Bunch-length measurement at a bunch-by-bunch rate based on time–frequency-domain joint analysis techniques and its application

This paper presents a new technique for measuring the bunch length of a high-energy electron beam at a bunch-by-bunch rate in storage rings.This technique uses the time–frequency-domain joint analysis of the bunch signal to obtain bunch-by-bunch and turn-by-turn longitudinal parameters,such as bunch length and synchronous phase.The bunch signal is obtained using a button electrode with a bandwidth of several gigahertz.The data acquisition device was a high-speed digital oscilloscope with a sampling rate of more than 10 GS/s,and the single-shot sampling data buffer covered thousands of turns.The bunch-length and synchronous phase information were extracted via offline calculations using Python scripts.The calibration coefficient of the system was determined using a commercial streak camera.Moreover,this technique was tested on two different storage rings and successfully captured various longitudinal transient processes during the harmonic cavity debugging process at the Shanghai Synchrotron Radiation Facility(SSRF),and longitudinal instabilities were observed during the single-bunch accumulation process at Hefei Light Source(HLS).For Gaussian-distribution bunches,the uncertainty of the bunch phase obtained using this technique was better than 0.2 ps,and the bunch-length uncertainty was better than 1 ps.The dynamic range exceeded 10 ms.This technology is a powerful and versatile beam diagnostic tool that can be conveniently deployed in high-energy electron storage rings.

Mechanical strength analysis of SMT solder joints by finite element method

In this paper,the finite element calculation is applied to the analysis of stress inside the SMT solder joints.The effects of the solder joints'shape,the voids inside them and the quantity of solder on the mechanical strength of the SMT solder joints are analyzed and compared This is essential to the design of the SMT solder joints and soldering techniques.

Joint Analysis Method for Major Genes Controlling Multiple Correlated Quantitative Traits

Based on the major gene and polygene mixed inheritance model for multiple correlated quantitative traits, the authors proposed a new joint segregation analysis method of major gene controlling multiple correlated quantitative traits, which include major gene detection and its effect and variation estimation. The effect and variation of major gene are estimated by the maximum likelihood method implemented via expectation-maximization （EM） algorithm. Major gene is tested with the likelihood ratio （LR） test statistic. Extensive simulation studies showed that joint analysis not only increases the statistical power of major gene detection but also improves the precision and accuracy of major gene effect estimates. An example of the plant height and the number of tiller of F2 population in rice cross Duonieai x Zhonghua 11 was used in the illustration. The results indicated that the genetic difference of these two traits in this cross refers to only one pleiotropic major gene. The additive effect and dominance effect of the major gene are estimated as -21.3 and 40.6 cm on plant height, and 22.7 and -25.3 on number of tiller, respectively. The major gene shows overdominance for plant height and close to complete dominance for number of tillers.

Civil Aircraft Assisted Space-Air-Ground Integrated Networks: Architecture Design and Coverage Analysis

In this paper, we propose a novel AIenabled space-air-ground integrated networks(SAGIN). This new integrated networks architecture consists of LEO satellites and civil aircrafts carrying aerial base stations, called "civil aircraft assisted SAGIN(CAA-SAGIN)". The assistance of civil aircrafts can reduce the stress of satellite networks, improve the performance of SAGIN, decrease the construction cost and save space resources. Taking the Chinese mainland as an example, this paper has analyzed the distribution of civil aircrafts, and obtained the coverage characteristics of civil aircraft assisted networks(CAAN). Taking Starlink as the benchmark, this paper has calculated the service gap of CAAN, and designed the joint coverage constellation. The simulation results prove that the number of satellites in CAASAGIN can be greatly reduced with the assistance of civil aircrafts at the same data rate.

NEW SAR IMAGE INTERPRETATION METHOD OF AIRCRAFT BASED ON JOINT TIME-FREQUENCY ANALYSIS

With the continuous improvement of Synthetic Aperture Radar(SAR) resolution, interpreting the small targets like aircraft in SAR images becomes possible and turn out to be a hot spot in SAR application research. However, due to the complexity of SAR imaging mechanism, interpreting targets in SAR images is a tough problem. This paper presents a new aircraft interpretation method based on the joint time-frequency analysis and multi-dimensional contrasting of basic structures. Moreover, SAR data acquisition experiment is designed for interpreting the aircraft. Analyzing the experiment data with our method, the result shows that the proposed method largely makes use of the SAR data information. The reasonable results can provide some auxiliary support for the SAR images manual interpretation.

