Application of 3D GPR attribute technology in archaeological investigations

Ground penetrating radar （GPR） attribute technology has been applied to many aspects in recent years but there are very few examples in the field of archaeology. Especially how can we extract effective attributes from the two- or three-dimensional radar data so that we can map and describe numerous archaeological targets in a large cultural site？ In this paper, we applied GPR attribute technology to investigate the ancient Nanzhao castle-site in Tengchong, Yunnan Province. In order to get better archaeological target （the ancient wall, the ancient kiln site, and the ancient tomb） analysis and description, we collated the GPR data by collected standardization and then put them to the seismic data processing and interpretation workstation. The data was processed, including a variety of GPR attribute extraction, analysis, and optimization and combined with the archaeological drilling data. We choose the RMS Amplitude, Average Peak Amplitude, Instantaneous Phase, and Maximum Peak Time to interpret three archaeological targets. By comparative analysis, we have clarified that we should use different attributes to interpret different archaeological targets and the results of attribute analysis after horizon tracking is much better than the results based on a time slice.

Incident prevention tools-incident investigations and pre-job safety analyses

Careful and thorough incident investigations and pre-job safety analyses completed by knowledgeable and competent individuals can significantly reduce workplace incidents. Working parties must act together to make these safety tools effective. To get the staff units to work together in a co-ordinated manner, they must be shown the value of their work in preventing accidents. Examples of actual accidents investigated during the author's 18 years as a mine inspector in Saskatchewan are discussed within the context of pre-job safety analyses. The causes of the accidents are explored with close reference to how pre-job safety analyses could have prevented their occurrence.

Numerical investigations on effects of bluff body in flat plate micro thermo photovoltaic combustor with sudden expansion

In order to reveal combustion characteristics of H_2/air mixture in a micro-combustor with and without bluff body, the effects of inlet velocities, equivalence ratios and bluff body's blockage ratios on the temperature field, pressure of the combustor wall, combustion efficiency and blow-off limit were investigated. The numerical results indicate that the sudden expansion plate micro combustor with bluff body could enhance the turbulent disturbance of the mixed gas in the combustion chamber and the combustion condition is improved. Moreover, a low-speed and high temperature recirculation region was formed between the sudden expansion step and the bluff body so that the high and uniform wall temperature(>1000 K) could be gotten. As a result, it could strengthen the mixing process, prolong the residence time of gas, control the flame position effectively and widen the operation range by the synergistic effect of the bluff body and steps. When the blockage ratio ranged from 0.3 to 0.6, it could be found that the bluff body could play a stabilizing effect and expand combustion blow burning limit, and combustion efficiency firstly was increased with the inlet velocity and equivalence ratio, and then was decreased.

First contact investigations and compliance to treatment in patients with uveitis

AIM:To ascertain the pattern of investigations at first contact in uveitic patients and evaluate compliance to treatment.METHODS:An observational study comprised of 201 uveitic patients presenting for the first time to our centre from January 2019 to June 2020.Detailed information regarding systemic investigations undertaken by specialists at the time of first contact and the cost of these investigations were reviewed on the first visit to our centre.Compliance with the treatment was determined and reasons behind non-compliance were evaluated on the first follow-up in patients who had no improvement in clinical signs and symptoms.RESULTS:The mean age of the study group was 35.35±14.1y and gender composition was 59.7%males and 40.3%females.Anterior uveitis was observed in 45.3%of patients,intermediate uveitis in 31.8%of patients,posterior uveitis in 14.9%of patients and panuveitis in 8.0%of patients.Association with a systemic disease was evident in 17.9%of patients.When compared with standard guidelines and uveitis patterns,systemic investigations were identified to be relevant only in 38.3%of patients.Non-compliance to treatment was documented in 22.4%of patients.Common reasons for non-compliance were inadequate counselling by the treating physician about treatment in 26.7%of patients and a busy schedule at work/school in 22.2%of patients.CONCLUSION:Significant number of investigations performed at first contact is found to be contrary to standard guidelines and are not contributory to the care.About a quarter of patients in this study are found to be non-compliant with the treatment.Compliance is more challenging to achieve in school-going children and working adults.The availability of comprehensive,periodically updated,evidence-based guidelines on the role of investigations and the use of trained counsellors may help to channelize proper evaluation and improve compliance to treatment,respectively,in patients with uveitis.

A Precise Description of the Electronic Structures and Spin-Allowed Transition Properties of PF and Its Cation:All-Electron Configuration-Interaction Investigations Including Relativistic Effect

The electronic structures of PF and PF＋ are calculated with the high-level configuration interaction method. To improve the precision of calculations, the spin-orbit coupling effect, the scalar relativistic effect, and the Davidson correction（q-Q） are also considered. The spectroscopic parameters of bound states are derived by the electronic structures of PF and PF＋, which are in good accordance with the measurements. The transition dipole moments of spin-allowed transitions are evaluated, and the radiative lifetimes of several A S states of PF and PF＋ are obtained.

