Study on Roasting Decomposition of Mixed Rare Earth Concentrate in CaO-NaCl-CaCl_2

The decomposed process of bastnaesite, monazite and mixed rare earth concentrate in CaO-CaCl-CaCl2 was studied by means of TG-DTA method. The relationship among decomposition ratio, roasting temperature, and CaO-NaCl addition was studied by the quadratic regression orthogonal analysis, and then the regression equation was obtained. Through analysis, the optimum process conditions of mixed rare earth concentrate decomposed by CaO-CaCl-CaCl2 were obtained as follows: roasting temperature: 700℃, CaO addition: 15%, NaCl-CaCl2 addition: 10%, roasting time: 60 min, the decomposition ratio: 91.3%.

Study on Escaping Fluorine Inhibition in Calcining Process of Mixed Rare Earth Concentrate

GC technology was used to study escaping fluorine in calcined process of mixed rare earth concentrate. The mixed rare earth concentrate and it adding assistant of CaO-NaCl-CaCl2 were calcined at 400～750 ℃ for 30～120 min, and then total amount of fluorine, exhausting ratio of fluorine, decomposition ratio and the component were determined. The results showed that adding CaO-NaCl-CaCl2 the decomposition ratio was up to 90% at 700 ℃ in 1 h, and the escaping ratio of fluorine decreased from 29.52% to 0.948%. The average inhabitation ratio was 98.39%. This method supplied basis for low energy and clean decomposition of mixed rare earth concentrate.

Decomposing scheelite and scheelite-wolframite mixed concentrate by caustic soda digestion

Scheelite and scheelite-wolframite mixed concentrates with different grades were decomposed by caustic soda digestion, and the effects of caustic soda（NaOH） dosage, the ratio of water to ore and the stirring rate on tungsten recovery were studied. The results show that under the conditions that the ratio of water to ore is （0.8,） stirring rate is 500 r·min-1 and the heating time is 2.0 h at （160 ℃,） the recovery of tungsten reaches 98% for scheelite （w（WO3） is （65.04%）） and wolframite containing high proportion of calcium （w（WO3） is 65.58%, w（Ca） is （7.53%）,） when caustic soda dosage is 2.2 and 2.0 times of theoretical value, respectively; the recovery of tungsten can be more than 98%,98% and 96% respectively for low-grade scheelite-wolframite mixed concentrate with （55.78%,） 45.32% and 25.21% WO3, when caustic soda dosage is 2.6,3.2 and 5.5 times of theoretical value, respectively.

Effect of Pelleted Total Mixed Ration with Different Concentrate-roughage Ratios on Production Performance and Serum Biochemical Parameters of Fattening Hainan Black Goats

[Objective] This paper was to study effects of pelleted total mixed ration with different concentrate-roughage ratios on production performance and serum biochemical parameters of fattening Hainan black goats.[Method] Thirty-six fattening Hainan black goats with the same genetic background and similar initial weight of(14.08±0.13) kg were randomly assigned into three treatments. Goats were fed with Juncao + concentrate(control group), pelleted total mixed ration I(concentrate: roughage 50 ∶50, group Ⅰ) and Ⅱ(concentrate: roughage 45∶55, group Ⅱ), respectively. The test lasted 45 d.[Result] The final weight, daily gain and feed intake of rams in experimental group Ⅰ were significantly higher than those of control group and experimental group Ⅱ(P<0.05);the final weight and daily gain of rams in experimental group Ⅰ were also markedly higher than those of experimental group Ⅱ(P<0.05);the feed/gain of rams in experimental group Ⅰ was significantly lower than those in control group and experimental group Ⅱ(P<0.05). The feed gain cost of rams in experimental group Ⅰ was markedly lower than that in experimental group Ⅱ( P<0.05), but was significantly higher than that in experimental group Ⅰ(P<0.05);the gross profit of rams in experimental group Ⅰ was significantly higher than those in control group and experimental group Ⅱ(P<0.05). Compared with control group and experimental group Ⅱ, the serum total protein and glucose lev-els in experimental group Ⅱ increased significantly(P<0.05), but the urea nitrogen content reduced(P>0.05).[Conclusion] When the concentrateroughage ratio of pelleted total mixed ration was 50∶50, the fattening effect of Hainan black goat was better, and the serum total protein and glucose levels were evidently improved.

