The mechanical behavior of the test string in deep wells is generally relatively complex as a result of the high temperature and high pressure,severe dogleg and buckling effects,which in some circumstances can even le...The mechanical behavior of the test string in deep wells is generally relatively complex as a result of the high temperature and high pressure,severe dogleg and buckling effects,which in some circumstances can even lead to string failure.Traditional computational methods for the analysis of these behaviors are often inaccurate.For this reason,here a more accurate mechanical model of the test string is introduced by considering variables such as temperature,pressure,wellbore trajectory,and buckling,as well as combining them with the deformation and string constraint conditions brought in by changes in temperature and pressure during the tripping,setting,and test operations.The model is validated by applying it to a specific high-pressure gas well(located in Northeast Sichuan).展开更多
B4C, SiC and C, Cu functionally graded-materials (FGMs) have been developed by plasma spraying and hot pressing. Their high-heat flux properties have been investigated by high energy laser and electron beam for the si...B4C, SiC and C, Cu functionally graded-materials (FGMs) have been developed by plasma spraying and hot pressing. Their high-heat flux properties have been investigated by high energy laser and electron beam for the simulation of plasma disruption process of the future fusion reactors, And a study on eroded products of B4C/Cu FGM under transient thermal load of electron beam was performed. In the experiment, SEM and EDS analysis indicated that B4C and SiC were decomposed, carbon was preferentially evaporated under high thermal load, and a part of Si and Cu were melted, in addition, the splash of melted metal and the particle emission of brittle destruction were also found. Different erosive behaviors of carbon-based materials (CBMs) caused by laser and electron beam were also discussed.展开更多
High saturation magnetization and low coercivity are required for soft magnetic materials.This study investigated the Co_(47.5)Fe_(28.5)Ni_(19)Si_(3.3)Al_(1.7)high-entropy soft magnetic skeleton was prepared by select...High saturation magnetization and low coercivity are required for soft magnetic materials.This study investigated the Co_(47.5)Fe_(28.5)Ni_(19)Si_(3.3)Al_(1.7)high-entropy soft magnetic skeleton was prepared by selective laser melting.Then Al wpressure infiltrated into skeletons to obtain a dense composite material.The high-entropy composite materials possessed favorable compressive ductility and moderate soft magnetic properties.The high-entropy composite materials were obtained with Ms being 97.1 emu/g,79.8 emu/g,33 emu/g and possessing 19 Oe,15.8Oe and 17Oe of Hc,respectively.However,the magnetostriction coefficient remains low level,about 5ppm.These reported properties are attributed to the special structure of the material studied in present experiment.Nevertheless,a novel strategy of structural designing was proposed in this paper.展开更多
AIMTo utilize tissue micro measurement to study the effect of transient high intraocular pressure (IOP) induced by different durations of suction during laser in situ keratomileusis (LASIK) on rabbit retina thickness....AIMTo utilize tissue micro measurement to study the effect of transient high intraocular pressure (IOP) induced by different durations of suction during laser in situ keratomileusis (LASIK) on rabbit retina thickness.METHODSSixty healthy New Zealand white rabbits were randomly divided into a control group, and 3 negative-pressure suction groups (20s group, 45s group, and 3min group) and each group was comprised of 15 rabbits (30 eyes); the latter 3 groups were the transient high IOP models. The retinal tissue around the papilledema was separated. Hematoxylin and eosin (HE) staining was carried out to generate slices for light microscopy. The changes in the retina thickness values of each layer were measured for all animals in each group at different postoperative recovery periods and compared with the values recorded for the animals in the control group. The thickness of the retinal tissue showed a normal distribution. The ANOVA was performed by using SPSS13.0 statistic software.RESULTSIn the comparison between the 20s and 45s negative-pressure suction groups and the control group, no significant differences were observed, except at 14d. Significant difference was observed between the 3min negative-pressure suction group and the control group, and the retina thickness value of each layer reached a peak at 14d after repair.CONCLUSIONConventional negative suction during LASIK may not lead to significant changes in retinal tissue thickness; however, if the suction duration is increased to 3min, it will cause significant changes in retinal tissue thickness.展开更多
