A low hole injection efficiency for InGaN/GaN micro-light-emitting diodes(μLEDs) has become one of the main bottlenecks affecting the improvement of the external quantum efficiency(EQE) and the optical power. In this...A low hole injection efficiency for InGaN/GaN micro-light-emitting diodes(μLEDs) has become one of the main bottlenecks affecting the improvement of the external quantum efficiency(EQE) and the optical power. In this work, we propose and fabricate a polarization mismatched p-GaN/p-Al_(0.25)Ga_(0.75)N/p-GaN structure for 445 nm GaN-based μLEDs with the size of 40 × 40 μm^(2), which serves as the hole injection layer. The polarization-induced electric field in the p-GaN/p-Al_(0.25)Ga_(0.75)N/p-GaN structure provides holes with more energy and can facilitate the non-equilibrium holes to transport into the active region for radiative recombination. Meanwhile, a secondary etched mesa for μLEDs is also designed, which can effectively keep the holes apart from the defected region of the mesa sidewalls, and the surface nonradiative recombination can be suppressed. Therefore, the proposed μLED with the secondary etched mesa and the p-GaN/p-Al_(0.25)Ga_(0.75)N/p-GaN structure has the enhanced EQE and the improved optical power density when compared with the μLED without such designs.展开更多
The comparison of domestic and foreign studies has been utilized to extensively employ junction termination extension(JTE)structures for power devices.However,achieving a gradual doping concentration change in the lat...The comparison of domestic and foreign studies has been utilized to extensively employ junction termination extension(JTE)structures for power devices.However,achieving a gradual doping concentration change in the lateral direction is difficult for SiC devices since the diffusion constants of the implanted aluminum ions in SiC are much less than silicon.Many previously reported studies adopted many new structures to solve this problem.Additionally,the JTE structure is strongly sensitive to the ion implantation dose.Thus,GA-JTE,double-zone etched JTE structures,and SM-JTE with modulation spacing were reported to overcome the above shortcomings of the JTE structure and effectively increase the breakdown voltage.They provided a theoretical basis for fabricating terminal structures of 4H-SiC PiN diodes.This paper summarized the effects of different terminal structures on the electrical properties of SiC devices at home and abroad.Presently,the continuous development and breakthrough of terminal technology have significantly improved the breakdown voltage and terminal efficiency of 4H-SiC PiN power diodes.展开更多
Molten-alkali etching has been widely used to reveal dislocations in 4H silicon carbide(4H-SiC),which has promoted the identification and statistics of dislocation density in 4H-SiC single crystals.However,the etching...Molten-alkali etching has been widely used to reveal dislocations in 4H silicon carbide(4H-SiC),which has promoted the identification and statistics of dislocation density in 4H-SiC single crystals.However,the etching mechanism of 4H-SiC is limited misunderstood.In this letter,we reveal the anisotropic etching mechanism of the Si face and C face of 4H-SiC by combining molten-KOH etching,X-ray photoelectron spectroscopy(XPS)and first-principles investigations.The activation energies for the molten-KOH etching of the C face and Si face of 4H-SiC are calculated to be 25.09 and 35.75 kcal/mol,respectively.The molten-KOH etching rate of the C face is higher than the Si face.Combining XPS analysis and first-principles calculations,we find that the molten-KOH etching of 4H-SiC is proceeded by the cycling of the oxidation of 4H-SiC by the dissolved oxygen and the removal of oxides by molten KOH.The faster etching rate of the C face is caused by the fact that the oxides on the C face are unstable,and easier to be removed with molten alkali,rather than the C face being easier to be oxidized.展开更多
Zinc-ion batteries(ZIBs)are considered to be one of the most promising candidates to replace lithium-ion batteries(LIBs)due to the high theoretical capacity,low cost and intrinsic safety.However,zinc dendrites,hydroge...Zinc-ion batteries(ZIBs)are considered to be one of the most promising candidates to replace lithium-ion batteries(LIBs)due to the high theoretical capacity,low cost and intrinsic safety.However,zinc dendrites,hydrogen evolution reaction,surface passivation and other side reactions will inevitably occur during the charging and discharging process of Zn anode,which will seriously affect the cycle stability of the battery and hinder its practical application.The etching strategy of Zn anode has attracted wide attention because of its simple operation and broad commercial prospects,and the etched Zn anode can effectively improve its electrochemical performance.However,there is no comprehensive review of the etching strategy of Zn anode.This review first summarizes the challenges faced by Zn anode,then puts forward the etching mechanisms and properties of acid,salt and other etchants.Finally,based on the above discussion,the challenges and opportunities of Zn anode etching strategy are proposed.展开更多
We described a method for obtaining fluorine-free Ti_(3)C_(2)Cl_(2)MXene phases by melting copper in CuCl_(2)instead of aluminum in Ti_(3)AlC_(2).XRD results show that when molten salt CuCl_(2)etches Ti_(3)AlC_(2),it ...We described a method for obtaining fluorine-free Ti_(3)C_(2)Cl_(2)MXene phases by melting copper in CuCl_(2)instead of aluminum in Ti_(3)AlC_(2).XRD results show that when molten salt CuCl_(2)etches Ti_(3)AlC_(2),it forms an intermediate product Ti_(3)CuC_(2),and then reacts with Ti_(3)CuC_(2)to obtain Ti_(3)C_(2)Cl_(2).The reaction of Ti_(3)AlC_(2)and CuCl_(2)at a temperature of 800℃for 2 h to obtain Ti_(3)C_(2)Cl_(2)with an optimal lamellar structure is shown in SEM results.The pseudopotential plane-wave(PP-PW)method is used to calculate on the electronic structure.The etching mechanism is investigated by the total energies of each substance.The chemical reaction of Ti_(3)AlC_(2)and CuCl_(2)will first become Ti_(3)CuC_(2)and Cu,and then become Ti_(3)C_(2)Cl_(2)during the Lewis acid etching process,which are consistent with the experimental results.展开更多
