Liquid Metal Grid Patterned Thin Film Devices Toward Absorption‑Dominant and Strain‑Tunable Electromagnetic Interference Shielding

The demand of high-performance thin-film-shaped deformable electromagnetic interference(EMI)shielding devices is increasing for the next generation of wearable and miniaturized soft electronics.Although highly reflective conductive materials can effectively shield EMI,they prevent deformation of the devices owing to rigidity and generate secondary electromagnetic pollution simultaneously.Herein,soft and stretchable EMI shielding thin film devices with absorption-dominant EMI shielding behavior is presented.The devices consist of liquid metal(LM)layer and LM grid-patterned layer separated by a thin elastomeric film,fabricated by leveraging superior adhesion of aerosol-deposited LM on elastomer.The devices demonstrate high electromagnetic shielding effectiveness(SE)(SE_(T) of up to 75 dB)with low reflectance(SER of 1.5 dB at the resonant frequency)owing to EMI absorption induced by multiple internal reflection generated in the LM grid architectures.Remarkably,the excellent stretchability of the LM-based devices facilitates tunable EMI shielding abilities through grid space adjustment upon strain(resonant frequency shift from 81.3 to 71.3 GHz@33%strain)and is also capable of retaining shielding effectiveness even after multiple strain cycles.This newly explored device presents an advanced paradigm for powerful EMI shielding performance for next-generation smart electronics.

Experimental studies of extraordinary light transmission through periodic arrays of subwavelength square and rectangular holes in metal films

We fabricate a series of periodic arrays of subwavelength square and rectangular air holes on gold films, and measure the transmission spectra of these metallic nanostructures. By changing some geometrical and physical parameters, such as array period, air hole size and shape, and the incident light polarization, we verify that both global surface plasmon resonance and localized waveguide mode resonance are influential on enhancing the transmission of light through nanostructured metal films. These two resonances induce different behaviours of transmission peak shift. The transmission through the rectangular air-hole structures exhibits an obvious polarization effect dependent on the morphology. Numerical simulations are also made by a plane-wave transfer-matrix method and in good consistency with the experimental results.

Annealing effects of Sn-Al and Sn-Cu nano thin films on mechanism of electromagnetic interference shielding

The sputtered Sn-Al and Sn-Cu thin films were used to investigate the effects of the crystallization mechanism and film thickness on the electromagnetic interference （EMI） characteristics. In addition, the annealed microstructure, electrical conductivities and EMI characteristics of the Sn-xAl films and the Sn-xCu films were compared. The results show that the electromagnetic interference （EMI） shielding of Sn-Al film was increased after annealing. For the Sn-Cu films with higher Cu mole concentration, the low frequency EMI shielding could not be improved. After annealing, the Sn-Cu thin film with lower Cu mole concentration possesses excellent EMI shielding at lower frequencies, but has an inverse tendency at higher frequencies.

Efficiency analysis of a-SiC:H thin film light emitting diodes

The hole injection,the radiative recombination and the device luminescent efficiencies of amorphous silicon carbide thin film p-i-n junction light emitting diodes are quantitatively calculated,and the effect of the carrier(especially the hole) injection and recombination processes on the device luminescent characteristics are revealed.Without considering the device junction temperature,it is found that the device luminescent efficiency mainly depends on the hole injection efficiency at low field and the hole radiative recombination efficiency at high field respectively.The theoretical analyses are in well agreement with the experimental results.

Surface Plasmon Interference Lithography Assisted by a Fabry-Perot Cavity Composed of Subwavelength Metal Grating and Thin Metal Film

A surface plasmon interference lithography assisted by a Fabry-Perot （F-P） cavity composed of subwavelength metal gratings and a thin metal fihn is proposed to fabricate high-quality nanopatterns. The calculated results indicate that uniform straight interference fringes with high contrast and high electric-field intensity are formed in the resist under the F-P cavity. The analyses of spatial frequency spectra illuminate the physical mechanism of the formation for the interference fringes. The influence of the F-P cavity spacing is discussed in detail. Moreover, the error analyses reveal that all parameters except the metal grating period in this scheme can bear large tolerances for the device fabrication.

Development of Dual-light Path Monitoring System of Optical Thin-film Thickness

The accurate monitoring of optical thin-film thickness is a key technique for depositing optical thin-film. For existing coating equipments, which are low precision and automation level on monitoring thin-film thickness, a new photoelectric control and analysis system has been developed. In the new system, main techniques include a photoelectric system with dual-light path, a dual-lock-phase circuit system and a comprehensive digital processing-control-analysis system.The test results of new system show that the static and dynamic stabilities and the control precision of thin-film thickness are extremely increased. The standard deviation of thin-film thickness, which indicates the duplication of thin-film thickness monitoring, is equal to or less than 0.72%. The display resolution limit on reflectivity is 0.02 %. In the system, the linearity of drift is very high, and the static drift ratio approaches zero.

