Investigations have been made on the effects of temperature and fine disperse phase of disordered γ on strain hardening rate of Ni3Al based alloy. The result is found that there exists a peak temperature for the stra...Investigations have been made on the effects of temperature and fine disperse phase of disordered γ on strain hardening rate of Ni3Al based alloy. The result is found that there exists a peak temperature for the strain hardening rate of Ni3Al based alloy below the peak temperature of its yield strength. Analysis shows that the appearance of the peak temperature of strain hardening rate is caused by both the decreasing of the movability of <101> superdislocations on {111}slip plane and the increasing of the dynamic recovery in Ni3Al with increasing temperature. A Ni3Al based alloy hardened by disperse phase of disordered γ has been obtained by controlling chemical composition and treating processes. The peak temperature of strain hardening rate of this alloy is increased due to the fine disperse phase of disordered γ, which causes the reductions of the movability of the superdislocations and the dynamic recovery in Ni3Al展开更多
The microstructure of alloy Ti 3Al 10Nb 3V 1Mo after heated at 1170℃ for 1 h and cooled to room temperature at different rates was investigated by TEM. The result showed that W.Q. microstructure consisted of sing...The microstructure of alloy Ti 3Al 10Nb 3V 1Mo after heated at 1170℃ for 1 h and cooled to room temperature at different rates was investigated by TEM. The result showed that W.Q. microstructure consisted of single B2 phase, A.C. microstructure consisted of B2 phase matrix and second phase in some regions of the B2 phase crystal grains, and C.C. and F.C. microstructure appeared as a Widmannstatten structure consisting of coarse α 2 phase plates and β phase stripes between the plates. With the decreasing of colling rate, the tension strength was obviously decreased and the plasticity was slightly increased at room temperature.展开更多
A new technology was developed to recover multiple valuable elements from the spent Al2O3-based catalyst by X-ray phase analysis and exploratory experiments. The experimental results show that in the condition of roas...A new technology was developed to recover multiple valuable elements from the spent Al2O3-based catalyst by X-ray phase analysis and exploratory experiments. The experimental results show that in the condition of roasting temperature of 750℃ and roasting time of 30 min, molar ratio of Na2O to Al2O3 of 1.2, the leaching rates of alumina, vanadium and molybdenum in the spent catalyst are 97.2%, 95.8% and 98.9%, respectively. Vanadium and molybdenum in sodium aluminate solution can be recovered by precipitators A and B, and the precipitation rates of vanadium and molybdenum are 94.8% and 92.6%. Al（OH）3 was prepared from sodium aluminate solution in the carbonation decomposition process, and the purity of Al2O3 is 99.9% after calcination, the recovery of alumina reaches 90.6% in the whole process; the Ni-Co concentrate was leached by sulfuric acid, a nickel recovery of 98.2% and cobalt recovery over 98.5% can be obtained under the experimental condition of 30% H2SO4, 80℃, reaction time 4 h, mass ratio of liquid to solid 8, stirring rate 800r/min.展开更多
60% white corundum used for aggregate, 5% aluminium powder for fixed additions and 35% various additives for matrix were prepared for specimens 1#,2#,3#. They were mixed uniformly with the suitable resin as a binder a...60% white corundum used for aggregate, 5% aluminium powder for fixed additions and 35% various additives for matrix were prepared for specimens 1#,2#,3#. They were mixed uniformly with the suitable resin as a binder and pressed under pressure of 315 ton forging press, then dried at 200℃ for 24 h. Effects of various additives on 1500 ℃×2 h creep properties of Al3CON reinforced corundum composite were researched. The experimenal results show that creep coefficients of specimens 1#,2#,3# at 1500 ℃×2 h are 1.4×10^- 4, -9.4×10^-4, -22.6×10^-4, respectively. Crushing strength of the slide plate added with suitable additive A after fired at 1500 ℃ ×3 h reaches to 225 MPa, the creep rate is positive all the time from 0% to 0.014% at 1500 ℃ for 2 h. The microstructure result analysis shows that reinforced phases of Al3CON fiber composite have been formed after fired with Al powder in coke at high temperatures for specimen 1#, and the strength of the composite is increased. The hot modulus of rupture is up to 59 MPa at 1400 ℃ and the RUL is obviously higher than that at 1700 ℃. Its service life is two times as that of Al2O3-C slide plate when used in the process of pouring steel. The mechanism of creep rate resistance of the composites can be discovered by means of SEM and EDAX analysis. It is concluded that the active Al3CON and Al2O3 multiphases that were formed by N2 in gas, C, Al and Al2O3 inside the matrix of the composites during in-situ reaction,which gives the composites outstanding creep rate resistance for the dense zone resuiting from Al3CON oxidation that inhibits contraction at the high temperature. Besides, the matrix will turn into the multiphase with high refractoriness, N content and its Al3CON reinforced fiber will further increase accordingly. In addition, Al3CON formed by Al2O3 and C, Al in the matrix with N2 in gas will inhibit the creep rate and also greatly improve the creep rate resistance of the composites.展开更多
