Thin-walled and large-sized magnesium alloy die castings for passenger car cockpit:Application,materials,and manufacture

In order to effectively reduce energy consumption and increase range mile,new energy vehicles represented by Tesla have greatly aroused the application of integrated magnesium(Mg)alloy die casting technology in automobiles.Previously,the application of Mg alloys in automobiles,especially in automotive cockpit components,is quite extensive,while it has almost disappeared for a period of time due to its relatively high cost,causing a certain degree of information loss in the application technology of Mg alloy parts in automobiles.The rapid development of automotive technology has led to a higher requirement for the automotive components compared with those traditional one.Therefore,whatever the components themselves,or the Mg alloy materials and die casting process have to face an increasing challenge,needing to be upgraded.In addition,owing to its high integration characteristics,the application of Mg alloy die casting technology in large-sized and thin-walled automotive parts has inherent advantages and needs to be expanded urgently.Indeed,it necessitates exploring advance Mg alloys and new product structures and optimizing die casting processes.This article summarizes and analyzes the development status of thin-walled and large-sized die casting Mg alloy parts in passenger car cockpit and corresponding material selection methods,die casting processes as well as mold design techniques.Furthermore,this work will aid researchers in establishing a comprehensive understanding of the manufacture of thin-walled and large-sized die casting Mg alloy parts in automobile cockpit.It will also assist them in developing new Mg alloys with improved comprehensive performance and new processes to meet the high requirements for die casting automotive components.

Large Eddy Simulation of Vertical Structure and Size Density of Deep Layer Clouds

In a convective scheme featuring a discretized cloud size density, the assumed lateral mixing rate is inversely proportional to the exponential coefficient of plume size. This follows a typical assumption of-1, but it has unveiled inherent uncertainties, especially for deep layer clouds. Addressing this knowledge gap, we conducted comprehensive large eddy simulations and comparative analyses focused on terrestrial regions. Our investigation revealed that cloud formation adheres to the tenets of Bernoulli trials, illustrating power-law scaling that remains consistent regardless of the inherent deep layer cloud attributes existing between cloud size and the number of clouds. This scaling paradigm encompasses liquid, ice, and mixed phases in deep layer clouds. The exponent characterizing the interplay between cloud scale and number in the deep layer cloud, specifically for liquid, ice, or mixed-phase clouds, resembles that of shallow convection,but converges closely to zero. This convergence signifies a propensity for diminished cloud numbers and sizes within deep layer clouds. Notably, the infusion of abundant moisture and the release of latent heat by condensation within the lower atmospheric strata make substantial contributions. However, this role in ice phase formation is limited. The emergence of liquid and ice phases in deep layer clouds is facilitated by the latent heat and influenced by the wind shear inherent in the middle levels. These interrelationships hold potential applications in formulating parameterizations and post-processing model outcomes.

Combining prognostic value of serum carbohydrate antigen 19-9 and tumor size reduction ratio in pancreatic ductal adenocarcinoma

BACKGROUND Pancreatic ductal adenocarcinoma(PDAC)is a common cancer with increasing morbidity and mortality due to changes of social environment.AIM To evaluate the significance of serum carbohydrate antigen 19-9(CA19-9)and tumor size changes pre-and post-neoadjuvant therapy(NAT).METHODS This retrospective study was conducted at the Chongqing Key Laboratory of Translational Research for Cancer Metastasis and Individualized Treatment,Chongqing University Cancer Hospital.This study specifically assessed CA19-9 levels and tumor size before and after NAT.RESULTS A total of 156 patients who completed NAT and subsequently underwent tumor resection were included in this study.The average age was 65.4±10.6 years and 72(46.2%)patients were female.Before survival analysis,we defined the post-NAT serum CA19-9 level/pre-NAT serum CA19-9 level as the CA19-9 ratio(CR).The patients were divided into three groups:CR<0.5,CR>0.5 and<1 and CR>1.With regard to tumor size measured by both computed tomography and magnetic resonance imaging,we defined the post-NAT tumor size/pre-NAT tumor size as the tumor size ratio(TR).The patients were then divided into three groups:TR<0.5,TR>0.5 and<1 and TR>1.Based on these groups divided according to CR and TR,we performed both overall survival(OS)and disease-free survival(DFS)analyses.Log-rank tests showed that both OS and DFS were significantly different among the groups according to CR and TR(P<0.05).CR and TR after NAT were associated with increased odds of achieving a complete or near-complete pathologic response.Moreover,CR(hazard ratio:1.721,95%CI:1.373-3.762;P=0.006),and TR(hazard ratio:1.435,95%CI:1.275-4.363;P=0.014)were identified as independent factors associated with OS.CONCLUSION This study demonstrated that post-NAT serum CA19-9 level/pre-NAT serum CA19-9 level and post-NAT tumor size/pre-NAT tumor size were independent factors associated with OS in patients with PDAC who received NAT and subsequent surgical resection.