Quartz crystals are the most widely used material in resonant sensors,owing to their excellent piezoelectric and mechanical properties.With the development of portable and wearable devices,higher processing efficiency...Quartz crystals are the most widely used material in resonant sensors,owing to their excellent piezoelectric and mechanical properties.With the development of portable and wearable devices,higher processing efficiency and geometrical precision are required.Wet etching has been proven to be the most efficient etching method for large-scale production of quartz devices,and many wet etching approaches have been developed over the years.However,until now,there has been no systematic review of quartz crystal etching in liquid phase environments.Therefore,this article provides a comprehensive review of the development of wet etching processes and the achievements of the latest research in thisfield,covering conventional wet etching,additive etching,laser-induced backside wet etching,electrochemical etching,and electrochemical discharge machining.For each technique,a brief overview of its characteristics is provided,associated problems are described,and possible solutions are discussed.This review should provide an essential reference and guidance for the future development of processing strategies for the manufacture of quartz crystal devices.展开更多
Due to the increasing applications in optical devices electronics and nanosensors[1], 1D nanomaterials are becoming the extensive research area of physics, chemistry, medical, electronics and biology. As a member of 1...Due to the increasing applications in optical devices electronics and nanosensors[1], 1D nanomaterials are becoming the extensive research area of physics, chemistry, medical, electronics and biology. As a member of 1D nanostructured materials, the multilayer nanowires exhibit special properties and have strong potential applications in the fields of optoelectronic devices and nanosensors [2].展开更多
Biomass-H_(2)O gasification is a complex thermochemical reaction,including three processes of volatile removal:homogeneous/heterogeneous reforming,biochar gasification and etching.The rate-determining step is biochar-...Biomass-H_(2)O gasification is a complex thermochemical reaction,including three processes of volatile removal:homogeneous/heterogeneous reforming,biochar gasification and etching.The rate-determining step is biochar-H_(2)O gasification and etching so the DFT is carried out to see the catalytic role of different metal elements(K/Ni)in the zigzag biochar model.The calculation results show that the gasification of biochar-H_(2)O needs to go through four processes:dissociative adsorption of water,hydrogen transfer(hydrogen desorption,hydrogen atom transfer),carbon dissolution and CO desorption.The energy barrier indicated that the most significant step in reducing the activation energy of K is reflected in the hydrogen transfer step,which is reduced from 374.14 kJ/mol to 152.41 kJ/mol;the catalytic effect of Ni is mainly reflected in the carbon dissolution step,which is reduced from 122.34 kJ/mol to 84.8 kJ/mol.The existence of K causes the edge to have a stronger attraction to H and does not destroy theπbonds of biochar molecules.The destruction ofπbonds is mainly due to the role of H free radicals,while the destruction ofπbonds will lead to easier C-C bond rupture.Ni shows a strong attraction to O in OH,which forms strong Ni-O chemical bonds.Ni can also destroy the aromatic structure directly,making the gasification easier to happen.This study explored the catalytic mechanism of K/Ni on the biochar-H_(2)O gasification at the molecular level and looked forward to the potential synergy of K/Ni,laying a foundation for experimental research and catalyst design.展开更多
After electrolytically etched pattern graining surface of aluminum alloy, it is shows that there are porous oxide film containing α Al 2O 3 and α Al 2O 3 by means of SEM XRD and XPS analysis. In the ditches, a...After electrolytically etched pattern graining surface of aluminum alloy, it is shows that there are porous oxide film containing α Al 2O 3 and α Al 2O 3 by means of SEM XRD and XPS analysis. In the ditches, anodic oxidation makes pore density and diameter larger than other areas, and causes more coloring metal depositing and mutual cross linking. The electrolytically etched pattern surface shows relative deeper color on the ditches and lighter color on other areas, so it can be used for decoration. Electrolytic coloring metal exists in forms of Ag colloid and Ag 2O. Both anodic oxidation and electrolytic coloring affect the surface microstructure of aluminum alloy.展开更多
Discrimination of dislocations is critical to the statistics of dislocation densities in 4H silicon carbide(4H-SiC),which are routinely used to evaluate the quality of 4H-SiC single crystals and homoepitaxial layers.I...Discrimination of dislocations is critical to the statistics of dislocation densities in 4H silicon carbide(4H-SiC),which are routinely used to evaluate the quality of 4H-SiC single crystals and homoepitaxial layers.In this work,we show that the inclination angles of the etch pits of molten-alkali etched 4H-SiC can be adopted to discriminate threading screw dislocations(TSDs),threading edge dislocations(TEDs)and basal plane dislocations(BPDs)in 4H-SiC.In n-type 4H-SiC,the inclination angles of the etch pits of TSDs,TEDs and BPDs in molten-alkali etched 4H-SiC are in the ranges of 27°−35°,8°−15°and 2°−4°,respectively.In semi-insulating 4H-SiC,the inclination angles of the etch pits of TSDs and TEDs are in the ranges of 31°−34°and 21°−24°,respectively.The inclination angles of dislocation-related etch pits are independent of the etching duration,which facilitates the discrimination and statistic of dislocations in 4H-SiC.More significantly,the inclination angle of a threading mixed dislocations(TMDs)is found to consist of characteristic angles of both TEDs and TSDs.This enables to distinguish TMDs from TSDs in 4H-SiC.展开更多
