Lithium(Li)metal is regarded as a promising anode candidate for high-energy-density rechargeable batteries.Nevertheless,Li metal is highly reactive against electrolytes,leading to rapid decay of active Li metal reserv...Lithium(Li)metal is regarded as a promising anode candidate for high-energy-density rechargeable batteries.Nevertheless,Li metal is highly reactive against electrolytes,leading to rapid decay of active Li metal reservoir.Here,alloying Li metal with low-content magnesium(Mg)is proposed to mitigate the reaction kinetics between Li metal anodes and electrolytes.Mg atoms enter the lattice of Li atoms,forming solid solution due to the low amount(5 wt%)of Mg.Mg atoms mainly concentrate near the surface of Mg-alloyed Li metal anodes.The reactivity of Mg-alloyed Li metal is mitigated kinetically,which results from the electron transfer from Li to Mg atoms due to the electronegativity difference.Based on quantitative experimental analysis,the consumption rate of active Li and electrolytes is decreased by using Mgalloyed Li metal anodes,which increases the cycle life of Li metal batteries under demanding conditions.Further,a pouch cell(1.25 Ah)with Mg-alloyed Li metal anodes delivers an energy density of 340 Wh kg^(-1)and a cycle life of 100 cycles.This work inspires the strategy of modifying Li metal anodes to kinetically mitigate the side reactions with electrolytes.展开更多
High energy density Li-CO_(2)batteries have attracted much attention owing to the"two birds with one stone"feature in fixing greenhouse gas CO_(2)and providing renewable energy.However,poor reversibility of ...High energy density Li-CO_(2)batteries have attracted much attention owing to the"two birds with one stone"feature in fixing greenhouse gas CO_(2)and providing renewable energy.However,poor reversibility of the discharge product Li_(2)CO_(3)is one of the main problems that limit its application,resulting in poor cycling stability and severe polarization.Herein,copper indium sulfide(CIS),a semiconducting non-precious metal sulfide,is fabricated as cathode catalysts for high-performance Li-CO_(2)batteries.Combined with the synergistic effect of bimetallic valence bonding and coordinated electron transfer,Li-CO_(2)batteries using CIS cathodes exhibit high full specific discharge capacity,excellent rate capability and cycle stability,namely it delivers a high specific full discharge capacity of 8878μAh cm^(-2),runs steadily from 10 to 100μA cm^(-2),and performs a stable long-term cycling behavior(>1050 h)under a high energy efficiency of 84%and a low charge voltage of approximately 3.4 V at 20μA cm^(-2)within 100μAh cm^(-2).In addition,a flexible Li-CO_(2)pouch cell is constructed to reveal the potential of employing CIS to fabricate flexible high energy storage devices in practical applications.This work shows a promising development pathway toward next-generation sustainable energy storage devices.展开更多
Silica aerogels have promising applications in thermal insulation,but their flammability and reaction mechanisms have rarely been investigated.The pyrolysis kinetics and thermodynamics of hydrophobic silica aerogels u...Silica aerogels have promising applications in thermal insulation,but their flammability and reaction mechanisms have rarely been investigated.The pyrolysis kinetics and thermodynamics of hydrophobic silica aerogels under N_(2) environment were studied.The kinetic and thermodynamic parameters were obtained by three model-free methods.Based on the calculated kinetic parameters,the pyrolysis mechanism of silica aerogels was discussed by the master plots method.The results indicate that the reactions of the whole pyrolysis phase can be characterized by a random nuclear model.In addition,FTIR test results show that the volatile products of silica aerogel pyrolysis are mainly hydrocarbons generated by the decomposition of hydrophobic groups(methyl groups)on the surface.Finally,the effects of pyrolysis on the properties of silica aerogels Finally,the effects of pyrolysis on the properties of silica aerogels were investigated based on the analysis results of SEM,specific surface area,pore size distribution,X-ray diffraction,XPS and infrared spectroscopy.展开更多
As one of the few renewable aromatic resources,the research of depolymerization of lignin into highvalue chemicals has attracted extensive attention in recent years.Catalytic wet aerobic oxidation(CWAO)is an effective...As one of the few renewable aromatic resources,the research of depolymerization of lignin into highvalue chemicals has attracted extensive attention in recent years.Catalytic wet aerobic oxidation(CWAO)is an effective technology to convert lignin like sodium lignosulfonate(SL),a lignin derivative,into aromatic aldehydes such as vanillin and syringaldehyde.However,how to improve the yield of aromatic aldehyde and conversion efficiency is still a challenge,and many operating conditions that significantly affect the yield of these aromatic compounds have rarely been investigated systematically.In this work,we adopted the stirred tank reactor(STR)for the CWAO process with nano-CuO as catalyst to achieve the conversion of SL into vanillin and syringaldehyde.The effect of operating conditions including reaction time,oxygen partial pressure,reaction temperature,SL concentration,rotational speed,catalyst amount,and NaOH concentration on the yield of single phenolic compound was systematically investigated.The results revealed that all these operating conditions exhibit a significant effect on the aromatic aldehyde yield.Therefore,they should be regulated in an optimal value to obtain high yield of these aldehydes.More importantly,the reaction kinetics of the lignin oxidation was explored.This work could provide basic data for the optimization and design of industrial operation of lignin oxidation.展开更多
