The Importance of Molecular and Clinical Laboratory Tests in Diagnosis and Treatment of Coronavirus Disease

900 abusers were tested for the presence of drug abuse and coronavirus disease.In the early stage,the throat and noise samples of these patients were examined by polymerase chain reaction(PCR).The mean age of the study group is 42±23.Hematological and serological examinations were performed on 131 patients.All data were analyzed by t-test and one-way analysis of variance(ANOVA).Therefore,P<0.05 is considered as the significance of the test results.The results showed that 131 patients in the study group had positive results of PCR tests and nearby they had Covid-19.Approximately 90%of patients with coronavirus disease showed positive serological tests and lymphopenic condition.All of urine or blood samples in the 131 patients were positive for the presence of abuse drugs.C-reactive protein(CRP)is one of important serologic test that detected on these patients.This study showed the importance of molecular genetics test such as PCR and also hematology and serology tests in distinguish of coronavirus diseases.

Evaluation of Abuse Drugs and Clinical Laboratory Tests Variations in Whole Blood ＆ Urine Samples of Abusers

In this study, five hundred urine samples and five hundred blood samples of abusers were examined for the presence of alkaloid substances and abuse drugs in urines and bloods. These numbers of blood and urine samples of addicts in clinics of welfare organization, during detoxification treatment or maintenance treatment were screened for abuse drugs presence. The all of samples were tested through as a view of clinical laboratory methods. Age ranges of female patients were 35 ~ 15 and age range of males patients were 45 ~ 15. All patients filled questionnaire and satisfy forms too. First, all fresh urine and blood samples were examined to confirm presence drugs abuses, depend on their addiction and treatment, so all samples were confirmed by two tests. Then they were examined to other clinical laboratory tests. All data were analyzed by t-test and were Anova one way and two ways of Anova Turkey, and p 〈 0.05 was considered significant. The p-value of this study was p = 0.0001. The results of this study were showed that 4% of abusers had mild increase in hematocrite level and 2% of narcotic drugs abusers had mild lower level of blood sugars than normal range and 4% of participants had increase liver enzymes such ALT （alanine transferase）, AST （aspartat transferase）, ALP （alkaline phosphatease） and 1% of them had renal failure. Although blood level BUN （blood urea nitrogen） and creatinin were examined to evaluation of their renal failure .The results in Tabriz/Iran undrevision of welfare organization clinics were approximately showed that positive results of addiction are in each of urine and blood samples. Because some of abusers directly consumed full long time agonist or partial agonists＇ drugs such as methadone and buprenorphine for their maintenance therapy in clinics. Also doing test on blood samples has high importance in distinguishing and confirmation of drugs abuse in samples. Also in this study we conclude that among all drug analytical methods the cheapest and easiest test to screening opioids and other abuse drugs in urine and blood samples is strip test for rapid diagnosis, also tests on blood samples have high importance as a view point of accuracy to distinguishing of drugs abuse, and serum levels of some other parameters showed all abusers patients situation such as liver and renal dysfimction through clinical laboratory tests.

Laboratory pull-out tests on fully grouted rock bolts and cable bolts:Results and lessons learned

Laboratory pull-out tests were conducted on the following rock bolts and cable bolts:steel rebars,smooth steel bars,fiberglass reinforced polymer threaded bolts,flexible cable bolts,IR5/IN special cable bolts and Mini-cage cable bolts.The diameter of the tested bolts was between 16 mm and 26 mm.The bolts were grouted in a sandstone sample using resin or cement grouts.The tests were conducted under either constant radial stiffness or constant confining pressure boundary conditions applied on the outer surface of the rock sample.In most tests,the rate of displacement was about 0.02 mm/s.The tests were performed using a pull-out bench that allows testing a wide range of parameters.This paper provides an extensive database of laboratory pull-out test results and confirms the influence of the confining pressure and the embedment length on the pull-out response(rock bolts and cable bolts).It also highlights the sensitivity of the results to the operating conditions and to the behavior of the sample as a whole,which cannot be neglected when the test results are used to assess the bolt-grout or the grouterock interface.

