Growth responses of the newly-discovered Cd-hyperaccumulator Rorippa globosa and its accumulation characteristics of Cd and As under joint stress of Cd and As

Rorippa globosa has been identified as a newly-found Cd-hyperaccumulating species.In the present study,growth responses of Rorippa globosa and its accumulation characteristics of Cd and As were examined under joint stress of Cd and As.The results showed that Cd and As had an antagonistic effect on enhancing the growth of Rorippa globosa plants and Cd uptake and accumulation under the low concentration Cd and As treatments.When the concentra-tion of Cd in the soil was 10 mg/kg and the concentration of As was 50 mg/kg,the highest growing height of the plant was up to 35.9 cm and the dry weight of the shoots was up to 2.2 g/pot,respectively.Meanwhile,the accumulation of Cd in the leaves under the joint stress was higher than that at the same level under single Cd pollution.However,there were synergic adverse effects on plant growth and Cd uptake under the combined pollution from a high concentration of Cd and As.Meanwhile,the accumulation of As in the roots was greater than that in the shoots,the translocation factor(TF)was h0.3 and the bioaccumulation factor(BF)was h0.6,thus showing that Rorippa globosa had an excluding effect on As uptake.These results confirmed that Rorippa globosa had a strong tolerant ability to the joint stress of Cd and As,and the potential for phytoremediation of soils contaminated by Cd and As.

Multiaxial Fatigue Analyses of Stress Joints for Deepwater Steel Catenary Risers

In the present study, the dynamic and fatigue characteristics of two types of stress joints are investigated under ocean environmental condition. Connected with the riser and the platform, stress joint at the vessel hang-off position should be one of the main critical design challenges for a steel catenary riser （SCR） in deepwater. When the riser is under a high pressure and deepwater working condition, the stress state for the joint is more complex, and the fatigue damage is easy to occur at this position. Stress joint discussed in this paper includes two types： Tapered Stress Joint （TSJ） and Sleeved Stress Joint （SSJ）, and multiaxial fatigue analysis results are given for comparison. Global dynamic analysis for an SCR is performed first, and then the local boundary conditions obtained from the previous analysis are applied to the stress joint FE model for the later dynamic and multiaxial fatigue analysis. Results indicate that the stress level is far lower than the yield limit of material and the damage induced by fatigue needs more attention. Besides, the damage character of the two types of stress joints differs： for TSJ, the place where the stress joint connects with the riser is easy to occur fatigue damage; for SSJ, the most probable position is at the place where the end of the inner sleeve pipe contacts with the riser body. Compared with SSJ, TSJ shows a higher stress level but better fatigue performance, and it will have a higher material cost. In consideration of various factors, designers should choose the most suitable type and also geometric parameters.

Design and Analysis of Tapered Stress Joint for Top Tensioned Riser System

Stress Joint （SJ） plays a key role in the Top Tensioned Riser （TTR） system for deep water engineering. A preliminary design method of tapered SJ is proposed in the paper, which could help designers obtain accurate design data. After a further sensitive analysis is carried out, the related parameters choice and control methods are recommended in the engineering practice. By taking the extreme environment conditions into consideration, the effects of bending stress reduction and curve control are analyzed, and the 3-D FE models are established by ABQOUS for numerical evaluation to verify the correctness of design results. At last, dynamic analysis and fatigue analysis, based on actual project, are carried out with designed stress joint. The analysis results prove the feasibility and guidance of this method in the practical engineering applications.

Finite element analysis of stress and strain distributions in mortise and loose tenon furniture joints

We studied the effect of loose tenon dimensions on stress and strain distributions in T-shaped mortise and loose tenon （M＆amp;LT） furni-ture joints under uniaxial bending loads, and determined the effects of loose tenon length （30, 45, 60, and 90 mm） and loose tenon thickness （6 and 8 mm） on bending moment capacity of M＆amp;LT joints constructed with polyvinyl acetate （PVAc） adhesive. Stress and strain distributions in joint elements were then estimated for each joint using ANSYS finite element （FE） software. The bending moment capacity of joints increased significantly with thickness and length of the tenon. Based on the FE analysis results, under uniaxial bending, the highest shear stress values were obtained in the middle parts of the tenon, while the highest shear elastic strain values were estimated in glue lines between the tenon sur-faces and walls of the mortise. Shear stress and shear elastic strain values in joint elements generally increased with tenon dimensions and corre-sponding bending moment capacities. There was consistency between predicted maximum shear stress values and failure modes of the joints.