Characteristic improvements of thin film AlGaInP red light emitting diodes on a metallic substrate

We report a type of thin film Al Ga In P red light emitting diode（RLED） on a metallic substrate by electroplating copper（Cu） to eliminate the absorption of Ga As grown substrate.The fabrication of the thin film RLED is presented in detail.Almost no degradations of epilayers properties are observed after this substrate transferred process.Photoluminescence and electroluminescence are measured to investigate the luminous characteristics.The thin film RLED shows a significant enhancement of light output power（LOP） by improving the injection efficiency and light extraction efficiency compared with the reference RLED on the Ga As parent substrate.The LOPs are specifically enhanced by 73.5% and 142% at typical injections of 2 A/cm^2 and 35 A/cm^2 respectively from electroluminescence.Moreover,reduced forward voltages,stable peak wavelengths and full widths at half maximum are obtained with the injected current increasing.These characteristic improvements are due to the Cu substrate with great current spreading and the back reflection by bottom electrodes.The substrate transferred technology based on electroplating provides an optional way to prepare high-performance optoelectronic devices,especially for thin film types.

Electrodeposition of Cu_2O/g-C_3N_4 heterojunction film on an FTO substrate for enhancing visible light photoelectrochemical water splitting

An immobilized Cu2O/g-C3N4 heterojunction film was successfully made on an FTO substrate by electrophoretic deposition of g-C3N4 on a Cu2O thin film.The photoelectrochemical（PEC） performance for water splitting by the Cu2O/g-C3N4 film was better than pure g-C3N4 and pure Cu2O film.Under-0.4 V external bias and visible light irradiation,the photocurrent density and PEC hydrogen evolution efficiency of the optimized Cu2O/g-C3N4 film was-1.38 mA/cm^2 and 0.48 mL h^-1 cm^-2,respectively.The enhanced PEC performance of Cu2O/g-C3N4 was attributed to the synergistic effect of light coupling and a matching energy band structure between g-C3N4 and Cu2O as well as the external bias.

Light Simplified Cultivation Techniques of Wide Row and Double Ridge with Filming, Fertilizing and Sowing on One for Foxtail Millet

In view of the problems of completely depending on rain, low and unstable yield and complicated planting of dry land foxtail millet, the light simplified cultivation techniques of wide row and double ridge with filming, fertilizing and sowing on one for foxtail millet was formed through the integration of plastic film mulching technology and mechanized production technology by Institute of Millet crops of Hebei Academy of Agriculture and Forestry Sciences, and the techniques were introduced from the key technologies of pre-sowing preparation, sowing, supporting equipment, field management, harvesting, plastic film recycling.

Flexible, Transparent and Conductive Metal Mesh Films with Ultra‑High FoM for Stretchable Heating and Electromagnetic Interference Shielding

Despite the growing demand for transparent conductive films in smart and wearable electronics for electromagnetic interference(EMI)shielding,achieving a flexible EMI shielding film,while maintaining a high transmittance remains a significant challenge.Herein,a flexible,transparent,and conductive copper(Cu)metal mesh film for EMI shielding is fabricated by self-forming crackle template method and electroplating technique.The Cu mesh film shows an ultra-low sheet resistance(0.18Ω□^(-1)),high transmittance(85.8%@550 nm),and ultra-high figure of merit(>13,000).It also has satisfactory stretchability and mechanical stability,with a resistance increases of only 1.3%after 1,000 bending cycles.As a stretchable heater(ε>30%),the saturation temperature of the film can reach over 110°C within 60 s at 1.00 V applied voltage.Moreover,the metal mesh film exhibits outstanding average EMI shielding effectiveness of 40.4 dB in the X-band at the thickness of 2.5μm.As a demonstration,it is used as a transparent window for shielding the wireless communication electromagnetic waves.Therefore,the flexible and transparent conductive Cu mesh film proposed in this work provides a promising candidate for the next-generation EMI shielding applications.

MXene@c-MWCNT Adhesive Silica Nanofiber Membranes Enhancing Electromagnetic Interference Shielding and Thermal Insulation Performance in Extreme Environments

