High-speed directly modulated distributed feedback laser based on detuned loading and photon-photon resonance effect

A monolithic integrated two-section distributed feedback(TS-DFB)semiconductor laser for high-speed direct modulation is proposed and analyzed theoretically.The grating structure of the TS-DFB laser is designed by the reconstructionequivalent-chirp(REC)technique,which can reduce the manufacturing cost and difficulty,and achieve high wavelength controlling accuracy.The detuned loading effect and the photon-photon resonance(PPR)effect are utilized to enhance the modulation bandwidth of the TS-DFB laser,exceeding 37 GHz,while that of the conventional one-section DFB laser is only 16 GHz.When the bit rate of the non-return-to-zero(NRZ)signal reaches 55 Gb/s,a clear eye diagram with large opening can still be obtained.These results show that the proposed method can enhance the modulation bandwidth of DFB laser significantly.

Beyond the 100 Gbaud directly modulated laser for short reach applications

It is very attractive to apply a directly modulated laser(DML)-based intensity-modulation and direct-detection(IM/DD)system in future data centers and 5G fronthaul networks due to the advantages of low cost,low system complexity,and high energy efficiency,which perfectly match the application scenarios of the data centers and 5G fronthaul networks,in which a large number of high-speed optical interconnections are needed.However,as the data traffic in the data centers and 5G fronthaul networks continues to grow exponentially,the future requirements for data rates beyond 100 Gbaud are challenging the existing DML-based IM/DD system,and the main bottleneck is the modulation bandwidth of the DML.In this paper,the data rate demands and technical standards of the data centers and 5G fronthaul networks are reviewed in detail.With the modulation bandwidth requirements,the technical routes and achievements of recent DMLs are reviewed and discussed.In this way,the prospects,challenges,and future development of DMLs in the applications of future data centers and 5G fronthaul networks are comprehensively explored.

35 km amplifier-less four-level pulse amplitude modulation signals enabled by a 23 GHz ultrabroadband directly modulated laser

The 4-level pulse amplitude modulation(PAM4)based on an 23 GHz ultrabroadband directly modulated laser(DML)was proposed.We have experimentally demonstrated that based on intensity modulation and direct detection(IMDD)56 Gbps per wavelength PAM4 signals transferred over 35 km standard single mode fiber(SSMF)without any optical amplification and we have achieved the bit error rate(BER)of the PAM4 transmission was under 2.9×10–4 by using feed forward equalization(FFE).

Shipborne aerosol IR decoy modulated by laser

Working principles, features, current situation and future development of the aerosol IR decoys are summarized in this paper, and a new type aerosol IR decoy——aerosol IR decoy modulated by laser is emphasized. The simulation results show that compared with the traditional IR decoys, the late-model aerosol IR decoy effectively enhances the capability of protecting targets and countermining IR guidance weapons. It is a new direction of aerosol IR decoys.

Widely Tunable Two-Section Directly Modulated DBR Lasers for TWDM-PON System

Wavelength tunable and directly modulated distributed Bragg reflector （DBR） lasers with butt-joint technology are designed, fabricated and characterized. The DBR laser consists of a gain section and a DBR section. To increase the electrical isolation between the gain section and the DBR section, parts of a p-doped material in the isolation region are etched off selectively. Over 2kΩ isolation resistance is realized ultimately without the need of ion implantation, which simplifies the fabrication process. The laser exhibits high speed modulation with a large tunable range. The 3dB direct modulation bandwidth of the device is over 8GHz in a 12nm tunable range. This widely tunable DBR laser with the simple structure is promising as a colorless light source for the next-generation time and wavelength division multiplexed passive optical network （TWDM-PON） systems.

Fabrication of 32 Gb/s Electroabsorption Modulated Distributed Feedback Lasers by Selective Area Growth Technology

A 32 Gb/s monolithically integrated electroabsorption modulated laser is fabricated by selective area growth technology. The threshold current of the device is below 13mA. The output power exceeds 10mW at 0V bias when the injection current of the distributed feedback laser is 100mA at 25℃. The side mode suppression ratio is over 50 dB. A 32Gb/s eye diagram is measured with a 3.SVpp nonreturn-to-zero pseudorandom modulation signal at -2.3 V bias. A clearly opening eyediagram with a dynamic extinction ratio of 8.01 dB is obtained.

