Dimethyl acridine-based self-assembled monolayer as a hole transport layer for highly efficient inverted perovskite solar cells

Self-assembled monolayers(SAMs)have recently emerged as excellent hole transport materials in inverted perovskite solar cells(PSCs)owing to their ability to minimize parasitic absorption,regulate energy level alignment,and passivate perovskite defects.Herein,we design and synthesize a novel dimethyl acridinebased SAM,[2-(9,10-dihydro-9,9-dimethylacridine-10-yl)ethyl]phosphonic acid(2PADmA),and employ it as a hole-transporting layer in inverted PSCs.Experimental results show that the 2PADmA SAM can modulate perovskite crystallization,facilitate carrier transport,passivate perovskite defects,and reduce nonradiative recombination.Consequently,the 2PADmA-based device achieves an enhanced power conversion efficiency(PCE)of 24.01%and an improved fill factor(FF)of 83.92%compared to the commonly reported[2-(9H-carbazol-9-yl)ethyl]phosphonic acid(2PACz)-based control device with a PCE of 22.32%and FF of 78.42%,while both devices exhibit comparable open-circuit voltage and short-circuit current density.In addition,2PADmA-based devices exhibit outstanding dark storage and thermal stabilities,retaining approximately~98%and 87%of their initial PCEs after 1080 h of dark storage and 400 h of heating at 85°C,respectively,both considerably superior to the control device.

In-situ investigation of atmospheric corrosion behavior of bronze under thin electrolyte layers using electrochemical technique

The atmospheric corrosion behavior of bronze under thin electrolyte layer （TEL） with different thicknesses was monitored using cathodic polarization curves, open circuit potential （OCP） and electrochemical impedance spectroscopy （EIS）. Cathodic polarization result indicates that the cathodic limiting current density increases with decreasing the TEL thickness. EIS result shows that the corrosion rate increases with decreasing the TEL thickness at the initial stage because the corrosion is dominated by the cathodic process, whereas after long immersion time, the corrosion degree with the TEL thickness is in the sequence of 150 μm 〉 310 μm〉 10μm ≈ bulk solution 〉 57 μm. The measurements of OCP and EIS present in-situ electrochemical corrosion information and their results are in good agreement with that of physical characterizations.

Tribological behaviors of Fe-Al-Cr-Nb alloyed layer deposited on 45 steel via double glow plasma surface metallurgy technique

Double glow plasma surface metallurgy technique was used to fabricate a Fe?Al?Cr?Nb alloyed layer onto the surface of the 45 steel. The microstructures and composition of th?eA Fl?eCr?Nb alloyed layer were analyzed by scanning electronic microscopy, X-ray diffraction and energy dispersive spectroscopy. The results indicate thatthe 20 μm alloyed layer is homogeneous and compact. The alloyed elements exhibit a gradient distribution along the cross section. Microhardness and nanoindentation tests imply that the surface hardness of the alloyed layer reaches HV 580, which is almost 2.8 times that of the substrate. Compared with the substrate, the alloyed layer has a much smaller displacement and a larger elastic modulus. According to the friction and wear tests at room temperature, the? FeAl?Cr?Nb alloyed layer has lower friction coefficient and less wear mass, implying that the Fe?Al?Cr?Nb alloyed layer can effectively improve the surface hardness and wear resistance of the substrate.

Layer by Layer Self-assembly Fiber-based Flexible Electrochemical Transistor

Poly(3,4-ethylenedioxyethiophene)-polystyrene sulfonic acid(PEDOT:PSS)/polyallyl dimethyl ammonium chloride modified reduced graphene oxide(PDDA-rGO)was layer by layer self-assembled on the cotton fiber.The surface morphology and electric property was investigated.The results confirmed the dense membrane of PEDOT:PSS and the lamellar structure of PDDA-rGO on the fibers.It has excellent electrical conductivity and mechanical properties.The fiber based electrochemical transistor(FECTs)prepared by the composite conductive fiber has a maximum output current of 8.7 mA,a transconductance peak of 10 mS,an on time of 1.37 s,an off time of 1.6 s and excellent switching stability.Most importantly,the devices by layer by layer self-assembly technology opens a path for the true integration of organic electronics with traditional textile technologies and materials,laying the foundation for their later widespread application.