Preparation of crystalline rare earth carbonates with large particle size from the lixivium of weathered crust elution-deposited rare earth ores

Crystalline rare-earth(RE)carbonates having large particle size were prepared from the lixivium of weathered crust elution-deposited rare-earth ores using the precipitation method with ammonium bicarbonate as the precipitant.Their chemical composition was studied using elemental and thermogravimetric analyses(TGA),and their structure and morphology were characterized using Fourier transform infrared(FTIR)spectroscopy,X-ray diffraction(XRD),and scanning electron microscopy(SEM).The results demonstrate that the crystalline rareearth carbonate is a hydrated basic carbonate or oxycarbonate and not astable intermediate carbonate in the process of thermal decomposition.The particle size of crystalline rare-earth carbonates with large particle size is in the range of 50–200μm.With an RE2O3 content of up to 95wt%,the quality of crystalline rare-earth carbonates is higher compared to the Chinese National Standard(GB/T 28882–2012).The quality of the product is superior to the Chinese National Standard.

Effect of Temperature and Ram Speed on Isothermal Extrusion for Large-size Tube with Piece-wing

Heat energy change during the extrusion of 7075 aluminium alloy large-size tube with piece-wing in a container was analyzed. Extrusion load vs ram displacement diagrams and exit temperature vs ram displacement diagrams at various speeds were obtained by 3D FEM simulation. Results show that the exit temperature becomes higher as the ram speed and displacement increase. For large-size tube with piece-wing, there is certainly a curve of ram speed decreasing with increasing ram displacement, which enables isothermal extrusion to be achieved. Therefore,an attempt was made to divide the working stroke into five different zones. Each of them has a preset speed that decreases from the ram displacement beginning to the ending. And then, new exit temperature vs ram displacement diagram was obtained by 3D FEM simulation for the five different speeds. It is shown that the variation of exit temperature is very small. Through the above research, a basic method for realizing isothermal extrusion of 7075 large-size tube with piece-wing was obtained, that is, the working stroke was divided into several different zones with a decreasing speed during extrusion, each zonest speed was real-time adjusted on the feedback signal of exit temperature by proportional hydraulic valve through closed-loop control. The engineering experiment verification was carried out on 100 MN aluminium extrusion press with oil-driven double action. The experimental results of the exit temperature agrees with the simulation ones. The achievements of this study may serve as a significant guide to the practice of the relevant processes, particularly for isothermal extrusion. The verified method has been used in the design and manufacture of 125 MN aluminium extrusion press with oil-driven double action.

Parallel algorithm of solidification process simulation for large-sized system of liquid metal atoms

A parallel arithmetic program for the molecular dynamics (MD) simulation study of a large sized system consisting of 50 000100 000 atoms of liquid metals is reformed, based on the cascade arithmetic program used for the molecular dynamics simulation study of a small sized system consisting of 5001 000 atoms. The program is used to simulate the rapid solidification processes of liquid metal Al system. Some new results, such as larger clusters composed of more than 36 smaller clusters (icosahedra or defect icosahedra) obtained in the system of 50 000 atoms, however, the larger clusters can not be seen in the small sized system of 5001 000 atoms. On the other hand, the results from this simulation study would be more closed to the real situation of the system under consideration because the influence of boundary conditions is decreased remarkably. It can be expected that from the parallel algorithm combined with the higher performance super computer, the total number of atoms in simulation system can be enlarged again up to tens, even hundreds times in the near future.

