Seismic Response Analysis of Steel Structure Isolation System Under Long-Period Seismic Motion

To analyze the seismic response of steel structure isolation systems under long-period seismic motion,a 9-story steel frame building was selected as the subject.Five steel structure finite element models were established using SAP2000.Response spectrum analysis was conducted on the seismic motion to determine if it adhered to the characteristics of long-period seismic motion.Modal analysis of each structural model revealed that the isolation structure significantly prolonged the structural natural vibration period and enhanced seismic performance.Base reactions and floor displacements of various structures notably increased under long-period seismic motion compared to regular seismic activity.Placing isolation bearings in the lower part of the structure proved more effective under long-period seismic motion.In seismic design engineering,it is essential to consider the impact of long-period seismic motion on structures and the potential failure of isolation bearings.

A new isolation device using shape memory alloy and its application for long-span structures

The key points to consider in determining the effectiveness of using structural isolation with shape memory alloys （SMA） are the constitutive model, the SMA isolation device and the analysis method. In this paper, a simplified constitutive model based on the classic theory of plasticity is proposed to simulate the behavior of the superelasticity of the SMA, in which the martensite volume fraction is considered as one of the state variables. Comparisons between simulation results and experimental results are made and indicate that the proposed constitutive model yields stress-strain curves that are in good agreement with the experimental ones. Thus, the proposed model can correctly simulate the yield mechanism and energy dissipation capacity of the SMA. Next, in order to make full use of the superelasticity of SMA, a new SMA isolator composed of pre-tensioned SMA bars is presented. Then, a finite element analytical model is established to simulate the behavior of the SMA isolator according to its configuration and simplified constitutive model. Finally, a simplified design method for long-span structures installed with SMA isolators is proposed, which is further used to investigate the isolation effects of a space grid structure. Results show that the SMA isolator can reduce the seismic responses of the structure effectively, which indicates the effectiveness of the proposed SMA isolation method.

ISOLATION AND STRUCTURES OF FOUR CYCLODIPEPTIDES

Three novel interesting polychlorinated cyclodipeptides,designated dyssmide A(1),B(2),C(3)and a known compound,2,3-dihydrodyeamide C(4)were isolated from the sponge Dysidea sp.Their structures were elucidated by spectroscopic methods.

High-Throughput Growth of Hexagonal Boron Nitride Film Using Porous-Structure Isolation Layer

Chemical vapor deposition is considered as the most hopeful method for the synthesis of large-area high-quality hexagonal boron nitride on the substrate of catalytic metal. However, the size the hexagonal boron nitride films are limited to the size of growth chamber, which indicates a lower production efficiency. In this paper, the utilization efficiency of growth chamber is highly improved by alternately stacking multiple pieces of Cu foils and carbon fiber surface felt with porous structure. Uniform and continuous hexagonal boron nitride films are prepared on Cu foils through chemical vapor deposition utilizing ammonia borane as the precursor. This work develops a simple and practicable method for high-throughput preparation of hexagonal boron nitride films, which could contribute to the industrial application of hexagonal boron nitride. .

Seismic response of a mid-story isolated structure considering SSI in mountainous areas under long-period earthquakes

At present,there is not much research on mid-story isolated structures in mountainous areas.In this study,a model of a mid-story isolated structure considering soil-structure interaction(SSI)in mountainous areas is established along with a model that does not consider SSI.Eight long-period earthquake waves and two ordinary earthquake waves are selected as inputs for the dynamic time history analysis of the structure.The results show that the seismic response of a mid-story isolated structure considering SSI in mountainous areas can be amplified when compared with a structure that does not consider SSI.The structure response under long-period earthquakes is larger than that of ordinary earthquakes.The structure response under far-field harmonic-like earthquakes is larger than that of near-fault pulse-type earthquakes.The structure response under near-fault pulse-type earthquakes is larger than that of far-field non-harmonic earthquakes.When subjected to long-period earthquakes,the displacement of the isolated bearings exceeded the limit value,which led to instability and overturning of the structure.The structure with dampers in the isolated story could adequately control the nonlinear response of the structure,effectively reduce the displacement of the isolated bearings,and provide a convenient,efficient and economic method not only for new construction but also to retrofit existing structures.

A Novel Radiation Tolerant SOI Isolation Structure

A novel radiation tolerant SOI isolation structure,consisting of thin SiO2/polysilicon/field SiO2 multilayers,is proposed. A device with this structure does not show obvious changes in subthreshold characteristics and leakage current,indicating a superior radiation tolerance to traditional LOCOS.