Bio-dissolution of Cu,Mo and Re from molybdenite concentrate using mix mesophilic microorganism in shake flask

The application of the response surface methodology and the central composite design（CCD） technique for modeling and optimization of the influence of some operating variables on copper,molybdenum and rhenium recoveries in a bioleaching process was investigated.Three main bioleaching parameters,namely pH,solid concentration and inoculum percent,were changed during the bioleaching tests based on CCD.The ranges of the bioleaching process variables used in the design were as follows：pH1.46-2.14,solid concentration 0.95%-11.05%,and inoculum percent 1.59%-18.41%.A total of 20 bioleaching tests were carried out by the CCD method according to software-based designed matrix.Empirical model equations were developed according to the copper,molybdenum and rhenium recoveries obtained with these three parameters.Model equations of responses at the base of parameters were achieved by using statistical software.The model equations were then individually optimized by using quadratic programming to maximize copper,molybdenum and rhenium recoveries individually within the experimental range.The optimum conditions for copper recovery were pH 1.68,solid concentration 0.95% and the inoculum 18.41%（v/v）,while molybdenum and rhenium recoveries were 2.18% and 24.41%,respectively.The predicted values for copper,molybdenum and rhenium recoveries were found to be in good agreement with the experimental values.Also jarosite formation during bioleaching tests was also investigated.

Selective leaching of calcium from mechanically activated mixed rare earth concentrate

The loss of rare earths(REs)takes place during the pre-decalcification process of mixed rare earth concentrate.In an effort to reduce such RE loss,a novel idea to improve the leaching selectivity of Ca to REs by applying selective mechanical activation was proposed.First,regarding the key minerals affecting the leaching selectivity of Ca to REs,the differences in the mechanical activation behaviors of CaF_(2) and REFCO_(3) were studied,and we find that the lattice strain of CaF_(2) increases from 0.21%to 0.42%,whereas that of REFCO_(3) increases from 0.31%to 0.40%.Notably,CaF_(2) demonstrates a larger lattice strain than REFCO_(3),indicating greater mechanical activation energy storage and higher leaching activity.Next,the HCl leaching process was studied.A significant leaching selectivity of Ca to REs,from 21.6 to 35.1,is achieved through mechanical activation.The Ca leaching rate reaches 80.7%when the RE loss is 2.3%in the activated sample.This study provides an novel approach for achieving selective extraction of specific components via mechanical activation pretreatment.

Reaction process of monazite and bastnaesite mixed rare earth minerals calcined by CaO-NaCl-CaCl_2

The decomposition reactions of monazite and bastnaesite mixed rare earth minerals calcined by CaO-NaCl-CaCl2 were studied by means of TG-DTA and XRD. The results show that the process of the minerals decomposed by CaO involves two steps. The first step occurs in the temperature range of 425-540 ℃, and the main reactions are bastnaesite decomposition, i.e. REOF reacts with CaO to produce RE2O3 and CaF2, and Ce2O3 is oxidized to CeO2. During this step, CaCO3 is formed at about 500 ℃. The second step takes place in the temperature range of 610-700 ℃, and the reactions are monazite decomposition into RE2O3, Ca5F(PO4)3 and Ca3(PO4)2 by CaO and CaF2. In this process, the decomposition ability is improved because CaO from CaCO3 decomposing has high chemical activity. In calcining process, the new formed Ca5F(PO4)3 restrains fluorine that can escape in form of gaseous compound. The decomposition ratio of the mixed rare earth minerals reaches 90.8% at 700 ℃.

Mixed Conduction in BaCe0.8Pr0.2O3-α Ceramic

BaCe0.8Pr0.2O3-α ceramic was synthesized by high temperature solid-state reaction. The structural characteristics and the phase purity of the crystal were determined using powder X-ray diffraction analysis. By using the methods of AC impedance spectroscopy, gas concentration cell and electrochemical pumping of hydrogen, the conductivity and ionic transport number of BaCe0.8Pr0.2O3-α were measured, and the electrical conduction behavior of the material was investigated in different gases in the temperature range of 500-900℃. The results indicate that the material was of a single perovskite-type orthorhombic phase. From 500℃ to 900 ℃, electronic-hole conduction was dominant in dry and wet oxygen, air or nitrogen, and the total conductivity of the material increased slightly with increasing oxygen partial pressure in the oxygen partial pressure range studied. Ionic conduction was dominant in wet hydrogen, and the total conductivity was about one or two orders of magnitude higher than that in hydrogen-free atmosphere （oxygen, air or nitrogen）