Acoustic emission characterization of microcracking in laboratory-scale hydraulic fracturing tests

Understanding microcracking near coalesced fracture generation is critically important for hydrocarbon and geothermal reservoir characterization as well as damage evaluation in civil engineering structures. Dense and sometimes random microcracking near coalesced fracture formation alters the mechanical properties of the nearby virgin material. Individual microcrack characterization is also significant in quantifying the material changes near the fracture faces （i.e. damage）. Acoustic emission （AE） monitoring and analysis provide unique information regarding the microcracking process temporally, and infor- mation concerning the source characterization of individual microcracks can be extracted. In this context, laboratory hydraulic fracture tests were carried out while monitoring the AEs from several piezoelectric transducers. In-depth post-processing of the AE event data was performed for the purpose of under- standing the individual source mechanisms. Several source characterization techniques including moment tensor inversion, event parametric analysis, and volumetric deformation analysis were adopted. Post-test fracture characterization through coring, slicing and micro-computed tomographic imaging was performed to determine the coalesced fracture location and structure. Distinct differences in fracture characteristics were found spatially in relation to the openhole injection interval. Individual microcrack AE analysis showed substantial energy reduction emanating spatially from the injection interval. It was quantitatively observed that the recorded AE signals provided sufficient information to generalize the damage radiating spatially away from the injection wellbore.

From bed to bench: Which attitude towards the laboratoryliver tests should health care practitioners strike?

There is a general consensus in re-interpreting the so-called liver function tests in the light of novel discoveries. At the same time, recent evidence favours the use of different laboratory data to assess liver damage, fibrosis or regenerative process, but this point is not always shared. Actually, balancing the need for diagnosis, prognostic evaluation and therapy response of liver disease with a good cost/benefit ratio is very difficult. New tests are probably not needed but the aim should be for better utilization of existing tests to contain the increasing cost of health care.

AN APPLICATION OF LABVIEW ON AUTOMATIC DATA ACQUISITION AND CONTROL IN GEOTECHNICAL LABORATORY TESTS

The characteristics of USB data acquisition system NI cDAQ and its control software LabVIEW are briefed.The methods for controlling GDS pressure and volume controller by LabVIEW through serial port communication are presented.A practical data sharing method among geotechnical testing systems is illustrated.As an application case on a modified conventional soil triaxial testing system, the automatic triaxial testing system is designed by LabVIEW.Based on the control panel, the cell pressure and back pressure can be controlled independently and the testing data can be recorded automatically.

Alterations in the Results of Biochemical Laboratory Tests Due to the Administration of Antihypertensive Drugs

Objective:Perform a literary review of the interference in the results of biochemical laboratory tests caused by antihypertensive drugs.Methods:This is a review of the scientific literature with descriptive research performed according to the PRISMA model using the databases PUBMED,SCIELO,MEDLINE,LILACS,and searches of Brazilian Ministry of Health and Federal Pharmacy Council publications,reagent kits and package inserts approved by ANVISA.Literature and papers in Portuguese and English were selected,prioritizing the years 2010 to 2020.Results:The diuretic class of antihypertensive drugs causes decreases glucose tolerance,thus resulting in an increase in triglycerides.In long-term use,the drug captopril can increase serum levels of potassium,creatine kinase and decreases blood sodium.Methyldopa causes an increase in AST levels.Propranolol is associated with an increase in triglyceride levels and a decrease in HDL and glucose levels.The constant use of losartan results in an increase in HDL,a decrease in uric acid levels and a slight and transient increase in transaminases.In the Gold Analisa,Bioclin and Labtest reagent kits,most of the alterations occur due to the increase in levels of serum biomarkers according to the class of the antihypertensive drug.Conclusions:Biochemical alterations in serum can result in false-positive or false-negative reports,since it can be observed that most of the dosages caused increases due to the physiological effect of the drugs.The antihypertensive drugs that showed the highest incidence of interference were captopril,atenolol,losartan and propranolol.