A Laboratory Modeling of the Velocity Field in the Convective Boundary Layer with the Particle Image Velocimetry Technique

Based on the research of the convective boundary layer (CBL) temperature field in a convective tank, this paper studies the characteristics of the CBL velocity field in the convective tank. Aluminium powder (400 orders) is used as a tracer particle in the application of the particle image velocimetry (PIV) technique. The experiment demonstrates: the velocity distribution in the mixed layer clearly possesses the characteristics of CBL thermals; the velocity distribution in the top zone of the mixed layer shows entrainment layer characteristics; the vertical distribution of turbulent characteristic variables is reasonable, which is similar to field observations and other tank results; the error analysis demonstrates the validity of aluminium powder, which implies the reliability of the results.

Numerical simulation of protection range in exploiting the upper protective layer with a bow pseudo-incline technique

The developing processes of stress and deformation fields of a protected layer after mining an upper-protective layer with a bow pseudo-incline technique were simulated to locate the protection region. The pressure relief of the protected layer was analyzed after mining the upper-protective layer. The pressure relief angle along the strike and incline were located according to the roles of protection of the deformation and stress pressure-relief of the protective layer after mining. This results show that the upper-protective layer with the bow pseudo-incline technique have an upper and downside pressure relief angle of 85 and 68 degrees respectively; the distribution of strike pressure relief angles along the pseudo-incline working face is uneven and their values range from 38.3 to 51 degrees. The pressure relief angle of the inclined middle location was the largest. The distribution of the protection region of the upper-protective layer with the bow pseudo-incline teelmique located by practical tests and numerical simulation is essentially consistent, compared with the results obtained by these methods.

Uniform stable conformal convolutional perfectly matched layer for enlarged cell technique conformal finite-difference time-domain method

Based on conformal construction of physical model in a three-dimensional Cartesian grid,an integral-based conformal convolutional perfectly matched layer（CPML） is given for solving the truncation problem of the open port when the enlarged cell technique conformal finite-difference time-domain（ECT-CFDTD） method is used to simulate the wave propagation inside a perfect electric conductor（PEC） waveguide.The algorithm has the same numerical stability as the ECT-CFDTD method.For the long-time propagation problems of an evanescent wave in a waveguide,several numerical simulations are performed to analyze the reflection error by sweeping the constitutive parameters of the integral-based conformal CPML.Our numerical results show that the integral-based conformal CPML can be used to efficiently truncate the open port of the waveguide.

Bacteria Adherence Properties of Nitrided Layer on Ti6Al4V by the Plasma Nitriding Technique

The nitrided layer on Ti6A14V substrate was prepared by the plasma nitriding technique. The sample was characterized by X-ray diffraction （XRD）, glow discharge optical emission spectroscopy （GDOES）, X-ray photoelectron spectroscopy （XPS）, and rough-meter. X- ray diffraction analysis reveals that TiN, Ti2N and Ti phase exist in the nitrided layer subsurface. GDOES analysis shows the thickness of the nitrided layer is about 3 ~tm. XPS analysis shows that there is higher N, lower A1 and lower V in the nitrided layer surface than in the Ti6A14V surface. Rough-meter analysis results show the roughness of the nitrided layer is greater than that of Ti6A14V alloy base. The bacteria adherence property of the nitrided layer on Ti6A14V substrate on the Streptococcus mutans was investigated and compared with that of Ti6A14V alloy by fluorescence microscope. It shows that the nitrided layer inhibits the bacteria adherence.