Syntheses of Coordination Compounds of 2-Amino-3-Methylbutanoic Acid Their Mixed Ligand Complexes and Antibacterial Activities

Coordination compounds of 2-amino-3-methylbutanoic acid were synthesized with chromium(III) and oxovanadium(IV) ions. M:L;1:2. Adducts of these complexes using 1,10-phenantroline and ethylenediamine were further synthesized, M:L, (1:2). These compounds were characterized using electronic, infra-red spectrophotometry, magnetic susceptibility measurement and percentage metal analyses. The zones of inhibition and minimum inhibitory concentrations of the compounds against eight microbes were studied. The results obtained indicated an octahedral geometry for the Cr(III) complexes, indicative of additional coordination of two water molecules. On the other hand a square pyramid geometry was obtained for the binary oxovanadium complex and its 1,10-phenantroline adduct. However, for the oxovanadium ethylenediamine adduct a distorted octahedral geometry was proposed. The result for the antibacterial studies indicated that both mixed ligand complexes of 1,10-phenantroline exhibited good antibacterial activity, and in some cases better activity than the standard, streptomycin.

Experimental investigation of the mixing efficiency via intensity of segregation along axial direction of a rotating bar reactor

As a significant index to evaluate the mixing efficiency,studying the concentration distribution is directly related to the intensity of segregation(I_(s)).In this work,the I_(s) of the mixture composed of NaCl solutionwater was investigated experimentally in a rotating bar reactor(RBR)by the conductivity method.The results showed that the mixing efficiency was improved along the axial direction from the bottom to the top in the RBR.The concentration distribution at the bottom section was more uneven,and I_(s) was higher compared with the top section,which decreased from 6.53×10^(-5)to 1.57×10^(-7).With the increase of rotational speed from 0 to 700 r·min^(-1),I_s at the bottom and top sections decreased from 4.27×10^(-3)to 7.10×10^(-5)and from 1.93×10^(-3)to 7.29×10^(-7),respectively.The increases flow rate of solution A,and the decreases of concentration of NaCl and flow rate of solution B gave rise to the reduction of I_(s),signifying an improved mixing efficiency.The results revealed that the conductivity method used in this paper has high efficiency and low cost to measure the I_(s),which indicates a promising prospect for estimating reactors'mixing performance.

Influence of mixed layer depth on chlorophyll-a concentration in the Southern Ocean

The element iron limitation is one of the crucial factors contributing to high nutrient low chlorophyll in the Southern Ocean(SO).Mixed layer dynamics regulate the availability of iron to phytoplankton.In this paper,we investigate the influence of surface iron supplementation triggered by the mixed layer depth(MLD)variation on chlorophyll-a(Chl-a)concentration in the SO on seasonal and interannual timescales.This analysis is based on the Biogeochemical Southern Ocean State Estimate for the period from 2013 to 2021.We provide a comprehensive and systematic mapping of the regions within the SO,where Chl-a is affected by iron input related to MLD deepening.The relationship between the MLD and the Chl-a varies with the latitude on the seasonal time scale.Both the MLD and sea ice melting affect the distribution of Chl-a.On the interannual scale,iron supply due to MLD deepening occurs primarily north of 60°S.Horizontal advection-induced entrainment enhances the surface iron input during the austral summer,which favors Chl-a increase.In addition to the MLD,the melting of sea ice and cooling of the sea surface can also alter iron input and subsequently affect Chl-a distribution in the austral summer.During the austral winter,entrainment can boost iron stocks,stimulating a subsequent spring increase of Chl-a in the SO.Furthermore,sea surface temperature declines during the austral winter,promoting an increased iron supply and creating favorable conditions for the subsequent spring Chl-a increase in the SO.

