A Discussion on Dynamic Characteristics of Undisturbed Loess by Dynamic Triaxial Test

Based on the dynamic triaxial test system and using the fitted wave of the Wenchuan earthquake and 1 Hz constant amplitude sinusoid,the paper compares the results of tests on undisturbed loess samples under different loads and vibration modes but under same saturated conditions.Results of the comparative experiment show:The stress-strain curves have a similar trend under random seismic loading and constant amplitude sinusoidal loading,but the random seismic loading is more sensitive to failure strength of the undisturbed loess samples under the same stress.

Dynamic behaviour of weathered red mudstone in Sichuan(China)under triaxial cyclic loading

The construction of a high-speed railway(HSR) in Southwest China is being hindered by a severe shortage of high-quality subgrade materials. However, red mudstone is widely distributed in the Sichuan Basin of China. The ability to use weathered red mudstone(WRM) to fill subgrade beds by controlling its critical stress and cumulative strain would enable substantial savings in project investments and mitigate damage to the ecological environment. To better understand the dynamic behaviour of WRM, both monotonic and cyclic triaxial tests were performed. The evolution of the cumulative strain vs. increased loading cycles was measured. The influences of confining pressure and loading cycles on the dynamic modulus, damping ratio, critical cyclic stress ratio(CSR), and dynamic stress level(DSL) were investigated. The relationship between the CSR and loading cycles under different failure strain criteria(0.1%-1.0%) was analysed. The prediction model of cumulative strain was also evaluated. The results indicated that the shear strength of WRM sufficiently meets the static strength requirements of subgrade. The critical dynamic stress of WRM can thus satisfy the dynamic stress-bearing requirement of the HSR subgrade. The critical CSR decreases and displays a power function with increasing confining pressure. As the confining pressure increases, the DSL remains relatively stable, ranging between 0.153 and 0.163. Furthermore, the relationship between the dynamic strength and loading cycles required to cause failure was established. Finally, a newly developed model for determining cumulative strain was established. A prediction exercise showed that the model is in good agreement with the experimental data.

Experimental study of the dynamic mechanical responses and failure characteristics of coal under true triaxial confinements

Investigations on the dynamic mechanical properties and failure mechanisms of coal under in-situ stress is essential for the prevention of dynamic disasters in deep coal mines.Thus,a modified true triaxial Hopkinson bar was employed to explore the dynamic mechanical behaviors of coal at different confining pressures(0–20 MPa)and strain rates(40–220 s^(-1)).The results show that the dynamic peak stress is positively correlated with lateral static pre-stressσy andσz,but negatively correlated with axial static prestressσx.At approximate strain rates,increasing the lateral static pre-stress facilitates increasing the dynamic peak stress,but the minimum lateral static pre-stress is the primary factor limiting a significant increase in dynamic peak stress of coal.Furthermore,the dynamic differential stress is linearly related to the logarithm of strain rate,and the peak strain varies linearly with strain rate.However,there is no significant correlation between confining pressure and peak strain.Moreover,X-ray CT images and photographic fracture observations of coal samples show the failure patterns under uniaxial and triaxial conditions are splitting failure and shear failure,respectively.The device provides a viable approach for fully comprehending the dynamic mechanical behaviors of rock-like material in complex stress conditions.

Dynamic failure process of expanded polystyrene particle lightweight soil under cyclic loading using discrete element method