In this study,high-gravity intensified heterogeneous catalytic ozonation is utilized for treatment of phenol-containing wastewater,and the kinetics of the direct reaction between ozone and phenol in the presence of ex...In this study,high-gravity intensified heterogeneous catalytic ozonation is utilized for treatment of phenol-containing wastewater,and the kinetics of the direct reaction between ozone and phenol in the presence of excess tertiary butanol(TBA)is investigated.It is revealed that the direct reaction between ozone and phenol in the rotating packed bed(RPB)follows the pseudo-first-order kinetics with a reaction rate constant higher than that in the conventional bubbling reactor(BR).Under different conditions of temperature,initial pH,high-gravity factor,and gaseous ozone concentration,the apparent reaction rate constant varies in the range of 0.0160–0.115 min-1.An empirical power-exponential model is established to characterize the effects of these parameters on the direct reaction between ozone and phenol by high-gravity intensified heterogeneous catalytic ozonation.展开更多
Nickel-rich layered oxide LiNi_(x)Co_(y)MnzO_(2)(NCM,x+y+z=1)is the most promising cathode material for high-energy lithium-ion batteries.However,conventional synthesis methods are limited by the slow heating rate,slu...Nickel-rich layered oxide LiNi_(x)Co_(y)MnzO_(2)(NCM,x+y+z=1)is the most promising cathode material for high-energy lithium-ion batteries.However,conventional synthesis methods are limited by the slow heating rate,sluggish reaction dynamics,high energy consumption,and long reaction time.To overcome these chal-lenges,we first employed a high-temperature shock(HTS)strategy for fast synthesis of the NCM,and the approaching ultimate reaction rate of solid phase transition is deeply investigated for the first time.In the HTS process,ultrafast average reaction rate of phase transition from Ni_(0.6)Co_(0.2)Mn_(0.2)(OH)_(2) to Li-containing oxides is 66.7(%s^(-1)),that is,taking only 1.5 s.An ultrahigh heating rate leads to fast reaction kinetics,which induces the rapid phase transition of NCM cathodes.The HTS-synthesized nickel-rich layered oxides perform good cycling performances(94%for NCM523,94%for NCM622,and 80%for NCM811 after 200 cycles at 4.3 V).These findings might also assist to pave the way for preparing effectively Ni-rich layered oxides for lithium-ion batteries.展开更多
The thermal decomposition behavior and nonisothermal reaction kinetics of the double-base gun propellants containing the mixed ester of triethyleneglycol dinitrate(TEGDN) and nitroglycerin(NG) were investigated by...The thermal decomposition behavior and nonisothermal reaction kinetics of the double-base gun propellants containing the mixed ester of triethyleneglycol dinitrate(TEGDN) and nitroglycerin(NG) were investigated by thermogravimetry(TG) and differential thermogravimetry(DTG), and differential scanning calorimetry(DSC) under the high-pressure dynamic ambience. The results show that the thermal decomposition processes of the mixed nitric ester gun propellants have two mass-loss stages. Nitric ester evaporates and decomposes in the first stage, and nitrocellulose and centralite II(C2) decompose in the second stage. The mass loss, the DTG peak points, and the terminated temperatures of the two stages are changeable with the difference of the mass ratio of TEGDN to NG. There is only one obvious exothermic peak in the DSC curves under the different pressures. With the increase in the furnace pressure, the peak temperature decreases, and the decomposition heat increases. With the increase in the content of TEGDN, the decomposition heat decreases at 0.1 MPa and rises at high pressure. The variety of mass ratio of TEGDN to NG makes few effect on the exothermic peak temperatures in the DSC curves at different pressures. The kinetic equation of the main exothermal decomposition reaction of the gun propellant TG0601 was determined as: dα/dt=1021.59(1-α)3e-2.60×104/T. The reaction mechanism of the process can be classified as chemical reaction. The critical temperatures of the thermal explosion(Tbe and Tbp) obtained from the onset temperature(Te) and the peak temperature(Tp) are 456.46 and 473.40 K, respectively. ΔS≠, ΔH≠, and ΔG≠ of the decomposition reaction are 163.57 J·mol^-1·K^-1, 209.54 kJ·mol^-1, and 133.55 kJ·mol^-1, respectively.展开更多
The prepolymerization and curing reaction kinetics of polyurethane/montmorillonite have been studied with end group analysis and FTIR respectively. It was found that the prepolymerization and curing reaction followed ...The prepolymerization and curing reaction kinetics of polyurethane/montmorillonite have been studied with end group analysis and FTIR respectively. It was found that the prepolymerization and curing reaction followed the 2nd-order kinetics. But the activation energy of prepolymerization increased from 42.7 kJ/mol to 56.5 kJ/rnol after the montmorillonite was added in the reaction system, and activation energy of curing reaction decreased from 64.4 kJ/mol to 17.5 kJ/mol. 2007 Bing Liao. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.展开更多