Study on Factors Influencing the Reliability of the Organization Management Chain of the Large and Medium-Sized Project in the Construction Period

On the basis of analyzing the reliability of the organization’ management chain of the large and medium- sized project in the construction period, the paper studies the factors influencing the reliability of the organi-zation management chain, which, corresponding to four elements of management chain – “Management Loop”, “Management Link”, “Management Chain”, and “Management Network”, can be summarized as project main body, interface management, connection sequence and management model. The paper then re-searches on the specific influencing factors from the above-mentioned four aspects.

Study on scour around vertical large-size cylinder base due to combined action of wave and current

Based on the mechanism of local scour around vertical large-sized cylinder due to combined action of wave and current,the sour morphology,scour process and the maximum scour depth around the cylinders are studied experimentally.The influence of various ocean environmental parameters on local scour around the cylinder is considered in physical model test.The experimental results indicate that the principal effect factors on the scour in fine-sand seabed are wave height,wavelength,current velocity,ratio of diameter to wavelength and ratio of depth to wavelength when the ratio of cylinder diameter to wavelength is from 0.2 to 0.8.In this paper,dimensional analysis theory is utilized to establish a theoretical equation for forecasting maximum scour depth around large-sized round cylinder base due to the combined action of wave and current.The results computed with the theoretical equation are compared with the experimental results,and found to be in good consistency.The results in this studies can be used to estimate the maximum sour depth around analogous structures.

Precise large deviations for sums of random vectors in a multidimensional size-dependent renewal risk model

Consider a multidimensional renewal risk model, in which the claim sizes {Xk, k ≥1} form a sequence of independent and identically distributed random vectors with nonnegative components that are allowed to be dependent on each other. The univariate marginal distributions of these vectors have consistently varying tails and finite means. Suppose that the claim sizes and inter-arrival times correspondingly form a sequence of independent and identically distributed random pairs, with each pair obeying a dependence structure. A precise large deviation for the multidimensional renewal risk model is obtained.

Modeling and simulation of 3D thermal stresses of large-sized castings in solidification processes

When heavy machines and large scaled receiver system of communication equipment are manufactured, it always needs to produce large-sized steel castings, aluminum castings and etc. Some defects of hot cracking by thermal stress often appear during solidification process as these castings are produced, which results in failure of castings. Therefore predicting the effects of technological parameters for production of castings on the thermal stress during solidification process becomes an important means. In this paper, the mathematical models have been established and numerical calculation of temperature fields by using finite difference method (FDM) and then thermal stress fields by using finite element method (FEM) during solidification process of castings have been carried out. The technological parameters of production have been optimized by the results of calculation and the defects of hot cracking have been eliminated. Modeling and simulation of 3D thermal stress during solidification processes of large-sized castings provided a scientific basis, which promoted further development of advanced manufacturing technique.

Rolling Fatigue Test of Large-Sized UHPC Member for Cable Stayed Bridge

Recently, research strives to apply Ultra High Performance Concrete (UHPC) to large-sized structures owing to its remarkable mechanical performance and durability compared to normal concrete. The Korea Institute of Construction Technology proposed SuperBridge800, an edge girder type UHPC cable stayed bridge with central span of 800 m, through its detailed design. The bridge is designed to be erected through the connection of precast UHPC segments. The precast UHPC segment is monolithically composed of one ribbed deck slab and edge girders at each side. The connection between the precast segments is achieved by steel bars at the edge girders and by UHPC cast-in-place wet joint at the slab. Despite of the outstanding mechanical performance of UHPC, the fabrication of large-sized members is a difficult task since UHPC hardens faster than normal concrete and requires a special curing process. Therefore, the constructability of large-sized UHPC segment should be secured to achieve SuperBridge800. Besides, the performance of the connection between segments should also be guaranteed, especially in terms of the fatigue performance of the UHPC cast-in-place joint, which constitutes a weak point. To that goal, two half-scaled UHPC segments are manufactured and the constructability is examined by fabricating a large-sized UHPC member connected with respect to the design conditions. This study conducts rolling fatigue test on the so-fabricated large-sized UHPC member. Rolling fatigue test is carried out up to 2 million cycles considering actual vehicle load at each center and quarter points of the member. The test results confirm that the service limit state is satisfied.