Although magnetotelluric sounding method applied to the land is advanced, there are many difficulties when it is applied to marine environment, one of which is how to lay magnetic field sensors down to the seafloor to...Although magnetotelluric sounding method applied to the land is advanced, there are many difficulties when it is applied to marine environment, one of which is how to lay magnetic field sensors down to the seafloor to complete measurements. To protect the magnetic field sensors from intense erosion and high pressure, suitable high-pressure sealed cabins must be designed to load them. For the consideration of magnetic measurement and marine operation, the sealed pressure cabin should be nonmagnetic and transportable. Among all optional materials, LC4 super.hard aluminum alloy has the highest performance of price/quality ratio to make the sealed pressure cabin. However, it does not mean that the high-pressure sealed cabin made using LC4 will be perfect in performance. In fact, because of its weak magnetism, the pressure cabin made using LC4 has distorting effect on frequency responses of the magnetic field sensors sealed in it. This distorting effect does not affect the use of the magnetic field sensor, but if we want to eliminate its effect, we should study it by experimental measurements. In our experiment tests, frequency sweep magnetic field as excitation signal was used, and then responses of the magnetic field sensor before and after being loaded into the high-pressure sealed cabin were measured. Finally, normalized abnormal curves for the frequency responses were obtained, through which we could show how the high-pressure sealed cabin produces effects on the responses of the magnetic field sensor. Experimental results suggest that the response distortion induced by the sealed pressure cabin appears on mid- and high-frequency areas. Using experimental results as standardization data, the frequency responses collected from seafloor magnetotelluric measurements can be corrected to restore real information about the seafloor field source.展开更多
A mathematical model was developed to describe moving laser welding by using the rotary Gauss body heat source model, and the effect of recoil pressure was taken into account. The formation of the long and narrow pool...A mathematical model was developed to describe moving laser welding by using the rotary Gauss body heat source model, and the effect of recoil pressure was taken into account. The formation of the long and narrow pool in high power fiber laser welding can be explained by the mathematical model (laser power: 10 kW, welding speed: 4 -20 m/min). Numerical simulation was conducted by PHOENICS software. The results show that at high welding velocity the plasma accelerated the velocity of liquid metal around the keyhole which is the main reason for the formation of the long and narrow molten pool in high power laser welding.展开更多
Usually the water head of the pumped storage hydro-plant is high, generally up to 400-500 m, therefore the rock mass under the high-pressure bifurcation pipe have to bear as high as millions Pascal water pressure, in ...Usually the water head of the pumped storage hydro-plant is high, generally up to 400-500 m, therefore the rock mass under the high-pressure bifurcation pipe have to bear as high as millions Pascal water pressure, in according with the requirements of high water head pumped storage hydro-plant should be 1.2 times of the water head special high-pressure packer permeability test compared with normal to test the permeability of rock and rock cleavage pressure value. The test results on the choice of design options often play a decisive role. Based on the engineering practice, the authors studied the drillhole high-pressure packer permeability test in the pumped storage hydro-plant's underground powerhouse, by the analysis of test results, this article offers a demonstration of the deformation of rock fracture witch under building in the condition of high-pressure water head, it provides a more detailed engineering geological background.展开更多