The influence of alumina volume percent and solution heat-treatment on the corrosion behaviour of Al (6063) composites and its monolithic alloy in salt water, basic and acidic environments is investigated. Al (6063) ...The influence of alumina volume percent and solution heat-treatment on the corrosion behaviour of Al (6063) composites and its monolithic alloy in salt water, basic and acidic environments is investigated. Al (6063) – Al2O3 particulate composites containing 6, 9, 15, and 18 volume percent alumina were produced by adopting two step stir casting. Mass loss and corrosion rate measurements were utilized as criteria for evaluating the corrosion behaviour of the composites. It is observed that Al (6063) – Al2O3 composites exhibited excellent corrosion resistance in NaCl medium than in the NaOH and H2SO4 media. The unreinforced alloy exhibited slightly superior corrosion resistance than the composites in NaCl and NaOH media but the composites had better corrosion resistance in H2SO4 medium. Furthermore, solution heat-treatment resulted in improved corrosion resistance for both the composites and the unreinforced alloy while the effect of volume percent alumina on corrosion resistance did not follow a consistent trend.展开更多
The loading tests of Fe 3Al under tensile impact have been carried out by a self designed rotating circular disk tensile impact apparatus. An experimental study of Fe 3Al in the strain rate range from 80 s -1 to 1 200...The loading tests of Fe 3Al under tensile impact have been carried out by a self designed rotating circular disk tensile impact apparatus. An experimental study of Fe 3Al in the strain rate range from 80 s -1 to 1 200 s -1 was performed and the complete stress strain curves under tensile impact were obtained. On the basis of the experimental results, it is believed that Fe 3Al obviously exists dynamic ductility and effect of strain rate hardening. The yield strength, ultimate strength and failure strain increase with increasing strain rate. Based on the linear least squares fit, the relationship between the yield strength, ultimate strength, failure strain and strain rate under tensile impact was obtained. At the same time, one dimensional macro constitutive equation for Fe 3Al under tensile impact according to the elastic viscoplastic constitutive theory was derived.展开更多
The superplasticity of an Al203p/6061Al composite, fabricated by powder metallurgy techniques, has been investigated. Instead of any special thermomechanical processing or hot rolling, simple ...The superplasticity of an Al203p/6061Al composite, fabricated by powder metallurgy techniques, has been investigated. Instead of any special thermomechanical processing or hot rolling, simple hot extrusion has been employed to obtain a fine grained structure before superplastic testing. Superplastic tensile tests were performed at strain rates ranging from 10-2 to 10-4 s-1 and at temperatures from 833 to 893 K. A maximum elongation of 200% was achieved at a temperature of 853 K and an initial strain rate of 1.67×103 s-1. The highest value obtained for the strain rate sensitivity index (in) was 0.32. Differential scanning calorimeter was used to ascertain the possibility of any partial melting in the vicinity of optimum superplastic temperature. These results suggested that no liquid phase existed where maximum elongation was achieved and deformation took place entirely in the solid state.展开更多
Recently, Hsieh and Horng [1] published the paper entitled as above. In section 3 results and discussion, the authors mentioned the first and the second order kinetic models without any quotations. In fact these two k...Recently, Hsieh and Horng [1] published the paper entitled as above. In section 3 results and discussion, the authors mentioned the first and the second order kinetic models without any quotations. In fact these two kinetic models have been published [2-5]. In order to distinguish a kinetics model based on the ad- sorption capacity of a solid from the one based on the concentration of a solution, Lagergren＇s first-order rate equation has been called pseudo-first-order [6-7]. The Lagergren＇s equation has been widely cited, but there are far more mistakes made in the quotation and in the reference section of papers, including the title, the author＇s name, journal title, year of publishing, volume, and page number [3]. In addition, the second order kinetic expression for the adsorption systems of divalent metal ions using sphagnum moss peat has been reported by Ho [8].展开更多
Al80Ni6 Y8 Co4 Cu2 amorphous ribbons were isothermally annealed and a mixed structure consisting of α-Al particle with a size of less than 15nm and Al3Ni compound with a size of about 30nm was obtained. The crystall...Al80Ni6 Y8 Co4 Cu2 amorphous ribbons were isothermally annealed and a mixed structure consisting of α-Al particle with a size of less than 15nm and Al3Ni compound with a size of about 30nm was obtained. The crystallization kinetics of Al80Ni6 Y8 Co4 Cu2 amorphous alloy shows that the precipitation of α-Al particles is the growth process controlled by diffusion of the solute elements rejected from the growing crystals. By quenching at different cooling rates, a mixed structure consisting of nanoscale α-Al particles and the remaining glass matrix or structure consisting of nanoscale particle (Al phase or Al3Ni compound) with a size of about 100nm was formed. The addition of Co elements and Cu elements to Al-Ni-Y alloy systems increases the glass formation ability of the alloy and the thermal stability of the supercooled liquid region against crystallization, which results from significant difference of atomic size, strong bonding nature among constituent elements and the low diffisivity of the solute elements due to the concentration gradient in the growing front of crystals.展开更多
