Research on a deconvolution algorithm for laser-induced fluorescence diagnosis based on the maximum entropy principle

Laser-induced fluorescence(LIF)spectroscopy is employed for plasma diagnosis,necessitating the utilization of deconvolution algorithms to isolate the Doppler effect from the raw spectral signal.However,direct deconvolution becomes invalid in the presence of noise as it leads to infinite amplification of high-frequency noise components.To address this issue,we propose a deconvolution algorithm based on the maximum entropy principle.We validate the effectiveness of the proposed algorithm by utilizing simulated LIF spectra at various noise levels(signal-to-noise ratio,SNR=20–80 d B)and measured LIF spectra with Xe as the working fluid.In the typical measured spectrum(SNR=26.23 d B)experiment,compared with the Gaussian filter and the Richardson–Lucy(R-L)algorithm,the proposed algorithm demonstrates an increase in SNR of 1.39 d B and 4.66 d B,respectively,along with a reduction in the root-meansquare error(RMSE)of 35%and 64%,respectively.Additionally,there is a decrease in the spectral angle(SA)of 0.05 and 0.11,respectively.In the high-quality spectrum(SNR=43.96 d B)experiment,the results show that the running time of the proposed algorithm is reduced by about98%compared with the R-L iterative algorithm.Moreover,the maximum entropy algorithm avoids parameter optimization settings and is more suitable for automatic implementation.In conclusion,the proposed algorithm can accurately resolve Doppler spectrum details while effectively suppressing noise,thus highlighting its advantage in LIF spectral deconvolution applications.

The comparison of manganese spectral lines for self-absorption reduction in LIBS using laser-induced fluorescence

The detection of manganese(Mn)in steel by laser-induced breakdown spectroscopy(LIBS)provides essential information for steelmaking.However,self-absorption greatly disrupts the LIBS spectral lines of Mn with high content.In this study,to minimize self-absorption for Mn spectral lines in LIBS,laser-induced fluorescence(LIF)was applied.Compared with conventional LIBS,the self-absorption factors(α)of Mn I 403.08,403.31,and 403.45 nm lines were reduced by 90%,88%,and 88%,respectively;the root mean square errors of crossvalidation were decreased by 88%,85%,and 87%,respectively;the average relative errors were reduced by 93%,90%,and 91%,respectively;and average relative standard deviations were decreased by 29%,32%,and 33%,respectively.The LIBS-LIF was shown to successfully minimize the self-absorption effect and spectral intensity fluctuation and improve detection accuracy.

Laser-induced Fluorescence Spectroscopy of NiS： Identification of a Low-lying Electronic State

Laser-induced fluorescence excitation spectra of jet-cooled NiS molecules were recorded in the energy range of 12200-13550 cm^-1. Four vibronic bands with rotational structure have been observed and assigned to the [12.4]^3∑-0-X^3∑0 transition progression. The relevant rotational constants, significant isotopic shifts, and （equilibrium） molecular parameters have been determined. In addition, the lifetimes of the observed bands have also been measured.

B-X and C-X Band Systems of CuCl Revisited： Laser-induced Fluorescence Study in 465-490 nm

We have reinvestigated the B-X and C-X band systems of CuCl by recording the laser- induced fluorescence excitation spectra in 20400-21800 cm^-1. The rotational analyses in Hund＇s case （a） revealed unambiguously a singlet-to-singlet transition nature. The radiative lifetimes were measured to be 4.670 and 4.667 μs, respectively, which are much longer than that expected for a pure singlet of CuCl. This implies that the fluorescence mechanism in the B or C band systems lies in the mixing of the singlets （^1II and ^1E^＋） and triplets （^3II0,1,2） and that the two excited states observed in our experiment might be the singlets that have been strongly ＂contaminated＂ by their triplet neighbors.

Laser-induced Fluorescence and Dispersed Fluorescence Spectroscopy of NiB： Identification of a New 2П State in 19000-22100 cm^-1

The laser-induced fluorescence excitation spectra of jet-cooled NiB radicals have been recorded in the energy range of 19000-22100 cm-1. Eleven bands have been assigned to the [20.77]2П-X2∑＋ transition system for the first time. The dispersed fluorescence spectra related to most of these bands have been investigated. Vibrationally excited levels of the ground electronic state, with v＂ up to 6, have been observed. In addition, the lifetimes for almost all the observed bands have also been measured.