A theory for shifts of energy spectra due to electron-phonon interaction (EPI) has been developed. Both thetemperature-independent contributions and the temperature-dependent ones of acoustic branches and optical bran...A theory for shifts of energy spectra due to electron-phonon interaction (EPI) has been developed. Both thetemperature-independent contributions and the temperature-dependent ones of acoustic branches and optical brancheshave been derived. It is found that the temperature-independent contributions are very important, especially at lowtemperature. The total pressure-induced shift (PS) of a level (or spectral line or band) is the algebraic sum of its PSwithout EPI and its PS due to EPI. By means of both the theory for shifts of energy spectra due to EPI and the theoryfor PS of energy spectra, the total PS of R1 line of tunable laser crystal GSGG:Cr3+ at 70 K as well as the ones of itsR1 line, R2 line and U band at 300 K will be successfully calculated and explained in this series of papers.展开更多
Pentazolate compounds have attracted extensive attention as high energy density materials.The synthesis and recovery of pentazolate compounds is of great importance for their potential applications.Here,we report the ...Pentazolate compounds have attracted extensive attention as high energy density materials.The synthesis and recovery of pentazolate compounds is of great importance for their potential applications.Here,we report the synthesis of Pmn2_(1)-NaN_(5)and Pm-Na_(2)N_(5)through compressing and laser heating pure NaN_(3)at~60 GPa.Upon decompression,the pressureinduced structural transition from Pmn2_(1)-NaN_(5)into Cm-NaN_(5)is observed in the pressure range of 14-23 GPa for the first time.The cyclo-N_(5)^(-)can be traced down to 4.7 GPa at room temperature and recovered to ambient pressure under low temperature condition(up to 160 K).The Pm-Na_(2)N_(5)is suggested to decompose into the P4/mmm-NaN_(2)at 23 GPa,and be stable at ambient conditions.This work provides insight into the high-pressure behaviors of pentazolate compounds and an alternative way to stabilize energetic polynitrogen compounds.展开更多
By means of both a theory for pressure-induced shifts(PS) energy spectra and a theory for shifts of energy spectra due to electron-phonon interaction(EPIP.the pure electronic PS and the PS due to EPI of R1 line,R2 lin...By means of both a theory for pressure-induced shifts(PS) energy spectra and a theory for shifts of energy spectra due to electron-phonon interaction(EPIP.the pure electronic PS and the PS due to EPI of R1 line,R2 line,and U band of GSGG:Cr^3+ at 300 K have been calculated,respectively.The calcualted results are in good agreement with all the experimental data.Their physical origins have also been explained.It is found that the mixingdegree of t2^2(^3T1)e^4T2) and |t2^3 3E>base-wavefunctions in the wavefunctions of R1 level of GSGG:Cr^3+ at 300K is remarkable under normal pressure,and the mixing-degree rapidly decreases with increasing pressure.The change of the mixing-degree with pressure plays a key role not only for the pure electronic'PS of R1 line and R2 line but also the PS of R1 line and R2 line due to EPI.The pressure-dependent behaviors of the pure electronic 'PS of R1 line(or R2 line) and the PS of R1 line(or R2 line) due to EPI are quite different.It is the combined effect of them that gives rise to the total PS of R1 line(or R2 line).In the range of about 15 kar-45kbar,the mergence and /or order-reversal between t2^2(3T1)e^4T2 levels and t2^32T1 levels take place,which cause the fluctuation of the rate of PS for t2^2(3T1)e^4T2(or t2^32T1) with pressure,At 300K,both the temperature-dependent contribution to R1 line(Or R2 line or U band) from EPI and the temperature-independent one are important.展开更多
By means of both a theory for pressure-induced shifts (PS) of energy spectra and a theory for shifts ofenergy spectra due to electron-phonon interaction (EPI), the 'pure electronic' PS and the PS due to EPI of...By means of both a theory for pressure-induced shifts (PS) of energy spectra and a theory for shifts ofenergy spectra due to electron-phonon interaction (EPI), the 'pure electronic' PS and the PS due to EPI of R1 line ofGSGG:Cr3+ at 70 K have been calculated, respectively. Their physical origins have been revealed. It is found that theremarkable under the normal pressure, and the degree of the admixture rapidly decreases with increasing pressure. Thechange of the degree of the admixture with the pressure plays a key role for not only the pure electronic PS of R1 line butalso the PS ofR1 line due to EPL The detailed calculations and analyses show that the pressure-dependent behaviors ofthe pure electronic PS of R1 line and the PS of R1 line due to EPI are quite different. It is the combined effect of themthat gives rise to the total PS of R1 line, which has satisfactorily explained the experimental data (including a reversal ofPS of R1 line). In contributions to PS of R1 line due to EPI at 70 K, the temperature-independent contribution is muchlarger than the temperature-dependent contribution. The former results from the interaction between the zero-pointvibration of the lattice and localized electronic state.展开更多