Study on the Influence of Aspect Ratio on the Seismic Response and Overturning Resistance of a New Staggered Story Isolated Structure

The aspect ratio of the structure has a significant impact on the overall stability of the ultra high-rise building. A large aspect ratio of the structure increases the risk of overturning and reduces the lateral stiffness of the structure, leading to significant tensile and compressive stresses in the isolated bearings. To study the effect of aspect ratio on the seismic response and overturning resistance of a new staggered story isolated structure, three models with different aspect ratios were established. Nonlinear time-history analysis of the three models was conducted using ETABS finite element software. The results indicate that the overturning moment and overturning resistance moment of the superstructure in the new staggered story isolated structure increase with an increasing aspect ratio. However, the increase in the overturning moment of the superstructure is much greater than the increase in the overturning resistance moment, resulting in a decrease in the overturning resistance ratio of the superstructure with an increasing aspect ratio. The overturning moment and overturning resistance moment of the substructure in the new staggered story isolated structure decrease with an increasing aspect ratio. However, the decrease in the overturning moment of the substructure is greater than the decrease in the overturning resistance moment, leading to an increase in the overturning resistance ratio of the substructure with an increasing aspect ratio. The decrease in the overturning resistance ratio of the superstructure in the new staggered story isolated structure is much greater than the increase in the overturning resistance ratio of the substructure. Therefore, as the aspect ratio of the overall structure increases, the overturning resistance ratio of the superstructure and the entire structure decreases.

Optimal design and effectiveness evaluation for inerter-based devices on mitigating seismic responses of base isolated structures

The optimal design and effectiveness of three control systems,tuned viscous mass damper(TVMD),tuned inerter damper(TID)and tuned mass damper(TMD),on mitigating the seismic responses of base isolated structures,were systematically studied.First,the seismic responses of the base isolated structure with each control system under white noise excitation were obtained.Then,the structural parameter optimizations of the TVMD,TID and TMD were conducted by using three different objectives.The results show that the three control systems were all effective in minimizing the root mean square value of seismic responses,including the base shear of the BIS,the absolute acceleration of structural SDOF,and the relative displacement between the base isolation floor and the foundation.Finally,considering the superstructure as a structural MDOF,a series of time history analyses were performed to investigate the effectiveness and activation sensitivity of the three control systems under far field and near fault seismic excitations.The results show that the effectiveness of TID and TMD with optimized parameters on mitigating the seismic responses of base isolated structures increased as the mass ratio increases,and the effectiveness of TID was always better than TMD with the same mass ratio.The TVMD with a lower mass ratio was more efficient in reducing the seismic response than the TID and TMD.Furthermore,the TVMD,when compared with TMD and TID,had better activation sensitivity and a smaller stroke.

Shaking Table Model Test of Isolated Structure on Soft Site and Analysis on Its Isolation Efficiency

Adopting a soft site model built on soft interlayer soil foundation,a shaking table test for soft interlayer soil-isolated structure interaction is conducted to investigate the seismic response of isolated structure on soft site,and analyze its isolation effect.Test results show that the test can reflect the earthquake response characteristics of isolated structure on soft site.It is on soft site that the dynamic characteristics of isolated structure,acceleration magnification factor(AMF)of isolated structure and isolation efficiency of the isolation layer differ from those on rigid foundation with an soil-structure interaction(SSI)effect,represented by the reduction in fundamental vibration frequency of isolated structure and the increase of damping ratio with changes of the SSI effect.SSI can either increase or decrease AMF of isolated structure on soft site,depending on the characteristics of earthquake motion input.Furthermore,the isolation efficiency of isolation layer on soft site is decreased with the SSI effect,which is related to the peak ground acceleration(PGA)and the characteristics of earthquake motion input.

ISOLATION AND STRUCTURE ELUCIDATION OF A NOVEL STEROL FROM THE SOUTH CHINA SEA SPONGE DYSIDEA SP.

A novel and unusual sterol with unsaturation in the△^(5(14)) position,5α-cholesta-8(14),24(25)-diene-3β,6α-diol 1,was isolated from the South China Ses sponge Dysidea sp.The structure and relative stereochemistry of 1 was established by spectral analysis and comparison to the spectral data of known sterols.