Based on the measurement of the released hydrogen gas pressure (PH2), the reaction kinetics between TiH2 powder and pure aluminum melt was studied at various temperatures. After cooling the samples, the interface of...Based on the measurement of the released hydrogen gas pressure (PH2), the reaction kinetics between TiH2 powder and pure aluminum melt was studied at various temperatures. After cooling the samples, the interface of TiH2 powder and aluminum melt was studied. The results show that the-time curves have three regions; in the first and second regions, the rate of reaction conforms zero and one order, respectively; in the third region, the hydrogen gas pressure remains constant and the rate of reaction reaches zero. The main factors that control the rate of reaction in the first and second regions are the penetration of hydrogen atoms in the titanium lattice and the chemical reaction between molten aluminum and titanium, respectively. According to the main factors that control the rate of reaction, three temperature ranges are considered for the reaction mechanism: (a) 700-750°C, (b) 750-800°C, and (c) 800-1000°C. In the first temperature range, the reaction is mostly under the control of chemical reaction; at the temperature range of 750 to 800°C, the reaction is controlled by the diffusion and chemical reaction; at the third temperature range (800-1000°C), the dominant controlling mechanism is diffusion.展开更多
Based on the theory of first-order reaction kinetics,a thermal reaction kinetic model in integral form has been derive.To make the model more applicable,the effects of time and the conversion degree on the reaction ra...Based on the theory of first-order reaction kinetics,a thermal reaction kinetic model in integral form has been derive.To make the model more applicable,the effects of time and the conversion degree on the reaction rate parameters were considered.Two types of undetermined functions were used to compensate for the intrinsic variation of the reaction rate,and two types of correction methods are provided.The model was explained and verified using published experimental data of different polymer thermal reaction systems,and its effectiveness and wide adaptability were confirmed.For the given kinetic model,only one parameter needs to be determined.The proposed empirical model is expected to be used in the numerical simulation of polymer thermal reaction process.展开更多
An orthogonal test was used to optimize the reaction conditions of roasting zinc oxide ore using(NH_4)_2SO_4. The optimized reaction conditions are defined as an(NH_4)_2SO_4/zinc molar ratio of 1.4:1, a roasting ...An orthogonal test was used to optimize the reaction conditions of roasting zinc oxide ore using(NH_4)_2SO_4. The optimized reaction conditions are defined as an(NH_4)_2SO_4/zinc molar ratio of 1.4:1, a roasting temperature of 440°C, and a thermostatic time of 60 min. The molar ratio of(NH_4)_2SO_4/zinc is the most predominant factor and the roasting temperature is the second significant factor that governs the zinc extraction. Thermogravimetric-differential thermal analysis was used for(NH_4)_2SO_4 and zinc mixed in a molar ratio of 1.4:1 at the heating rates of 5, 10, 15, and 20 K·min-1. Two strong endothermic peaks indicate that the complex chemical reactions occur at approximately 290°C and 400°C. XRD analysis was employed to examine the transformations of mineral phases during roasting process. Kinetic parameters, including reaction apparent activation energy, reaction order, and frequency factor, were calculated by the Doyle-Ozawa and Kissinger methods. Corresponding to the two endothermic peaks, the kinetic equations were obtained.展开更多
The kinetics mechanism of the dissociation reactions in a NO/SO2/N2/O2 system was investigated in consideration of energetic electrons' impacts on a non-thermal plasma. A model was derived from the Boltzmann equation...The kinetics mechanism of the dissociation reactions in a NO/SO2/N2/O2 system was investigated in consideration of energetic electrons' impacts on a non-thermal plasma. A model was derived from the Boltzmann equation and molecule collision theory to predict the dissociation reaction rate coefficients. Upon comparison with available literature, the model was confirmed to be acceptably accurate in general. Several reaction rate coefficients of the NO/SO2/N2/O2 dissociation system were derived according to the Arrhenius formula. The activation energies of each plasma reaction were calculated by quantum chemistry methods. The relation between the dissociation reaction rate coefficient and electron temperature was established to describe the importance of each reaction and to predict relevant processes of gaseous chemical reactions. The sensitivity of the mechanism of NO/SO2/N2/O2 dissociation reaction in a non-thermal plasma was also analysed.展开更多
Baotou RE concentrate was decomposed with concentrated sulfuric acid by controlling the roasting temperature below 500℃.Thermogravimetry-differential thermal analysis(TG-DTA) and chemical analytical methods were us...Baotou RE concentrate was decomposed with concentrated sulfuric acid by controlling the roasting temperature below 500℃.Thermogravimetry-differential thermal analysis(TG-DTA) and chemical analytical methods were used to study the thermal decomposition process and the thermal decomposition effect.The Freeman-Carroll method was applied to analyze the TG-DTA curves.The activation energy, reaction order, and reaction frequency factor at different stages were calculated.The Satava method was used to deduce the reaction mechanism and the relative reaction rate during the thermal decomposition process.展开更多