目前,极紫外光被认为是制备特征尺寸小于7 nm芯片所必备的光源,激光轰击液态金属锡靶是其产生的主要方式之一.采用体积分数(volurne of fluid,VOF)方法建立了激光轰击金属锡液面产生溅射的模型,并对液料溅射和雾化的演化过程进行了数值...目前,极紫外光被认为是制备特征尺寸小于7 nm芯片所必备的光源,激光轰击液态金属锡靶是其产生的主要方式之一.采用体积分数(volurne of fluid,VOF)方法建立了激光轰击金属锡液面产生溅射的模型,并对液料溅射和雾化的演化过程进行了数值模拟,研究了冠状水花的产生机制以及雾化时的流场变化.在此基础上,进一步研究了金属液态锡在不同的能量、光斑直径和脉宽的激光轰击下溅射产生的冠的宽度和高度随时间演化情况.研究表明:在激光辐照产生的高压等离子体的高速冲击下,液膜经历快速运动、冠状射流和雾化3个阶段,液膜生长主要原因是惯性力作用;液膜上下两端存在较大的速度梯度是射流形状发生变化的主要原因;冠边缘处雾化现象的产生是由Rayleigh-Taylor和Plateau-Rayleigh不稳定性共同作用的结果.在激光轰击下,冠的高度和宽度随激光能量增加而增大,但随着时间推移,冠宽和冠高的增长速率逐渐减小;激光光斑和脉宽对冠宽及冠高的影响较为复杂,在前期影响较小,在后期冠宽及冠高随它们数值增加而减小.展开更多
文摘The mechanical behavior of the test string in deep wells is generally relatively complex as a result of the high temperature and high pressure,severe dogleg and buckling effects,which in some circumstances can even lead to string failure.Traditional computational methods for the analysis of these behaviors are often inaccurate.For this reason,here a more accurate mechanical model of the test string is introduced by considering variables such as temperature,pressure,wellbore trajectory,and buckling,as well as combining them with the deformation and string constraint conditions brought in by changes in temperature and pressure during the tripping,setting,and test operations.The model is validated by applying it to a specific high-pressure gas well(located in Northeast Sichuan).
文摘B4C, SiC and C, Cu functionally graded-materials (FGMs) have been developed by plasma spraying and hot pressing. Their high-heat flux properties have been investigated by high energy laser and electron beam for the simulation of plasma disruption process of the future fusion reactors, And a study on eroded products of B4C/Cu FGM under transient thermal load of electron beam was performed. In the experiment, SEM and EDS analysis indicated that B4C and SiC were decomposed, carbon was preferentially evaporated under high thermal load, and a part of Si and Cu were melted, in addition, the splash of melted metal and the particle emission of brittle destruction were also found. Different erosive behaviors of carbon-based materials (CBMs) caused by laser and electron beam were also discussed.
基金National Natural Science Foundation of China(NSFC,Granted Nos.51671020)Guangdong Basic and Applied Basic Research Foundation(No.2019B1515120020)Creative Research Groups of China(No.51921001).
文摘High saturation magnetization and low coercivity are required for soft magnetic materials.This study investigated the Co_(47.5)Fe_(28.5)Ni_(19)Si_(3.3)Al_(1.7)high-entropy soft magnetic skeleton was prepared by selective laser melting.Then Al wpressure infiltrated into skeletons to obtain a dense composite material.The high-entropy composite materials possessed favorable compressive ductility and moderate soft magnetic properties.The high-entropy composite materials were obtained with Ms being 97.1 emu/g,79.8 emu/g,33 emu/g and possessing 19 Oe,15.8Oe and 17Oe of Hc,respectively.However,the magnetostriction coefficient remains low level,about 5ppm.These reported properties are attributed to the special structure of the material studied in present experiment.Nevertheless,a novel strategy of structural designing was proposed in this paper.
文摘AIMTo utilize tissue micro measurement to study the effect of transient high intraocular pressure (IOP) induced by different durations of suction during laser in situ keratomileusis (LASIK) on rabbit retina thickness.METHODSSixty healthy New Zealand white rabbits were randomly divided into a control group, and 3 negative-pressure suction groups (20s group, 45s group, and 3min group) and each group was comprised of 15 rabbits (30 eyes); the latter 3 groups were the transient high IOP models. The retinal tissue around the papilledema was separated. Hematoxylin and eosin (HE) staining was carried out to generate slices for light microscopy. The changes in the retina thickness values of each layer were measured for all animals in each group at different postoperative recovery periods and compared with the values recorded for the animals in the control group. The thickness of the retinal tissue showed a normal distribution. The ANOVA was performed by using SPSS13.0 statistic software.RESULTSIn the comparison between the 20s and 45s negative-pressure suction groups and the control group, no significant differences were observed, except at 14d. Significant difference was observed between the 3min negative-pressure suction group and the control group, and the retina thickness value of each layer reached a peak at 14d after repair.CONCLUSIONConventional negative suction during LASIK may not lead to significant changes in retinal tissue thickness; however, if the suction duration is increased to 3min, it will cause significant changes in retinal tissue thickness.