Laser-induced Fluorescence Spectrum of CoS Between 15200 and 19000 cm^-1

Laser-induced fluorescence excitation spectra of jet-cooled CoS molecules have been recorded in the energy range of 15200-19000 cm^-1. Five transition progressions have been reported for the first time, the assignments of these progressions have been derived from a rotational analysis of vibronic bands and they are determined to be [15.58]^4△7/2-X^4△7/2, [16.02]^4△7/2- X^4△7/2, [16.50]^4△7/2-X^4△T/2, [17.80]^4II5/2-X^4△7/2, and [18.00]^4△7/2-X^4△7/2 transitions. In addition, under the supersonic jet condition the fluorescent lifetimes of these vibronic states were measured by exponentially fitting the fluorescence decay. Based on the observed spectra and the measured lifetimes of the vibronic states, the newly identified electronic states are discussed.

Quantitative measurements of one-dimensional OH absolute concentration profiles in a methane/air flat flame by bi-directional laser-induced fluorescence

The one-dimensional （1D） spatial distributions of OH absolute concentration in methane/air laminar premixed flat flame under different equivalence ratios at atmospheric pressure are investigated by using bi-directional laser-induced flu- orescence （LIF） detection scheme combined with the direct absorption spectroscopy. The effective peak absorption cross section and the average temperature at a height of 2 mm above the burner are obtained by exciting absorption on the Q1（8） rotational line in the A2∑＋ （Dt = 0） ←- X2∏ （v = 0） at 309.240 nm. The measured values are 1.86×10-15 cm2 and 1719 K, respectively. Spatial filtering and frequency filtering methods of reducing noise are used to deal with the experi- mental data, and the smoothing effects are also compared using the two methods. The spatial distribution regularities of OH concentration are obtained with the equivalence ratios ranging from 0.8 to 1.3. The spatial resolution of the measured result is 84μm. Finally, a comparison is made between the experimental result of this paper and other relevant study results.

Quantitative measurement of hydroxyl radical(OH) concentration in premixed flat flame by combining laser-induced fluorescence and direct absorption spectroscopy

An accurate and reasonable technique combining direct absorption spectroscopy and laser-induced fluorescence（LIF）methods is developed to quantitatively measure the concentrations of hydroxyl in CH;/air flat laminar flame. In our approach, particular attention is paid to the linear laser-induced fluorescence and absorption processes, and experimental details as well. Through measuring the temperature, LIF signal distribution and integrated absorption, spatially absolute OH concentrations profiles are successfully resolved. These experimental results are then compared with the numerical simulation. It is proved that the good quality of the results implies that this method is suitable for calibrating the OH-PLIF measurement in a practical combustor.

Semi-analytical Monte Carlo simulation of laser-induced fluorescence propagation in an optically participating spray

A semi-analytical Monte Carlo (SMC) simulation was developed to simulate the propagation of laser-induced fluo- rescence (LIF) in an optically participating spray, which simultaneously exhibits spectrally dependent emission, anisotropic scattering, absorption, and re-emission. The SMC simulation is described and then applied to an experimental configuration of a cloud of polydisperse droplets composed of water and sulforhodamine B dye. In the SMC simulation, the collected LIF flux on the remote receptor element is calculated as the global contribution from the emissive source, single, twice, … and nth collision events in any sequence. The effects on the fluorescence photons propagation of spray parameters like the dye concentration, droplets concentration, and droplets size are examined. Three spectral bands representing different optical properties are chosen to analyze the interference of absorption, scattering and re-emission on the detected LIF flux. The obtained spectral LIF flux distribution on the receptor demonstrates a “red shift” phenomenon.

Numerical analysis of quantitative measurement of hydroxyl radical concentration using laser-induced fluorescence in flame

The aim of the present work is to quantitatively measure the hydroxyl radical concentration by using LIF（laserinduced fluorescence） in flame.The detailed physical models of spectral absorption lineshape broadening,collisional transition and quenching at elevated pressure are built.The fine energy level structure of the OH molecule is illustrated to understand the process with laser-induced fluorescence emission and others in the case without radiation,which include collisional quenching,rotational energy transfer（RET）,and vibrational energy transfer（VET）.Based on these,some numerical results are achieved by simulations in order to evaluate the fluorescence yield at elevated pressure.These results are useful for understanding the real physical processes in OH-LIF technique and finding a way to calibrate the signal for quantitative measurement of OH concentration in a practical combustor.