he axial coordination reactions of tetraphenylporphinatocobalt (Ⅲ) chloride(Co TPPC1) with various imidazoles RIm ( HIm . imidazole; Melm , 2-methylimida-zole) were investigated in acetone and dichloromethand so...he axial coordination reactions of tetraphenylporphinatocobalt (Ⅲ) chloride(Co TPPC1) with various imidazoles RIm ( HIm . imidazole; Melm , 2-methylimida-zole) were investigated in acetone and dichloromethand solvents at different temper-atures. The reaction mechanisms were proposed and the differences between experi-mental results in the two solvents h ave been interpreted using the proposed mecha-nisms and rate equations for the first time , and the reaction scheme for the axial re-action of the metalloporphyrin has been developed. Hydrogen bonding plays an im-portant role in the reactions. The effects of various imidazoles for these reactionsand the solvents are reported. The comparison between iron and cobalt porphyrinsin the kinetics are discussed.展开更多
An industrial mineral wollastonite (CaSiO3) was produced under solid state conditions from rice husk silica and limestone. Reaction was carried out at 900'C to 1300'C for 1 h. The product batches were subjecte...An industrial mineral wollastonite (CaSiO3) was produced under solid state conditions from rice husk silica and limestone. Reaction was carried out at 900'C to 1300'C for 1 h. The product batches were subjected to XRD and chemical analysis techniques specific for wollastonite. Mole fractions of different product batches were calculated on the basis of accumulated data to study the kinetics. Specific rate constants and reaction rate were also found out. Various probable models of mechanism for reaction were considered and testified with the laid down criterion for suggesting the suitable one. The resulting data were treated with Arrhenius equation as well and activation energy was calculated--therefrom. In addition to finding it's value from the slope of Arrhenius curve, an alternate method was also applied for this purpose. Both of the values were observed to be comparable. The activation energy required for performed reaction was found to be almost one third of that reported for synthesizing CaSiO3 by using quartz. This referred to the economical preparation of wollastonite by using rice husk as a source of silica instead of quartz.展开更多
The kinetics of PTC-Wittig reaction between substituted aromatic aldehydes and 2-butenyl methyldiphenylphosphonium salt has been studied. The low reaction constant (ρ=0. 30) implies that these PTC-Wittig reactions ta...The kinetics of PTC-Wittig reaction between substituted aromatic aldehydes and 2-butenyl methyldiphenylphosphonium salt has been studied. The low reaction constant (ρ=0. 30) implies that these PTC-Wittig reactions take place through low polar intermediate.展开更多
Cure and decomposition reaction kinetics of typical organic materials in aerospace applications are introduced.From the data of dynamic differential scanning calorimetry(DSC)experiments,and based on changes of the pea...Cure and decomposition reaction kinetics of typical organic materials in aerospace applications are introduced.From the data of dynamic differential scanning calorimetry(DSC)experiments,and based on changes of the peak temperatures(T_(p))with different heating rates(β),a linear equation,T_(p)=T_(1)+△Tlnβ,has been obtained more reasonably.The above equation can be used to explain some laws of higher or lower of apparent activation energies(E_(a)),by which the apparent activation energy(E_(a))is nearly equal to RT^(2)_(1)/△T.A number of kinetic investigations of typical thermosetting resins and energetic materials in aerospace applications were chosen to validate the above equations.展开更多
The time integration method with four-order accuracy, self-starting and implicit for the diffuse chemical reaction kinetics equation or the transient instantaneous temperature filed equation was presented. The example...The time integration method with four-order accuracy, self-starting and implicit for the diffuse chemical reaction kinetics equation or the transient instantaneous temperature filed equation was presented. The examples show that both accuracy and stability are better than Runge-Kutta method with four-order. The coefficients of the equation are stored with sparse matrix pattern, so an algorithm is presented which combines a compact storage scheme with reduced computation cost. The computation of the competitive and consecutive reaction in the rotating packed bed, taken as examples, shows that the method is effective.展开更多
The reaction kinetics of the heterogeneous oxidation of toluene with Mn 3+ was studied by considering the effects of disproportionation of Mn 3+ in reaction system, a 'parallel' modulus was set up. A...The reaction kinetics of the heterogeneous oxidation of toluene with Mn 3+ was studied by considering the effects of disproportionation of Mn 3+ in reaction system, a 'parallel' modulus was set up. And then the concentration of Mn 3+ in disproportionation and the concentration of benzaldehyde in oxidation were respectively determined in turn, the rate constant, order and pseudo activation energy of the heterogeneous oxidation were obtained by mathematical deduction and the kinetic equation was concluded. In addition, the reaction mechanism was analyzed. It shows that the results are completely consistent with modulus.展开更多