A lightweight flexible thermally stable composite is fabricated by com-bining silica nanofiber membranes(SNM)with MXene@c-MWCNT hybrid film.The flexible SNM with outstanding thermal insulation are prepared from tetraethyl orthosilicate hydrolysis and condensation by electrospinning and high-temperature calcination;the MXene@c-MWCNT_(x:y)films are prepared by vacuum filtration tech-nology.In particular,the SNM and MXene@c-MWCNT_(6:4)as one unit layer(SMC_(1))are bonded together with 5 wt%polyvinyl alcohol(PVA)solution,which exhibits low thermal conductivity(0.066 W m^(-1)K^(-1))and good electromagnetic interference(EMI)shielding performance(average EMI SE_(T),37.8 dB).With the increase in func-tional unit layer,the overall thermal insulation performance of the whole composite film(SMC_(x))remains stable,and EMI shielding performance is greatly improved,especially for SMC_(3)with three unit layers,the average EMI SET is as high as 55.4 dB.In addition,the organic combination of rigid SNM and tough MXene@c-MWCNT_(6:4)makes SMC_(x)exhibit good mechanical tensile strength.Importantly,SMC_(x)exhibit stable EMI shielding and excellent thermal insulation even in extreme heat and cold environment.Therefore,this work provides a novel design idea and important reference value for EMI shielding and thermal insulation components used in extreme environmental protection equipment in the future.

Mitigation of inter-cell interference in visible light communication

This paper proposes the orthogonal and nonorthogonal schemes in the interference environments for visible light communication（ VLC） systems. The proposed schemes pay attention to the case when different bit streams from multiple cells are simultaneously transmitted, which consequently causes inter-cell interference（ ICI） and greatly deteriorates the bit error rate（ BER） and channel capacity performance of the system. The performance of the newdeveloped multi-cell system in indoor VLC systems is evaluated. The bipolar phase shift keying（ BPSK） modulation scheme with orthogonal pulses（ OPs） for multiple cells environments is employed to mitigate the ICI problem and improve the BER and channel capacity performances. Since the use of different OPs in each cell requires more number of OPs, which requires high bandwidth, OPs are reused at certain distances. Three different schemes, which are OPs,orthogonal and non-orthogonal pulses（ NOP） reuse, are compared. This paper investigates the impact of using these schemes and compared their performances in the ICI environments. The BER and channel capacity using the proposed schemes are comprehensively examined. Simulation and theoretical results showthat the OPs schemes are more effective in the interference areas of the room and significantly outperform NOP.

Design of non-polarizing thin film edge filters

The separation between s- and p-polarization components invariably affects thin film edge filters used for tilted incidence and is a difficult problem for many applications, especially for optical communication. This paper presents a novel design method to obtain edge filters with non-polarization at incidence angle of 45°. The polarization separation at 50% trans-mittance for a long-wave-pass filter and a short-wave-pass filter is 0.3 nm and 0.1 nm respectively. The design method is based on a broadband Fabry-Perot thin-film interference filter in which the higher or lower interference band at both sides of the main transmittance peak can be used for initial design of long-wave-pass filter or short-wave-pass filter and then can be refined to reduce the transmittance ripples. The spacer 2H2L2H or 2L2H2L of the filter is usually taken. Moreover, the method for expanding the bandwidth of rejection and transmission is explained. The bandwidth of 200 nm for both rejection region and transmission band is obtained at wavelength 1550 nm. In this way, the long-wave-pass and short-wave-pass edge filters with zero separation between two polarization components can easily be fabricated.

Review of blue perovskite light emitting diodes with optimization strategies for perovskite film and device structure

Perovskite light emitting diodes(PeLEDs)have attracted considerable research attention because of their external quantum efficiency(EQE)of>20%and have potential scope for further improvement.However,compared to red and green PeLEDs,blue PeLEDs have not been extensively investigated,which limits their commercial applications in the fields of luminance and full-color displays.In this review,blue-PeLED-related research is categorized by the composition of perovskite.The main challenges and corresponding optimization strategies for perovskite films are summarized.Next,the novel strategies for the design of device structures of blue PeLEDs are reviewed from the perspective of transport layers and interfacial layers.Accordingly,future directions for blue PeLEDs are discussed.This review can be a guideline for optimizing perovskite film and device structure of blue PeLEDs,thereby enhancing their development and application scope.

Formation and Gas Barrier Characteristics of Polysilazane-Derived Silica Coatings Formed by Excimer Light Irradiation on PET Films with Vacuum Evaporated Silica Coatings

The effects of excimer light irradiation on polysilazane coatings formed on PET films with vacuum-evaporated SiO2 coatings and the effects of these coatings on gas barrier characteristics have been investigated. The temperature during light irradiation has a large effect on the coating’s molecular structure and gas barrier characteristics. When irradiation was performed at 100℃, the polysilazane coating transformed into a silica coating, and a compact silica coating at a much lower temperature than with heat treatment alone was produced. Surface irregularities in the vapor-deposited silica coating were smoothed out by the formation of a polysilazane coating, which was transformed into a compact silica coating when irradiated with light, resulting in a significant improvement in the gas barrier characteristics. The water vapor permeability of the thin coating irradiated with excimer light at 100℃ showed only 0.04 g/m2•day (40℃, 90% RH). According to the results of investigation of temperature variation of water-vapor permeability, it is inferred that the developed film has an excellent gas barrier value, namely, 4.90 × 10–4 g/m2•day at 25℃. This gas barrier coated PET film is transparent and flexible, and can be used in the fabrication of flexible electronics. Also, the proposed fabrication method effectively provides a simple low-cost and low-temperature fabrication technique without the need for high vacuum facility.