Absorption,quenching,and enhancement by tracer in acetone/toluene laser-induced fluorescence

To measure the equivalent ratio distribution of the two-stage lean premixed(DLP)flame,we propose using acetone/toluene planar laser-induced fluorescence(PLIF)technology to simultaneously measure the concentrations of the two components.Appropriate excitation laser wavelength and filters are used to assess the influence of acetone and toluene on each other’s fluorescence signal at room temperature.Experimental results show that acetone has a strong absorption effect on toluene’s fluorescence signal,the effective absorption cross-section is 5.77×10-20 cm-2.Acetone has an obvious quenching effect on the toluene fluorescence signal,and the Stern–Volmer coefficient is 0.50 kPa-1.The collisions between the molecules of toluene and acetone will lead to the enhancement of the fluorescence signal of acetone,and the enhancement coefficient is exponential with the acetone’s concentration.The quantitative relationship between the fluorescence intensity and the concentrations of the two tracers is obtained by establishing the photophysical model of toluene and acetone’s fluorescence signals.

The investigation of OH radicals produced in a DC glow discharge by laser-induced fluorescence spectrometry

In this paper the OH radicals produced by a needle-plate negative DC discharge in water vapor,N_(2)+H_(2)O mixture gas and He+H_(2)O mixture gas are investigated by a laser-induced fluorescence(LIF)system.With a ballast resistor in the circuit,the discharge current is limited and the discharges remain in glow.The OH rotation temperature is obtained from fluorescence rotational branch fitting,and is about 350 K in pure water vapor.The effects of the discharge current and gas pressure on the production and quenching processes of OH radicals are investigated.The results show that in water vapor and He+H_(2)O mixture gas the fluorescence intensity of OH stays nearly constant with increasing discharge current,and in N_(2)+H_(2)O mixture gas the fluorescence intensity of OH increases with increasing discharge current.In water vapor and N_(2)+H_(2)O mixture gas the fluorescence intensity of OH decreases with increasing gas pressure in the studied pressure range,and in He+H_(2)O mixture gas the fluorescence intensity of OH shows a maximum value within the studied gas pressure range.The physicochemical reactions between electrons,radicals,ground and metastable molecules are discussed.The results in this work contribute to the optimization of plasma reactivity and the establishment of a molecule reaction dynamics model.

Simultaneous laser-induced fluorescence and contactless-conductivity detection for microfluidic chip

A combined detection system involving simultaneous LIF and contacfless-conductometric measurements at the same place of the microfluidic chip was described. The LIF measurement was designed according to the confocal principle and a moveable contactless-conduetivity detector was used in C^4D. Both measurements were mutually independent and advantageous in analyses of mixtures. Various experimental parameters affecting the response were examined and optimized. The performances were demonstrated by simultaneous detection of Rhodamine B. And the results showed that the combined detection system could be used sensitively and reliably.

Absolute density measurement of nitrogen dioxide with cavity-enhanced laser-induced fluorescence

The absolute number density of nitrogen dioxide（NO2） seeded in argon is measured with cavity-enhanced laserinduced fluorescence（CELIF） through using a pulsed laser beam for the first time. The cavity ring down（CRD） signal is acquired simultaneously and used for normalizing the LIF signal and determining the relationship between the measured CELIF signal and the NO2 number density. The minimum detectable NO2 density down to（3.6±0.1）10^8 cm^-3 is measured in 60 s of acquisition time by the CELIF method. The minimum absorption coefficient is measured to be（2.0±0.1）10^-9 cm^-1, corresponding to a noise equivalent absorption sensitivity of（2.2±0.1）10^9 cm.^-1Hz^-1/2. The experimental system demonstrated here can be further improved in its sensitivity and used for environmental monitoring of outdoor NO2 pollution.

Automatic separation system for marine meiobenthos based on laser-induced fluorescence technology

An automatic system for marine meiobenthos separation was developed by using laser-induced fluorescence tech- nology. Rose Bengal was used as organism dye and the spectrums of Rose Bengal were measured. Laser-induced fluorescence system was established to detect marine meiobenthos in sediments. Data obtained from experiments were analyzed by using a mathematical model. The results showed that laser-induced fluorescence technology worked well in the system. The system could select the meiobenthos efficiently and precisely.

Production of Polyclonal Antibody of Morphine and Determination of Morphine in Urine by Capillary Electrophoresis Immunoassay with Laser-induced Fluorescence Detection

N-Conjugated antigen was synthesized and polyclonal antibody with high specificity was obtained from immunizing animals. With this polyclonal antibody, a rapid and efficient CEIA-LIF method was developed to determine the free morphine in urine of abusers. The detection limit was calculated to be 40 ng/mL. Simulated urine samples were analyzed with good recoveries, which showed the feasibility of its application in specific morphine determination in urine of morphine abusers.