Expanded polystyrene(EPS)particle-based lightweight soil,which is a type of lightweight filler,is mainly used in road engineering.The stability of subgrades under dynamic loading is attracting increased research attention.The traditional method for studying the dynamic strength characteristics of soils is dynamic triaxial testing,and the discrete element simulation of lightweight soils under cyclic load has rarely been considered.To study the meso-mechanisms of the dynamic failure processes of EPS particle lightweight soils,a discrete element numerical model is established using the particle flow code(PFC)software.The contact force,displacement field,and velocity field of lightweight soil under different cumulative compressive strains are studied.The results show that the hysteresis curves of lightweight soil present characteristics of strain accumulation,which reflect the cyclic effects of the dynamic load.When the confining pressure increases,the contact force of the particles also increases.The confining pressure can restrain the motion of the particle system and increase the dynamic strength of the sample.When the confining pressure is held constant,an increase in compressive strain causes minimal change in the contact force between soil particles.However,the contact force between the EPS particles decreases,and their displacement direction points vertically toward the center of the sample.Under an increase in compressive strain,the velocity direction of the particle system changes from a random distribution and points vertically toward the center of the sample.When the compressive strain is 5%,the number of particles deflected in the particle velocity direction increases significantly,and the cumulative rate of deformation in the lightweight soil accelerates.Therefore,it is feasible to use 5%compressive strain as the dynamic strength standard for lightweight soil.Discrete element methods provide a new approach toward the dynamic performance evaluation of lightweight soil subgrades.

Test on dynamic characteristics of subgrade of heavy-haul railway in cold regions

Dynamic characteristics of heavy-haul railway subgrade under vibratory loading in cold regions are investigated via low-temperature dynamie triaxial tests with multi-stage eyelic loading process. The relationship between dynamic shear stress and dynamic shear strain of frozen soil of subgrade under train loading and the influence of freezing temperatures on dynamic constitutive relation, dynamic shear modulus and damping ratio are observed in this study. Test results show that the dynamic constitutive relations of the frozen soils with different freezing temperatures comply with the hyperbolic model, in which model parameters a and b decrease with increasing freezing temperature. The dynamic shear modulus of the frozen soils decreases with increasing dynamic shear strains initially, followed by a relatively smooth attenuation tendency, whereas increases with decreasing freezing temperatures. The damping ratios decrease with decreasing freezing temperatures. Two linear functions are defined to express the linear relationships between dynamic shear modulus （damping ratio） and freezing temperature, respectively, in which corresponding linear coefficients are obtained through multiple regression analysis of test data.

NMR-based damage characterisation of backfill material in host rock under dynamic loading

It is not uncommon that backfill material used in underground mining being exposed to repetitive dynamic stresses induced by blasting operations or rockburst events. Understanding the strength and fracture evolution of backfilled stopes is critical to maintain the long-term stope stability and ensure safe mining activities. This paper aims to study the damage evolution of the backfill material and its host rock behaviour under three-dimensional(3D) dynamic loading. Using a true-triaxial testing machine, multiple samples of backfill material enclosed by country rock were fabricated and tested under various dynamic loadings with different true-triaxial confining stress conditions. In addition, the nuclear magnetic resonance(NMR) measurement was conducted on the samples before and after exerting static and dynamic loading to obtain their porosity distribution changes. The experiment results suggested that with the increase of the dynamic loading, the porosity of the backfill sample goes through a two-stage process,which shows a slightly linear decrease and then followed by an exponential increase. The research findings can help understand the damage mechanism and fracture development of backfilled stopes and its host rock in deep underground mines, which are constantly subject to the combination of 3D static confining stress and dynamic loading.

Experimental study of dynamic resilient modulus of subgrade soils under coupling of freeze–thaw cycles and dynamic load

Although the dynamic properties of subgrade soils in seasonally frozen areas have already been studied, few researchers have considered the influence of shallow groundwater during the freeze–thaw(F–T) cycles. So a multifunctional F–T cycle system was developed to imitate the groundwater recharge in the subgrade during the freezing process and a large number of dynamic triaxial experiments were conducted after the F–T cycles. Some significant factors including the F–T cycle number, compaction degree, confining pressure, cyclic deviator stress, loading frequency, and water content were investigated for the resilient modulus of soils. The experimental results indicated that the dynamic resilient modulus of the subgrade was negatively correlated with the cyclic deviator stress, F–T cycle number, and initial water content, whereas the degree of compaction, confining pressure, and loading frequency could enhance the resilient modulus. Furthermore, a modified model considering the F–T cycle number and stress state was established to predict the dynamic resilient modulus. The calculated results of this modified model were very close to the experimental results. Consequently, calculation of the resilient modulus for F–T cycles considering the dynamic load was appropriate. This study provides reference for research focusing on F–T cycles with groundwater supply and the dynamic resilient moduli of subgrade soils in seasonally frozen areas.