Stresses induced by post-tensioned anchor in jointed rock mass

A new analytical study on stresses around a post-tensioned anchor in rocks with two perpendicular joint sets is presented. The assumptions of orthotropic elastic rock with plane strain conditions are made in derivation of the formulations. A tri-linear bond-slip constitutive law is used for modeling the tendon-grout interface behavior and debonding of this interface. The bearing plate width is also considered in the analysis. The obtained solutions are in the integral forms and numerical techniques that have been used for evaluation. In the illustrative example given, the major principal stress is compressive in the anchor free zone and compressive stress concentrations of 815 k Pa and 727 k Pa(for the anchor load of 300 k N) are observed under the bearing plate and the bond length proximal end, respectively. However, large values of tensile stresses with the maximum of-434 k Pa are formed at the bond length distal end. The results obtained using the proposed solution are compared very those of numerical method(FEM).

Effects of laser heat treatment on the fracture morphologies of X80 pipeline steel welded joints by stress corrosion

The surfaces of X80 pipeline steel welded joints were processed with a CO2 laser, and the effects of laser heat treatment （LHT） on H2S stress corrosion in the National Association of Corrosion Engineers （NACE） solution were analyzed by a slow strain rate test. The fracture morphologies and chemical components of corrosive products before and after LHT were analyzed by scanning electron microscopy and energy-dispersive spectroscopy, respectively, and the mechanism of LHT on stress corrosion cracking was discussed. Results showed that the fracture for welded joints was brittle in its original state, while it was transformed to a ductile fracture after LHT. The tendencies of hydrogen-induced corrosion were reduced, and the stress corrosion sensitivity index decreased from 35.2% to 25.3%, indicating that the stress corrosion resistance of X80 pipeline steel welded joints has been improved by LHT.

EFFECT OF MEAN STRESS ON FATIGUE PERFORMANCE OF WELDED JOINTS TREATED BY UPT

The fatigue contrast tests of unload longitudinal direction comer joints asoriginal welded and treated by ultrasonic peening of Q235B in various stress ratio are directed. Theimprovements of fatigue performance of unload longitudinal direction corner joints resulted byultrasonic peening are studied. The effect pattern of stress ratio on fatigue performance of weldedjoints that are treated by ultrasonic peening is studied. As tests results indicate that: ① In thecondition of stress ratio .R=-l, the fatigue strength 'of specimen treated by ultrasonic peening isincreased by 165 percent of that of the original welded specimen. And the fatigue life of specimentreated by ultrasonic peening is as much as 75 approx 210 times of that of the latter. When R=0.1,the fatigue strength is increased by 87 percent and the fatigue life is extended by 21 approx 29times. When R=-0.5, the fatigue strength is increased by 123 percent and the fatigue life isextended by 42 approx 59 times. When R=0.45, the fatigue strength is increased by 51 percent and thefatigue life is extended by 3 approx 14 times. ② If the welded joints are treated by ultrasonicpeening, the fatigue strength is no longer independent on the applied mean stress. The more thestress ratio R, the less the fatigue stress range which can be sustained by the joints is. ③Whether the high value residual stress is in the joints or not, the dead load portion of the appliedload must be considered in the design of the joints which should be treated by ultrasonic peening.

Dynamic Stress Analysis of the Leg Joints of Self-Elevating Platform

Since a self-elevating platform often works in water for a long time, the lattice leg is largely influenced by wave and current. The amplitude of leg joint stresses is a very important factor for the fatigue life of the platform. However, there are not many researches having been done on the mechanism and dynamic stress analysis of these leg joints. This paper focuses on the dynamic stress analysis and suppression methods of the leg joints of self-elevating platforms. Firstly, the dynamic stresses of the lattice leg joints are analyzed for a self-elevating platform by use of the 5th-order Stokes wave theory. Secondly, the axial and bending stresses are studied due to their large contributions to total stresses. And then, different joint types are considered and the leg-hull interface stiffness is analyzed for the improvement of the joint dynamic stress amplitude. Finally, some useful conclusions are drawn for the optimization design of the self-elevating platform.