综掘工作面混合式风流调控下的粉尘沉降研究

煤矿掘进过程中粉尘聚集严重,目前针对综掘工作面混合式风流调控下粉尘沉降规律及优化的研究还不够深入。基于混合式风流调控系统,依托陕煤集团神木柠条塔矿业有限公司综掘工作面,分析了压风口距工作面距离、压风口右偏角度、压风口口径、抽风口距工作面距离和压抽比等混合式风流调控参数对粉尘沉降规律的影响:随着压风口距工作面距离增加,司机处和回风侧行人呼吸带截面大颗粒粉尘占比先增后减再增,小颗粒粉尘占比增加;随着压风口右偏角度增加,司机处和回风侧行人呼吸带截面大颗粒粉尘占比变化明显;随着压风口口径增加,司机处截面小颗粒粉尘占比先增后减再增,回风侧行人呼吸带截面大颗粒粉尘占比先增后减;随着抽风口距工作面距离增加,司机处截面大颗粒粉尘占比先增后减,小颗粒粉尘占比先增后减再增,回风侧行人呼吸带截面粉尘粒径分布变化不大;随着压抽比增大,司机处和回风侧行人呼吸带截面小颗粒粉尘占比减小。以上述风流调控各参数为自变量,回风侧行人呼吸带全尘平均浓度和司机处呼尘平均浓度最低为优化目标,建立了粉尘沉降优化回归模型,利用粒子群优化算法求解模型,得到最优风流调控方案:压风口距工作面距离为8.9 m,压风口右偏角度为14.8°,压风口口径为0.9 m,抽风口距工作面距离为4.3 m,压抽比为1.1。搭建了风流调控下粉尘沉降实验平台,实验结果表明:测试值与粉尘沉降优化回归模型的模拟值误差在13%以内,验证了模型的准确性;优化后粒径为71~100μm的粉尘受风流调控参数影响明显,沉降在掘进机前方;优化后回风侧行人呼吸带全尘平均浓度和司机处呼尘平均浓度分别降低了47.4%和42.4%,降尘效果明显。

基于不同群体药动学分析工具建立真实世界丙戊酸群体药代动力学模型

目的:基于NONMEM和MONOLIX 2种不同群体药动学分析工具建立真实世界丙戊酸群体药动学模型(PPK),探索可能影响丙戊酸血药浓度的潜在协变量,为癫痫患者使用丙戊酸提供科学依据。方法:回顾性收集2021年1月—2022年12月南京医科大学第二附属医院收治的167例癫痫患者239个丙戊酸稳态血药浓度数据资料,按随机数字表法将其分为模型组(n=111)与验证组(n=56)。2种群体药动学分析工具同时建立适合真实世界的群体药动学模型,采用拟合度优度诊断、可视化预测检验对所得的模型进行内部验证和外部验证,评估模型的预测能力。结果:该群体药动学为一室模型,在使用NONMEM软件建立的最终模型中纳入了联合用药(DDI)-美罗培南和给药方式(ROUTE)作为协变量;而在使用MONOLIX软件建立的最终模型中纳入了联合用药(DDI)-美罗培南和体质量(BW)作为协变量。与此同时,与NONMEM相比较,MONOLIX软件所得到的最终模型具有更好的精密度和准确度。结论:本研究初步构建了适用于癫痫患者给予丙戊酸剂量指导的群体药动学模型。

基于物联网的电镀铬镍混合废水浓度监控系统

监测废水中的铬和镍浓度有助于早期发现和处理潜在的问题,减少对自然环境和水资源的污染风险。为此,设计了基于物联网架构的电镀铬镍混合废水浓度监控系统。在指挥层中使用LoRaWAN通信方式连接电化学传感器和监控系统,监控系统可以实时采集废水中的铬和镍浓度数据。在网络层中使用箱线图对指挥层中采集的数据进行异常值识别,并去除这些异常值。为保证数据的安全性和稳定性,通过物联网技术中的监控系统软件协议代码将数据传输至云平台。在云平台中利用孤独森林算法对传输到云平台的数据进行模式识别和监测,通过感知层将废水浓度数据以可视化的形式展示出来,使用户能够直观地了解混合废水的浓度情况。实验结果表明,本文系统的监测准确度保持在95%以上,且数据传输效率保持在96%以上,具有较高监测准确度的同时具有良好的运行性能。

富氧铜侧吹熔池熔炼炉内流场与混匀效率模拟研究

鉴于冶金炉窑的高温与不可见性,大多测量手段受到限制,所以本文采用数值模拟对高温下富氧铜侧吹熔炼炉内的流场与混匀效率进行分析。受浮力影响,侧吹气流具有区域性的特点,主要对气流上升轨迹周围熔体直接搅拌,熔池中心存在低速区域,速度小于0.1 m/s。受侧吹气流反冲作用,壁面高应力区域集中在喷嘴附近以及气泡上浮路径周围,该区域壁面应力是相邻喷枪间壁面应力的2~3倍,炉衬更易受损。通过熔池内环流分布状态,沿喷枪轴线方向将熔池划分为高速喷吹区与环流搅拌区。其中环流搅拌区为主反应区,速度小于1 m/s,但速度分布更加均匀,组分的均混时间为34.10 s。平行环流喷吹技术对熔池的混合效率改善最明显,湍流黏度为原工况的1.51倍,均混时间相对降低62.18%。