Test analysis of detection of damage to a complicated spatial model structure

A two-stage damage detection approach is proposed and experimentally demonstrated on a complicated spatial model structure with a limited number of measurements. In the experiment,five known damage patterns,including 3 brace damage cases and 2 joint damage cases,were simulated by removing braces and weakening beam鈥揷olumn connections in the structure. The limited acceleration response data generated by hammer impact were used for system identification,and modal parameters were extracted by using the eigensystem realization algorithm. In the first stage,the possible damaged locations are determined by using the damage index and the characteristics of the analytical model itself,and the extent of damage for those substructures identified at stage I is estimated in the second stage by using a second-order eigen-sensitivity approximation method. The main contribution of this paper is to test the two-stage method by using the real dynamic data of a complicated spatial model structure with limited sensors. The analysis results indicate that the two-stage approach is ableto detect the location of both damage cases,only the severity of brace damage cases can be assessed,and the reasonable analytical model is critical for successful damage detection.

An Average Failure Index Method for the Tensile Strength Prediction of Composite Adhesive-bonded π Joints

An average failure index method based on accurate FEA was proposed for the tensile strength prediction of composite out-of-plane adhesive-bonded π joints. Based on the simple and independent maximum stress failure criterion, the failure index was introduced to characterize the degree of stress components close to their corresponding material strength. With a brief load transfer analysis, the weak fillers were prominent and further detailed discussion was performed. The maximum value among the average failure indices which were related with different stress components was filtrated to represent the failure strength of the critical surface, which is either the two curved upside surfaces or the bottom plane of the fillers for composite π joints. The tensile strength of three kinds of π joints with different material systems, configurations and lay-ups was predicted by the proposed method and corresponding experiments were conducted. Good agreements between the numerical and experimental results give evidence of the effectiveness of the proposed method. In contrast to the existed time-consuming strength prediction methods, the proposed method provides a capability of quickly assessing the failure of complex out-of-plane joints and is easy and convenient to be widely utilized in engineering.

The Numerical Analysis of Strain Behavior at Solder Joint and Interface of Flip Chip Package

The flip chip package is a kind of advanced electri ca l packages. Due to the requirement of miniaturization, lower weight, higher dens ity and higher performance in the advanced electric package, it is expected that flip chip package will soon be a mainstream technology. The silicon chip is dir ectly connected to printing circuit substrate by SnPb solder joints. Also, the u nderfill, a composite of polymer and silica particles, is filled in the gap betw een the chip and substrate around the solder joints to improve the reliabili ty of solder joints. When flip chip package specimen is tested with thermal cycl ing, the cyclic stress/strain response that exists at the underfill interfaces and solder joints may result in interfacial crack initiation and propagation. Therefore, the chip cracking and the interfacial delamination between underfill and chip corner have been investigated in many studies. Also, most researches h ave focused on the effect of fatigue and creep properties of solder joint induce d by the plastic strain alternation and accumulation. The nuderfill must have lo w viscosity in the liquid state and good adhesion to the interface after solidif ying. Also, the mechanical behavior of such epoxy material has much dependen ce on temperature in its glass transition temperature range that is usually cove red by the temperature range of thermal cycling test. Therefore, the materia l behavior of underfill exists a significant non-linearity and the assumption o f linear elastic can lack for accuracy in numerical analysis. Through numerical analysis, this study had some comparisons about the effect of linear and non -linear properties of underfill on strain behaviors around the interface of fli p chip assembly. Especially, the deformation tendency inside solder bumps could be predicted. Also, it is worthily mentioned that we have pointed out which comp onent of plastic strain, thus, either normal or shear, has dominant influence to the fatigue and creep of solder bump, which have not brought up before. About the numerical analysis to the thermal plastic strain occurs in flip chip i nterconnection during thermal cycling test, a commercial finite element software , namely, ANSYS, was employed to simulate the thermal cycling test obeyed by MIL-STD-883C. The temperatures of thermal cycling ranged from -55 ℃ to 125 ℃ with ramp rate of 36 ℃/min and a dwell time of 25 min at peak temperature. T he schematic drawing of diagonal cross-section of flip chip package composed of FR-4 substrate, silicon chip, underfill and solder bump was shown as Fig.1. Th e numerical model was two-dimensional (2-D) with plane strain assumption and o nly one half of the cross-section was modeled due to geometry symmetry. The dim ensions and boundary conditions of numerical model were shown in Fig.2. The symm etric boundary conditions were applied along the left edge of the model, and the left bottom corner was additional constrained in vertical direction to prevent body motion. The finite element meshes of overall and local numerical model was shown as Fig.3. In this study, two cases of material model were used to describe the material behavior of the underfill: the case1 was linear elastic model that assumed Young’s Modulus (E) and thermal expansion coefficient (CTE) were consta nt during thermal cycling; the case2 was MKIN model (in ANSYS) that had nonlinea r temperature-dependent stress-strain relationship and temperature-dependent CTE. The material model applied to the solder bump was ANAND model (in ANSYS) th at described time-dependent plasticity phenomenon of viscoplastic material. Bot h the FR-4 substrate and silicon chip were assumed as temperature-independent elastic material; moreover, FR-4 substrate is orthotropic while silicon chip is isotropic. From the comparison between numerical results of linear and nonlinear material a ssumption of underfill, (i.e. case1 and case2), the quantities of plastic strain around the interconnection from case1 are higher than that in case2. Thus, the linear