Comparison of Final Drive GearLubricant Field Results to Laboratory Tests

To meet the increasing needs to move goods and materials, transportation vehicles are logging an increasing number of kilometers each year. With increasing use of these vehicles comes the need to conserve fuel to save money and to conserve resources. New engines, transmissions and axles are being developed to further conserve fuel and to provide more efficient power sources. Southwest Research Institute, a leader in global automotive research, regularly performs tests to evaluate the power and fuel economy improvement of drive train hardware and lubricants. The Institute has recently provided services to design, develop, and perform test verification of a dynamometer stand that is capable of evaluating the efficiency of axle lubricants in heavy-duty use.

The Transformer Short-Circuit Test and the High Power Laboratory in China-the Past,Present,and Future

We review the short-circuit testing of distribution and power transformers, and include a list of 110-220kV power transformers tested up to February 2002.

Research on in-situ condition preserved coring and testing systems

As shallow resources are increasingly depleted,the mechanics'theory and testing technology of deep insitu rock has become urgent.Traditional coring technologies obtain rock samples without retaining the in-situ environmental conditions,leading to distortion of the measured parameters.Herein,a coring and testing systems retaining in-situ geological conditions is presented:the coring system that obtains in-situ rock samples,and the transfer and testing system that stores and analyzes the rocks under a reconstructed environment.The ICP-Coring system mainly consists of the pressure controller,active insulated core reactor and insulation layer and sealing film.The ultimate bearing strength of 100 MPa for pressurepreservation,temperature control accuracy of 0.97%for temperature-retained are realized.CH_(4)and CO permeability of the optimized sealing film are as low as 3.85 and 0.33 ppm/min.The average tensile elongation of the film is 152.4%and the light transmittance is reduced to 0%.Additionally,the pressure and steady-state temperature accuracy for reconstructing the in-situ environment of transfer and storage system up to 1%and±0.2 is achieved.The error recorded of the noncontact sensor ring made of lowdensity polymer is less than 6%than that of the contact test.The system can provide technical support for the deep in-situ rock mechanics research,improving deep resource acquisition capabilities and further clarifying deep-earth processes.

Assessment of rapid impact compaction in ground improvement from in-situ testing

Ground improvement has been used on many construction sites to densify granular materials, in other word, to improve soil properties and reduce potential settlement. This work presents a case study of ground improvement using rapid impact compaction （RIC）. The research site comprises the construction of workshop and depots as part of railway development project at Batu Gajah-Ipoh, Malaysia. In-situ testing results show that the subsurface soil comprises mainly of sand and silty sand through the investigated depth extended to 10 m. Groundwater is approximately 0.5 m below the ground surface. Evaluation of improvement was based on the results of pre- and post-improvement cone penetration test （CPT）. Interpretation software has been used to infer soil properties. Load test was conducted to estimate soil settlement. It is found that the technique succeeds in improving soil properties namely the relative density increases from 45% to 70%, the friction angle of soil is increased by an average of 3°, and the soil settlement is reduced by 50%： The technique succeeds in improving soil properties to approximately 5.0 m in depth depending on soil uniformity with depth.

In-Situ Test on Fatigue Characteristics of Top-Mounted Dividable Pile-Board Subgrade for High-Speed Railway

To simulate the fatigue characteristics of the pile-board structure under long-term dynamic load, using the in-situ dynamic testing system DTS-1, the forced vibration loading was repeated one million times at different cross-sections of the pile-board structure for high-speed railway. The dynamic deformation, permanent deformation and dynamic stress of main reinforcements were measured. The test results show that the dynamic responses of the pile-board structure almost did not vary with the forced vibration times under the simulated trainload. After one million times of forced vibration, the permanent deformations of the midspan section of intermediate span and midspan section of side span were 0.7 mm and 0. 6 mm, respectively, and there was no accumulative plastic deformation at the bearing section of intermediate span.