Possibility of Inducing Compressive Residual Stresses in Welded Joints of SS400 Steels

Since the welded constructions produce easily stress corrosion cracking (SCC) or fatigue disruption in corrosive medium or under ripple load, two methods inducing compressive stress on structural surfaces by anti-welding-heating treatment (AWHT) and explosion treatment (ET) are presented. The results show that they are good ways to resisting SCC on the welded SS400 steel or other components.

Failure behavior around a circular opening in a rock mass with non-persistent joints:A parallel-bond stress corrosion approach

The stability of underground excavations is influenced by discontinuities interspaced in surrounding rock masses as well as the stress condition. In this work, a numerical study was undertaken on the failure behavior around a circular opening in a rock mass having non-persistent open joints using PFC software package. A parallel-bond stress corrosion(PSC) approach was incorporated to drive the failure of rock mass around the circular opening, such that the whole progressive failure process after excavation was reproduced. Based on the determined micro parameters for intact material and joint segments, the failure process around the circular opening agrees very well with that obtained through laboratory experiment. A subsequent parametric study was then carried out to look into the influence of lateral pressure coefficient, joint dip angle and joint persistency on the failure pattern and crack evolution of the rock mass around the circular opening. Three failure patterns identified are step path failure, planar failure and rotation failure depending on the lateral pressure coefficient. Moreover, the increment of joint dip angle and joint persistency aggravates the rock mass failure around the opening. This study offers guideline on stability estimation of underground excavations.

The jointing stress analysis of one-shot seal-off high-voltage vacuum interrupters

The free shrinkage of ceramic or metal is restricted due to solidification of the solder. Hence the shrinkage stress arises and the jointing strength is reduced during the brazing of high-voltage vacuum interrupters （HVVIs）. The solder bound contour was gained by solved energy bound equation. The finite element model of weld beads was established with Surface Evolver software. Then the stress in two different cooling techniques （ natural cooling and force cooling） was calculated with ANSYS. Comparing the stress, a better cooling technique was selected for HVVIs. Its cooling time is shortened by 3 hours while the jointing stress doesn＇ t increase and the tensile strength of ceramic to metal seal is not decreased. The stress-rupture tests have validated the calculated results. More important, a method is found, by which the brazing technique could be improved in advance instead of blind experiments.

An investigation on the performance of stress corrosion cracking in aluminum-copper alloy welded joint

With the resistance to stress corrosion of the base metal as a reference, the contrast result of stress corrosion cracking （ SCC） susceptibility of aluminum-copper alloy 2219 and 2014 welded joints under different welding processes （ VP-TIG welding, HF-TIG hybrid welding, laser-TIG hybrid welding and laser HF-TIG hybrid welding） is obtained via the slow strain rate testing （ SSRT） , scanning electron microscope （ SEM） and microstructure observation auxiliary technologies. Test results show that the joints of aluminum alloy 2219, welded by hybrid welding processes, have superior resistance to stress corrosion compared to those welded by the VP-TIG welding process in varying degrees, especially, the joint welded by the laser HF-TIG hybrid welding process, where the resistance to stress corrosion is almost the same as that of the base material. However, the HF or laser hybrid welding effect is not significant under the same welding conditions for welded joints of aluminum alloy 2014.

Stress Analysis of Bolted Joints Part II. Contact and Slip Analysis of a Four Bolt Joint

For up-to-date bolted joints, first of all in vehicles, high strength bolts of 10.9 or even 12.9 are used, which are preloaded up to 90% or even 100% of the yield strength. The primary aim of this high degree utilization is the weight reduction. For the analytic dimensioning of bolted joints, the VDI 2230 Richtlinien German standard [1] provides support. However, the analytic model can mostly consider the true structural characteristics only in a limited way. The analytic modeling is especially uncertain in case of multiple bolted joints when the load distribution among the bolts depends reasonably upon the elastic deformation of the participating elements in the joints over the geometry of the bolted joint. The first part of this paper deals with the problems of numerical modeling and stress analysis, respectively specifying the analytic dimensioning procedure by applying elastic or rather elastic-plastic material law. The error magnitude in bolted joint calculation was examined in case of omitting the existing threaded connection—between the bolt and the nut—in order to simplify the model. The second part of the paper deals with the dimensioning of stands and cantilevers’ multi-bolt fixing problems, first of all, with the load distribution among the bolts keeping in view the analysis of the local slipping relations. For demonstrating the above technique, an elaborated numeric procedure is presented for a four-bolted cantilever, having bolted joints pre-tightened to the yield strength.