THE LIGHT INDUCED CHANGE IN TRANSIENT PHOTOCONDUC-TIVITY OF POLYMORPHOUS SILICON FILMS

The decays of transient photoconductivity and their light-induced changes of polymorphous silicon (pm-Si:H) films were investigated. The decays can be fit fairly well by a sum of two exponential decay functions, which indicates that there are two kinds of traps contributing to the process. The light-induced changes of the concentration and energy level of the traps were estimated. The results show that the light-induced changes in trap energy position Et, trap concentration Nt as well as photoconductivity are markedly less for pm-Si:H than that for a-Si:H.

Annealing Temperature-Dependent Luminescence Color Coordination in Eu-Doped AlN Thin Films

AlN was used as a host material and doped with Eu grown on Si substrate by pulsed laser deposition (PLD) with low substrate temperature. The X-ray diffraction (XRD) data revealed the orientation and the composition of the thin film. The surface morphology was studied by scanning electron microscope (SEM). While raising the annealing temperatures from 300˚C to 900˚C, the emission was observed from AlN: Eu under excitation of 260 nm excitation. The photoluminescence (PL) was integrated over the visible light wavelength shifted from the blue to the red zone in the CIE 1931 chromaticity coordinates. The luminescence color coordination of AlN: Eu depending on the annealing temperatures guides the further study of Eu-doped nitrides manufacturing on white light emitting diode (LED) and full color LED devices.

Inter‑Skeleton Conductive Routes Tuning Multifunctional Conductive Foam for Electromagnetic Interference Shielding,Sensing and Thermal Management

Conductive polymer foam(CPF)with excellent compressibility and variable resistance has promising applications in electromagnetic interference(EMI)shielding and other integrated functions for wearable electronics.However,its insufficient change amplitude of resistance with compressive strain generally leads to a degradation of shielding performance during deformation.Here,an innovative loading strategy of conductive materials on polymer foam is proposed to significantly increase the contact probability and contact area of conductive components under compression.Unique inter-skeleton conductive films are constructed by loading alginate-decorated magnetic liquid metal on the polymethacrylate films hanged between the foam skeleton(denoted as AMLM-PM foam).Traditional point contact between conductive skeletons under compression is upgraded to planar contact between conductive films.Therefore,the resistance change of AMLM-PM reaches four orders of magnitude under compression.Moreover,the inter-skeleton conductive films can improve the mechanical strength of foam,prevent the leakage of liquid metal and increase the scattering area of EM wave.AMLM-PM foam has strain-adaptive EMI shielding performance and shows compression-enhanced shielding effectiveness,solving the problem of traditional CPFs upon compression.The upgrade of resistance response also enables foam to achieve sensitive pressure sensing over a wide pressure range and compression-regulated Joule heating function.

Light scattering of nanocrystalline TiO_2 film used in dye-sensitized solar cells

This paper studies the light scattering and adsorption of nanocrystalline TiO2 porous films used in dye-sensitized solar cells composed of anatase and/or rutile particles by using an optical four-flux radiative transfer model. These light properties are difficult to measure directly on the functioning solar cells and they can not be calculated easily from the first-principle computational or quantitative theoretical evaluations. These simulation results indicate that the light scattering of 1 25 nm TiO2 particles is negligible, but it is effective in the range of 80 and 180 nm. A suitable mixture of small particles （10 nm radius）, which are resulted in a large effective surface, and of larger particles （150 nm radius）, which are effective light scatterers, have the potential to enhance solar absorption significantly. The futile crystals have a larger refractive index and thus the light harvest of the mixtures of such larger rutile and relatively small anatase particles is improved in comparison with that of pure anatase films. The light absorption of the 10μm double-layered films is also examined. A maximal light absorption of double-layered film is gotten when the thickness of the first layer of 10 urn-sized anatase particles is comparable to that of the second larger rutile layer.

The Application of Lights-Conversed Polyethylene Film for Agriculture

Lanthanum-rhodamine (6G and B) complexes were synthesized by Rheological Phase Reaction Method. Lanthanum-rhodamine (6G and B) complexes doped polyethylene films which have a function of lights-conversion were prepared. The emission and excitation spectra were measured. The experiments of growing seedling and culture were carried out in the shed built with doped and undoped polyethylene films. Lanthanum-rhodamine doped polyethylene films which have a function of lights-conversion can efficiently convert the green light in the sunlight to the red light for photosynthesis of crops, to promote the maturing of crops and raise the yield of crops.