The demanganization reaction kinetics of carbon-saturated liquid iron with an eight-component slag consisting of CaO–SiO2–MgO–FeO–MnO–Al2O3–TiO2–CaF2 was investigated at 1553, 1623, and 1673 K in this study. Th...The demanganization reaction kinetics of carbon-saturated liquid iron with an eight-component slag consisting of CaO–SiO2–MgO–FeO–MnO–Al2O3–TiO2–CaF2 was investigated at 1553, 1623, and 1673 K in this study. The rate-controlling step(RCS) for the demanganization reaction with regard to the hot metal pretreatment conditions was studied via kinetics analysis based on the fundamental equation of heterogeneous reaction kinetics. From the temperature dependence of the mass transfer coefficient of a transition-metal oxide(MnO), the apparent activation energy of the demanganization reaction was estimated to be 189.46 kJ·mol^–1 in the current study, which indicated that the mass transfer of MnO in the molten slag controlled the overall rate of the demanganization reaction. The calculated apparent activation energy was slightly lower than the values reported in the literature for mass transfer in a slag phase. This difference was attributed to an increase in the "specific reaction interface"(SRI) value, either as a result of turbulence at the reaction interface or a decrease of the absolute amount of slag phase during sampling, and to the addition of calcium fluoride to the slag.展开更多
基金supported by the National Key Research and Development Program(2021YFB2400300)National Natural Science Foundation of China(22379013 and 22209010)the Beijing Institute of Technology“Xiaomi Young Scholars”program。
文摘Lithium(Li)metal is regarded as a promising anode candidate for high-energy-density rechargeable batteries.Nevertheless,Li metal is highly reactive against electrolytes,leading to rapid decay of active Li metal reservoir.Here,alloying Li metal with low-content magnesium(Mg)is proposed to mitigate the reaction kinetics between Li metal anodes and electrolytes.Mg atoms enter the lattice of Li atoms,forming solid solution due to the low amount(5 wt%)of Mg.Mg atoms mainly concentrate near the surface of Mg-alloyed Li metal anodes.The reactivity of Mg-alloyed Li metal is mitigated kinetically,which results from the electron transfer from Li to Mg atoms due to the electronegativity difference.Based on quantitative experimental analysis,the consumption rate of active Li and electrolytes is decreased by using Mgalloyed Li metal anodes,which increases the cycle life of Li metal batteries under demanding conditions.Further,a pouch cell(1.25 Ah)with Mg-alloyed Li metal anodes delivers an energy density of 340 Wh kg^(-1)and a cycle life of 100 cycles.This work inspires the strategy of modifying Li metal anodes to kinetically mitigate the side reactions with electrolytes.
基金supports by the National Natural Science Foundation of China(No.52072352,21875226,U20A2072,52102320)the Foundation for the Youth S&T Innovation Team of Sichuan Province(2020JDTD0035)+1 种基金Tianfu Rencai Plan,the Science Foundation for Distinguished Young Scholars of Sichuan Province(2017JQ0036)the Chengdu Talent plan,Science and Technology Projects for Administration for Market Regulation of Sichuan Province(SCSJ2020016).
文摘High energy density Li-CO_(2)batteries have attracted much attention owing to the"two birds with one stone"feature in fixing greenhouse gas CO_(2)and providing renewable energy.However,poor reversibility of the discharge product Li_(2)CO_(3)is one of the main problems that limit its application,resulting in poor cycling stability and severe polarization.Herein,copper indium sulfide(CIS),a semiconducting non-precious metal sulfide,is fabricated as cathode catalysts for high-performance Li-CO_(2)batteries.Combined with the synergistic effect of bimetallic valence bonding and coordinated electron transfer,Li-CO_(2)batteries using CIS cathodes exhibit high full specific discharge capacity,excellent rate capability and cycle stability,namely it delivers a high specific full discharge capacity of 8878μAh cm^(-2),runs steadily from 10 to 100μA cm^(-2),and performs a stable long-term cycling behavior(>1050 h)under a high energy efficiency of 84%and a low charge voltage of approximately 3.4 V at 20μA cm^(-2)within 100μAh cm^(-2).In addition,a flexible Li-CO_(2)pouch cell is constructed to reveal the potential of employing CIS to fabricate flexible high energy storage devices in practical applications.This work shows a promising development pathway toward next-generation sustainable energy storage devices.
基金financially supported by the National Natural Science Foundation of China(52074201&51706165)China Postdoctoral Science Foundation(2021M703082)。
文摘Silica aerogels have promising applications in thermal insulation,but their flammability and reaction mechanisms have rarely been investigated.The pyrolysis kinetics and thermodynamics of hydrophobic silica aerogels under N_(2) environment were studied.The kinetic and thermodynamic parameters were obtained by three model-free methods.Based on the calculated kinetic parameters,the pyrolysis mechanism of silica aerogels was discussed by the master plots method.The results indicate that the reactions of the whole pyrolysis phase can be characterized by a random nuclear model.In addition,FTIR test results show that the volatile products of silica aerogel pyrolysis are mainly hydrocarbons generated by the decomposition of hydrophobic groups(methyl groups)on the surface.Finally,the effects of pyrolysis on the properties of silica aerogels Finally,the effects of pyrolysis on the properties of silica aerogels were investigated based on the analysis results of SEM,specific surface area,pore size distribution,X-ray diffraction,XPS and infrared spectroscopy.
基金supported by the National Key Research and Development Program of China(2019YFA0210302)the National Natural Science Foundation of China(21878009).