Powder Metallurgical Fabrication and Microstructural Investigations of Aluminum/Steel Functionally Graded Material

Aluminum/steel electric transition joints (ETJs) are used in aluminum reduction cell for the purpose of welding aluminum rod and steel bracket components. Solid state welding process used for joining aluminum and steel at the electric transition joints have the drawbacks of cracking and separation at the interface surfaces. Cracking and separation at the electric transition joints are caused by the stress singularities that developed due to the mismatch in thermal and mechanical properties of each material. To overcome the drawback of electric transition joints, aluminum/steel functionally graded may be used as electric transition joints or proposed. Therefore manufacturing and investigation of aluminum/steel functionally graded materials fabricated by powder metallurgy process were carried out through the current work. Different samples with different layers of aluminum/steel functionally graded materials were compacted using steel die and punch at the same compacted pressure and sintered temperature. After investigating the different samples of aluminum/steel functionally graded materials under different fabrication conditions, the suitable fabrication regime was determined with the aid of microscopic observations.

First-Principles Investigations of Pb_(0.5)Ba_(0.5)TiO_3 Alloys Based on Structure Predictions

Crystal structure predictions of Pb0.5Ba0.5 Ti03 alloys under different pressures are performed based on the parti- cle swarming optimization algorithm. The predicted stable ground-state and high-pressure phases are tetragonal ferroelectric （I4mm） and cubic para-electric （Fm3m）, respectively, whose structural details have not been re- ported. The pressure-induced colossal enhancements in piezoelectric response are associated with the mechanical and dynamical instabilities instead of polarization rotation. The band gap of the tetragonM phase is indirect and that of the cubic phase is always direct. As pressure increases, the alloy displays the similar band-gap behaviors to PbTiO3, while different from BaTiO5, which is attributed to the different orbital contributions to the valence bands. Our calculated results are in good agreement with the available data.

INVESTIGATIONS ON NANOMETER-SIZED ULTRAMICRO-ELECTRODES(Ⅱ)—FABRICATION, CHARACTERIZATION OF CARBON FIBER CYLINDER ULTRAMICROELECTRODES

Described here are the fabrication and characterization of carbon fiber cylinder ultramicroelectrodes with cylinder length of less than 100 am, total tip diameter of several hundreds nanometers. The electrodes have been fabricated by direct etching of carbon fiber using an ion beam thinner. Optical microscopy, scanning electron microscopy (SEM), cyclic voltammetry have been employed to characterize those electrodes. The experimental results obtained indicate the electrodes can be used for in vivo detection of neurotransmitters such as dopamine, 5—hydroxytryptamine in a single cell.

EPR and Magnetic Susceptibility Investigations of Fe Containing TeO_2-B_2O_3-SrF_2 Glasses

Iron ions were used as probes to explore the structural and magnetic properties of 70TeO2'25B2O3' 5SrF2 vitreous matrix. The distribution of Fe3+ ions on different structural aggregates was revealed by means of EPR, as depending on Fe2O3 concentration. Strongly distorted octahedral sites were detected for the isolated paramagnetic ions, and also clusters of Fe ions especially at high Fe2O3 content of samples. Magnetic susceptibility measurements evidenced both dipoledipole and superexchange type interactions involving iron ions. Mixed valence states of iron ions were also detected

Dynamic Investigations of Pressure-Induced Abnormal Phase Transitions in PbTiO3

The effects of pressure on phonon modes of ferroeleetrie tetragonal P4mm and paraelectric cubic Pm3m PbTiOa are systematically investigated by using first-principles simulations. The pressure-induced tetragonal-to-cubie and subsequent cubic-to-tetragonal phase transitions are the second-order transitions, which are different from the phase transitions induced by temperature [Phys. Rev. Lett. 25 （1970） 167]. As pressure increases, the lowest A1 and E modes of the tetragonal phase become softer and converge to the F1u mode of the cubic phase. As pressure further increases, the lowest Flu mode first hardens and then softens again, and finally diverges into A1 and E modes. The behaviors of optical phonon modes confirm the ferroelectric-to-paraelectric-to-ferroeleetric phase transitions.

Preyminary Investigations on the Global Summer Monsoonal Drought Mechanics and the Latitudinal Teleconnections

The question of possible teleconnections between the middle latitude general circulation and the Indian south-west monsoon was investigated in this paper. Within the framework of a simple model it was shown that there can exist such an interaction via the ultra-long Rossby waves.