Distribution and exploration direction of medium-and large-sized marine carbonate gas fields in Sichuan Basin, SW China

Based on the analysis of the basic characteristics of medium-and large-sized marine gas fields in Sichuan Basin, combined with the division of major reservoir forming geological units in the marine craton stage and their control on key hydrocarbon accumulation factors, the distribution law of medium-and large-sized marine carbonate gas fields in the basin was examined and the exploration direction was pointed out. Through the analysis of the periodic stretching-uplifting background, it is concluded that five large scale paleo-rifts, three large scale paleo-uplifts, five large scale paleo erosion surfaces were formed in the marine craton stage of Sichuan Basin, and these geological units control the key reservoir forming factors of medium and large sized gas fields:(1) Large-scale paleo-rifts control the distribution of high-quality hydrocarbon generation centers.(2) The margin of large-scale paleo-rifts, high position of paleo-uplifts and paleo erosion surfaces control the distribution of high-quality reservoirs.(3) Large-scale paleo-rifts, paleo-uplifts, paleo erosion surfaces and present tectonic setting jointly control the formation of many types of large and medium-sized traps.(4) Natural gas accumulation is controlled by the inheritance evolution of traps in large geological units. Based on the comparative analysis of the distribution characteristics of medium-and large-sized gas fields and large geological units, it is proposed that the superimposition relationship between single or multiple geological units and the present structure controls the distribution of medium-and large-sized gas fields, and the "three paleo" superimposed area is the most advantageous. According to the above rules, the main exploration fields and directions of medium-and large-sized marine carbonate gas fields in Sichuan Basin include periphery of Deyang-Anyue paleo-rift, eastern margin of Longmenshan paleo-rift, margins of Kaijiang-Liangping oceanic trough and Chengkou-western Hubei oceanic trough, the high part of the subaqueous paleo-uplifts around Central Sichuan, paleo erosion surfaces of the top boundary of Maokou Formation in eastern and southern Sichuan Basin, paleo erosion surfaces of the top boundary of the Leikoupo Formation in central and western Sichuan Basin.

Experimental investigation and numerical simulation of large-sized aluminum tube extrusion forming

Large-sized aluminum tube has big section effect, aspect ratio and thin thickness, so that the extrusion technology is complex and the large specific pressure is generated in extrusion cavity. The temperature variation and velocity effect is difficult to control. The extrusion forming of large-sized aluminum tube was researched and simulated. Three-dimensional thermo-mechanical coupled finite element model was constructed and appropriate boundary conditions were given out. The results show that large-sized aluminum tube can be formed by isothermal extrusion through controlling the extrusion velocity and founding the relationship between extrusion velocity and extrusion temperature.

Computer Simulation of the Process of Quenching Large-Size Parts in Water and Aqueous Solutions

The article presents results of the computer simulation of quenching large-size parts in water and aqueous solutions. It has been shown that the main attention should be paid to eliminating film boiling and providing uniform cooling at the surface of the part to be quenched. Simplified formulas for calculating the optimal time of cooling large-size steel parts are presented.

Retrospect and Prospect of Excitation Systems of Large Size Turbogenerators

This paper briefs the developmental course, manufacturing and applications, as well as future prospect of excitation systems of large size turbogenerators in China, emphatically expounds the advantages of seif-excitation systems with potential source reetifiers and matters needing to be noted during dissemination and application of them.

Cerium dioxide with large particle size prepared by continuous precipitation

Cerium dioxide(CeO2) has attracted much attention and has wide applications such as automotive exhaust catalysts,polishing materials for optical glasses and additives for advanced glasses,as well as cosmetic materials.The particle size and its distribution are key factors to the performance of the materials in the functional applications.However,control of particle size is still a challenge in materials synthesis.Therefore,continuous precipitation of cerium oxalate(precursor of ceria) was carried out at dif...

Key technologies and equipment for a fully mechanized top-coal caving operation with a large mining height at ultra-thick coal seams