Asexual Propagation of Sheanut Tree (<i>Vitellaria paradoxa</i>C.F. Gaertn.) Using a Container Layering Technique

In spite of the economic potential of the sheanut tree (Vitellaria paradoxa), its domestication still has not been achieved due to the long juvenile period of seed propagated plants and the absence of a reliable vegetative propagation method. Three experiments were conducted by using a modified container layering technique to investigate the effects of season (rainy and dry season), light treatments (etiolation and natural light) and indole 3-butyric acid (IBA) on root formation in juvenile and mature sheanut trees. The effect of light treatments on the internal conditions such as level of sugars (soluble, insoluble and total sugars) and total free phenols in layered sheanut shoots was also considered. Rooting was generally lower in the mature trees (27.9%) compared to that in juvenile 4 year-old plants (40.9%). Etiolation increased the levels of total sugars and phenols in shoots of 4-year-old plants and mature fruit bearing trees, but this increase did not significantly enhance rooting in both the juvenile and mature sheanut trees. The container layering technique holds promise as a method for the asexual propagation of sheanut planting material. Roots formed using this method looked healthy and were vertically orientated giving layered shoots a better chance at survival.

One-half layer pancreaticojejunostomy with the rear wall of the pancreas reinforced:A valuable anastomosis technique

BACKGROUND Postoperative pancreatic fistula(POPF)is one of the most common and serious complications after pancreaticoduodenectomy(PD).To effectively reduce the incidence of POPF,we designed a new type of pancreaticojejunostomy(PJ),which was termed one-half layer PJ with the rear wall of the pancreas reinforced.AIM To explore the clinical application value of this new technique.METHODS We compared 62 patients who had undergone PD by either the traditional ductto-mucosa anastomoses or the new one-half layer PJ with the rear wall of the pancreas reinforced method at our hospital from May 2015 to September 2019.All 62 patients were operated by the same surgeon experienced in both procedures.We retrospectively analyzed patient characteristics,perioperative outcomes,and surgical results.RESULTS There was no significant difference between the two groups in basic information except the postoperative hospital stays,14.7±5.4 d in the traditional duct-tomucosa anastomoses group and 12.0±4.2 d in the one-half layer PJ group(P=0.042).In terms of postoperative complications,the one-half layer PJ group had a lower rate of POPF than the traditional group.The overall number of cases with POPF was 8(24.2%)in the traditional group and 2(6.9%)in the one-half layer group(P=0.017).Additionally,the rate of grades B and C POPF was lower in the one-half layer group(3.4%)compared with that(12.1%)in the traditional group(P=0.010).One patient died due to hemorrhage caused by severe pancreatic fistula in the traditional group.CONCLUSION One-half layer PJ with the rear wall of the pancreas reinforced is a safe and feasible procedure that can successfully reduce the rate of POPF.It may be a promising technique for PJ after PD.

Unsteady Boundary Layer Flow and Heat Transfer Due to a Stretching Sheet by Quasilinearization Technique

In this paper, the problem of unsteady laminar boundary-layer flow and heat transfer of a viscous income-pressible fluid over stretching sheet is studied numerically. The unsteadiness in the flow and temperature is caused by the time-dependent stretching velocity and surface temperature. A similarity transformation is used to reduce the governing boundary-layer equations to couple higher order non-linear ordinary differential equations. These equations are numerically solved using quasi-linearization technique. The effect of the governing parameters unsteadiness parameter and Prandtl number on velocity and temperature profile is discussed. Besides the numerical results for the local skin friction coefficient and local Nusselt number are presented. The computed results are compared with previously reported work.

Corrosion Inhibition from Thiol Self-assembly Layer: A High Pressure Perspective

Taking dodecanethiol as the representative, we investigated the corrosion inhibition performance of SAL in seawater under pressures from 0.1 to 9 MPa. By using scanning Kelvin probe, the dodecanethiol SAL is confirmed to build on Cu surface, and the modification of SAL has positively shifted the surface potential to realize the inertness. Electrochemical techniques, such as electrochemical impedance spectroscopy and potentiodynamic polarization were used to reveal the corrosion behavior of Cu modified by SAL under the different pressure, i e, 0.1, 3, 6, and 9 MPa. It is indicated that the longer modification time affords better corrosion resistance to Cu. Higher static pressure is easier to deteriorate the corrosion inhibition capability due to the penetration effect. A plausible mechanism is proposed to illustrate the degradation process of SAL in the high pressure seawater environment.