Off-Shore Sea Surface Electric Field Investigations around the Indian Sub-Continent during 9-20 May 1983

Sea surface electric field observations off the coast from Goa (15°25'N, 73°47'E) to Madras (13°04'N, 80°15'E) around Sri Lanka, in a distance range 25-135 km from coast, during 9-20 May 1983 were taken. In this paper we have examined the diurnal variation of electric field in the Arabian Sea, Indian Ocean and Bay of Bengal regions covered during the cruise of the research ship ORV Gaveshani. An aspect of electric field dependence on coastal distance and Aitken Nuclei concentration has also been studied. An attempt to examine the latitude dependence of field was also made. Results obtained in the above studies are presented and compared with those obtained elsewhere.

Ground Penetrating Radar (GPR) Investigations for Architectural Heritage Preservation: The Case of Habib Sakakini Palace, Cairo, Egypt

A comprehensive Ground Penetration Radar (GPR) investigations and hazard assessment for the rehabilitation and strengthening of Habib Sakakini’s Palace in Cairo is presented herein, which is considered one of the most significant architectural heritage sites in Egypt. The palace located on an ancient water pond at the eastern side of Egyptian gulf besiding Sultan Bebris Al-Bondoqdary mosque is a place also called “Prince Qraja al-Turkumany pond”. That pond had been filled down by Habib Sakakini at 1892 to construct his famous palace in 1897. The integrated geophysical survey of the palace allowed the identification of several targets of potential archaeological and geotechnical engineering interest buried in fill and silty clay in the depth range between 100 - 700 cm. the methodological development focused on Multi-Fold (MF) Ground Penetrating Radar (GPR) imaging and subsurface characterization based on integrated velocity and attenuation analysis. Eight hundred sqm of Ground penetration Radar (GPR) profiling have been conducted to monitor the subsurface conditions. 600 meters are made in the surrounding area of the Palace and 200 sqm at the basement. The aim is to monitor the soil conditions beneath and around the Palace and to identify potential geological discontinuities, or the presence of faults and cavities. A suitable single and dual antenna are used (500 - 100 MHZ) is used to penetrate the desired depth of 7 meters (ASTM D6432). The GPR is used also detect the water table. At the building basement the GPR is used to identify the foundation thickness and soil-basement interface. As well as the inspection of cracks in some supporting columns, piers and masonry walls. The GPR also was used to investigate the floors and ceilings conditions and structural mapping. The results were validated by the geotechnical and structural surveys. All these results together with the seismic hazard analysis will be used for the complete analysis of the palace in the framework of the rehabilitation and strengthening works foreseen in a second stage.

INVESTIGATIONS ON SOME METALS AND THEIR OXIDES BY NIIR

A new type of saddle field ion gun has been developed in our laboratories, and it can emit ions and a large proportion of energetic neutrals.The ion gun has been used in the neutral and ion impact radiation （NIIR） spectrometer to decrease the effect of charge accumulation on the surfaces of specimens. Some metals, including aluminium, copper and nickel and their oxides had been analysed by NIIR. By comparing the intensities of the spectral lines of the above metals and their oxides the intensification effect due to oxidation had been found. The ratio of intensities between Al I（3962（?）） for Al2O3 and Al I （3962（?）） for Al is 120, so the effect can be seen clearly from the above experimental results. The mechanism of the intensification effect has been discussed in the paper.

A Review of Marine Safety Investigations Success Barriers

This study reveals the most known barriers to successful marine safety investigations important role of effective marine accident investigation in the improvement of the maritime safety through prevention similar casualties from occurring in the future and explores the legal obligations of all parties under different international maritime conventions and codes.Since marine safety investigations results and recommendations are important for the maritime safety,so this paper determines,the shortage of application of the international regulations adopted by IMO related to maritime safety,and the shortage of legal measures to support safety at sea and protection or reduce marine pollution.This paper also aims to improve special measures for procedures of marine accident investigation and highlights the importance of identifying the liability and effective recommendations.

Development of New Interspecific Monosomic F_1 Substitution Stocks for Investigations in Cotton Genome

As it is known a complete coverage of cotton(Gossypium hirsutum L.) genome with hypoaneuploids is not still realized.Therefore the detection of new types of aneuploids especially in different cytogenetic collections is very useful.In Uzbekistan,long-term investigations towards development

The Role of Urine Investigations in Urology Practice

Urine examination is one of the important armamentarium in the practice of urology and it is a fundamental test that is usually carried out for urology patients, it can be as simple as dipstick analysis to a complex hormonal assays. Urine examination is done worldwide as an extension of physical examination which provides a lot of information about the pathology, and both physical and chemical analysis of urine are highly informative. There are several types of urine investigations, some of which include urinalysis, urine microscopy culture and sensitivity, urine microscopy for ova or cyst of parasites, urine cytology, urine tumour antigens assays, urine hormonal assays, urine toxicology, urine quantitative measurement and urine acid fast bacilli. Uses of urine examinations in urology could be diagnostic, such as renal function test, evaluation of heamaturia, stone diseases, urinary tract infections, urologic cancers and infertility or monitoring and for prognosis. Uses of urine investigations in practice of urology cannot be over emphasized as it has many revealing information of the physiology and pathology of urologic organs.

