Synthesis and characterization of colored layered double hydroxides for thermal stabilizer

Colored layered double hydroxides （LDHs） can be synthesized by introducing colored cations such as Fe^3＋ and Cr^3 ＋, which call be used as thermal stabilizers for polyvinyl chloride （PVC）. The yellowish Mg/Fe and bluish Mg/Cr LDHs are prepared by the co-precipitation method. The results show that the MgsCr_ CO3 and Mg3Fe_ CO3 colored layered double hydroxides can stabilize PVC for more than 30 min under the thermal aging temperature of 180 ℃. The preparation can use cheap Mg（OH） 2 instead of MgCl2, which produces a much smaller amount of the by-product NH4Cl. It is known that NH4Cl is a cheap fertilizer that is difficult to sell; therefore, the preparation is much greener and more economic than the one using magnesium salt.

Flexible white top-emitting organic light-emitting diode with a MoO_x roughness improvement layer

In this paper, an MoOx film is deposited on a polyethylene terephthalate （PET） substrate as a buffer layer to improve the surface roughness of the flexible PET substrate. With an optimized MoOx thickness of 100 nm, the surface roughness of the PET substrate can be reduced to a very small value of 0.273 nm （much less than 0.585 nm of the pure PET）. Flexible white top-emitting organic light-emitting diodes （TEOLEDs） with red and blue dual phosphorescent emitting layers are constructed based on a low-reflectivity Sm/Ag semi-transparent cathode. The flexible white emission exhibits the best luminance and current injection characteristics with the 100-nm-thick MoOx buffer layer and this result indicates that a smooth substrate is beneficial to the enhancement of device electrical and electroluminescence performances. However, the white TEOLED with a 50-nm-thick MoOx buffer layer exhibits a maximum current efficiency of 4.64 cd/A and a power efficiency of 1.9 lm/W, slightly higher than those with a 100-nm MoOx buffer layer, which is mainly due to an obvious intensity enhancement but limited current increases in 50-nm MoOx-based white TEOLED. The change amplitudes of the Commission International de l’Eclairage （CIE） chromaticity coordinates are less than （0.016, 0.005） for all devices in a wide luminance range over 100 cd/m2, indicating an excellent color stability in our white flexible TEOLEDs. Additionally, the flexible white TEOLED with an MoOx buffer layer shows excellent flexibility to withstand more than 500 bending times under a curvature radius of approximately 9 mm. Research demonstrates that it is mainly attributed to the high surface energy of the MoOx buffer layer, which is conducible to the improvement of the surface adhesion to the PET substrate and the Ag anode.

Energy distribution in white organic light-emitting diodes with three primary color emitting layers

Two types of organic light-emitting diodes with structures of ITO/N,N'-bis(1-naphthyl)-N,N'-diphenyl,1,1'-biphenyl-4,4'-diamine (NPB)/tris(8-hydroquinolinato)aluminum(Alq 3)/2,9-dimethyl-4,7-diphenyl-l,10-phenanthroline(BCP)/Alq 3:4-dicyanomethylene-2-(tert-butyl)-6-methyl-4H-pyran(DCJTB)/Alq 3 /Al and ITO/NPB/BCP/Alq 3 /Alq 3:DCJTB/Alq 3 /Al were studied.NPB was chosen as a hole-transporting/blue-emitting layer.Alq 3 adjacent to BCP acted as a green emitting layer while that adjacent to the Al cathode acted as an electron-transporting layer.Alq 3 doped with 2 wt.% DCJTB was used as a red emitting layer.The operating principles of the devices were explained by the mechanism of F rster energy transfer and the hole and exciton blocking effect of BCP.It was found that the spectral characteristics of the devices strongly depended on the relative location between the green emitting Alq 3 layer and the BCP layer,as well as their thickness.Pure white emission with the CIE coordinates of (0.33,0.33) was achieved by mixing the three primary colors in the device with the structure of ITO/NPB(30 nm)/BCP(6 nm)/Alq 3 (30 nm)/Alq 3:DCJTB(30 nm)/Alq 3 (30 nm)/Al.The BCP layer played an important role in distributing the exciton energy among the three emitting layers to achieve a balanced white light.The white emission of this device was largely insensitive to the driving voltage (15-27 V) with the insertion of the green emitting Alq 3 layer.

White phosphorescent organic light-emitting diodes using double emissive layer with three dopants for color stability

We fabricate white phosphorescent organic light-emitting diodes （PHOLEDs） with three dopants and double emissive layer （EML） to achieve color stability. The white PHOLEDs use FIrpic dopant for blue EML （B- EML）, and Ir（ppy）3：Ir（piq）3 dopants for green：red EML （GR-EML） with N,N＇-dicarbazolyl-3, 5-benzene （mCP） as host material. Thicknesses of B-EML and GR-EML are adjusted to form a narrow recombination zone at two EML＇s interface and charge trapping happens in EML according to wide highest occupied molecular orbital and/or lowest unoccupied molecular orbital energy band gap of mCP and smaller energy band gap of dopants. The total thickness of both EMLs is fixed at 30 nm in the device structure of ITO （150 nm）/MoO3 （2 nm）/N,N＇-diphenyl-N,N＇-bis（1-naphthyl-phenyl）-（1,1″-biphenyl）-4, 4＇-diamine （70 nm）/ meP：Firpic-8.0% （12 nm）/mCP：Ir（ppy）3-3.0%：Ir（piq）3-1.5% （18 nm）/2″,2＇,2＂＇-（1,3,5-benzinetriyl）-tris（1- phenyl-l-H-benzimidazole） （30 nm）/8-hydroxyquinolinolato-lithium （2 nm）/A1 （120 nm）. White PHOLED shows 18.25 cd/A of luminous efficiency and white color coordinates of （0.358 and 0.378） at 5000 cd/m2 and color stability with slight CIExy change of （0.028 and 0.002） as increasing luminance from 1000 to 5000 cd/m^2.

Diffusion curves with diffusion coefficients

Diffusion curves can be used to generate vector graphics images with smooth variation by solving Poisson equations. However, using the classical diffusion curve model, it is difficult to ensure that the generated diffusion image satisfies desired constraints. In this paper, we develop a model for producing a diffusion image by solving a diffusion equation with diffusion coefficients, in which color layers and coefficient layers are introduced to facilitate the generation of the diffusion image. Doing so allows us to impose various constraints on the diffusion image, such as diffusion strength, diffusion direction,diffusion points, etc., in a unified computational framework. Various examples are presented in this paper to illustrate the capabilities of our model.