文摘As one of the few renewable aromatic resources,the research of depolymerization of lignin into highvalue chemicals has attracted extensive attention in recent years.Catalytic wet aerobic oxidation(CWAO)is an effective technology to convert lignin like sodium lignosulfonate(SL),a lignin derivative,into aromatic aldehydes such as vanillin and syringaldehyde.However,how to improve the yield of aromatic aldehyde and conversion efficiency is still a challenge,and many operating conditions that significantly affect the yield of these aromatic compounds have rarely been investigated systematically.In this work,we adopted the stirred tank reactor(STR)for the CWAO process with nano-CuO as catalyst to achieve the conversion of SL into vanillin and syringaldehyde.The effect of operating conditions including reaction time,oxygen partial pressure,reaction temperature,SL concentration,rotational speed,catalyst amount,and NaOH concentration on the yield of single phenolic compound was systematically investigated.The results revealed that all these operating conditions exhibit a significant effect on the aromatic aldehyde yield.Therefore,they should be regulated in an optimal value to obtain high yield of these aldehydes.More importantly,the reaction kinetics of the lignin oxidation was explored.This work could provide basic data for the optimization and design of industrial operation of lignin oxidation.
基金supported by the Fund for Shanxi Province Higher Education“1331 Project”for Improving Quality and Efficiency Construction(nuc2021-006)Key Research&Development Plan of Shanxi Province(201903D321059)+1 种基金Scientific Activities of Selected Returned Overseas Professionals in Shanxi Province(20200004)Transformation and Cultivation Projects of Scientific and Technological Achievements in Universities of Shanxi Province Institutions(2020CG040).
文摘In this study,high-gravity intensified heterogeneous catalytic ozonation is utilized for treatment of phenol-containing wastewater,and the kinetics of the direct reaction between ozone and phenol in the presence of excess tertiary butanol(TBA)is investigated.It is revealed that the direct reaction between ozone and phenol in the rotating packed bed(RPB)follows the pseudo-first-order kinetics with a reaction rate constant higher than that in the conventional bubbling reactor(BR).Under different conditions of temperature,initial pH,high-gravity factor,and gaseous ozone concentration,the apparent reaction rate constant varies in the range of 0.0160–0.115 min-1.An empirical power-exponential model is established to characterize the effects of these parameters on the direct reaction between ozone and phenol by high-gravity intensified heterogeneous catalytic ozonation.
基金the financial support from the National Natural Science Foundation of China(Grant Nos.92372107 and 52171219).
文摘Nickel-rich layered oxide LiNi_(x)Co_(y)MnzO_(2)(NCM,x+y+z=1)is the most promising cathode material for high-energy lithium-ion batteries.However,conventional synthesis methods are limited by the slow heating rate,sluggish reaction dynamics,high energy consumption,and long reaction time.To overcome these chal-lenges,we first employed a high-temperature shock(HTS)strategy for fast synthesis of the NCM,and the approaching ultimate reaction rate of solid phase transition is deeply investigated for the first time.In the HTS process,ultrafast average reaction rate of phase transition from Ni_(0.6)Co_(0.2)Mn_(0.2)(OH)_(2) to Li-containing oxides is 66.7(%s^(-1)),that is,taking only 1.5 s.An ultrahigh heating rate leads to fast reaction kinetics,which induces the rapid phase transition of NCM cathodes.The HTS-synthesized nickel-rich layered oxides perform good cycling performances(94%for NCM523,94%for NCM622,and 80%for NCM811 after 200 cycles at 4.3 V).These findings might also assist to pave the way for preparing effectively Ni-rich layered oxides for lithium-ion batteries.
基金the National Natural Science Foundation of China(No.20573098)the Foundation of Key Laboratory of Science and Technology for National Defence of Propellant and Explosive of China(No.9140C3503020605).
文摘The thermal decomposition behavior and nonisothermal reaction kinetics of the double-base gun propellants containing the mixed ester of triethyleneglycol dinitrate(TEGDN) and nitroglycerin(NG) were investigated by thermogravimetry(TG) and differential thermogravimetry(DTG), and differential scanning calorimetry(DSC) under the high-pressure dynamic ambience. The results show that the thermal decomposition processes of the mixed nitric ester gun propellants have two mass-loss stages. Nitric ester evaporates and decomposes in the first stage, and nitrocellulose and centralite II(C2) decompose in the second stage. The mass loss, the DTG peak points, and the terminated temperatures of the two stages are changeable with the difference of the mass ratio of TEGDN to NG. There is only one obvious exothermic peak in the DSC curves under the different pressures. With the increase in the furnace pressure, the peak temperature decreases, and the decomposition heat increases. With the increase in the content of TEGDN, the decomposition heat decreases at 0.1 MPa and rises at high pressure. The variety of mass ratio of TEGDN to NG makes few effect on the exothermic peak temperatures in the DSC curves at different pressures. The kinetic equation of the main exothermal decomposition reaction of the gun propellant TG0601 was determined as: dα/dt=1021.59(1-α)3e-2.60×104/T. The reaction mechanism of the process can be classified as chemical reaction. The critical temperatures of the thermal explosion(Tbe and Tbp) obtained from the onset temperature(Te) and the peak temperature(Tp) are 456.46 and 473.40 K, respectively. ΔS≠, ΔH≠, and ΔG≠ of the decomposition reaction are 163.57 J·mol^-1·K^-1, 209.54 kJ·mol^-1, and 133.55 kJ·mol^-1, respectively.