Laboratory Test on Volumetric Characteristics of Saturated Sea Sand Under Cyclic Loading

The deformation of sea coast or sandy deposits caused by earthquakes can lead to catastrophic damages to various port structures. The volumetric deformation is mainly induced by densification of sand during the dissipation of excess pore water pressure created by cyclic loading. Based on laboratory test, the reconsolidation volumetric characteristics of saturated sea sand are investigated. The experiments are conducted with a newly developed multi functional triaxial test equipment. Two types of dynamic loads are applied to the samples to clarify different kinds of affecting factors. It is found that the reconsolidation volumetric strain is correlated not only to the excess pore water pressure and the maximum shear strain during the dynamic loading, but also to the effective confining pressure. A new formula is put forward to calculate the volumetric strain during reconssolidation.

Clinical Diagnosis and Treatment Characteristics of Acute Respiratory Infections in Children and New Developments in Laboratory Testing

Acute respiratory tract infection (ARTI) in children is the most common infectious disease in childhood, and its pathogens include viruses, bacteria and fungi, mycoplasma, chlamydia and rickettsia. In recent years, with the continuous development of pathogen detection methods, the diagnosis and treatment of acute respiratory infections has received more and more clinical attention. The clinical diagnosis and treatment characteristics of acute respiratory infections in children and the research of clinical laboratory detection methods have also been continuously developed. The author collected references to review the clinical features and new developments in laboratory testing of acute respiratory tract infection in children.

Mode Innovation of School-Enterprise Cooperation on Food Safety Testing Laboratory Reform

In view of the difficulties about school-enterprise cooperation on food safety testing laboratory reform,the current training program,teaching methods and teaching forms are not suitable for the new platform.This paper provides new ideas and modes to solve these problems,such as integrating the resource elements between school and enterprise,establishing new platforms with the help of external force and innovating the cooperation modes to improve the laboratory,which can fully serve teaching,scientific research and enterprise production.

Research progress and application of deep in-situ condition preserved coring and testing

With the depletion of shallow resources,the exploration of deep earth resources has become a global strategy.The study of the different patterns in the physical mechanical properties of rocks at different occurrence depths is the basis for exploring deep into the earth,with the core and premise being the acquisition and testing of deep in-situ core specimens.Based on the original idea of deep in-situ condition preserved coring(ICP-Coring)and testing,combined with theoretical modeling,numerical analysis,test platform development,indoor testing and engineering application,the principles and technologies of deep ICP-Coring are developed.This principle and technology consists of five parts:in-situ pressurepreserved coring(IPP-Coring),in-situ substance-preserved coring(ISP-Coring),in-situ temperaturepreserved coring(ITP-Coring),in-situ light-preserved coring(ILP-Coring),and in-situ moisturepreserved coring(IMP-Coring).The theory and technology of temperature and pressure reconstruction at different occurrence depths and in different environments are proposed,and prototype trial production was completed by following the principle of displacement and tests based on the in-situ reconstructed environment.The notable advances are as follows:(1)Deep in-situ coring system:A pressure-preserved controller with an ultimate bearing capacity greater than 140 MPa,highperformance(temperature-resistant,pressure-resistant,and low thermally conductive)temperaturepreserved materials,an active temperature control system,and high-barrier quality-preserved membrane materials were developed;a deep ICP-Coring capacity calibration platform was independently developed,a deep in-situ coring technology system was developed,and the acquisition of deep in-situ cores was realized.(2)In-situ storage displacement system:Following the dual-circuit hydraulic design idea,a single-drive source push-pull composite grabbing mechanism was designed;the design of the overall structure for the deep in-situ displacement storage system and ultrahigh pressure cabin structure was completed,which could realize docking the coring device and core displacement in the in-situ reconstructed environment.(3)Test analysis system:A noncontact acoustic-electric-magnetic test system was developed under the in-situ reconstructed environment,and the errors between the test results and traditional contact test results were mostly less than 10%;a detachable deep in-situ core true triaxial test system was developed,which could perform loading tests for deep in-situ cores.The relevant technological achievements were successfully applied to the exploration and development of deep resources,such as deep mines,deep-sea natural gas hydrates,and deep oil and gas.The research results provide technical and equipment support for the construction of a theoretical system for deep in-situ rock mechanics,the development of deep earth resources and energy,and the scientific exploration of different layers and occurrence depths(deep and ultradeep)of the Earth.