The limiting length of tunnels, llim, of Al foil electro-etched in HCl-H2SO4 solution and the corresponding anodic polarization curves in the same solution were measured. It is found that there is a dependence of llim...The limiting length of tunnels, llim, of Al foil electro-etched in HCl-H2SO4 solution and the corresponding anodic polarization curves in the same solution were measured. It is found that there is a dependence of llim on the potential difference, △φ, between the pitting potential, φpit, and the corrosion potential, φcorr, of Al foil, when the temperature and H2SO4 concentration of HCl-H2SO4 electrolyte are changed. The dynamic equation on the tunnel growing and the linear equation between llim and △φ were deduced by analyzing the relationship among the over-potential on Al foil surface, the transport over-potential in tunnel solution and the over-potential at tunnel tip during the electro-etching. The results show that the growing velocity of tunnels decreases with their extending in length and the changing trend of llim can be judged by measuring △φ, which supplies a convenient access to explore new kinds of etchants.展开更多
Since the discovery in 2011,MXenes have become the rising star in the field of two-dimensional materials.Benefiting from the metallic-level conductivity,large and adjustable gallery spacing,low ion diffusion barrier,r...Since the discovery in 2011,MXenes have become the rising star in the field of two-dimensional materials.Benefiting from the metallic-level conductivity,large and adjustable gallery spacing,low ion diffusion barrier,rich surface chemistry,superior mechanical strength,MXenes exhibit great application prospects in energy storage and conversion,sensors,optoelectronics,electromagnetic interference shielding and biomedicine.Nevertheless,two issues seriously deteriorate the further development of MXenes.One is the high experimental risk of common preparation methods such as HF etching,and the other is the difficulty in obtaining MXenes with controllable surface groups.Recently,Lewis acidic etching,as a brand-new preparation strategy for MXenes,has attracted intensive attention due to its high safety and the ability to endow MXenes with uniform terminations.However,a comprehensive review of Lewis acidic etching method has not been reported yet.Herein,we first introduce the Lewis acidic etching from the following four aspects:etching mechanism,terminations regulation,in-situ formed metals and delamination of multi-layered MXenes.Further,the applications of MXenes and MXene-based hybrids obtained by Lewis acidic etching route in energy storage and conversion,sensors and microwave absorption are carefully summarized.Finally,some challenges and opportunities of Lewis acidic etching strategy are also presented.展开更多
Rational reconstruction of oxygen evolution reaction(OER)precatalysts and performance index of OER catalysts are crucial but still challenging for universal water electrolysis.Herein,we develop a double-cation etching...Rational reconstruction of oxygen evolution reaction(OER)precatalysts and performance index of OER catalysts are crucial but still challenging for universal water electrolysis.Herein,we develop a double-cation etching strategy to tailor the electronic structure of NiMoO_(4),where the prepared NiMoO_(4) nanorods etched by H_(2)O_(2) reconstruct their surface with abundant cation deficiencies and lattice distortion.Calculation results reveal that the double cation deficiencies can make the upshift of d-band center for Ni atoms and the active sites with better oxygen adsorption capacity.As a result,the optimized sample(NMO-30M)possesses an overpotential of 260 mV at 10 mA cm−2 and excellent long-term durability of 162 h.Importantly,in situ Raman test reveals the rapid formation of high-oxidation-state transition metal hydroxide species,which can further help to improve the catalytic activity of NiMoO_(4) in OER.This work highlights the influence of surface remodification and shed some light on activating catalysts.展开更多
Photoresist grating was fabricated by holography, and it was used in the mask of ion etching. The groovy depth of the etched glass grating was 1.6μm. The glass waveguide was formed by K^+/Na^+ ion exchanging. The las...Photoresist grating was fabricated by holography, and it was used in the mask of ion etching. The groovy depth of the etched glass grating was 1.6μm. The glass waveguide was formed by K^+/Na^+ ion exchanging. The laser beam of 633nm was coupled in the waveguide by a prism at one end, then, it passed through the grating and came out of the waveguide at other end. In the experiment, the Bragg diffraction with several orders was observed. The first order Bragg diffraction had the highest efficiency of 90 percent.展开更多
In the past few decades,inspired by the superhydrophobic surfaces(SHPS)of animals and plants such as lotus leaves,rose petals,legs of water striders,and wings of butterflies,preparing metal materials with metallic SHP...In the past few decades,inspired by the superhydrophobic surfaces(SHPS)of animals and plants such as lotus leaves,rose petals,legs of water striders,and wings of butterflies,preparing metal materials with metallic SHPS(MSHPS)have attracted great research interest,due to the great prospect in practical applications.To obtain SHPS on conventional metal materials,it is necessary to construct rough surface,followed by modification with low surface energy substances.In this paper,the action mechanism and the current research status of MSHPS were reviewed through the following aspects.Firstly,the model of wetting theory was presented,and then the progress in MSHPS preparation through chemical etching method was discussed.Secondly,the applications of MSHPS in self-cleaning,anti-icing,corrosion resistance,drag reduction,oil-water separation,and other aspects were introduced.Finally,the challenges encountered in the present application of MSHPS were summarized,and the future research interests were discussed.展开更多
