interfacial heat transfer coefficient(IHTC),influence of casting thickness,process parameters and casting alloys on the IHTC are summarized and discussed.A thermal boundary condition model was developed based on the two correlations:(a)IHTC and casting solid fraction and(b)IHTC peak value and initial die surface temperature.The boundary model was then applied during the determination of the temperature field in HPDC and excellent agreement was found.

Study on interfacial heat transfer coefficient at metal/die interface during high pressure die casting process of AZ91D alloy

The high pressure die casting (HPDC) process is one of the fastest growing and most efficient methods for the production of complex shape castings of magnesium and aluminum alloys in today's manufacturing industry. In this study, a high pressure die casting experiment using AZ91D magnesium alloy was conducted, and the temperature profiles inside the die were measured. By using a computer program based on solving the inverse heat problem, the metal/die interfacial heat transfer coefficient (IHTC) was calculated and studied. The results show that the IHTC between the metal and die increases right after the liquid metal is brought into the cavity by the plunger, and decreases as the solidification process of the liquid metal proceeds until the liquid metal is completely solidified, when the IHTC tends to be stable. The interfacial heat transfer coefficient shows different characteristics under different casting wall thicknesses and varies with the change of solidification behavior.

Measurement of temperature inside die and estimation of interfacial heat transfer coefficient in squeeze casting

As an advanced near-net shape technology, squeeze casting is an excellent method for producing high integrity castings. Numerical simulation is a very effective method to optimize squeeze casting process, and the interfacial heat transfer coefficient(IHTC) is an important boundary condition in numerical simulation. Therefore, the study of the IHTC is of great significance. In the present study, experiments were conducted and a "plate shape" aluminum alloy casting was cast in H13 steel die. In order to obtain accurate temperature readings inside the die, a special temperature sensor units(TSU) was designed. Six 1 mm wide and 1 mm deep grooves were machined in the sensor unit for the placement of the thermocouples whose tips were welded to the end wall. Each groove was machined to terminate at a particular distance(1, 3, and 6 mm) from the front end of the sensor unit. Based on the temperature measurements inside the die, the interfacial heat transfer coefficient(IHTC) at the metal-die interface was determined by applying an inverse approach. The acquired data were processed by a low pass filtering method based on Fast Fourier Transform(FFT). The feature of the IHTC at the metal-die interface was discussed.

Optimal Experiment Design for the Identification of the Interfacial Heat Transfer Coefficient in Sand Casting

The interfacial heat transfer coefficient(IHTC)is one of the main input parameters required by casting simulation software.It plays an important role in the accurate modeling of the solidification process.However,its value is not easily identifiable by means of experimental methods requiring temperature measurements during the solidification process itself.For these reasons,an optimal experiment design was performed in this study to determine the optimal position for the temperature measurement and the optimal thickness of the rectangular cast iron part.This parameter was identified using an inverse technique.In particular,two different algorithms were used:Levenberg Marquard(LM)and Monte Carlo(MC).A numerical model of the solidification process was associated with the optimization algorithm.The temperature was measured at different positions from the mould/metal interface at d=0 mm(mould/metal interface),30 mm,60 mm and 90 mm.the thicknesses of the cast part were:L1=40 mm,60 mm and 80 mm.A comparative study on the IHTC identification was then carried out by varying the initial value of the IHTC between 500 Wm^(-2)K^(-1) and 1050 Wm^(-2)K^(-1).Results showed that the MC algorithm used for estimating the IHTC gives the best results,and the optimal position was at d=30 mm,the position closest to the mould/metal interface,for the lowest thickness L1=40 mm.