Theoretical study and numerical simulation of the stress fields of the Al_2O_3 joints brazed with composite filler materials

Non-linear finite element code MSC. Marc was utilized to analysis the field of stress of the Al2O3 joints brazed with composite filler materials. The properties of the filler materials were defined by using the mixing law, method of Mori-Tanaka and theory of Eshelby to ensure the accuracy and reliability of results of finite element method （FEM）. The results show stress in brazed beam is higher than that in base material. The maximal stress can be found in the interface of joint. And the experimental results show that the shear strength of joints increases from 93.75 MPa （ Al2O3p Ovol. % ） to 135.32 MPa （ Al2O3p 15vol. % ） when composition of titanium is 3wt% in the filler metal.

Residual stress relaxation in typical weld joints and its effect on fatigue and crack growth

Many factors influence the fatigue and crack growth behavior of welded joints. Some structures often undergo fairly large static loading before they enter service or variable amplitude cyclic loading when they are in service. The combined effect of both applied stress and high initial residual stress is expected to cause the residual stresses relaxation. Only a few papers seem to deal with appropriate procedures for fatigue analysis and crack growth by considering the combined effect of variable amplitude cyclic loading with residual stresses relaxation. In this article, some typical welded connections in ship-shaped structures are investigated with 3-D elastic-plastic finite element analysis. The effect of residual stress relaxation, initial residual stress, and the applied load after variable amplitude cyclic loading is revealed, and a formula for predicting the residual stress at hot spot quantitatively is proposed. Based on the formula, an improved fatigue procedure is introduced. Moreover, crack growth of typical weld joints considering residual stresses relaxation is studied.

Influence of geometric parameters on stress concentration factors of undermatched butt joint with single V-groove under three-point bending load

In order to improve the bending load-carrying capacity （BLCC） of undermatched butt joint under three-point bending load, the influence of joint geometric parameters on stress concentration factors （SCF） at the weld bottom center and the weld toe of uudermatched butt joint with single V-groove are studied respectively based on the finite element method in this paper. Results show that the reinforcement height and the cover pass width play decisive role in the BLCC for undermatched butt joint. BLCC of undermatched butt joint can be improved by choosing the appropriate joint geometric parameters.

The Stress Concentration of Multiplanar Tubular Joints of Offshore Structure

The formulation for the stress concentration matrix of multiplanar tubular joint with braces subjected to combined load is established in this paper. The formulations for SCF values of multiplanar tubular joints are compared with those by Wordsworth and Efthymiou. The stiffening effect and load-interaction effect are discussed. A spatial offshore jacket with braces subjected to combined load is computed as a numerical example. The maximum stress of each multiplanar tubular joint and its location are found through SCF matrix. Finally, the difference between the maximum stresses of multiplanar tubular joints and their corresponding uniplanar tubular joints are discussed.

Stress Analysis of Spatial Non-Concurrent Tubular Joints

The formulations of analytic-numerical method for the stress analysis of non-concurrent spatial tubular joints are introduced in the paper. The spatial DT joints with different eccentricity in the vertical diametrical plane of chord are computed. Finally the influence of eccentricity on the stress at possible hot spots is discussed.

Stress corrosion behavior of pipeline steel(X52)welded joint

The resistance of pipeline steel joint welded by submerged arc welding to stress corrosion cracking (SCC) at its different regions in boiling mixed nitrate solution and in H,S saturated solution at room temperature is examined by the constant-load tension method. The result shows that when tested in nitrate, the weld metal may be the weakest link of the joint if the welding material doesn't match well. The resistance to SCC of the joint in H2S is very low, especially at the bond and coarse grain zone and is closely dependent on the metallurgical quality of base metal.