Introduction of titanium oxides with high permittivity on etched aluminum foils’ surface has been successfully utilized to increase specific capacitance of anode foils for aluminum electrolytic capacitors. In order t...Introduction of titanium oxides with high permittivity on etched aluminum foils’ surface has been successfully utilized to increase specific capacitance of anode foils for aluminum electrolytic capacitors. In order to quantify the concentration of titanium (IV) on the etched aluminum foil precisely, a simple and rapid spectrophotometric procedure has been developed. After optimizing a series of variables including absorbance wavelength, concentration of nitric acid, concentration of hydrogen peroxide, nitration time and developing time, analytical precision and accuracy were tested by using standard working solution containing known amount of titanium (IV). The results showed that Lambert-Beer’s law was obeyed in the range of 0.01 to 3.00 mmol·L﹣1. The relative standard deviation (RSD) ranged from 0.67% to 1.09% (n = 6), and the recovery was between 99.17% - 100.03%. Investigation on effect of Al3+ ion indicated that there was no interference in the absorbance of titanium (IV) at 410 nm. The proposed procedure was applied to real samples for the determination of titanium (IV), and the results were in a good agreement with the values certified by inductively coupled plasma-atomic emission spectrometry (ICP-AES).展开更多
In order to obtain high-quality spherical RDX crystal particles,the RDX crystals were suspended in a mixed solvent of cyclohexanone and cyclohexane,subsequently a solvent etching study was carried out under the action...In order to obtain high-quality spherical RDX crystal particles,the RDX crystals were suspended in a mixed solvent of cyclohexanone and cyclohexane,subsequently a solvent etching study was carried out under the action of vibration/acoustic flow coupled flow field,which generated by resonance acoustic mixing.The effects of solvent ratio,temperature,acceleration and experiment time on morphology as well as particle size of RDX crystals were studied.Not only were the morphology,particle size distribution and crystal form of RDX crystals determined,but also the thermal decomposition performance and mechanical sensitivity of spherical RDX were examined and discussed.Results indicated that under the process of solvent/non-solvent volume ratio at 1:2,temperature of 40℃,acceleration of 40 g and experiment time of 4 h,α-type RDX crystal with sphericity of 0.92 can be obtained.Furthermore,the median particle size(D_(50))of spherical RDX crystals is 215.8 μm with a unimodal particle size distribution(size span 1.34).For one thing,the thermal decomposition peak temperature of spherical RDX is about 2.5℃ higher than that of raw RDX,and apparent activation energy reaches 444.68 kJ/mol.For another thing,impact sensitivity and friction sensitivity of spherical RDX are 18.18% and 33.33% lower than that of raw RDX,respectively.It demonstrates that safety of spherical RDX under thermal,impact and friction stimuli has been improved.展开更多
2D MXene(Ti_(3)CNT_(x))has been considered as the most promising electrode material for flexible supercapacitors owing to its metallic conductivity,ultra-high capacitance,and excellent flexibility.However,it suffers f...2D MXene(Ti_(3)CNT_(x))has been considered as the most promising electrode material for flexible supercapacitors owing to its metallic conductivity,ultra-high capacitance,and excellent flexibility.However,it suffers from a severe restacking problem during the electrode fabrication process,limiting the ion transport kinetics and the accessibility of ions in the electrodes,especially in the direction normal to the electrode surface.Herein,we report a NH_(3)-induced in situ etching strategy to fabricate 3D-interconnected porous MXene/carbon dots(p-MC)films for high-performance flexible supercapacitor.The pre-intercalated carbon dots(CDs)first prevent the restacking of MXene to expose more inner electrochemical active sites.The partially decomposed CDs generate NH_(3)for in situ etching of MXene nanosheets toward 3D-interconnected p-MC films.Benefiting from the structural merits and the 3D-interconnected ionic transmission channels,p-MC film electrodes achieve excellent gravimetric capacitance(688.9 F g^(-1)at 2 A g^(-1))and superior rate capability.Moreover,the optimized p-MC electrode is assembled into an asymmetric solid-state flexible supercapacitor with high energy density and superior cycling stability,demonstrating the great promise of p-MC electrode for practical applications.展开更多
Nanopores and nanochannels produced by etching heavy ion tracks are widely used in contemporary science and technology[1]. Conical and doubly-conical nanopores (channels) have attracted special interest in the past de...Nanopores and nanochannels produced by etching heavy ion tracks are widely used in contemporary science and technology[1]. Conical and doubly-conical nanopores (channels) have attracted special interest in the past decade due to their potential in modern and rapidly growing fields, including molecular sensors, logic gates, nanoactuators, and other nanofluidic devices[2;3].展开更多
Semiconductor nuclear radiation detectors made from tertiary and quaternary compounds of cadmium telluride (CdTe) can operate at room temperature without cryogenic cooling. One of such materials that have become of gr...Semiconductor nuclear radiation detectors made from tertiary and quaternary compounds of cadmium telluride (CdTe) can operate at room temperature without cryogenic cooling. One of such materials that have become of great interest is cadmium zinc telluride selenide (CdZnTeSe). Compared to other CdTe-based materials, such as cadmium zinc telluride (CdZnTe), CdZnTeSe can be grown with much less Te inclusions and sub-grain boundary networks. Chemical etching is often used to smoothen wafer surfaces during detector fabrication. This paper presents the characterization of CdZnTeSe that is chemically etched using bromine methanol solution. Infrared imaging shows that the wafer has no sub-grain boundary networks that often limit detector performance. The current-voltage (I-V) characterization experiment gave a resistivity of 4.6 × 10<sup>10</sup> Ω-cm for the sample. The I-V curve was linear in the ±10 to ±50 volts range. An energy resolution of 7.2% was recorded at 100 V for the 59.6-keV gamma line of <sup>241</sup>Am.展开更多