Laser-induced Fluorescence Spectroscopy of CoS： Identification of a New Excited State Arising from the Ground State

Laser-induced fluorescence excitation spectra and dispersed fluorescence spectra of cobalt sulfide （COS） have been recorded in the energy range of 22400-24400 cm-1 （corresponding to 446-409 nm）. A new electronic transition progression with six vibronic bands, stemming from the X4AT/2 state of CoS, was identified and assigned to be [24.0014AT/2-X4A7/2. The new observed 4A state most probably originates from the core[10a2][47r3][lla2][153][57r3] electronic configuration. Strong perturbations are found to extensively exist in the transition bands of this new state. The rotational constants and lifetimes of these bands have been determined.

Determination of Amino Acids in an Individual Erythrocyteby Capillary Electrophoresis with Intracellular FITC-derivatization and Laser-induced Fluorescence Detection

A novel approach for analysis of amino acids in individual erythrocytes was established. In this method, the derivatization reagent was introduced into the living cells by electroporation. After derivatization, the amino acids in a single cell were determined by capillary electrophoresis with laser-induced fluorescence detection.

Effects of temperature and pressure on OH laser-induced fluorescence exciting A-X (1,0) transition at high pressures

The effects of temperature and pressure on laser-induced fluorescence(LIF)of OH are numerically studied under the excitation of A-X(1,0)transition at high pressures.A detailed theoretical analysis is carried out to reveal the physical processes of LIF.It is shown that high pressure LIF measurements get greatly complicated by the variations of pressure-and temperature-dependent parameters,such as Boltzmann fraction,absorption lineshape broadening,central-frequency shifting,and collisional quenching.Operations at high pressures require a careful choice of an excitation line,and the Q1(8)line in the A-X(1,0)band of OH is selected due to its minimum temperature dependence through the calculation of Boltzmann fraction.The absorption spectra of OH become much broader as pressure increases,leading to a smaller overlap integral and thus smaller excitation efficiency.The central-frequency shifting cannot be omitted at high pressures,and should be taken into account when setting the excitation frequency.The fluorescence yield is estimated based on the LASKIN calculation.Finally,OH-LIF measurements were conducted on flat stoichiometric CH4/air flames at high pressures.And both the numerical and experimental results illustrate that the pressure dependence of fluorescence yield is dominated,and the fluorescence yield is approximately inversely proportional to pressure.These results illustrate the physical processes of OH-LIF and provide useful guidelines for high-pressure application of OH-LIF.

The far-field plasma characterization in a 600W Hall thruster plume by laser-induced fluorescence

Non-intrusive characterization of the singly ionized xenon velocity in Hall thruster plume using laser induced fluorescence(LIF)is critical for constructing a complete picture of plume plasma,deeply understanding the ion dynamics in the plume,and providing validation data for numerical simulation.This work presents LIF measurements of singly ionized xenon axial velocity on a grid ranging from 100 to 300 mm in axial direction and from 0 to 50 mm in radial direction for a600 W Hall thruster operating at the nominal condition of discharge voltage 300 V and discharge current 2 A,the influence of discharge voltage is investigated as well.The ion velocity distribution function(IVDF)results in the far-field plume demonstrate a profile of bimodal IVDFs,especially prominent at radial distances greater than channel inner radius of 22 mm at axial position of 100 mm,which is quite different from that of the near-field plume where bimodal IVDFs occur in the central core region for the same power Hall thruster when compared to previous LIF measurements of BHT-600 by Hargus(2010 J.Propulsion Power 26135).Beyond 100 mm,only single-peak IVDFs are measured.The two-dimensional ion velocity vector field indicates the bimodal axial IVDF is merely a geometry effect for the annular discharge channel in the far-field plume.Results about the IVDF,the most probable velocity and the accelerating potential profile along the centerline all indicate that ions are still accelerating at axial distances greater than 100 mm,and the maximum most probable velocity measured at300 mm downstream of the exit plane is about 19 km s-1.In addition,the most probable velocity of ions along radial direction changes a little except the lower velocity ion populations in the bimodal IVDF cases.The ion temperature at axial distances of 10 and 300 mm oscillates along the radial direction,while the ion temperature first increases,and then decreases for the 200 mm case.Finally,the axial position for the ion peak axial velocity on the thruster centerline is shifted upstream for higher discharge voltages,and the velocity curve is becoming steeper with the discharge voltage before reaching the maximum.This observation can be used as a criterion to optimize the thruster performance.