Dynamic properties of composite cemented clay

In this work, the dynamic properties of composite cemented clay under a wide range of strains were studied considering the effect of different mixing ratio and the change of confining pressures through dynamic triaxial test. A simple and practical method to estimate the dynamic elastic modulus and damping ratio is proposed in this paper and a related empirical normalized formula is also presented. The results provide useful guidelines for preliminary estimation of cement requirements to improve the dynamic properties of clays.

Dynamic Elastic Modulus and Damping Ratio of Lignin-Modified Loess

To effectively improve the poor engineering properties of loess and enhance its seismic performance,the industrial by-product lignin is used as a modified material.Based on lots of dynamic triaxial tests,the dynamic elastic modulus and damping ratio of lignin-modified loess were tested.The effects of lignin content on the dynamic elastic modulus and damping ratio of lignin-modified loess were analyzed.Combined with scanning electron microscopy(SEM)and X-ray diffraction(XRD),the microscopic mechanism of lignin to improve the dynamic properties of loess was studied.The results show that lignin can effectively modify the dynamic deformation of loess under dynamic load.Under the same dynamic stress condition,the dynamic strain of lignin-modified loess is smaller than compacted loess.The dynamic elastic modulus of modified loess with different lignin content are quite different,but both decrease with the increase of dynamic strain.And the dynamic elastic modulus of modified loess is greater than compacted loess.The maximum dynamic elastic modulus of modified loess with a lignin content of 1%are significantly greater than others.Under the same dynamic strain condition,the damping ratio of lignin-modified loess is smaller than compacted loess.Lignin can effectively fill loess pores and cement loess particles.Compared with compacted loess,no new mineral components are generated in the lignin-modified loess.The optimum lignin content of dynamics characteristic of modified loess is present,and the optimum lignin content is 1%.

Dynamic properties and liquefaction behaviour of cohesive soil in northeast India under staged cyclic loading

Estimation of strain-dependent dynamic soil properties, e.g. the shear modulus and damping ratio, along with the liquefaction potential parameters, is extremely important for the assessment and analysis of almost all geotechnical problems involving dynamic loading. This paper presents the dynamic properties and liquefaction behaviour of cohesive soil subjected to staged cyclic loading, which may be caused by main shocks of earthquakes preceded or followed by minor foreshocks or aftershocks, respectively. Cyclic triaxial tests were conducted on the specimens prepared at different dry densities （1.5 g/cm3 and 1.75 g/cm3） and different water contents ranging from 8% to 25%. The results indicated that the shear modulus reduction （G/Gmax） and damping ratio of the specimen remain unaffected due to the changes in the initial dry density and water content. Damping ratio is significantly affected by confining pressure, whereas G/Gmax is affected marginally. It was seen that the liquefaction criterion of cohesive soils based on single-amplitude shear strain （3.75% or the strain at which excess pore water pressure ratio becomes equal to 1, whichever is lower） depends on the initial state of soils and applied stresses. The dynamic model of the regional soil, obtained as an outcome of the cyclic triaxial tests, can be successfully used for ground response analysis of the region.