Simulation of Intermediate State Absorption Enhancement in Rare-Earth Ions by Polarization Modulated Femtosecond Laser Field

We extend the third perturbation theory to study the polarization control behavior of the intermediate state absorption in Nd^（3＋）ions. The results show that coherent interference can occur between the single-photon and three-photon excitation pathways, and depends on the central frequency of the femtosecond laser field. Moreover,single-photon and three-photon absorptions have different polarization control efficiencies, and the relative weight of three-photon absorption in the whole excitation processes can increase with increasing the laser intensity.Therefore, the enhancement or suppression of the intermediate state absorption can be realized and manipulated by properly designing the intensity and central frequency of the polarization modulated femtosecond laser field.This research can not only enrich theoretical research methods for the up-conversion luminescence manipulation of rare-earth ions, but also can provide a clear physical picture for understanding and controlling multi-photon absorption in a multiple energy level system.

Optomagnonically tunable whispering gallery cavity laser wavelength conversion

We achieve laser wavelength conversion in an optomagnonical whispering gallery cavity by adjusting the strength of the applied static magnetic field. Numerical simulations are carried out on a yttrium iron garnet(YIG) sphere under different cavity quality factors or coupling strength. It is found that a high cavity quality factor will not always mean a high cavity excitation field for Gaussian lasers with finite linewidth. On state of the art, the high cavity quality factor will always mean the higher lightwave conversion rate. In addition, we also find that increasing the mode coupling strength is beneficial to the conversion of the laser. Our study provides new insights into generation of highly precise tunable coherent light.

NUMERICAL SIMULATION OF THE TEMPERATURE FIELD IN A SOLDER BALL UNDER PULSED LASER AND ITS EFFECT ON THE VIBRATION OF THE SOLDER

The research presented here is focused on the vibration condition of a small volume solder solder ball,which is placed on the surface of a soldering pad and is exerted a pulse modulated continuous wave laser heat source. Finite element method is applied to analyzed the temperature field in the solder ball, and experi- ment is conducted to test the vibration. the results show that,that, the temperature field flucturates with the same frequency as that of the laser pulse, which in turn causes a forced vibration of the same frequency in the liquid solder ball.

Ultrafast Modulation of the Molten Metal Surface Tension under Femtosecond Laser Irradiation

We predict ultrafast modulation of the pure molten metal surface stress fields under the irradiation of the single femtosecond laser pulse through the two-temperature model molecular-dynamics simulations. High-resolution and precision calculations are used to resolve the ultrafast laser-induced anisotropic relaxations of the pressure components on the time-scale comparable to the intrinsic liquid density relaxation time. The magnitudes of the dynamic surface tensions are found being modulated sharply within picoseconds after the irradiation, due to the development of the nanometer scale non-hydrostatic regime behind the exterior atomic layer of the liquid surfaces.The reported novel regulation mechanism of the liquid surface stress field and the dynamic surface tension hints at levitating the manipulation of liquid surfaces, such as ultrafast steering the surface directional transport and patterning.

Dynamic thermal modeling and parameter identification for a monolithic laser diode module

We improved the thermal equivalent-circuit model of the laser diode module（LDM） to evaluate its thermal dynamic properties and calculate the junction temperature of the laser diode with a high accuracy.The thermal parameters and the transient junction temperature of the LDM are modeled and obtained according to the temperature of the thermistor integrated in the module.Our improved thermal model is verified indirectly by monitoring the emission wavelength of the laser diode against gas absorption lines,and several thermal parameters are obtained with the temperature uncertainty of 0.01 K in the thermal dynamic process.