Thick and ultra-thick coal seams are main coal seams for high production rate and high efficiency in Chinese coal mines, which accounts for 44 % of the total minable coal reserve. A fully mechanized top-coal caving mining method is a main underground coal extraction method for ultra-thick coal seams. The coal extraction technologies for coal seams less than 14 m thick were extensively used in China. However, for coal seams with thickness greater than 14 m, there have been no reported cases in the world for underground mechanical extraction with safe performance, high efficiency and high coal recovery ratio. To deal with this case, China Coal Technology ＆ Engineering Group, Datong Coal Mine Group, and other 15 organizations in China launched a fundamental and big project to develop coal mining technologies and equipment for coal seams with thicknesses greater than 14 m. After the completion of the project, a coal extraction method was developed for top-coal caving with a large mining height, as well as a ground control theory for ultra-thick coal seams. In addition, the mining technology for top-coal caving with a large mining height, the ground support technology for roadway in coal seams with a large cross-section, and the prevention and control technology for gas and fire hazards were developed and applied. Furthermore, a hydraulic support with a mining height of 5.2 m, a shearer with high reliability, and auxiliary equipment were developed and manufactured. Practical implication on the technologies and equipment developed was successfully completed at the No. 8105 coal face in the Tashan coal mine, Datong, China. The major achievements of the project are summarized as follows： 1. A top-coal caving method for ultra-thick coal seams is proposed with a cutting height of 5 m and a top-coal caving height of 15 m. A structural mechanical model of overlying strata called cantilever beam-articulated rock beam is established. Based on the model, the load resistance of the hydraulic support with a large mining height for top-coal caving method is determined. With the analysis, the movement characteristics of the top coal and above strata are evaluated during top-coal caving operation at the coal face with a large mining height. Furthermore, there is successful development of comprehensive technologies for preventing and controlling spalling of the coal wall, and the top-coal caving technology with high efficiency and high recovery at the top-coal caving face with a large mining height. This means that the technologies developed have overcome the difficulties in strata control, top-coal caving with high efficiency and high coal recovery, and enabled to achieve a production rate of more than 10 Mtpa at a single top-coal caving face with a large mining height in ultra-thick coal seams; 2. A hydraulic support with 5.2 m supporting height and anti-rockburst capacity, a shearer with high reliability, a scraper conveyor with a large power at the back of face, and a large load and long distance headgate belt conveyor have been successfully developed for a top-coal caving face with large mining height. The study has developed the key technologies for improving the reliability of equipment at the coal face and has overcome the challenges in equipping the top-coal caving face with a large mining height in ultra-thick coal seams; 3. The deformation characteristics of a large cross-section roadway in ultra-thick coal seams are discovered. Based on the findings above, a series of bolt materials with a high yielding strength of 500-830 MPa and a high extension ratio, and cable bolt material with a 1 × 19 structure, large tonnage and high extension ratio are developed. In addition, in order to achieve a safe roadway and a fast face advance, installation equipment for high pre-tension bolt is developed to solve the problems with the support of roadway in coal seams for top-coal caving operation with a large mining height; 4. The characteristics of gas distribution and uneven emission at top-coal caving face with large mining height in ultra-thick coal seams are evaluated. With the application of the technologies of gas drainage in the roof, the difficulties in gas control for high intensive top-coal caving mining operations, known as ＂low gas content, high gas emission＂, are solved. In addition, large flow-rate underground mobile equipment for making nitrogen are developed to solve the problems with fire prevention and safe mining at a top-coal caving face with large mining height and production rate of more than 10 Mtpa. A case study to apply the developed technologies has been conducted at the No. 8105 face, the Tashan coal mine in Datong, China. The case study demonstrates that the three units of equipment, i.e., the support, shearer and scraper conveyor, are rationally equipped. Average equipment usage at the coal face is 92.1%. The coal recovery ratio at the coal face is up to 88.9 %. In 2011, the coal production at the No. 8105 face reached 10.849 Mtpa, exceeding the target of 10 Mtpa for a topcoal caving operation with large mining height performed by Chinese-made mining equipment. The technologies and equipment developed provide a way for extracting ultra-thick coal seams. Currently, the technologies and equipment are used in 13 mining areas in China including Datong, Pingshuo, Shendong and Xinjiang. With the exploitation of coal resources in Western China, there is great potential for the application of the technologies and equipment developed.