Dynamic mechanical characteristics of frozen subgrade soil subjected to freeze-thaw cycles

As a widely-applied engineering material in cold regions, the frozen subgrade soils are usually subjected to seismic loading, which are also dramatically influenced by the freeze-thaw(F-T)cycles due to the varying temperature. A series of dynamic cyclic triaxial experiments were conducted through a cryogenic triaxial apparatus for exploring the influences of F-T cycles on the dynamic mechanical properties of frozen subgrade clay.According to the experimental results of frozen clay at the temperature of-10℃, the dynamic responses and microstructure variation at different times of F-T cycles(0, 1, 5, and 20 cycles) were explored in detail.It is experimentally demonstrated that the dynamic stress-strain curves and dynamic volumetric strain curves of frozen clay are significantly sparse after 20F-T cycles. Meanwhile, the cyclic number at failure(Nf) of the frozen specimen reduces by 89% after 20freeze-thaw cycles at a low ratio of the dynamic stress amplitude. In addition, with the increasing F-T cycles,the axial accumulative strain, residual deformation,and the value of damage variable of frozen clay increase, while the dynamic resilient modulus and dynamic strength decrease. Finally, the influence of the F-T cycles on the failure mechanisms of frozen clay was discussed in terms of the microstructure variation. These studies contribute to a better understanding of the fundamental changes in the dynamic mechanical of frozen soils exposed to F-T cycles in cold and seismic regions.

Undrained dynamical behavior of Nanjing flake-shaped fine sand under cyclic loading

A series of dynamic behavior tests on Nanjing flake-shaped fine sand were performed by using the WFI cyclic triaxial apparatus made in England. The dynamic behaviors of Nanjing flake-shaped fine sand under different static deviator stress levels and cyclic stress ratios were studied. Through comparing the effective stress path under cyclic loading with static loading, the processes of liquefaction of saturated Nanjing flake-shaped fine sand with development of dynamic pore-water pressure, including the initial compact state, compression state and dilative state, were investigated. The variation of the shear stiffness with the number of cycles and cyclic strain was investigated by analyzing the secant shear modulus in each unload-reload loop of dynamic stress-strain relationship. And by means of the exponential function, the empirical equations of the relationship between secant shear modulus Gsec, shear modulus ratio Gsec/Gmax and cyclic strain ε were established based on series of test results. The results show that according to different combinations of static deviator stress and cyclic stress, two kinds of failure patterns with deviator stress reversal or no deviator stress reversal are observed in the samples tested in this series, including cyclic mobility and the failure of accumulation residual strain. In addition, the degradation of dynamic shear modulus is due to the development of vibration pore-water pressure and it is observed that the shear modulus reduces with the progressive number of cycles.

Experimental study on permanent deformation characteristics of coarse-grained soil under repeated dynamic loading

Practical assessment of subgrade settlement induced by train operation requires developing suitable models capable of describing permanent deformation characteristics of subgrade filling under repeated dynamic loading.In this paper,repeated load triaxial tests were performed on coarse-grained soil(CGS),and the axial permanent strain of CGS under different confining pressures and dynamic stress amplitudes was analysed.Permanent deformation behaviors of CGS were categorized based on the variation trend of permanent strain rate with accumulated permanent strain and the shakedown theory.A prediction model of permanent deformation considering stress state and number of load cycles was established,and the ranges of parameters for different types of dynamic behaviors were also divided.The results indicated that the variational trend of permanent strain rate with accumulated permanent strain can be used as a basis for classifying dynamic behaviors of CGS.The stress state(confining pressure and dynamic stress amplitude)has significant effects on the permanent strain rate.The accumulative characteristics of permanent deformation of CGS with the number of load cycles can be described by a power function,and the model parameters can reflect the influence of confining pressure and dynamic stress amplitude.The study’s results could help deepen understanding of the permanent deformation characteristics of CGS.