Statistical Method for Block in Replication Design and Its SAS Program

Large-scale genetic population used for genetic breeding researches covers a large area in the field experiment,and the effect of local control would be gradually weakened.The block in replication(BIR)design is suitable for large population,which is applied to the field experiment of genetic population.The statistical methods of analysis of variance(ANOVA)and heritability estimation in single and multiple environments were derived and implemented using the statistical analysis system(SAS)program for the analysis of BIR.As a work example,a comparison of statistical analysis between BIR design and the completely random block(CRB)design were conducted for the protein content from a panel containing 455 soybean germplasms.The results indicated the different estimates of average heritability in multiple environments.The research results provided technical support for the application of BIR design in genetics and breeding studies.

Intelligibility evaluation of enhanced whisper in joint time-frequency domain

Some factors influencing the intelligibility of the enhanced whisper in the joint time-frequency domain are evaluated. Specifically, both the spectrum density and different regions of the enhanced spectrum are analyzed. Experimental results show that for a spectrum of some density, the joint time-frequency gain-modification based speech enhancement algorithm achieves significant improvement in intelligibility. Additionally, the spectrum region where the estimated spectrum is smaller than the clean spectrum, is the most important region contributing to intelligibility improvement for the enhanced whisper. The spectrum region where the estimated spectrum is larger than twice the size of the clean spectrum is detrimental to speech intelligibility perception within the whisper context.

Inheritance of marsh spot disease resistance in cranberry common bean(Phaseolus vulgaris L.)

Common bean(Phaseolus vulgaris) is an annual legume crop that is grown worldwide for its edible dry seeds and tender pods. Marsh spot(MS) of the seeds is a physio-genic stress disease affecting seed quality in beans. Studies have suggested that this disease involves a nutritional disorder caused by manganese deficiency, but the inheritance of resistance to this disease has not been reported. A biparental genetic population composed of 138 recombinant inbred lines(RILs) was developed from a cross between an MS resistant cultivar ‘Cran09’ and an MS susceptible cultivar ‘Messina’. The 138 RILs and their two parents were evaluated for MS resistance during five consecutive years from 2015 to 2019 in sandy and heavy clay soils in Morden, Manitoba, Canada. The MS incidence(MSI) and the MS resistance index(MSRI) representing disease severity were shown to be both highly correlated heritable traits that had high broad-sense heritability values(H;) of 86.5% and 83.2%, respectively. No significant differences for MSI and MSRI were observed between the two soil types in all five-(MSI) or four-year(MSRI) data collection, but significant correlations among years were observed despite MS resistance was moderately affected by year. The MSIs and MSRIs displayed a right-skewed distribution, indicating a mixed genetic model involving a few major genes and polygenes. Using the joint segregation analysis method, the same four major genes with additive-epistasis effects showed the best fit for both traits, explaining 84.4% and85.3% of the phenotypic variance for MSI and MSRI, respectively. For both traits, the M1, M2, M3 and m4 acted as the favorable(resistant) alleles for the four genes where M and m represent two alleles of each gene. However, due to epistatic effects, only the individuals of the M1 M2 M3 M4 haplotype appeared to be highly resistant, whereas those of the m1 m2 m3 M4 haplotype were the most susceptible. The m4 allele significantly suppressed the additive effects of M1 M2 M3 on resistance, but decreased susceptibility due to the additive effects of m1 m2 m3. Further quantitative trait locus(QTL) mapping is warranted to identify and validate individual genes and develop molecular markers for marker-assisted selection of resistant cultivars.