文摘Investigations have been made on the effects of temperature and fine disperse phase of disordered γ on strain hardening rate of Ni3Al based alloy. The result is found that there exists a peak temperature for the strain hardening rate of Ni3Al based alloy below the peak temperature of its yield strength. Analysis shows that the appearance of the peak temperature of strain hardening rate is caused by both the decreasing of the movability of <101> superdislocations on {111}slip plane and the increasing of the dynamic recovery in Ni3Al with increasing temperature. A Ni3Al based alloy hardened by disperse phase of disordered γ has been obtained by controlling chemical composition and treating processes. The peak temperature of strain hardening rate of this alloy is increased due to the fine disperse phase of disordered γ, which causes the reductions of the movability of the superdislocations and the dynamic recovery in Ni3Al
文摘The microstructure of alloy Ti 3Al 10Nb 3V 1Mo after heated at 1170℃ for 1 h and cooled to room temperature at different rates was investigated by TEM. The result showed that W.Q. microstructure consisted of single B2 phase, A.C. microstructure consisted of B2 phase matrix and second phase in some regions of the B2 phase crystal grains, and C.C. and F.C. microstructure appeared as a Widmannstatten structure consisting of coarse α 2 phase plates and β phase stripes between the plates. With the decreasing of colling rate, the tension strength was obviously decreased and the plasticity was slightly increased at room temperature.
基金the financial supports from the National Natural Science Foundation of China(Nos.11772332,11790292,11727803,11988102)the Strategic Priority Research Program of the Chinese Academy of Sciences(No.XDB22040501)the Opening Fund of State Key Laboratory of Nonlinear Mechanics,China。
基金Project(2003 UDBEA00C020) supported by the Collaborative Project of School and Province of Yunnan Province
文摘A new technology was developed to recover multiple valuable elements from the spent Al2O3-based catalyst by X-ray phase analysis and exploratory experiments. The experimental results show that in the condition of roasting temperature of 750℃ and roasting time of 30 min, molar ratio of Na2O to Al2O3 of 1.2, the leaching rates of alumina, vanadium and molybdenum in the spent catalyst are 97.2%, 95.8% and 98.9%, respectively. Vanadium and molybdenum in sodium aluminate solution can be recovered by precipitators A and B, and the precipitation rates of vanadium and molybdenum are 94.8% and 92.6%. Al（OH）3 was prepared from sodium aluminate solution in the carbonation decomposition process, and the purity of Al2O3 is 99.9% after calcination, the recovery of alumina reaches 90.6% in the whole process; the Ni-Co concentrate was leached by sulfuric acid, a nickel recovery of 98.2% and cobalt recovery over 98.5% can be obtained under the experimental condition of 30% H2SO4, 80℃, reaction time 4 h, mass ratio of liquid to solid 8, stirring rate 800r/min.
基金Funded by the National Torch Plan of China (No. 2005EB031110)the Key Scientific and Technical Innovation Project of Xi’an University of Ar-chitecture and Technology ( No. ZX 0402)
文摘60% white corundum used for aggregate, 5% aluminium powder for fixed additions and 35% various additives for matrix were prepared for specimens 1#,2#,3#. They were mixed uniformly with the suitable resin as a binder and pressed under pressure of 315 ton forging press, then dried at 200℃ for 24 h. Effects of various additives on 1500 ℃×2 h creep properties of Al3CON reinforced corundum composite were researched. The experimenal results show that creep coefficients of specimens 1#,2#,3# at 1500 ℃×2 h are 1.4×10^- 4, -9.4×10^-4, -22.6×10^-4, respectively. Crushing strength of the slide plate added with suitable additive A after fired at 1500 ℃ ×3 h reaches to 225 MPa, the creep rate is positive all the time from 0% to 0.014% at 1500 ℃ for 2 h. The microstructure result analysis shows that reinforced phases of Al3CON fiber composite have been formed after fired with Al powder in coke at high temperatures for specimen 1#, and the strength of the composite is increased. The hot modulus of rupture is up to 59 MPa at 1400 ℃ and the RUL is obviously higher than that at 1700 ℃. Its service life is two times as that of Al2O3-C slide plate when used in the process of pouring steel. The mechanism of creep rate resistance of the composites can be discovered by means of SEM and EDAX analysis. It is concluded that the active Al3CON and Al2O3 multiphases that were formed by N2 in gas, C, Al and Al2O3 inside the matrix of the composites during in-situ reaction,which gives the composites outstanding creep rate resistance for the dense zone resuiting from Al3CON oxidation that inhibits contraction at the high temperature. Besides, the matrix will turn into the multiphase with high refractoriness, N content and its Al3CON reinforced fiber will further increase accordingly. In addition, Al3CON formed by Al2O3 and C, Al in the matrix with N2 in gas will inhibit the creep rate and also greatly improve the creep rate resistance of the composites.