基金supported in part by the National Natural Science Foundation of China (Grant Nos.62074050 and 61975051)Research Fund by State Key Laboratory of Reliability and Intelligence of Electrical Equipment,Hebei University of Technology (Grant Nos.EERI PI2020008 and EERI_PD2021012)Joint Research Project for Tunghsu Group and Hebei University of Technology (Grant No.HI1909)。
文摘A low hole injection efficiency for InGaN/GaN micro-light-emitting diodes(μLEDs) has become one of the main bottlenecks affecting the improvement of the external quantum efficiency(EQE) and the optical power. In this work, we propose and fabricate a polarization mismatched p-GaN/p-Al_(0.25)Ga_(0.75)N/p-GaN structure for 445 nm GaN-based μLEDs with the size of 40 × 40 μm^(2), which serves as the hole injection layer. The polarization-induced electric field in the p-GaN/p-Al_(0.25)Ga_(0.75)N/p-GaN structure provides holes with more energy and can facilitate the non-equilibrium holes to transport into the active region for radiative recombination. Meanwhile, a secondary etched mesa for μLEDs is also designed, which can effectively keep the holes apart from the defected region of the mesa sidewalls, and the surface nonradiative recombination can be suppressed. Therefore, the proposed μLED with the secondary etched mesa and the p-GaN/p-Al_(0.25)Ga_(0.75)N/p-GaN structure has the enhanced EQE and the improved optical power density when compared with the μLED without such designs.
基金financially supported by the Scientific and Technology Project of State Grid Corporation of China,Research on Dry Etching Forming Technology of Silicon Carbide Device,Project No.5500-202158437A-0-0-00.
文摘The comparison of domestic and foreign studies has been utilized to extensively employ junction termination extension(JTE)structures for power devices.However,achieving a gradual doping concentration change in the lateral direction is difficult for SiC devices since the diffusion constants of the implanted aluminum ions in SiC are much less than silicon.Many previously reported studies adopted many new structures to solve this problem.Additionally,the JTE structure is strongly sensitive to the ion implantation dose.Thus,GA-JTE,double-zone etched JTE structures,and SM-JTE with modulation spacing were reported to overcome the above shortcomings of the JTE structure and effectively increase the breakdown voltage.They provided a theoretical basis for fabricating terminal structures of 4H-SiC PiN diodes.This paper summarized the effects of different terminal structures on the electrical properties of SiC devices at home and abroad.Presently,the continuous development and breakthrough of terminal technology have significantly improved the breakdown voltage and terminal efficiency of 4H-SiC PiN power diodes.
基金This work is supported by the Natural Science Foundation of China(Grant Nos.62274143&62204216)Joint Funds of the Zhejiang Provincial Natural Science Foundation of China(Grant Nos.LHZSD24E020001)+4 种基金the“Pioneer”and“Leading Goose”R&D Program of Zhejiang(Grant Nos.2022C0102&2023C01010)Partial support was provided by the Leading Innovative and Entrepreneur Team Introduction Program of Hangzhou(Grant No.TD2022012)Fundamental Research Funds for the Central Universities(Grant No.226-2022-00200)the Natural Science Foundation of China for Innovative Research Groups(Grant No.61721005)the Open Fund of Zhejiang Provincial Key Laboratory of Wide Bandgap Semiconductors,Hangzhou Global Scientific and Technological Innovation Center,Zhejiang University.
文摘Molten-alkali etching has been widely used to reveal dislocations in 4H silicon carbide(4H-SiC),which has promoted the identification and statistics of dislocation density in 4H-SiC single crystals.However,the etching mechanism of 4H-SiC is limited misunderstood.In this letter,we reveal the anisotropic etching mechanism of the Si face and C face of 4H-SiC by combining molten-KOH etching,X-ray photoelectron spectroscopy(XPS)and first-principles investigations.The activation energies for the molten-KOH etching of the C face and Si face of 4H-SiC are calculated to be 25.09 and 35.75 kcal/mol,respectively.The molten-KOH etching rate of the C face is higher than the Si face.Combining XPS analysis and first-principles calculations,we find that the molten-KOH etching of 4H-SiC is proceeded by the cycling of the oxidation of 4H-SiC by the dissolved oxygen and the removal of oxides by molten KOH.The faster etching rate of the C face is caused by the fact that the oxides on the C face are unstable,and easier to be removed with molten alkali,rather than the C face being easier to be oxidized.
基金supported by the Science and Technology Research Project of the Education Department of Jilin Province (JJKH20230803KJ)。
文摘Zinc-ion batteries(ZIBs)are considered to be one of the most promising candidates to replace lithium-ion batteries(LIBs)due to the high theoretical capacity,low cost and intrinsic safety.However,zinc dendrites,hydrogen evolution reaction,surface passivation and other side reactions will inevitably occur during the charging and discharging process of Zn anode,which will seriously affect the cycle stability of the battery and hinder its practical application.The etching strategy of Zn anode has attracted wide attention because of its simple operation and broad commercial prospects,and the etched Zn anode can effectively improve its electrochemical performance.However,there is no comprehensive review of the etching strategy of Zn anode.This review first summarizes the challenges faced by Zn anode,then puts forward the etching mechanisms and properties of acid,salt and other etchants.Finally,based on the above discussion,the challenges and opportunities of Zn anode etching strategy are proposed.