Fourier-shape-based reconstruction of rock joint profile with realistic unevenness and waviness features

Rock joint shape characteristics,waviness and unevenness play essential but distinct roles in shear mechanism of rock joints.This study presents a novel method to generate virtual rock joint profiles with realistic waviness and unevenness features.Firstly,joint profiles are obtained by 3D laser scanning device.Secondly,quantification of waviness and unevenness is conducted by traditional method,including digital filtering technique and roughness parameter RL.Thirdly,the discrete Fourier transform(DFT)method is employed to analyze the joint outlines.Two representative Fourier shape descriptors(D3,D8)for characterization of waviness and unevenness are suggested.Then,the inverse discrete Fourier transform(IDFT)is adopted to reconstruct the joint profiles with random values of phase angles but prescribed amplitudes controlled by D3 and D8.The traditional method is then applied to the reconstructed joint profiles to examine statistically the relationships between D3 and D8 and parameters RL of waviness and unevenness,respectively.The results show that larger D8 tends to result in larger waviness while higher D3 tends to increase unevenness.Reference charts for estimation of waviness and unevenness with different pairs of D3 and D8 are also provided to facilitate implementation of random joint reconstruction.

A 249-Year Record of Floods at Appleby in Westmorland, UK

An analysis of nearly 250 years of flood records on the river Eden at Appleby-in-Westmorland has enabled a flood frequency relationship to be established. The most severe floods were in the late 18th and early 19th century. With such a long history of flooding, some remedial measures would have been expected but the local people have, to some extent, adapted to the flood hazard by means of temporary and permanent flood proofing methods such as a cemented board across a doorway and removable flood boards. These measures were overwhelmed during the 2015 flood, as were the flood gates installed by the Environment Agency in 1998. A higher level of protection from floods at Appleby is called for.

Towards a Virtual Asian-Pacific Seismological Network

Regional international cooperation in seismic data exchange and joint seismological analysis in the Asian-Pacific regions plays an important role in the reduction of earthquake disasters in these regions as well as the development of global seismology. Based on the up-to-date development of new technology and digital broadband seismology, we discussed the Asian Seismological Commission (ASC) Proposal “Asian-Pacific Seismological Data Center”. We applied the concept of virtual seismological network (Ottemoeller and Havskov, 1999) to the proposed ASC data exchange program. Based on the development of digital seismology, we introduced a concept of “modern earthquake catalogues” which include not only location parameters and magnitudes as in the conventional earthquake catalogues but also new parameters of earthquakes such as CMT, radiated energy, STF, and earthquake rupture process. We recommended a web-based regional international data exchange program between the ASC members with the purpose of forming a virtual Asian-Pacific seismological network, and the interpretation and analysis of broadband digital seismic waveforms conducted at distributed “data centers”.

Effect of Heat Input on Microstructure and Mechanical Properties of Joints Made by Bypass-Current MIG Welding–Brazing of Magnesium Alloy to Galvanized Steel

Experiments were carried out with bypass-current MIG welding–brazing of magnesium alloy to galvanized steel to investigate the effect of heat input on the microstructure and mechanical properties of lap joints. Experimental results indicated that the joint efficiency tended to increase at first and then to reduce with the increase of heat input. The joint efficiency reached its maximum of about 70% when the heat input was 155 J/mm. The metallurgical bonding between magnesium alloy and steel was a thin continuous reaction layer, and the intermetallic compound layer consisted of Mg–Zn and slight Fe–Al phases. It is concluded that bypass-current MIG welding–brazing is a stable welding process, which can be used to achieve defect-free joining of magnesium alloy to steel with good weld appearances.