Biomimetic“Nacre-like”Films Prepared via Layer-by-Layer Self-assembly of Mica,Polyvinyl Alcohol and Polymethyl Methacrylate

A film with“brick-and-mortar”structure was prepared by layer-by-layer(LBL)technique using polyvinyl alcohol(PVA)and polymethyl methacrylate(PMMA)as the flexible material or“mortar”and mica as the rigid material or“brick”.The film deposited on a glass slide after self-assembly cycles had a thickness of 3μm thick and an uneven,wavy surface.The film exhibits enhanced mechanical properties,i e,the hardness and indentation modulus values could reach 6.14 and 68.41 GPa,respectively.The hardness and elastic toughness were found to be depended on three factors,i e,the ratio of PVA to mica,the number of self-assembly cycles,and the pretreatment method of the mica suspension.The self-assembly process was driven by formation of the hydrogen bonds between the silanol groups of mica and the hydroxyl groups of PVA and carbonyl groups of PMMA.

基于layer-by-layer技术构建胆碱检测生物传感器酶电极的研究

基于层层累积自组装法将PDDA高分子材料和胆碱氧化酶逐层固定在高分子聚合膜PVS／PDDA修饰的电极表面，制备了电流型胆碱检测生物传感器。利用石英晶体微天平（QCM）分别分析了PDDA和胆碱氧化酶的固定过程，结果表明酶的固定量可以得到有效控制。探讨了自组装膜层数、pH值、温度对传感器电流响应的影响。制备的生物传感器在胆碱浓度为5×10^-7～1×10^-4mol／L的范围内对胆碱有良好的线性响应，响应时间为10s，检出限为5×10^-7mol／L。传感器的稳定性好，30天时的响应值仍保持90％。

Microstructure of Ni /WC Surface Composite Layer on Gray Iron Substrate

The surface infiltrated composite （Ni/WC） layers on gray iron substrate were fabricated through a vacuum infiltration casting technique （VICT） using Ni-based composite powder with different WC particles content as raw materials.The microstructures of surface infiltrated composite layer,the interface structures between surface composite layer and the substrate,the changes of macro-hardness with the increasing of WC content and the micro-hardness distribution are investigated.The infiltrated composite layer includes a surface composite layer and a transition layer,and the thickness of the transition layer decreases with the increasing content of WC.The thickness of transition layer with 20%WC content in the surface infiltrated composite layer was 170 μm which was the thickest for all transition layers with different WC content.The surface composite layer was mainly composed of WC,W2C,FeB and NiB,along with Ni-Cr-Fe,Ni （Cr） solid solution,Ni （Si） solid solution and Ni （Fe） solid solution.The transition layer was composed of Ni （Cr） solid solution,Ni （Fe） solid solution,Ni （Si） solid solution,Fe （Ni） solid solution and eutectic.The surface macro-hardness and micro-hardness of the infiltrated layer had been evaluated.The macro-hardness of the surface composite layer decreases with the WC content increasing,and the average macro-hardness is HRC60.The distribution of micro-hardness presents gradient change.The average micro-hardness of the infiltrated layer is about HV1000.

ALGEBRAIC TURBUL ENCE MODEL WITH MEM ORY FOR COMPUTATION OF 3-D TURBULENT BOUNDARY LAYERS WITH VALIDATION

Additional equations were found based on experiments for an algebraic turbulence model to improve the prediction of the behavior of three dimensional turbulent boundary layers by taking account of the effects of pressure gradient and the historical variation of eddy viscosity, so the model is with memory. Numerical calculation by solving boundary layer equations was carried out for the five pressure driven three dimensional turbulent boundary layers developed on flat plates, swept wing, and prolate spheroid in symmetrical plane. Comparing the computational results with the experimental data, it is obvious that the prediction will be more accurate if the proposed closure equations are used, especially for the turbulent shear stresses.