Spatial interfacial heat transfer and surface characteristics during gravity casting of A356 alloy

As one of the key boundary conditions during casting solidification process, the interfacial heat transfer coefficient (IHTC) affects the temperature variation and distribution. Based on the improved nonlinear estimation method (NEM), thermal measurements near both bottom and lateral metal-mold interfaces throughout A356 gravity casting process were carried out and applied to solving the inverse heat conduction problem (IHCP). Finite element method (FEM) is employed for modeling transient thermal fields implementing a developed NEM interface program to quantify transient IHTCs. It is found that IHTCs at the lateral interface become stable after the volumetric shrinkage of casting while those of the bottom interface reach the steady period once a surface layer has solidified. The stable value of bottom IHTCs is 750 W/(m^2·℃), which is approximately 3 times that at the lateral interface. Further analysis of the interplay between spatial IHTCs and observed surface morphology reveals that spatial heat transfer across casting-mold interfaces is the direct result of different interface evolution during solidification process.

Heat Transfer between Casting and Die during High Pressure Die Casting Process of AM50 Alloy-Modeling and Experimental Results

A method based on die casting experiments and mathematic modeling is presented for the determination of the heat flow density （HFD） and interfacial heat transfer coefficient （IHTC） during the high pressure die casting （HPDC） process.Experiments were carried out using step shape casting and a commercial magnesium alloy,AM50.Temperature profiles were measured and recorded using thermocouples embedded inside the die. Based on these temperature readings,the HFD and IHTC were successfully determined and the calculation results show that the HFD and IHTC at the metal-die interface increases sharply right after the fast phase injection process until approaching their maximum values,after which their values decrease to a much lower level until the dies are opened.Different patterns of heat transfer behavior were found between the die and the casting at different thicknesses.The thinner the casting was,the more quickly the HFD and IHTC reached their steady states.Also,the values for both the HFD and IHTC values were different between die and casting at different thicknesses.

Theoretical and experimental advances on heat transfer and flow characteristics of metal foams

Open cell metal foam can be applied to greatly improve thermal performance of heat sink and heat exchanger,so that it has been widely used in the fields of thermal(or heat)control system of aerospace vehicle and energy utilization system and become a very important topic for research in the aerospace thermophysics field,and more and more attentions have been attracted.The optimal design of metal foam heat transfer devices is based on the understanding the flow and heat transfer characteristics in metal foam.This article reviews some recent progresses of theoretical and experimental researches on heat transfer enhancement and flow characteristics of metal foam.We found that the pore cell simplification models of metal foams generally fall into four categories,among which the most commonly used cell model is Kelivin model.Some exploratory works performed by the current authors are also introduced,such as the effect of boundary conditions on the heat transfer enhancement;the theoretical modelling of interfacial convective heat transfer taking into account heat conduction between foam ligaments;and the flow characteristics under relatively high velocity.The analytical results show that the flow characteristics of metal foam at relatively high speed are completely different from those at low speed,a further thorough study of the heat transfer and flow characteristics of metal foam is necessarily required.In this paper,two types of partial filling techniques are discussed.The heat transfer performance of partially filled tubes was evaluated by both the performance evaluation criteria and the performance evaluation plot of enhanced heat transfer techniques oriented for energy-saving.The results show that the filling type of metal foam have a significant impact on its heat transfer enhancement performance.Therefore,the filling method of metal foam should be further studied,in order to optimize the thermophysical properties of heat transfer devices.

Directional solidification behavior of turbine blades in DZ125 alloy:design of blade numbers on assembly

The influence of blades assembly,i.e.,the blade number on the solidification process,heat exchange and grain structure on a directionally solidified Ni-based superalloy DZ125 was investigated by combining the experimental and simulation results.The casting process was simulated thermodynamically by ProCAST software,where the interface heat transfer coefficient was precisely determined by a measurement with thermocouples.There is a good agreement between experimental and simulation results.It was interestingly found that with the number of blades increasing from 6 to 10,due to the decrease in radiation absorption efficiency,the maximum temperature and the heating rate decrease in the mold,during the preheat process.During the withdrawal procedure,increased assembly numbers reduce the radiation exchange from mold to the enclosure,resulting in the decrease in cooling rate and temperature gradient of the blades.At the end of withdrawal,the slower cooling rate of the outside balances the temperature distribution of internal and external surfaces on the rabbet of blade.