Dynamic Analysis for Structures Isolated with Dampers

In this paper, mathematical models and dynamic analyses for both SDOF and MDOF structures isolated with dampers are established and performed, and a comprehensive computation method is provided. The shock absorbing effect is illustrated through an example of a two DOF damper-isolated system excited by sinusoidal waves and actual ground acceleration input recorded in earthquakes. It is shown that most of the responses of the structure with dampers reduce greatly near the resonant zone, but acceleration is enlarged in the lower or higher frequency zone; among various parameters, the influence of frictional coefficient n is the most significant, that of damping ratio of the dampers , is the second, and that of stiffness coefficient of the dampers k, is the slightest.

ISOLATION AND STRUCTURE DETERMINATION OF XF-1,A NEW ANTHRACYCLINE ANTIBIOTIC

A new Mutactimycin group antibiotic(XF-1)was isolated from the mycelium of Streptomyces sp.80-115 and its structure has been determined on the basis of its spectroscopical and chemical properties. XF-1 showed active against some Gram positive bacteria.

ISOLATION AND STRUCTURE DETERMINATION OF LAMIOPHLOMICL C,A NEW HIGHLY OXYGENATED IRIDOID FROM LAMIOPHLOMIS ROTATA

A new highly oxygenated iridoid,lamiophlomiol C,was isolated from the roots of Lamiophlomis rotata and its structure was elucidated by spectrosoopic techniques and X-ray diffraction.

Seismic performance of isolation system of rolling friction with springs

In order to study an isolation system of rolling friction with springs, computer programs were compiled to evaluate the seismic performance based on its movement characteristics. Through the programs, the influences of various seismic performance factors, e.g., rolling friction coefficient, spring constant, were systematically investigated. Results show that by increasing the rolling friction coefficient, the structural relative displacement due to seismic load effectively decreases, while the structural response magnitude varies mainly depending on the correlations between the following factors: the spring constant, the earthquake intensity, and the rolling friction coefficient. Furthermore, increasing the spring constant can decrease the structural relative displacement, as well as residual displacement, however, it increases the structural response magnitude. Finally, based on the analyses of various seismic performance factors subjected to the scenario earthquakes, optimized theoretical seismic performance can be achieved by reasonably combining the spring constant and the rolling friction coefficient.

Isolation and Identification of Staphylococcus chromogenes and 3 D Structural Analysis of the katA Gene

[Objective]Staphylococcus arthritis became an increasingly significant health problem in intensive chicken farming in China.[Method]In this study,a bacteria strain was isolated from the broiler chicken suffering from arthritis and named as the strain Gg1.[Result]It was then identified as Staphylococcus chromogenes by the biochemical tests and phylogenetic tree analysis based on 16S rDNA sequence.Furthermore,the catalase（katA）gene was amplified by PCR using the designed primers,and the expected fragment was 1 232 bp long encoding a protein of 410 amino acids that shares the conserved motifs including catalase,heme-binding ligand and active center motif.Six phosphorylation sites（Ser95,Thr96,Ser241,Ser242,Thr281,Ser338）,four conserved residues（Ser95,His216,Tyr281,Asp341）and two active sites（His56,Asn129）were demonstrated by multiple sequence alignment and homology comparisons.The homology modeling of 3D structure of katA protein was done by SWISSMODEL server based on the template retrieved from the catalase（PDB：2ISA_A）of Vibrio salmonicida.The katA protein represents a four-domain globular protein,the quality and reliability of the resulting protein structure was further verified by Ramachandran plot.[Conclusion]To our knowledge,this is the first report of S.chromogenes linked to arthritis in chicken and the bioinformatic characterization of its katA gene.

A bio-inspired spider-like structure isolator for low-frequency vibration

This paper proposes a quasi-zero stiffness(QZS)isolator composed of a curved beam(as spider foot)and a linear spring(as spider muscle)inspired by the precise capturing ability of spiders in vibrating environments.The curved beam is simplified as an inclined horizontal spring,and a static analysis is carried out to explore the effects of different structural parameters on the stiffness performance of the QZS isolator.The finite element simulation analysis verifies that the QZS isolator can significantly reduce the first-order natural frequency under the load in the QZS region.The harmonic balance method(HBM)is used to explore the effects of the excitation amplitude,damping ratio,and stiffness coefficient on the system’s amplitude-frequency response and transmissibility performance,and the accuracy of the analytical results is verified by the fourth-order Runge-Kutta integral method(RK-4).The experimental data of the QZS isolator prototype are fitted to a ninth-degree polynomial,and the RK-4 can theoretically predict the experimental results.The experimental results show that the QZS isolator has a lower initial isolation frequency and a wider isolation frequency bandwidth than the equivalent linear isolator.The frequency sweep test of prototypes with different harmonic excitation amplitudes shows that the initial isolation frequency of the QZS isolator is 3 Hz,and it can isolate 90%of the excitation signal at 7 Hz.The proposed biomimetic spider-like QZS isolator has high application prospects and can provide a reference for optimizing low-frequency or ultra-low-frequency isolators.