基金This paper is supported by the National "863" Program in the Tenth Five-Year-Plan (No. 2002AA615020)Eleventh Five-Year-Plan (No. 2006AA09A201)the Focused Subject Program of Beijing (No. XK104910598).
文摘Although magnetotelluric sounding method applied to the land is advanced, there are many difficulties when it is applied to marine environment, one of which is how to lay magnetic field sensors down to the seafloor to complete measurements. To protect the magnetic field sensors from intense erosion and high pressure, suitable high-pressure sealed cabins must be designed to load them. For the consideration of magnetic measurement and marine operation, the sealed pressure cabin should be nonmagnetic and transportable. Among all optional materials, LC4 super.hard aluminum alloy has the highest performance of price/quality ratio to make the sealed pressure cabin. However, it does not mean that the high-pressure sealed cabin made using LC4 will be perfect in performance. In fact, because of its weak magnetism, the pressure cabin made using LC4 has distorting effect on frequency responses of the magnetic field sensors sealed in it. This distorting effect does not affect the use of the magnetic field sensor, but if we want to eliminate its effect, we should study it by experimental measurements. In our experiment tests, frequency sweep magnetic field as excitation signal was used, and then responses of the magnetic field sensor before and after being loaded into the high-pressure sealed cabin were measured. Finally, normalized abnormal curves for the frequency responses were obtained, through which we could show how the high-pressure sealed cabin produces effects on the responses of the magnetic field sensor. Experimental results suggest that the response distortion induced by the sealed pressure cabin appears on mid- and high-frequency areas. Using experimental results as standardization data, the frequency responses collected from seafloor magnetotelluric measurements can be corrected to restore real information about the seafloor field source.
文摘A mathematical model was developed to describe moving laser welding by using the rotary Gauss body heat source model, and the effect of recoil pressure was taken into account. The formation of the long and narrow pool in high power fiber laser welding can be explained by the mathematical model (laser power: 10 kW, welding speed: 4 -20 m/min). Numerical simulation was conducted by PHOENICS software. The results show that at high welding velocity the plasma accelerated the velocity of liquid metal around the keyhole which is the main reason for the formation of the long and narrow molten pool in high power laser welding.
文摘Usually the water head of the pumped storage hydro-plant is high, generally up to 400-500 m, therefore the rock mass under the high-pressure bifurcation pipe have to bear as high as millions Pascal water pressure, in according with the requirements of high water head pumped storage hydro-plant should be 1.2 times of the water head special high-pressure packer permeability test compared with normal to test the permeability of rock and rock cleavage pressure value. The test results on the choice of design options often play a decisive role. Based on the engineering practice, the authors studied the drillhole high-pressure packer permeability test in the pumped storage hydro-plant's underground powerhouse, by the analysis of test results, this article offers a demonstration of the deformation of rock fracture witch under building in the condition of high-pressure water head, it provides a more detailed engineering geological background.
文摘A theory for shifts of energy spectra due to electron-phonon interaction (EPI) has been developed. Both thetemperature-independent contributions and the temperature-dependent ones of acoustic branches and optical brancheshave been derived. It is found that the temperature-independent contributions are very important, especially at lowtemperature. The total pressure-induced shift (PS) of a level (or spectral line or band) is the algebraic sum of its PSwithout EPI and its PS due to EPI. By means of both the theory for shifts of energy spectra due to EPI and the theoryfor PS of energy spectra, the total PS of R1 line of tunable laser crystal GSGG:Cr3+ at 70 K as well as the ones of itsR1 line, R2 line and U band at 300 K will be successfully calculated and explained in this series of papers.
基金Project supported by the National Key R&D Program of China(Grant No.2018YFA0305900)the National Nat-ural Science Foundation of China(Grant Nos.12174143,11634004,11847094,and 11804384)JLU Science and Technology Innovative Research Team(Grant No.2017TD-01)。
文摘Pentazolate compounds have attracted extensive attention as high energy density materials.The synthesis and recovery of pentazolate compounds is of great importance for their potential applications.Here,we report the synthesis of Pmn2_(1)-NaN_(5)and Pm-Na_(2)N_(5)through compressing and laser heating pure NaN_(3)at~60 GPa.Upon decompression,the pressureinduced structural transition from Pmn2_(1)-NaN_(5)into Cm-NaN_(5)is observed in the pressure range of 14-23 GPa for the first time.The cyclo-N_(5)^(-)can be traced down to 4.7 GPa at room temperature and recovered to ambient pressure under low temperature condition(up to 160 K).The Pm-Na_(2)N_(5)is suggested to decompose into the P4/mmm-NaN_(2)at 23 GPa,and be stable at ambient conditions.This work provides insight into the high-pressure behaviors of pentazolate compounds and an alternative way to stabilize energetic polynitrogen compounds.