Few‐layer carbon nitride photocatalysts for solar fuels and chemicals:Current status and prospects

Converting sunlight directly to fuels and chemicals is a great latent capacity for storing renewable energy.Due to the advantages of large surface area,short diffusion paths for electrons,and more exposed active sites,few‐layer carbon nitride(FLCN)materials present great potential for production of solar fuels and chemicals and set off a new wave of research in the last few years.Herein,the recent progress in synthesis and regulation of FLCN‐based photocatalysts,and their applications in the conversion of sunlight into fuels and chemicals,is summarized.More importantly,the regulation strategies from chemical modification to microstructure control toward the production of solar fuels and chemicals has been deeply analyzed,aiming to inspire critical thinking about the effective approaches for photocatalyst modification rather than developing new materials.At the end,the key scientific challenges and some future trend of FLCN‐based materials as advanced photocatalysts are also discussed.

Anti-Corrosion and Reconstruction of Surface Crystal Plane for Zn Anodes by an Advanced Metal Passivation Technique

For the aqueous Zn-ion battery,dendrite formation,corrosion,and interfacial parasitic reactions are major issues,which greatly inhibits their practical application.How to develop a method of Zn construction or treatment to solve these issues for Zn anodes are still great challenges.Herein,a simple and cheap metal passivation technique is proposed for Zn anodes from a corrosion science perspective.Similar to the metal anticorrosion engineering,the formed interfacial protective layer in a chemical way can sufficiently solve the corrosion issues.Furthermore,the proposed passivity approach can reconstruct Zn surface-preferred crystal planes,exposing more(002)planes and improving surface hydrophilicity,which inhibits the formation of Zn dendrites and hydrogen evolution effectively.As expected,the passivated Zn achieves outstanding cycling life(1914 h)with low voltage polarization(<40 mV).Even at 6 mA cm^(−2) and 3 mA h cm^(−2),it can achieve stable Zn deposition over 460 h.The treated Zn anode coupled with MnO_(2) cathode shows prominently reinforced full batteries service life,making it a potential Zn anode candidate for excellent performance aqueous Zn-ion batteries.The proposed passivation approach provides a guideline for other metal electrodes preparation in various batteries and establishes the connections between corrosion science and batteries.

Similarity solutions to a laminar boundary layer problem in power law fluids

A suitable similarity transformation is introduced to reduce the laminarboundary layer equations of power law fluids to a class of singular nonlinear two-point boundaryvalue problems. The kin friction and shear stress distributions for boundary layer flow over amoving flat plate are investigated by utilizing the shooting technique. Results indicate that foreach fixed value of the power law exponent n or the velocity ratio parameter xi, the skin frictionand shear stress decrease with the increasing of n or xi respectively.

Thermal diffusivity of light-emitting diode packaging material determined by photoacoustic piezoelectric technique

Thermal property is one of the most important properties of light-emitting diode （LED）. Thermal property of LED packaging material determines the heat dissipations of the phosphor and the chip surface, accordingly having an influence on the light-emitting efficiency and the life-span of the device. In this paper, photoacoustic piezoelectric （PAPE） technique has been employed to investigate the thermal properties of polyvinyl alcohol （]？VA） and silicon dioxide, which are the new and the traditional packaging materials in white LED, respectively. Firstly, the theory of PAPE technique has been developed for two-layer model in order to investigate soft materials; secondly, the experimental system has been set up and adjusted by measuring the reference sample; thirdly, the thermal diffusivities of PVA and silicon dioxide are measured and analysed. The experimental results show that PVA has a higher thermal diffusivity than silicon dioxide and is a better packaging material in the sense of thermal diffusivity for white LED.