文摘The influence of alumina volume percent and solution heat-treatment on the corrosion behaviour of Al (6063) composites and its monolithic alloy in salt water, basic and acidic environments is investigated. Al (6063) – Al2O3 particulate composites containing 6, 9, 15, and 18 volume percent alumina were produced by adopting two step stir casting. Mass loss and corrosion rate measurements were utilized as criteria for evaluating the corrosion behaviour of the composites. It is observed that Al (6063) – Al2O3 composites exhibited excellent corrosion resistance in NaCl medium than in the NaOH and H2SO4 media. The unreinforced alloy exhibited slightly superior corrosion resistance than the composites in NaCl and NaOH media but the composites had better corrosion resistance in H2SO4 medium. Furthermore, solution heat-treatment resulted in improved corrosion resistance for both the composites and the unreinforced alloy while the effect of volume percent alumina on corrosion resistance did not follow a consistent trend.
文摘The loading tests of Fe 3Al under tensile impact have been carried out by a self designed rotating circular disk tensile impact apparatus. An experimental study of Fe 3Al in the strain rate range from 80 s -1 to 1 200 s -1 was performed and the complete stress strain curves under tensile impact were obtained. On the basis of the experimental results, it is believed that Fe 3Al obviously exists dynamic ductility and effect of strain rate hardening. The yield strength, ultimate strength and failure strain increase with increasing strain rate. Based on the linear least squares fit, the relationship between the yield strength, ultimate strength, failure strain and strain rate under tensile impact was obtained. At the same time, one dimensional macro constitutive equation for Fe 3Al under tensile impact according to the elastic viscoplastic constitutive theory was derived.
基金This work was supported by the National Natural Science Foundation of China,under grant No.59781004.
文摘The superplasticity of an Al203p/6061Al composite, fabricated by powder metallurgy techniques, has been investigated. Instead of any special thermomechanical processing or hot rolling, simple hot extrusion has been employed to obtain a fine grained structure before superplastic testing. Superplastic tensile tests were performed at strain rates ranging from 10-2 to 10-4 s-1 and at temperatures from 833 to 893 K. A maximum elongation of 200% was achieved at a temperature of 853 K and an initial strain rate of 1.67×103 s-1. The highest value obtained for the strain rate sensitivity index (in) was 0.32. Differential scanning calorimeter was used to ascertain the possibility of any partial melting in the vicinity of optimum superplastic temperature. These results suggested that no liquid phase existed where maximum elongation was achieved and deformation took place entirely in the solid state.
文摘Recently, Hsieh and Horng [1] published the paper entitled as above. In section 3 results and discussion, the authors mentioned the first and the second order kinetic models without any quotations. In fact these two kinetic models have been published [2-5]. In order to distinguish a kinetics model based on the ad- sorption capacity of a solid from the one based on the concentration of a solution, Lagergren＇s first-order rate equation has been called pseudo-first-order [6-7]. The Lagergren＇s equation has been widely cited, but there are far more mistakes made in the quotation and in the reference section of papers, including the title, the author＇s name, journal title, year of publishing, volume, and page number [3]. In addition, the second order kinetic expression for the adsorption systems of divalent metal ions using sphagnum moss peat has been reported by Ho [8].
文摘Al80Ni6 Y8 Co4 Cu2 amorphous ribbons were isothermally annealed and a mixed structure consisting of α-Al particle with a size of less than 15nm and Al3Ni compound with a size of about 30nm was obtained. The crystallization kinetics of Al80Ni6 Y8 Co4 Cu2 amorphous alloy shows that the precipitation of α-Al particles is the growth process controlled by diffusion of the solute elements rejected from the growing crystals. By quenching at different cooling rates, a mixed structure consisting of nanoscale α-Al particles and the remaining glass matrix or structure consisting of nanoscale particle (Al phase or Al3Ni compound) with a size of about 100nm was formed. The addition of Co elements and Cu elements to Al-Ni-Y alloy systems increases the glass formation ability of the alloy and the thermal stability of the supercooled liquid region against crystallization, which results from significant difference of atomic size, strong bonding nature among constituent elements and the low diffisivity of the solute elements due to the concentration gradient in the growing front of crystals.