Spectroscopy system based on a single quantum cascade laser for simultaneous detection of CO and CO_2

A quantum cascade laser（QCL） based system for simultaneous detection of CO and CO_2 is developed.The QCL can scan over two neighboring CO（2055.40 cm^（-1）） and CO_2（2055.16 cm^（-1）） lines with a single current scan.The wavelength modulation spectroscopy（ f = 20 k Hz） is utilized to enhance the signal-to-noise ratio.A white cell with an effective optical path length of 74 m is used.The calibration of the sensor is performed and minimum detection limits of 1.3 ppb（1 × 10^（-9））for CO and 0.44 ppm（1 × 10^（-6）） for CO_2 are achieved.

High Coupling Efficiency of the Fiber-Coupled Module Based on Photonic-Band-Crystal Laser Diodes

The coupling efficiency of the beam combination and the fiber-coupled module is limited due to the large vertical divergent angle of conventional semiconductor laser diodes. We present a high coupling efficiency module using photonic-band-crystal （PBC） laser diodes with narrow vertical divergent angles. Three PBC single-emitter laser diodes are combined into a fiber with core diameter of 105μm and numerical aperture of 0.22. A high coupling efficiency of 94.4% is achieved and the brightness is calculated to be 1.T MW/（cm2.sr） with the injection current of 8A.

Directly modulated 25 Gbaud/s tunable in-series DFB laser array for WDM systems

In this Letter,we proposed and experimentally demonstrated a directly modulated tunable laser based on the multi-wavelength distributed feedback(DFB)laser array.The lasers are placed in series to avoid the usage of an optical combiner and additional power loss.A three-section design is utilized to reduce the interference from other lasers and improve the electro-optic response bandwidth.Besides,the reconstruction-equivalent-chirp technique is used to simplify the grating fabrication and precisely control the grating phase.We realized 12 channels with 100 GHz spacing with high side mode suppression ratios of above 50 dB.The output power of all the channels is above 14 mW.The 3 dB electro-optic bandwidth is above 20 GHz at a bias current of 100 mA for all four lasers.A 25 Gb/s data transmission over a standard single-mode fiber of up to 10 km is demonstrated for all 12 channels,and 50 Gb/s data per wavelength is obtained through the four-level pulse amplitude modulation.The proposed directly modulated tunable in-series DFB laser array shows the potential for a compact and low-cost light source for wavelength division multiplexing(WDM)systems,such as next-generation front-haul networks and passive optical networks.

Improved calibration method for displacement transformation coefficient in optical and visual measurements

Optical and visual measurement technology is used widely in fields that involve geometric measurements,and among such technology are laser and vision-based displacement measuring modules(LVDMMs).The displacement transformation coefficient(DTC)of an LVDMM changes with the coordinates in the camera image coordinate system during the displacement measuring process,and these changes affect the displacement measurement accuracy of LVDMMs in the full field of view(FFOV).To give LVDMMs higher accuracy in the FFOV and make them adaptable to widely varying measurement demands,a new calibration method is proposed to improve the displacement measurement accuracy of LVDMMs in the FFOV.First,an image coordinate system,a pixel measurement coordinate system,and a displacement measurement coordinate system are established on the laser receiving screen of the LVDMM.In addition,marker spots in the FFOV are selected,and the DTCs at the marker spots are obtained from calibration experiments.Also,a fitting method based on locally weighted scatterplot smoothing(LOWESS)is selected,and with this fitting method the distribution functions of the DTCs in the FFOV are obtained based on the DTCs at the marker spots.Finally,the calibrated distribution functions of the DTCs are applied to the LVDMM,and experiments conducted to verify the displacement measurement accuracies are reported.The results show that the FFOV measurement accuracies for horizontal and vertical displacements are better than±15μm and±19μm,respectively,and that for oblique displacement is better than±24μm.Compared with the traditional calibration method,the displacement measurement error in the FFOV is now 90%smaller.This research on an improved calibration method has certain significance for improving the measurement accuracy of LVDMMs in the FFOV,and it provides a new method and idea for other vision-based fields in which camera parameters must be calibrated.