Influence of a non-rotating shoulder on heat generation,microstructure and mechanical properties of dissimilar AA2024/AA7050 FSW joints

Friction stir welding （FSW） and stationary shoulder friction stir welding （SSFSW） were carried out for the butt joining of dissimilar AA2024-T3 and AA7050-T7651 aluminium alloys with thicknesses of 2 mm. A comparison between the two processes was performed by varying the welding speed while keeping the rotational speed constant, Through the analysis of the force and torque produced during welding and a simple analytical model, it was possible to show that in SSFSW there is more effective coupling with the tool and the heat produced is more efficiently distributed. This process decreases both the welding area and the diffusion at the interface of the two alloys compared with FSW. The minimum microhardness occurred at the advancing side （AS） at the interface between the thermo-mechanically affected zone （TMAZ） and the stir zone （SZ） in both processes, although the decrease was more gradual in SSFSW. This interface is also where all specimens failed for both welding technologies. An increase in tensile strength was measured in SSFSW compared with standard FSW. Furthermore, it was possible to establish the mechanical performance of the material in the fracture zone using digital image correlation.

Joint multifractal analysis based on wavelet leaders

Mutually interacting components form complex systems and these components usually have long- range cross-correlated outputs. Using wavelet leaders, we propose a method for characterizing the joint multifractal nature of these long-range cross correlations; we call this method joint multifractal analysis based on wavelet leaders （MF-X-WL）. We test the validity of tile MF-X-WL method by performing extensive numerical experiments on dual binomial measures with multifractal cross correlations and bivariate fractional Brownian motions （bFBMs） with monofractal cross correlations. Both experiments indicate that MF-X-WL is capable of detecting cross correlations in synthetic data with acceptable estimating errors. We also apply the MF-X-WL method to pairs of series from financial markets （returns and volatilities） and online worlds （online numbers of different genders and different societies） and determine intriguing joint multifractal behavior.

Motion capability analysis of a quadruped robot as a parallel manipulator

This paper presents the forward and inverse displacement analysis of a quadruped robot MANA as a parallel manipulator in quadruple stance phase, which is used to obtain the workspace and control the motion of the body. The robot MANA designed on the basis of the structure of quadruped mammal is able to not only walk and turn in the uneven terrain, but also accomplish various manipulating tasks as a parallel manipulator in quadruple stance phase. The latter will be the focus of this paper, however. For this purpose, the leg kinematics is primarily analyzed, which lays the foundation on the gait planning in terms of locomotion and body kinematics analysis as a parallel manipulator. When all four feet of the robot contact on the ground, by assuming there is no slipping at the feet, each contacting point is treated as a passive spherical joint and the kinematic model of parallel manipulator is established. The method for choosing six non-redundant actuated joints for the parallel manipulator from all twelve optional joints is elaborated. The inverse and forward displacement analysis of the parallel manipulator is carried out using the method of coordinate transformation. Finally, based on the inverse and forward kinematic model, two issues on obtaining the reachable workspace of parallel manipulator and planning the motion of the body are implemented and verified by ADAMS simulation.

Parameter studies on impact in a lap joint

To represent a loose lap joint, a beam impacting four springs with gaps is modeled. Modal analysis with base excitation is solved, and time histories of contact points are closely monitored. Using the impulse during steady state response, six influential parameters are studied： damping ratio, contact stiffness, intermediate contact position, gap, excitation amplitude and beam height. For all parameters, the system response is highly controlled by modes with two contacting springs. Each parameter＇s effect on system response is presented including unstable regions, unique trend behaviours result. Recommendations for structural designers are also noted.

Descriptors for DNA Sequences Based on Joint Diagonalization of Their Feature Matrices from Dinucleotide Physicochemical Properties

Numerical characterizations of DNA sequence can facilitate analysis of similar sequences. To visualize and compare different DNA sequences in less space, a novel descriptors extraction approach was proposed for numerical characterizations and similarity analysis of sequences. Initially, a transformation method was introduced to represent each DNA sequence with dinucleotide physicochemical property matrix. Then, based on the approximate joint diagonalization theory, an eigenvalue vector was extracted from each DNA sequence,which could be considered as descriptor of the DNA sequence. Moreover, similarity analyses were performed by calculating the pair-wise distances among the obtained eigenvalue vectors. The results show that the proposed approach can capture more sequence information, and can jointly analyze the information contained in all involved multiple sequences, rather than separately, whose effectiveness was demonstrated intuitively by constructing a dendrogram for the 15 beta-globin gene sequences.