Effect of pulsed laser process parameters on welding quality of automobile fuel injector

In this research, pulverization plate and base of a fuel injector in an automobile electronic-controlled engine was joined by pulsed laser welding. The different welding parameters were evaluated and effect of process parameters on joint characteristics was analyzed. The optimal process parameters were obtained as follows： welding current 120 A, welding speed 600 ram/rain, pulse duration 1.80 ms and pulse frequency 60 Hz. The microstructure of weld metal was investigated. Results show that the fusion zone is austenitic dendrite, the weld center is equiaxed grain, while the transition zone between fusion zone and weld center is mixed crystal with austenitic dendrite and equiaxed grain. The weld layered phenomenon was observed, and eddy caused by keyhole effect is the main reason for the formation of layered structure in molten pool.

Microstructure and mechanical properties of pulsed laser welded Al/steel dissimilar joint

Pulsed laser welding was used in joining pure aluminum to stainless steel in a lap joint configuration. It is found that the mechanical properties of the laser joints were closely correlated with the bead geometry, i.e., penetration depth. In order to study the correlation, two typical laser welds with different penetration depths were analyzed. In high penetration depth (354 μm) joint, Al-rich Fe?Al IMCs with microcracks were formed at the Al/fusion zone (FZ) interface. The joint strength was found to be (27.2±1.7) N/mm and three failure modes were observed near the Al/FZ interface. In low penetration depth (108 μm) joint, Fe-rich Fe?Al IMCs without any defect were formed at the Al/FZ interface. The joint strength was found to be (46.2±1.9) N/mm and one failure mode was observed across the FZ.

Geometrical, microstructural and mechanical characterization of pulse laser welded thin sheet 5052-H32 aluminium alloy for aerospace applications

Pulse laser welding of 0.6 mm-thick AA5052-H32 was performed to determine the optimum set of parameters including laser pulse current,pulse frequency and pulse duration that meets the AWS D17.1 specifications for aerospace industry.The microstructure and mechanical properties of the weldments were also investigated.Relationships between the parameters and weld bead geometry were found.High quality weld joints without solidification crack that met AWS D17.1 requirements were obtained at(I)high pulse energy(25 J)and high average peak power(4.2 kW)and(II)low pulse energy(17.6 J)and low average peak power(2.8 kW).The weld joint formed at lower heat energy input exhibited finer dendritic grain structure.Mg vapourisation and hard phase compound(Al0.5Fe3Si0.5)formation decreased in the weld joint formed at lower heat energy input.Consequently,the tensile strength of the weldment formed at lower heat energy input(168 MPa)is by a factor of 1.15 higher but showed^29%decrease in hardness(111 HV0.1)at the joint when being compared with the weldment formed at higher heat energy input.Appropriate parameters selection is critical to obtaining 0.6 mm-thick AA5052-H32 pulse laser weld joints that meet AWS D17.1 requirements for aircraft structures.

Microstructure,properties and first principles calculation of titanium alloy/steel by Nd: YAG laser self-fluxing welding

The experiment of Nd： YAG pulsed laser self-fluxing welding for 304 stainless steel/Ti6Al4V titanium alloy dissimilar metal was carried out. The microstructure properties of welded joint were analyzed by SEM, EDS and XRD. The equilibrium lattice constants, enthalpies of formation, cohesive energies, mechanical properties, Debye temperatures and valence electron structures of Ti-Fe intermetallic compounds （IMCs） were calculated by the first principle pseudopotential plane wave method based on density functional theory （DFT）. According to the thermodynamic data of Ti-Fe-Cr compounds, the Gibbs free energy per mole of compound at different temperatures was calculated and their thermal stability was compared. The results show that there are no macroscopic cracks in the welded joints, and the IMCs distributed evenly along the welding interface exhibits 3 distinct layers of microstructure with different colors. The welds interface generates IMCs of TiFe, TiFe 2 and a small amount of Ti 5Cr 7Fe 17 IMCs. Ti-Fe IMCs with high thermodynamic stability and easy alloying formation. The results of Gibbs free energies show that the sequence of precipitates in the interface is Ti 5Cr 7Fe 17 , TiFe 2 and TiFe in high temperature during the metallurgical reaction. The G/B values of Ti-Fe IMCs are greater than the critical value of 0.5, indicating that it is an intrinsic brittleness.

Improving pulsed laser weldability of duplex stainless steel to 5456 aluminum alloy via friction stir process reinforcing of aluminum by BNi-2 brazing alloy

Effects of laser pulse distance and reinforcing of 5456 aluminum alloy were investigated on laser weldability of Al alloy to duplex stainless steel (DSS) plates. The aluminum alloy plate was reinforced by nickel-base BNi-2 brazing powder via friction stir processing. The DSS plates were laser welded to the Al5456/BNi-2 composite and also to the Al5456 alloy plates. The welding zones were studied by scanning electron microscopy, X-ray diffractometry, micro-hardness and shear tests. The weld interface layer became thinner from 23 to 5 μm, as the laser pulse distance was increased from 0.2 to 0.5 mm. Reinforcing of the Al alloy modified the phases at interface layer from Al-Fe intermetallic compounds (IMCs) in the DSS/Al alloy weld, to Al-Ni-Fe IMCs in the DSS/Al composite one, since more nickel was injected in the weld pool by BNi-2 reinforcements. This led to a remarkable reduction in crack tendency of the welds and decreased the hardness of the interface layer from ~950 HV to ~600 HV. Shear strengths of the DSS/Al composite welds were significantly increased by ~150%, from 46 to 114 MPa, in comparison to the DSS/Al alloy ones.

Hot-cracking susceptibility and shear fracture behavior of dissimilar Ti6Al4V/AA6060 alloys in pulsed Nd:YAG laser welding

Laser welding of dissimilar titanium/aluminum alloys has been employed at an increasing rate,particularly in the aerospace industry,owing to its advantages in terms of current design flexibility and fuel/cost savings.The major problem with dissimilar Ti/Al welds arises from the difference in the thermal expansion and contraction of the two metals,which leads to hot-cracking susceptibility and the mitigation of the mechanical property after welding.In the present study,pulsed Nd:YAG laser welding of Ti6 Al4 V and AA6060 has been addressed.Hot-cracking susceptibility in the heat affected zone and the shear fracture behavior of the lap joints were investigated through microstructural characterization and mechanical tests.The results indicate that the hot cracking tendency can be reduced by increasing the pulse peak power(7.5–8.5 kW)and the laser point diameter(0.8–1.0 mm)with specific pulse duration and overlap.An alternative control strategy for less hot cracks in the Ti/Al lap joint can be to increase the weld width and decrease the cooling rate during solidification.The shear fracture of the Ti/Al lap joint is likely to occur along the lower side path of the weld interface with decreasing weld surface collapsed amount and increasing aluminum base metal melt depth.