112 Gbit/s transmitter optical subassembly based on hybrid integrated directly modulated lasers

Based on the hybrid integration technology, an ultra-compact and low cost transmitter optical subassembly module is proposed. Four directly modulated lasers are combined with a coarse wavelength division multiplexer operated at the O-band. The bandwidth for all channels is measured to be approximately 3 GHz. The 112 Gb∕s transmission is experimentally demonstrated for a 10 km standard single mode fiber（SSMF）, in which an optical isolator is used for avoiding the back-reflected and scattered light to improve the bit error rate（BER） performance. A low BER and clear eye opening are achieved for 10 km transmission.

Directly modulated active distributed reflector distributed feedback lasers over wide temperature range operation(-40 to 85℃)

We experimentally demonstrated that the distributed feedback(DFB) lasers with the active distributed reflector achieved a 25.8 Gb/s operation over a wide temperature range of -40 to 85℃. The DFB lasers can achieve additional feedback from an active distributed reflector with accurately controlled phase, and single-mode yields are not related to the position of cleave. The threshold currents of the fabricated laser are 6 mA and 20 mA at -40℃ and 85℃, respectively. The side mode suppression ratio of the fabricated laser is above 50 dB at all temperatures. Transmissions of 25.8 Gb/s after 10 km single-mode fibers with clear eye openings and less than 0.8 dB power penalty over a wide temperature range have been demonstrated as well.

Design of a single-mode directly modulated orbital angular momentum laser

We propose a design of single-mode orbital angular momentum(OAM) beam laser with high direct-modulation bandwidth. It is a microcylinder/microring cavity interacted with two types of second-order gratings: the complex top grating containing the real part and the imaginary part modulations and the side grating. The side grating etched on the periphery of the microcylinder/microring cavity can select a whispering gallery mode with a specific azimuthal mode number, while the complex top grating can scatter the lasing mode with travelling-wave pattern vertically. With the cooperation of the gratings, the laser works with a single mode and emits radially polarized OAM beams. With an asymmetrical pad metal on the top of the cavity, the OAM on-chip laser can firstly be directly modulated with electrical pumping. Due to the small active volume, the laser with low threshold current is predicted to have a high direct modulation bandwidth about 29 GHz with the bias current of ten times the threshold from the simulation. The semiconductor OAM laser can be rather easily realized at different wavelengths such as the O band, C band, and L band.

Modulated bandwidth enhancement in an amplified feedback laser

We report a direct, modulated bandwidth enhancement in a amplified feedback laser （AFL）, both experimen- tally and numerically. By means of fabricated devices, an enhanced -3 dB bandwidth of 27 GHz with an in-band flatness of ±3 dB is experimentally confirmed at 13℃. It is numerically confirmed that the modulated bandwidth of the AFL can be enhanced to two times its original bandwidth, with more controlled flexibility to realize a flat, small-signal response.

Potassium tantalate niobate crystals:Efficient quadratic electro-optic materials and their laser modulation technology

Electro-optic(EO)crystals are important material for all-solid-state laser technology,which can be used to fabricate various laser modulators,such as EO switches,laser deflectors,and optical waveguide.The improvements in new high-efficiency EO crystal materials have held great significance to the development of laser technology.Potassium tantalate niobate(KTN)is a popular multifunctional crystal because of its remarkable and excellent quadratic EO effect.KTN EO modulation technology offers numerous advantages,such as high efficiency,good stability,a quick response time,and inertia-free characteristics.In this paper,we summarize the research progress of KTN series crystals systemically,including the theoretical exploration on quadratic EO effect,solid-melt crystal growth technique,comprehensive physical characterization,new physical effect and mechanisms exploration,new EO devices development and design.The EO modulation technique based on the Kerr effect of KTN series crystal offers obvious advantages in reducing the drive voltage and device size,which could better meet the developmental needs of future lasers with a wide wavelength,miniaturization,and integration.This may provide theoretical guidance and an experimental basis for the design and development of new EO crystal devices and promote the development of laser technology.