Effects of temperature and wavelength choice on in-situ dissolution test of Cimetidine tablets

The effects of temperature and wavelength choice on in-situ dissolution test instrument of Cimetidine were studied. Absorbance （A）〈 1.0 is required when using a fiber-optic dissolution test system. The detection wavelength of 2 （218 nm） was replaced by 244 nm to carry out this test. The absorbance of Cimetidine solution at different temperature showed an obvious change. Calibration of Cimetidine solution should be tested at the same temperature （37° C） with the test solution. A suitable wavelength with smaller tangent slope could be chosen for in-situ dissolution test of Cimetidine tablets.

Engineering behaviors of reinforced gabion retaining wall based on laboratory test

In order to study the engineering behaviors of reinforced gabion retaining wall,laboratory model test was carried out.Cyclic load and unload of five levels(0-50,0-100,0-50,0-200 and 0-250 kPa) were imposed.Vertical earth pressure,lateral earth pressure,deformation behaviors of reinforcements,potential failure surface and deformation behaviors of wall face were studied.Results show that vertical earth pressure is less than theoretical value,the ratio of vertical earth pressure to theoretical value increases nearly linearly with increasing load,and the correlation coefficient of regression equation is 0.92 for the second layer and 0.79 for the fifth layer.The distribution of lateral earth pressure along the wall back is nonlinear and it is less than theoretical value especially when the load imposed at the top of retaining wall is large.Therefore,reinforced gabion retaining wall will be in great safety when current method is adopted.The deformation behaviors of reinforcements both in the third layer and the fifth layer are single-peak distributions,and the position of the maximum strain is behind that determined by 0.3H(Here H refers to the height of retaining wall) method or Rankine theory.Lateral deformation of wall face increases with increasing load,and the largest lateral deformation occurs in the fourth layer,which lead to a bulging in the middle of wall face.

Characterization of microstructure and strain response in Ti-6Al-4V plasma welding deposited material by combined EBSD and in-situ tensile test

Additive layer manufacturing （ALM） of aerospace grade titanium components shows great promise in supplying a cost-effective alternative to the conventional production routes. Complex microstructures comprised of columnar remnants of directionally solidifiedβ-grains, with interior inhabited by colonies of finerα-plate structures, were found in samples produced by layered plasma welding of Ti-6Al-4V alloy. The application of in-situ tensile tests combined with rapid offline electron backscatter diffraction （EBSD） analysis provides a powerful tool for understanding and drawing qualitative correlations between microstructural features and deformation characteristics. Non-uniform deformation occurs due to a strong variation in strain response between colonies and across columnar grain boundaries. Prismatic and basal slip systems are active, with the prismatic systems contributing to the most severe deformation through coarse and widely spaced slip lines. Certain colonies behave as microstructural units, with easy slip transmission across the entire colony. Other regions exhibit significant deformation mismatch, with local build-up of strain gradients and stress concentration. The segmentation occurs due to the growth morphology and variant constraints imposed by the columnar solidification structures through orientation relationships, interface alignment and preferred growth directions. Tensile tests perpendicular to columnar structures reveal deformation localization at columnar grain boundaries. In this work connections are made between the theoretical macro- and microstructural growth mechanisms and the observed microstructure of the Ti-6Al-4V alloy, which in turn is linked to observations during in-situ tensile tests.

Research of in-situ hydraulic test method by using double packer equipment

Double packer equipment for hydraulic test can be used to measure pressure of test zone directly, and it is frequently used to perform many kinds of hydraulic tests and take groundwater sample from borehole. The test method of this equipment mainly includes the test design, implementation, interpretation and synthetic analysis. By adopting the double packer equipment for hydraulic test, the parameter distribution of rock permeability along borehole can be acquired, as well as the connectivity, water conductivity and water bearing capacity of the disclosed structure and the chemical characteristics of the deep groundwater. It is a necessary method for the research and evaluation of the complex hypotonicity terrace site selection under geological conditions. This method is not only suitable for the geological disposal of high level radioactive waste, but also can be used in the site selection of underground facilities such as storage of petroleum and carbon dioxide. Meanwhile, it has a good application prospect in other hydrogeological investigation fields.