Cross Layered MAC Design for RF Energy Harvesting Sensor Network

The main research objective in wireless sensor networks (WSN) domain is to develop algorithms and protocols to ensure minimal energy consumption with maximum network lifetime. In this paper, we propose a novel design for energy harvesting sensor node and cross-layered MAC protocol using three adjacent layers (Physical, MAC and Network) to economize energy for WSN. The basic idea behind our protocol is to re-energize the neighboring nodes using the radio frequency (RF) energy transmitted by the active nodes. This can be achieved by designing new energy harvesting sensor node and redesigning the MAC protocol. The results show that the proposed cross layer CL_EHSN improves the life time of the WSN by 40%.

Passive shock wave/boundary layer control of wing at transonic speeds

At supercritical conditions a porous strip （or slot strip） placed beneath a shock wave can reduce the drag by a weaker lambda shock system, and increase the buffet boundary, even may increase the lift. Passive shock wave/boundary layer control （PSBC） for drag reduction was conducted by SC（2）-0714 supercritical wing, with emphases on parameter of porous/slot and bump, such as porous distribution, hole diameter, cavity depth, porous direction and so on. A sequential quadratic programming （SQP） optimization method coupled with ad]oint method was adopted to achieve the optimized shape and position of the bumps. Computational fluid dynamics （CFD）, force test and oil test with half model all indicate that PSBC with porous, slot and bump generally reduce the drag by weaker lambda shock at supercritical conditions. According to wind tunnel test results for angle of attack of 2° at Mach number M = 0.8, the porous configuration with 6.21% porosity results in a drag reduction of 0.0002 and lift-drag ratio increase of 0.2, the small bump configuration results in a drag reduction of 0.0007 and lift-drag ratio increase of 0.3. Bump normally reduce drag at design point with shock wave position being accurately computed. If bump diverges from the position of shock wave, drag will not be easily reduced.

Proposal for a cross layer scheme for real-time wireless video

This paper focuses on the design of the cross layer between the video application layer and the MIMO physical layer. MIMO physical layer research has promised an enormous increase in the capacity of wireless communication systems. Also MIMO wireless systems operate under fading conditions where the channel faces arbitrary fluctuations. Since the wireless channel changes over each coherence period, the capacity of the wireless channel, given the power constraints, changes. Hence to make efficient use of the available capacity one needs to adapt the video bit rate. However it is impossible to adapt at the application layer as changing the parameters of the video takes more time than the coherence period of the channel. In this paper we address this problem through a novel solution and also investigate its performance through a simulation study.

Energy Efficient and QoS Aware Framework for Video Transmission over Wireless Sensor Networks

Wireless Multimedia Sensor Networks (WMSNs), is a network of sensors, which are limited in terms of memory, computing, bandwidth, and battery lifetime. Multimedia transmission over WSN requires certain QoS guarantees such as huge amount of bandwidth, strict delay and lower loss ratio that makes transmitting multimedia is a complicated task. However, adopting cross-layer approach in WMSNs improves quality of service of WSN under different environmental conditions. In this work, an energy efficient and QoS aware framework for transmitting multimedia content over WSN (EQWSN) is presented, where packet, queue and path scheduling were introduced. It adapts the application layer parameter of video encoder to current wireless channel state, and drops less important packets in case of network congestion according to packet type. Finally, the path scheduling differentiates packets types/priority and route them through different paths with different QoS considering network lifetime. Simulation results show that the new scheme EQWSN transmits video quality with QoS guarantees in addition to prolonging network lifetime.

Symmetrical periods used as matching layers in multilayer thin film design

Properties of symmetrical layers as matching layers in multilayer thin film design were analyzed. A calculation method was presented to derive parameters of desired equivalent refractive index. A harmonic beam splitter was designed and fabricated to test this matching method. OCIS codes： 230.1360, 220.0220, 310.6860.

Optimal Scheduling Method in MIMO WLAN with Distributed Coordination Function

This paper addresses the optimal number of simultaneous data transmissions that maximize the system throughput in an MIMO WLAN. To facilitate simultaneous packet transmissions, both transceivers have to exchange preambles to calculate the channel state information. This exchange is combined with the RTS （request to send）/CTS （clear to send） handshake which is used to contend for the channel in WLANs. This study presents an expression for the optimal number of simultaneous data transmissions under the distributed coordinate function mechanism derived using the Markov chain model, as well as an analytical formula for the optimal system throughput given the length of the contention window and the number of nodes in the network. The analytical results show that the system throughput cannot be enhanced by simply increasing the numoer of simultaneous data transmissions.