文摘By means of both a theory for pressure-induced shifts(PS) energy spectra and a theory for shifts of energy spectra due to electron-phonon interaction(EPIP.the pure electronic PS and the PS due to EPI of R1 line,R2 line,and U band of GSGG:Cr^3+ at 300 K have been calculated,respectively.The calcualted results are in good agreement with all the experimental data.Their physical origins have also been explained.It is found that the mixingdegree of t2^2(^3T1)e^4T2) and |t2^3 3E>base-wavefunctions in the wavefunctions of R1 level of GSGG:Cr^3+ at 300K is remarkable under normal pressure,and the mixing-degree rapidly decreases with increasing pressure.The change of the mixing-degree with pressure plays a key role not only for the pure electronic'PS of R1 line and R2 line but also the PS of R1 line and R2 line due to EPI.The pressure-dependent behaviors of the pure electronic 'PS of R1 line(or R2 line) and the PS of R1 line(or R2 line) due to EPI are quite different.It is the combined effect of them that gives rise to the total PS of R1 line(or R2 line).In the range of about 15 kar-45kbar,the mergence and /or order-reversal between t2^2(3T1)e^4T2 levels and t2^32T1 levels take place,which cause the fluctuation of the rate of PS for t2^2(3T1)e^4T2(or t2^32T1) with pressure,At 300K,both the temperature-dependent contribution to R1 line(Or R2 line or U band) from EPI and the temperature-independent one are important.
文摘By means of both a theory for pressure-induced shifts (PS) of energy spectra and a theory for shifts ofenergy spectra due to electron-phonon interaction (EPI), the 'pure electronic' PS and the PS due to EPI of R1 line ofGSGG:Cr3+ at 70 K have been calculated, respectively. Their physical origins have been revealed. It is found that theremarkable under the normal pressure, and the degree of the admixture rapidly decreases with increasing pressure. Thechange of the degree of the admixture with the pressure plays a key role for not only the pure electronic PS of R1 line butalso the PS ofR1 line due to EPL The detailed calculations and analyses show that the pressure-dependent behaviors ofthe pure electronic PS of R1 line and the PS of R1 line due to EPI are quite different. It is the combined effect of themthat gives rise to the total PS of R1 line, which has satisfactorily explained the experimental data (including a reversal ofPS of R1 line). In contributions to PS of R1 line due to EPI at 70 K, the temperature-independent contribution is muchlarger than the temperature-dependent contribution. The former results from the interaction between the zero-pointvibration of the lattice and localized electronic state.
文摘目前,极紫外光被认为是制备特征尺寸小于7 nm芯片所必备的光源,激光轰击液态金属锡靶是其产生的主要方式之一.采用体积分数(volurne of fluid,VOF)方法建立了激光轰击金属锡液面产生溅射的模型,并对液料溅射和雾化的演化过程进行了数值模拟,研究了冠状水花的产生机制以及雾化时的流场变化.在此基础上,进一步研究了金属液态锡在不同的能量、光斑直径和脉宽的激光轰击下溅射产生的冠的宽度和高度随时间演化情况.研究表明:在激光辐照产生的高压等离子体的高速冲击下,液膜经历快速运动、冠状射流和雾化3个阶段,液膜生长主要原因是惯性力作用;液膜上下两端存在较大的速度梯度是射流形状发生变化的主要原因;冠边缘处雾化现象的产生是由Rayleigh-Taylor和Plateau-Rayleigh不稳定性共同作用的结果.在激光轰击下,冠的高度和宽度随激光能量增加而增大,但随着时间推移,冠宽和冠高的增长速率逐渐减小;激光光斑和脉宽对冠宽及冠高的影响较为复杂,在前期影响较小,在后期冠宽及冠高随它们数值增加而减小.