基金Funded by the National Natural Science Foundation for Young Scholars of China(No.51302073)the Hubei Provincial Key Laboratory of Green Materials for Light IndustryHubei University of Technology(No.202307B07)。
文摘We described a method for obtaining fluorine-free Ti_(3)C_(2)Cl_(2)MXene phases by melting copper in CuCl_(2)instead of aluminum in Ti_(3)AlC_(2).XRD results show that when molten salt CuCl_(2)etches Ti_(3)AlC_(2),it forms an intermediate product Ti_(3)CuC_(2),and then reacts with Ti_(3)CuC_(2)to obtain Ti_(3)C_(2)Cl_(2).The reaction of Ti_(3)AlC_(2)and CuCl_(2)at a temperature of 800℃for 2 h to obtain Ti_(3)C_(2)Cl_(2)with an optimal lamellar structure is shown in SEM results.The pseudopotential plane-wave(PP-PW)method is used to calculate on the electronic structure.The etching mechanism is investigated by the total energies of each substance.The chemical reaction of Ti_(3)AlC_(2)and CuCl_(2)will first become Ti_(3)CuC_(2)and Cu,and then become Ti_(3)C_(2)Cl_(2)during the Lewis acid etching process,which are consistent with the experimental results.
基金supported by the Natural Science Foundation of China (Grant No.12234005)the major research and development program of Jiangsu Province (Grant Nos.BE2021007-2 and BK20222007)。
文摘Quartz crystals are the most widely used material in resonant sensors,owing to their excellent piezoelectric and mechanical properties.With the development of portable and wearable devices,higher processing efficiency and geometrical precision are required.Wet etching has been proven to be the most efficient etching method for large-scale production of quartz devices,and many wet etching approaches have been developed over the years.However,until now,there has been no systematic review of quartz crystal etching in liquid phase environments.Therefore,this article provides a comprehensive review of the development of wet etching processes and the achievements of the latest research in thisfield,covering conventional wet etching,additive etching,laser-induced backside wet etching,electrochemical etching,and electrochemical discharge machining.For each technique,a brief overview of its characteristics is provided,associated problems are described,and possible solutions are discussed.This review should provide an essential reference and guidance for the future development of processing strategies for the manufacture of quartz crystal devices.
文摘Due to the increasing applications in optical devices electronics and nanosensors[1], 1D nanomaterials are becoming the extensive research area of physics, chemistry, medical, electronics and biology. As a member of 1D nanostructured materials, the multilayer nanowires exhibit special properties and have strong potential applications in the fields of optoelectronic devices and nanosensors [2].
基金Sponsored by the National Natural Science Foundation of China(Grant No.52276180)the Natural Science Foundation of Heilongjiang Province(Grant No.YQ2022E026).
文摘Biomass-H_(2)O gasification is a complex thermochemical reaction,including three processes of volatile removal:homogeneous/heterogeneous reforming,biochar gasification and etching.The rate-determining step is biochar-H_(2)O gasification and etching so the DFT is carried out to see the catalytic role of different metal elements(K/Ni)in the zigzag biochar model.The calculation results show that the gasification of biochar-H_(2)O needs to go through four processes:dissociative adsorption of water,hydrogen transfer(hydrogen desorption,hydrogen atom transfer),carbon dissolution and CO desorption.The energy barrier indicated that the most significant step in reducing the activation energy of K is reflected in the hydrogen transfer step,which is reduced from 374.14 kJ/mol to 152.41 kJ/mol;the catalytic effect of Ni is mainly reflected in the carbon dissolution step,which is reduced from 122.34 kJ/mol to 84.8 kJ/mol.The existence of K causes the edge to have a stronger attraction to H and does not destroy theπbonds of biochar molecules.The destruction ofπbonds is mainly due to the role of H free radicals,while the destruction ofπbonds will lead to easier C-C bond rupture.Ni shows a strong attraction to O in OH,which forms strong Ni-O chemical bonds.Ni can also destroy the aromatic structure directly,making the gasification easier to happen.This study explored the catalytic mechanism of K/Ni on the biochar-H_(2)O gasification at the molecular level and looked forward to the potential synergy of K/Ni,laying a foundation for experimental research and catalyst design.
文摘After electrolytically etched pattern graining surface of aluminum alloy, it is shows that there are porous oxide film containing α Al 2O 3 and α Al 2O 3 by means of SEM XRD and XPS analysis. In the ditches, anodic oxidation makes pore density and diameter larger than other areas, and causes more coloring metal depositing and mutual cross linking. The electrolytically etched pattern surface shows relative deeper color on the ditches and lighter color on other areas, so it can be used for decoration. Electrolytic coloring metal exists in forms of Ag colloid and Ag 2O. Both anodic oxidation and electrolytic coloring affect the surface microstructure of aluminum alloy.
基金supported by“Pioneer”and“Leading Goose”R&D Program of Zhejiang(Grant No.2022C01021)National Key Research and Development Program of China(Grant Nos.2018YFB2200101)+3 种基金Natural Science Foundation of China(Grant Nos.61774133)Fundamental Research Funds for the Central Universities(Grant No.2018XZZX003-02)Natural Science Foundation of China for Innovative Research Groups(Grant No.61721005)Zhejiang University Education Foundation Global Partnership Fund.