Experimental study of the dynamic behavior of high-grade highway-subgrade soil in a seasonally frozen area

Regarding the freezing damage of high-grade highway subgrade in seasonally frozen area,the thesis explores the effect on the dynamic behavior of subgrade soil under freeze–thaw cycles and draws the change law of parameters(including dynamic strength,dynamic cohesion,and internal friction angle;and dynamic elastic modulus)of high-grade highway-subgrade soil with the number of freeze–thaw cycles.It aims to provide the reference for operation and maintenance of a high-grade highway.Conclusions:(1)Dynamic strength tends to decline evidently after freeze–thaw cycles,with 60%~70%decline after three cycles,and remains stable after five to seven cycles.(2)With the number of freeze–thaw cycles increasing,the internal friction angle fluctuates within a certain range without an obvious change law,only presenting the tendency of dropping off.The dynamic cohesion declines obviously,about 20%~40%after seven freeze–thaw cycles,and then tends to be stable.(3)With the number of freeze-thaw cycles increasing,the dynamic elastic modulus and maximum dynamic elastic modulus are inclined to decrease distinctly.After five freeze–thaw cycles,the former declines 30%~40%and then remains stable.Meanwhile,the latter falls 20%~40%.

Research on damage failure mechanism and dynamic mechanical behavior of layered shale with different angles under confining pressure

The hydrostatic or confining pressure of deep rocks has a significant impact on the mechanical behavior of brittle materials.Especially when confining pressure is applied,the mechanical properties of rock materials will undergo significant changes.Considering that the process of shale sample subjected to impact load is in a closed container in the dynamic triaxial SHPB test,the failure process of the sample cannot be observed.Meanwhile,the activation volume of the shale sample would be large and local failure would occur in the test under the high strain rate loading.Therefore,thefinite element model of shale considering the bedding effect under confining pressure was established in this study.Taking shale materials with different bedding dip angles as simulation objects,the dynamic failure characteristics of shale were studied using the dynamic analysis software ANSYS/LS‐DYNA from three aspects:stress‐strain curve,failure growth process,and failure morphology.The research results obtained can serve as the key technical parameters for deep resource extraction.

细粒含量对石墨尾矿液化特性的影响

尾矿坝是一种高势能危险源,在地震作用下易发生液化致使坝体失稳溃坝,影响尾矿坝的使用安全。采用动三轴试验方法,以黑龙江省鸡西市石墨尾矿为对象,研究三种循环应力比(CSR)下细粒含量(F_(c))对石墨尾矿液化特性的影响规律;应用Ishibashi孔压模型对孔压增长过程进行模拟;同时研究固结比、围压以及饱和度对石墨尾矿液化特性的影响规律。研究结果表明,随细粒含量的增加,石墨尾矿的抵抗变形能力提高,孔压增长速率减慢,抗液化能力增强;随着CSR的增大,石墨尾矿的抵抗变形能力降低,孔压增长速率加快,抗液化能力减弱;Ishibashi孔压模型可以很好地模拟石墨尾矿液化过程中孔压的发展,对于不同细粒含量下的石墨尾矿非常适用。结果还表明,随着固结比及围压的增加,石墨尾矿的液化将逐渐被抑制,使其抗液化能力增强;随着饱和度的增加,可促进石墨尾矿的液化,使其抗液化能力减弱;CSR越小,各种因素对液化特性的影响效果越明显。研究结果可为石墨尾矿坝的液化研究提供科学合理的理论依据。