Development and Implementation of Constant Friction Power Control in a Reduced Scale Brake Dynamometer for Investigations of Automotive Brake Systems

For tribological investigations of automotive brakes, both full and reduced scale brake dynamometers are used. Full scale brake dynamometers test the entire brake system, including caliper, brake pad, brake disk, wheel suspension, etc. The AUT （automated universal tribotester） is a reduced scale brake dynamometer with a pin on disk test configuration. A brake pad specimen is used as the pin and a brake disk is used as the counter body. Compared to full scale brake dynamometers, the AUT encounters fewer influences from the test systems themselves. The AUT was developed at the Institute of Dynamics and Vibrations in Braunschweig. It can be used for high frequency analyses of the coefficient of friction, and investigations of the boundary layer between brake pad and disk, along with the associated NVH behaviors. A digital camera and two laser triangulation sensors are used for optical investigations of the brake pad and brake disk [1, 2]. The focus of this paper is the development of a new control feature of the AUT. The AUT employs a compactRIO from National Instruments as its measurement and control device. The velocity and position control loops are implemented in the compactRIO＇s FPGA along with high frequency synchronous measurement data acquisition. Its real-time controller coordinates the measurement and the storage of measured data. The test device has three degrees of freedom： normal load, sliding speed, and temperature, all of which can be defined by the user for each brake application. New control strategies based on the friction force as a feedback parameter allow for the implementation of new features. In this paper, the realization of measurements with constant friction power throughout the friction procedure will be shown. This new degree of freedom in the friction measurements enables investigations to be carried out in which it is necessary to bring a specific energy in the friction process. In this paper, a p-controller on the real-time system calculates the required set point for the position control loop. The new feature is verified through a benchmark test [6]. Based on the control loop with the friction force as the feedback parameter, it is also possible to emulate in-stop brakes with virtual inertia. In this way, many other types of full scale brake dynamometers can be simulated. The long-term aim is the identification of the influence of test devices on the test results.

Analysis of Epidemiological Investigations and Responses to Human Rabies Deaths in Côte d’Ivoire, 2021

Rabies is an infectious disease that almost always leads to death as soon as the first signs appear, and is still endemic in several regions, including Côte d’Ivoire. Epidemiological investigations are carried out and response measures implemented in the event of any death from human rabies. However, the quality of these investigations does not always allow the adoption of response measures. The aim of this work was to evaluate the reports of epidemiological investigations and response actions carried out during the occurrence of human rabies deaths from 2016 to 2018. This was a cross-sectional study that took place from April to September 2021 at the National Institute of Public Hygiene and focused on human rabies deaths notified from 206 to 2018. Of sixty-one (61) human rabies deaths recorded, sixty (60) were investigated, among which fifty-nine (59) deaths had been subject to response. Most deaths occurred in rural areas (75%), and the main vector was the dog (98%). Several shortcomings were noted: response actions were not carried out promptly;joint interventions bringing together human and animal health professionals were rare, there was little communication about rabies to communities (36%), and very little vaccination of the vector, the source of the disease (12%);an almost total absence of capacity-building for local players (7%);the health districts of Abobo-Ouest, Bondoukou, Divo and Fresco, which had regularly recorded human rabies deaths, had not benefited from dog vaccination, which is supposed to break the circulation of the virus. The persistence of rabies deaths in the health districts could probably be linked to these shortcomings. Faced with these realities, it is essential to strengthen the epidemiological investigation capacities of the players involved, in order to improve the quality of investigations and ensure an effective response.

3-11 Transmission Electron Microscopy Investigations of Bubble Formation along GBs in He-implanted Polycrystalline SiC

Because of the low cross-section for neutron capture and its excellent structural, chemical and mechanicalstability, silicon carbide (SiC) is an important material with application in the development of nuclear energyand waste technologies. The (n,) nuclear reaction inevitably introduces numerous He in SiC. Because of the lowsolubility of He atoms in SiC, a certain concentration of He atoms that are trapped in the matrix in the formof helium-vacancy clusters would form bubbles upon annealing. He bubbles would perhaps lead to degradation ofmaterial properties. Especially, He bubbles along Grain boundaries (GBs) can cause embrittlement by intergranularfracture, as usually observed in metals. Therefore, it is important to investigate the nucleation and growth of Hebubbles along GBs in He-implanted SiC.