The antifungal properties of terpenoids from the endophytic fungus Bipolaris eleusines

A series of terpenoids(1-17),comprising six new compounds designated bipolariterpenes A-F(1-6)and eleven rec-ognized compounds(7-17),were isolated from the wheat culture of the potato endophytic fungus Bipolaris eleusines.Their structures and stereochemistry were clarified by HRESIMS,NMR,DP4+probability analyses,and computations for electronic circular dichroism(ECD).All compounds are made up of six meroterpenoids,four sesterterpenes and seven sesquiterpenes.Among them,four sesterterpenes(4,5,10,11)were investigated for their antifungal,antibacterial and cytotoxic properties,and six meroterpenoids(1-3,7-9)were evaluated for their antifungal properties.The compounds 7,9,and 10 had substantial antifungal activity against Epidermophyton floccosum at a concentration of 100μM.No antibacterial and cytotoxic activities were observed.

The height-width ratio limited value for rubber bearing isolated structure computed by uniform design method

Rubber isolation is the most mature control technology in practical application, and is widely used by short rigid buildings. However, many high isolation buildings have been built around the world in recent years, which do not follow the existing criterions and codes. Many researchers began to research the special problems caused by larger height-width ratio isolation structures. The overturning effect of high height-width ratio structures with rubber bearing is firstly studied. Considering the main factors, such as the height-width ratio of structures, type of site, the designed basic acceleration of ground motion and the decouple factor in horizon, computing experiment is defined with the Uniform Design Method, which is also known as designing isolation structure. The forces of the bearing under edge of structures based on the position of the rubber bearing are calculated. The result indicates that the rubber bearings will lose its functionality under very high tension and compressing force of earthquake motion in horizon and vertical, when the height-width ratio is over a certain value. Thus, based on the calculation result of isolation structures defined in the uniform design method, regression analysis is conducted, and also the rubber edge force regression formula are gotten, which has higher correlation and smaller standard deviation. This formula can be used to roughly calculate whether the pull force occurs at the edge of the building. By the edge bearings of isolation structure minimum force formula, the height-width ratio limited value of the isolation structure is deducted when rubber bearing has minimum force of zero.

Engineering practice of seismic isolation and energy dissipation structures in China

The concepts of seismic isolation and energy dissipation structures emerged in the early 1970s.In China,the first seismic isolation structure was finished in 1993,and the first energy dissipation structure was built at about the same time.Up to 2007,China had more than 600 seismic isolation and about 100 energy dissipation building structures.In 2008,the huge Wenchuan earthquake hit the southwest of China,which triggered a bloom of new seismic isolation and energy dissipation structures.This paper presents the development history and representative applications of seismic isolation and energy dissipation structures in China,reviews the state-of-the-practice of Chinese design,and discusses the challenges in the future applications.Major findings are as follows:Basic design procedures are becoming standardized after more than ten years of experiences,which mainly involve determination of design earthquake forces,selection of ground motions,modeling and time-history analyses,and performance criteria.Nonlinear time-history analyses using multiple ground motions are the characteristic of the design of seismic isolation and energy dissipation structures.Regulations,standardization and quality control of devices,balance between performance and cost,comparison with real responses,and regular inspection are identified as the issues that should be improved to further promote the application of seismic isolation and energy dissipation structures in China.

Dynamic Interaction of Soil-Isolated Structure:A Systematic Review

Isolation technique of ground structure is a hot topic in the field of earthquake engineering and structure dynamics.Since soil-isolated structure dynamic interaction study is of great significance to enhance seismic performance of isolated structures and revision of relevant isolation specifications,research on dynamic interaction of soil-isolated structure has attracted more and more attention.Based on the basic theory of soil-structure dynamic interaction,we summarize and analyze the research status quo of soil-isolated structure dynamic interaction by means of theoretical analysis,numerical simulation,model test,prototype observation and seismic performance.After reviewing the results of previous research,we reveal that some key issues,which can be used to uncover dynamic interaction mechanism and seismic response characteristics of soil-isolated structures interaction system,should not be neglected.Based on the concept of seismic performance design and the latest research of soil-isolated structure dynamic interaction,we predict the future development of soil-isolated structure dynamic interaction by elastoplastic time history analysis method,seismic performance level and practical analysis method based on energy.