文摘The prepolymerization and curing reaction kinetics of polyurethane/montmorillonite have been studied with end group analysis and FTIR respectively. It was found that the prepolymerization and curing reaction followed the 2nd-order kinetics. But the activation energy of prepolymerization increased from 42.7 kJ/mol to 56.5 kJ/rnol after the montmorillonite was added in the reaction system, and activation energy of curing reaction decreased from 64.4 kJ/mol to 17.5 kJ/mol. 2007 Bing Liao. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.
文摘Based on the measurement of the released hydrogen gas pressure (PH2), the reaction kinetics between TiH2 powder and pure aluminum melt was studied at various temperatures. After cooling the samples, the interface of TiH2 powder and aluminum melt was studied. The results show that the-time curves have three regions; in the first and second regions, the rate of reaction conforms zero and one order, respectively; in the third region, the hydrogen gas pressure remains constant and the rate of reaction reaches zero. The main factors that control the rate of reaction in the first and second regions are the penetration of hydrogen atoms in the titanium lattice and the chemical reaction between molten aluminum and titanium, respectively. According to the main factors that control the rate of reaction, three temperature ranges are considered for the reaction mechanism: (a) 700-750°C, (b) 750-800°C, and (c) 800-1000°C. In the first temperature range, the reaction is mostly under the control of chemical reaction; at the temperature range of 750 to 800°C, the reaction is controlled by the diffusion and chemical reaction; at the third temperature range (800-1000°C), the dominant controlling mechanism is diffusion.
基金supported by the National Key Research and Development Program of China(Grant No.2018YFB2001002)。
文摘Based on the theory of first-order reaction kinetics,a thermal reaction kinetic model in integral form has been derive.To make the model more applicable,the effects of time and the conversion degree on the reaction rate parameters were considered.Two types of undetermined functions were used to compensate for the intrinsic variation of the reaction rate,and two types of correction methods are provided.The model was explained and verified using published experimental data of different polymer thermal reaction systems,and its effectiveness and wide adaptability were confirmed.For the given kinetic model,only one parameter needs to be determined.The proposed empirical model is expected to be used in the numerical simulation of polymer thermal reaction process.
基金financially supported by the National Natural Science Foundation of China(Nos.51204054 and 51574084)the Fundamental Research Funds for the Central Universities of China(No.N150204009)the National Basic Research Priorities Program of China(No.2014CB643405)
文摘An orthogonal test was used to optimize the reaction conditions of roasting zinc oxide ore using(NH_4)_2SO_4. The optimized reaction conditions are defined as an(NH_4)_2SO_4/zinc molar ratio of 1.4:1, a roasting temperature of 440°C, and a thermostatic time of 60 min. The molar ratio of(NH_4)_2SO_4/zinc is the most predominant factor and the roasting temperature is the second significant factor that governs the zinc extraction. Thermogravimetric-differential thermal analysis was used for(NH_4)_2SO_4 and zinc mixed in a molar ratio of 1.4:1 at the heating rates of 5, 10, 15, and 20 K·min-1. Two strong endothermic peaks indicate that the complex chemical reactions occur at approximately 290°C and 400°C. XRD analysis was employed to examine the transformations of mineral phases during roasting process. Kinetic parameters, including reaction apparent activation energy, reaction order, and frequency factor, were calculated by the Doyle-Ozawa and Kissinger methods. Corresponding to the two endothermic peaks, the kinetic equations were obtained.
文摘The kinetics mechanism of the dissociation reactions in a NO/SO2/N2/O2 system was investigated in consideration of energetic electrons' impacts on a non-thermal plasma. A model was derived from the Boltzmann equation and molecule collision theory to predict the dissociation reaction rate coefficients. Upon comparison with available literature, the model was confirmed to be acceptably accurate in general. Several reaction rate coefficients of the NO/SO2/N2/O2 dissociation system were derived according to the Arrhenius formula. The activation energies of each plasma reaction were calculated by quantum chemistry methods. The relation between the dissociation reaction rate coefficient and electron temperature was established to describe the importance of each reaction and to predict relevant processes of gaseous chemical reactions. The sensitivity of the mechanism of NO/SO2/N2/O2 dissociation reaction in a non-thermal plasma was also analysed.
基金supported by the National Natural Science Foundation of China (No. 20877008)the Program for New Century Excellent Telents in University of the Ministry of Education of China (No. 20407003)
文摘Baotou RE concentrate was decomposed with concentrated sulfuric acid by controlling the roasting temperature below 500℃.Thermogravimetry-differential thermal analysis(TG-DTA) and chemical analytical methods were used to study the thermal decomposition process and the thermal decomposition effect.The Freeman-Carroll method was applied to analyze the TG-DTA curves.The activation energy, reaction order, and reaction frequency factor at different stages were calculated.The Satava method was used to deduce the reaction mechanism and the relative reaction rate during the thermal decomposition process.