文摘Discrimination of dislocations is critical to the statistics of dislocation densities in 4H silicon carbide(4H-SiC),which are routinely used to evaluate the quality of 4H-SiC single crystals and homoepitaxial layers.In this work,we show that the inclination angles of the etch pits of molten-alkali etched 4H-SiC can be adopted to discriminate threading screw dislocations(TSDs),threading edge dislocations(TEDs)and basal plane dislocations(BPDs)in 4H-SiC.In n-type 4H-SiC,the inclination angles of the etch pits of TSDs,TEDs and BPDs in molten-alkali etched 4H-SiC are in the ranges of 27°−35°,8°−15°and 2°−4°,respectively.In semi-insulating 4H-SiC,the inclination angles of the etch pits of TSDs and TEDs are in the ranges of 31°−34°and 21°−24°,respectively.The inclination angles of dislocation-related etch pits are independent of the etching duration,which facilitates the discrimination and statistic of dislocations in 4H-SiC.More significantly,the inclination angle of a threading mixed dislocations(TMDs)is found to consist of characteristic angles of both TEDs and TSDs.This enables to distinguish TMDs from TSDs in 4H-SiC.
基金Project supported by University New Materials Disciplines Construction Program of Beijing, China
文摘The limiting length of tunnels, llim, of Al foil electro-etched in HCl-H2SO4 solution and the corresponding anodic polarization curves in the same solution were measured. It is found that there is a dependence of llim on the potential difference, △φ, between the pitting potential, φpit, and the corrosion potential, φcorr, of Al foil, when the temperature and H2SO4 concentration of HCl-H2SO4 electrolyte are changed. The dynamic equation on the tunnel growing and the linear equation between llim and △φ were deduced by analyzing the relationship among the over-potential on Al foil surface, the transport over-potential in tunnel solution and the over-potential at tunnel tip during the electro-etching. The results show that the growing velocity of tunnels decreases with their extending in length and the changing trend of llim can be judged by measuring △φ, which supplies a convenient access to explore new kinds of etchants.
基金supported by the Highstar Corporation HSD20210118Taihu Electric Corporation 0001。
文摘Since the discovery in 2011,MXenes have become the rising star in the field of two-dimensional materials.Benefiting from the metallic-level conductivity,large and adjustable gallery spacing,low ion diffusion barrier,rich surface chemistry,superior mechanical strength,MXenes exhibit great application prospects in energy storage and conversion,sensors,optoelectronics,electromagnetic interference shielding and biomedicine.Nevertheless,two issues seriously deteriorate the further development of MXenes.One is the high experimental risk of common preparation methods such as HF etching,and the other is the difficulty in obtaining MXenes with controllable surface groups.Recently,Lewis acidic etching,as a brand-new preparation strategy for MXenes,has attracted intensive attention due to its high safety and the ability to endow MXenes with uniform terminations.However,a comprehensive review of Lewis acidic etching method has not been reported yet.Herein,we first introduce the Lewis acidic etching from the following four aspects:etching mechanism,terminations regulation,in-situ formed metals and delamination of multi-layered MXenes.Further,the applications of MXenes and MXene-based hybrids obtained by Lewis acidic etching route in energy storage and conversion,sensors and microwave absorption are carefully summarized.Finally,some challenges and opportunities of Lewis acidic etching strategy are also presented.
基金supported by the National Natural Science Foundation of China(No.12004146)Natural Science Foundation of Gansu Province,China(Nos.20JR5RA303 and 20JR10RA648)the Fundamental Research Funds for the Central Universities(No.LZUMMM2022007).
文摘Rational reconstruction of oxygen evolution reaction(OER)precatalysts and performance index of OER catalysts are crucial but still challenging for universal water electrolysis.Herein,we develop a double-cation etching strategy to tailor the electronic structure of NiMoO_(4),where the prepared NiMoO_(4) nanorods etched by H_(2)O_(2) reconstruct their surface with abundant cation deficiencies and lattice distortion.Calculation results reveal that the double cation deficiencies can make the upshift of d-band center for Ni atoms and the active sites with better oxygen adsorption capacity.As a result,the optimized sample(NMO-30M)possesses an overpotential of 260 mV at 10 mA cm−2 and excellent long-term durability of 162 h.Importantly,in situ Raman test reveals the rapid formation of high-oxidation-state transition metal hydroxide species,which can further help to improve the catalytic activity of NiMoO_(4) in OER.This work highlights the influence of surface remodification and shed some light on activating catalysts.
基金Academia Sinica and the Ministry of Posts and Telecommunications
文摘Photoresist grating was fabricated by holography, and it was used in the mask of ion etching. The groovy depth of the etched glass grating was 1.6μm. The glass waveguide was formed by K^+/Na^+ ion exchanging. The laser beam of 633nm was coupled in the waveguide by a prism at one end, then, it passed through the grating and came out of the waveguide at other end. In the experiment, the Bragg diffraction with several orders was observed. The first order Bragg diffraction had the highest efficiency of 90 percent.
基金the financial support of Shanghai Pujiang Program(22PJD001)the Scientific Research Project from Science and Technology Commission of Shanghai Municipality(19DZ1204903)the Fundamental Research Funds for the Central Universities(2232021G-11)。
文摘In the past few decades,inspired by the superhydrophobic surfaces(SHPS)of animals and plants such as lotus leaves,rose petals,legs of water striders,and wings of butterflies,preparing metal materials with metallic SHPS(MSHPS)have attracted great research interest,due to the great prospect in practical applications.To obtain SHPS on conventional metal materials,it is necessary to construct rough surface,followed by modification with low surface energy substances.In this paper,the action mechanism and the current research status of MSHPS were reviewed through the following aspects.Firstly,the model of wetting theory was presented,and then the progress in MSHPS preparation through chemical etching method was discussed.Secondly,the applications of MSHPS in self-cleaning,anti-icing,corrosion resistance,drag reduction,oil-water separation,and other aspects were introduced.Finally,the challenges encountered in the present application of MSHPS were summarized,and the future research interests were discussed.