腐蚀环境下纳米SiO_(2)改良水泥土动弹性模量与阻尼比试验

近海地区工程建设项目大多受海水腐蚀和动荷载影响,为改善近海地区水泥土基础的力学性能,选取广州某沿海工程黏土制备纳米SiO_(2)改良水泥土试样,利用GDS真(动)三轴仪对改良水泥土进行循环加载试验,探究腐蚀状态下纳米SiO_(2)对水泥土力学性能的影响,分析不同腐蚀天数、不同海盐腐蚀浓度下改良水泥土的动弹性模量及阻尼特性。结果表明:纳米SiO_(2)改良水泥土动弹性模量随海盐腐蚀溶液浓度增大逐渐减小,其增长速率随海盐腐蚀时间增长逐渐减弱;与普通水泥土相比,在水泥土中掺入纳米SiO_(2)可明显增大水泥土动弹性模量,提高土体抗腐蚀能力;利用Konder模型得出水泥土动弹性模量倒数与动应变呈良好的线性关系,且纳米SiO_(2)改良水泥土最大动弹性模量E_(d0)相比于普通水泥土有明显提高;采用Darendeli模型对水泥土动弹性模进行分析,得到纳米SiO_(2)改良前后水泥土动模量比衰减模型,该模型能较好地描述海盐腐蚀环境下水泥土动弹性模量随动应变的变化规律;在海盐腐蚀时间相同的条件下,纳米SiO_(2)改良水泥土滞回圈面积S、阻尼比λ随海盐腐蚀溶液浓度增加不断增大,且均小于普通水泥土,水泥土经纳米SiO_(2)改良后,阻尼比λ的增长速率及增长量明显减小。在沿海腐蚀环境下,纳米SiO_(2)可有效提高水泥土力学性能,探究如何改良水泥土动力特性可为实际工程建设提供有效参考。

单双向循环荷载作用下砂砾料动模量和阻尼比试验研究

通过大型振动三轴试验,研究了单双向循环荷载作用下砂砾料动弹性模量和阻尼比的变化规律,分析围压和径向循环动应力对砂砾料动力参数的影响。研究结果表明:在双向振动三轴试验中,砂砾料的轴向动应变受径向动应力的影响较小,动应变主要与施加的轴向动应力大小有关;单双向振动下砂砾料的动弹性模量均随着动应变的增大而逐渐降低,双向振动时砂砾料动弹性模量随动应变的衰减速率基本不变,在相同动应变下双向振动的动模量均低于单向振动;砂砾料在双向振动时的阻尼比大于单向振动,双向振动时消耗的动应变能更大。通过对两种试验条件下的最大动弹性模量、动模量比进行分析,建立了表述单双向试验条件下最大动弹性模量的换算关系式和双向振动试验中动模量比和动应变的修正模型。

纳米硅溶胶改良辽宁台安砂土的抗液化性能研究

辽宁台安砂土属于易液化砂,提升其抗液化性能具有重要的工程意义。文章针对纳米硅溶胶(CS)对辽宁台安砂土抗液化性能的改良效果进行探究,通过不排水动三轴试验,对纯砂样和改良砂样的液化特性进行对比研究,分析CS浓度和固化时间两个参量对改良砂样动力特性的影响。研究结果表明:(1)CS能够显著提升台安砂土的抗液化性能,在动载作用下改良砂样均未发生液化破坏。(2)随CS浓度和固化时间的增加,试样动孔压u_(d)、动应变ε_(d)呈现先迅速下降后趋于平缓的发展规律;当CS浓度增至4%、固化时间达到3周后,试样抗液化性能的提升效果不再明显。(3)改良砂样的滞回曲线变得更加稳定。随CS浓度增加,阻尼先降低后趋于稳定,动弹性模量逐渐增大并趋于平缓,但伴随有一定的波动;随固化时间增大,阻尼呈减小趋势,动弹性模量呈增大趋势。研究成果可为辽宁台安地区砂土液化治理提供参考依据。

砂砾土振动体变评价方法与离心机模型试验验证

2008汶川地震出现了砂砾土大范围液化致灾现象,现场震害调查表明砂砾土场地存在砾石效应影响,现有砂土场地的震后沉降评价方法不适用于砂砾土场地。对此,在“张-社本”振动体变评价方法的基础上进一步发展了考虑砾石含量的砂砾土振动体变评价方法,然后开展动三轴试验确定评价方法中的相关参数,最后开展3组典型砾石含量的砂砾土地基离心机振动台模型试验对评价方法的可靠性进行验证。试验结果表明,砾石含量越高,振动引起的场地沉降变形越小;砂砾土振动体变评价方法可以较为准确地预测新近沉积砂砾土场地的震后沉降,但对存在地震历史影响的砂砾土场地,本文提出的评价方法较为保守,建议进一步发展考虑地震历史效应的砂砾土振动体变评价方法。