文摘he axial coordination reactions of tetraphenylporphinatocobalt (Ⅲ) chloride(Co TPPC1) with various imidazoles RIm ( HIm . imidazole; Melm , 2-methylimida-zole) were investigated in acetone and dichloromethand solvents at different temper-atures. The reaction mechanisms were proposed and the differences between experi-mental results in the two solvents h ave been interpreted using the proposed mecha-nisms and rate equations for the first time , and the reaction scheme for the axial re-action of the metalloporphyrin has been developed. Hydrogen bonding plays an im-portant role in the reactions. The effects of various imidazoles for these reactionsand the solvents are reported. The comparison between iron and cobalt porphyrinsin the kinetics are discussed.
文摘An industrial mineral wollastonite (CaSiO3) was produced under solid state conditions from rice husk silica and limestone. Reaction was carried out at 900'C to 1300'C for 1 h. The product batches were subjected to XRD and chemical analysis techniques specific for wollastonite. Mole fractions of different product batches were calculated on the basis of accumulated data to study the kinetics. Specific rate constants and reaction rate were also found out. Various probable models of mechanism for reaction were considered and testified with the laid down criterion for suggesting the suitable one. The resulting data were treated with Arrhenius equation as well and activation energy was calculated--therefrom. In addition to finding it's value from the slope of Arrhenius curve, an alternate method was also applied for this purpose. Both of the values were observed to be comparable. The activation energy required for performed reaction was found to be almost one third of that reported for synthesizing CaSiO3 by using quartz. This referred to the economical preparation of wollastonite by using rice husk as a source of silica instead of quartz.
文摘The kinetics of PTC-Wittig reaction between substituted aromatic aldehydes and 2-butenyl methyldiphenylphosphonium salt has been studied. The low reaction constant (ρ=0. 30) implies that these PTC-Wittig reactions take place through low polar intermediate.
文摘Cure and decomposition reaction kinetics of typical organic materials in aerospace applications are introduced.From the data of dynamic differential scanning calorimetry(DSC)experiments,and based on changes of the peak temperatures(T_(p))with different heating rates(β),a linear equation,T_(p)=T_(1)+△Tlnβ,has been obtained more reasonably.The above equation can be used to explain some laws of higher or lower of apparent activation energies(E_(a)),by which the apparent activation energy(E_(a))is nearly equal to RT^(2)_(1)/△T.A number of kinetic investigations of typical thermosetting resins and energetic materials in aerospace applications were chosen to validate the above equations.
文摘The time integration method with four-order accuracy, self-starting and implicit for the diffuse chemical reaction kinetics equation or the transient instantaneous temperature filed equation was presented. The examples show that both accuracy and stability are better than Runge-Kutta method with four-order. The coefficients of the equation are stored with sparse matrix pattern, so an algorithm is presented which combines a compact storage scheme with reduced computation cost. The computation of the competitive and consecutive reaction in the rotating packed bed, taken as examples, shows that the method is effective.
文摘The reaction kinetics of the heterogeneous oxidation of toluene with Mn 3+ was studied by considering the effects of disproportionation of Mn 3+ in reaction system, a 'parallel' modulus was set up. And then the concentration of Mn 3+ in disproportionation and the concentration of benzaldehyde in oxidation were respectively determined in turn, the rate constant, order and pseudo activation energy of the heterogeneous oxidation were obtained by mathematical deduction and the kinetic equation was concluded. In addition, the reaction mechanism was analyzed. It shows that the results are completely consistent with modulus.
基金support from the National Natural Science Foundation of China (Nos. U1560203 and 51274031)the Beijing Key Laboratory of Special Melting and Preparation of High-End Metal Materials in the School of Metallurgical and Ecological Engineering of University of Science and Technology Beijing, China
文摘The demanganization reaction kinetics of carbon-saturated liquid iron with an eight-component slag consisting of CaO–SiO2–MgO–FeO–MnO–Al2O3–TiO2–CaF2 was investigated at 1553, 1623, and 1673 K in this study. The rate-controlling step(RCS) for the demanganization reaction with regard to the hot metal pretreatment conditions was studied via kinetics analysis based on the fundamental equation of heterogeneous reaction kinetics. From the temperature dependence of the mass transfer coefficient of a transition-metal oxide(MnO), the apparent activation energy of the demanganization reaction was estimated to be 189.46 kJ·mol^–1 in the current study, which indicated that the mass transfer of MnO in the molten slag controlled the overall rate of the demanganization reaction. The calculated apparent activation energy was slightly lower than the values reported in the literature for mass transfer in a slag phase. This difference was attributed to an increase in the "specific reaction interface"(SRI) value, either as a result of turbulence at the reaction interface or a decrease of the absolute amount of slag phase during sampling, and to the addition of calcium fluoride to the slag.