文摘Introduction of titanium oxides with high permittivity on etched aluminum foils’ surface has been successfully utilized to increase specific capacitance of anode foils for aluminum electrolytic capacitors. In order to quantify the concentration of titanium (IV) on the etched aluminum foil precisely, a simple and rapid spectrophotometric procedure has been developed. After optimizing a series of variables including absorbance wavelength, concentration of nitric acid, concentration of hydrogen peroxide, nitration time and developing time, analytical precision and accuracy were tested by using standard working solution containing known amount of titanium (IV). The results showed that Lambert-Beer’s law was obeyed in the range of 0.01 to 3.00 mmol·L﹣1. The relative standard deviation (RSD) ranged from 0.67% to 1.09% (n = 6), and the recovery was between 99.17% - 100.03%. Investigation on effect of Al3+ ion indicated that there was no interference in the absorbance of titanium (IV) at 410 nm. The proposed procedure was applied to real samples for the determination of titanium (IV), and the results were in a good agreement with the values certified by inductively coupled plasma-atomic emission spectrometry (ICP-AES).
文摘In order to obtain high-quality spherical RDX crystal particles,the RDX crystals were suspended in a mixed solvent of cyclohexanone and cyclohexane,subsequently a solvent etching study was carried out under the action of vibration/acoustic flow coupled flow field,which generated by resonance acoustic mixing.The effects of solvent ratio,temperature,acceleration and experiment time on morphology as well as particle size of RDX crystals were studied.Not only were the morphology,particle size distribution and crystal form of RDX crystals determined,but also the thermal decomposition performance and mechanical sensitivity of spherical RDX were examined and discussed.Results indicated that under the process of solvent/non-solvent volume ratio at 1:2,temperature of 40℃,acceleration of 40 g and experiment time of 4 h,α-type RDX crystal with sphericity of 0.92 can be obtained.Furthermore,the median particle size(D_(50))of spherical RDX crystals is 215.8 μm with a unimodal particle size distribution(size span 1.34).For one thing,the thermal decomposition peak temperature of spherical RDX is about 2.5℃ higher than that of raw RDX,and apparent activation energy reaches 444.68 kJ/mol.For another thing,impact sensitivity and friction sensitivity of spherical RDX are 18.18% and 33.33% lower than that of raw RDX,respectively.It demonstrates that safety of spherical RDX under thermal,impact and friction stimuli has been improved.
基金The authors gratefully acknowledge financial support from the National Natural Science Foundation of China(Grant Nos.21805261 and 51972277)Sichuan Science and Technology Program(Grant Nos.2021YFG0251 and 2022YFG0293)Fundamental Research Funds for the Central Universities(Grant No.2682021CX105)。
文摘2D MXene(Ti_(3)CNT_(x))has been considered as the most promising electrode material for flexible supercapacitors owing to its metallic conductivity,ultra-high capacitance,and excellent flexibility.However,it suffers from a severe restacking problem during the electrode fabrication process,limiting the ion transport kinetics and the accessibility of ions in the electrodes,especially in the direction normal to the electrode surface.Herein,we report a NH_(3)-induced in situ etching strategy to fabricate 3D-interconnected porous MXene/carbon dots(p-MC)films for high-performance flexible supercapacitor.The pre-intercalated carbon dots(CDs)first prevent the restacking of MXene to expose more inner electrochemical active sites.The partially decomposed CDs generate NH_(3)for in situ etching of MXene nanosheets toward 3D-interconnected p-MC films.Benefiting from the structural merits and the 3D-interconnected ionic transmission channels,p-MC film electrodes achieve excellent gravimetric capacitance(688.9 F g^(-1)at 2 A g^(-1))and superior rate capability.Moreover,the optimized p-MC electrode is assembled into an asymmetric solid-state flexible supercapacitor with high energy density and superior cycling stability,demonstrating the great promise of p-MC electrode for practical applications.
文摘Nanopores and nanochannels produced by etching heavy ion tracks are widely used in contemporary science and technology[1]. Conical and doubly-conical nanopores (channels) have attracted special interest in the past decade due to their potential in modern and rapidly growing fields, including molecular sensors, logic gates, nanoactuators, and other nanofluidic devices[2;3].
文摘Semiconductor nuclear radiation detectors made from tertiary and quaternary compounds of cadmium telluride (CdTe) can operate at room temperature without cryogenic cooling. One of such materials that have become of great interest is cadmium zinc telluride selenide (CdZnTeSe). Compared to other CdTe-based materials, such as cadmium zinc telluride (CdZnTe), CdZnTeSe can be grown with much less Te inclusions and sub-grain boundary networks. Chemical etching is often used to smoothen wafer surfaces during detector fabrication. This paper presents the characterization of CdZnTeSe that is chemically etched using bromine methanol solution. Infrared imaging shows that the wafer has no sub-grain boundary networks that often limit detector performance. The current-voltage (I-V) characterization experiment gave a resistivity of 4.6 × 10<sup>10</sup> Ω-cm for the sample. The I-V curve was linear in the ±10 to ±50 volts range. An energy resolution of 7.2% was recorded at 100 V for the 59.6-keV gamma line of <sup>241</sup>Am.