miR-23a/27a/24基因簇g.65307469G>A突变对大白猪产仔数和启动子活性的影响

[目的]本文旨在研究大白猪miR-23a/27a/24基因簇启动子突变位点多态性与产仔数性状的关系及潜在机制,为母猪繁殖性状的分子育种提供新的潜在遗传标记。[方法]利用混池测序技术筛选猪miR-23a/27a/24基因簇启动子突变位点,直接测序法对大白猪群体(n=345)miR-23a/27a/24基因簇突变位点进行基因分型,计算遗传多样性;用线性模型对突变位点多态性与产仔数性状进行关联性分析;构建不同等位基因类型启动子载体,转染猪卵巢颗粒细胞,通过检测荧光素酶活性分析突变对启动子活性的影响;用生物信息学方法预测不同等位基因类型启动子潜在结合的差异转录因子,用荧光素酶活性分析差异转录因子对不同等位基因类型启动子活性的影响。[结果]在猪miR-23a/27a/24基因簇启动子-648 nt(Chr.2,65307469 nt)处发现1个新的G/A突变,命名为g.65307469G>A。在大白猪群体中发现3种基因型(GG、GA和AA),其中GG为优势基因型(89.57%),G等位基因为优势等位基因(94.64%)。关联性分析发现,GA基因型母猪的总产仔数(TNB)比GG基因型母猪每胎高0.56头(P<0.05)。荧光素酶活性分析结果显示G等位基因类型启动子活性显著高于A等位基因类型(P<0.05)。在不同等位基因类型启动子间发现1个潜在结合的差异转录因子死亡相关蛋白1(THAP1),成功构建猪THAP1基因过表达载体,共转试验结果显示转录因子THAP1对不同等位基因类型启动子活性均无显著影响(P>0.05)。[结论]miR-23a、miR-27a和miR-24是大白猪产仔数性状的候选基因,g.65307469G>A突变抑制miR-23a/27a/24基因簇的启动子活性,但与转录因子THAP1无关。

Ice Resistance Assessment for a Large Size Vessel Running in a Narrow Ice Channel Behind an Icebreaker

Large size vessels sailing in continuous level ice and broken ice of high concentration are mostly assisted by icebreakers.This is done in order to provide for fast transportation through the North Sea Route and safe operation in extreme ice conditions.Currently,new large size gas and oil carriers and container ships are being designed and built with beams much greater than the beams of existing icebreakers.At the same time,no mathematical description exists for the breaking mechanism of ice channel edges,when such vessels move under icebreaker escort.This paper suggests a simple method for assessment of the ice resistance in the case of a large ship running in an icebreaker channel;the method is based on modification of well-known semi-empirical methods for calculation of the ice resistance to ships in level and broken ice.The main feature of the proposed calculation scheme consists in that different methods are applied to estimate the ice resistance in broken ice and due to breaking of level ice edges.The combination of these methods gives a deliverable ice resistance of a large size vessel moving under icebreaker assistance in a newly made ice channel.In general,proposed method allows to define the speed of a carrier moving in an ice channel behind a modern linear icebreaker and could be applied at the ship design stage and during development of the marine transportation system.The paper also discusses the ways for further refinement of the assessment procedure suggested.

Large Eddy Simulations of Flow Instabilities in a Stirred Tank Gen-erated by a Rushton Turbine

The aim of this work is to investigate the flow instabilities in a baffled, stirred tank generated by a single Rushton turbine by means of large eddy simulation （LES）. The sliding mesh method was used for the coupling between the rotating and the stationary frame of references. The calculations were carried out on the ＂Shengcao-21C＂ supercomputer using a computational fluid dynamics （CFD） code CFX5. The flow fields predicted by the LES simulation and the simulation using standard κ-ε model were compared to the results from particle image velocimetry （PIV） measurements. It is shown that the CFD simulations using the LES approach and the standard κ-ε model agree well with the PIV measurements. Fluctuations of the radial and axial velocity are predicted at different frequencies by the LES simulation. Velocity fluctuations of high frequencies are seen in the impeller region, while low frequencies velocity fluctuations are observed in the bulk flow. A low frequency velocity fluctuation with a nondimensional frequency of 0.027Hz is predicted by the LES simulation, which agrees with experimental investigations in the literature. Flow circulation patterns predicted by the LES simulation are asymmetric, stochastic and complex, spanning a large portion of the tanks and varying with time, while circulation patterns calculated by the simulation using the standard κ-ε model are symmetric. The results of the present work give better understanding to the flow instabilities in the mechanically agitated tank. However, further analysis of the LES calculated velocity series by means of fast Fourier transform （FFT） and/or spectra analysis are recommended in future work in order to gain more knowledge of the complicated flow phenomena.