黑龙江某铜钼混合精矿絮凝沉降性能及机理研究

黑龙江某铜钼混合精矿矿物成分复杂,矿样中-30μm粒级含量占45.56%,微细颗粒含量高,该精矿因成分复杂且微细粒含量高导致精矿浓缩池的絮凝沉降作业面临着沉降慢、溢流浊度高的巨大难题。为探究该精矿的絮凝沉降性能及相关机理,首先,对该样品进行单因素絮凝沉降试验,以沉降高度和上清液浊度为指标考察絮凝剂分子量、絮凝剂浓度、絮凝剂单耗量、矿浆浓度和矿浆pH值对其絮凝沉降效果的影响;其次,利用傅里叶红外光谱对沉降产物进行分析,探究矿物颗粒与絮凝剂之间的配位模式和作用方式;最后,借助分子动力学模拟结果分析样品中各矿物与絮凝剂分子和水分子之间的作用关系。物理结果表明,该样品在阴离子型聚丙烯酰胺(APAM)分子量1000万、配制浓度1.60‰、单耗量25g/t、矿浆浓度25%和矿浆pH=11时絮凝沉降效果最优;红外谱图分析结果表明,APAM与矿物表面发生了氢键吸附和化学吸附;分子动力学结果表明,4种主要矿物与APAM的絮凝吸附均为自发过程,且APAM分子在4种矿物表面均紧密分布,而水分子主要分布在黄铜矿和辉钼矿表面。本文研究结果可为微细粒铜钼混合精矿的絮凝沉降工艺及新型絮凝剂分子的设计开发提供科学依据。

HYIC捕收剂强化鞍千混合磁选精矿反浮选效果试验

鞍千选矿厂为了优化选别工艺中的反浮选效果,取浮选入选的混合磁选精矿进行浮选试验,进行了抑制剂、活化剂、捕收剂用量及常规捕收剂TD-Ⅱ与新型捕收剂HYIC浮选效果对比试验。试验结果表明:固定矿浆pH值为11.5、抑制剂淀粉用量1200 g/t、活化剂CaO用量500 g/t、粗选捕收剂用量800 g/t、精选捕收剂用量300 g/t,采用常规捕收剂TD-Ⅱ时,闭路试验获得了精矿铁品位68.20%、铁回收率88.73%的选别指标;采用新型捕收剂HYIC时,闭路试验获得了精矿铁品位68.25%、铁回收率90.04%的选别指标;使用捕收剂HYIC比采用捕收剂TD-Ⅱ所获得的浮选精矿产率、铁品位、铁回收率分别高0.91,0.05,1.31个百分点,捕收剂HYIC可以强化反浮选效果,提高选厂的经济效益。

云南某贫细硫化铜矿石选矿工艺优化研究

云南某低品位细粒嵌布的铜矿石铜、硫品位分别为0.161%和9.704%,有价铜矿物嵌布粒度细,铜硫分离富集难度较大。为实现该硫化铜矿石资源的高效开发利用,在选厂原选矿流程及原矿工艺矿物学研究基础上,进行了系统的磨浮试验。结果表明:矿石采用磨矿—1粗2扫铜硫混合浮选—混浮粗精矿再磨—1粗3精2扫铜硫分离浮选闭路流程处理,可获得铜品位14.69%、铜回收率63.15%的铜精矿,硫品位29.16%、硫回收率75.10%的硫精矿,试验铜精矿品位较现场提高近3个百分点,铜回收率提高15个百分点以上,显著优于现场生产指标,达到了理想的综合回收铜硫效果。研究结果可作为工艺流程优化的依据。

焙烧预处理强化钼铜分离试验及机理研究

为解决钼铜混合精矿的铜钼浮选分离难题,以某选厂钼铜混合精矿为研究对象,探究了焙烧预处理对钼、铜浮选分离效果的影响。结果表明:焙烧预处理能有效改善钼铜混合精矿的浮选分离效果,确定的适宜焙烧预处理条件为焙烧温度250℃,焙烧时间30 min。预处理产品采用1粗2精1扫浮选流程处理,可获得钼精矿钼品位为44.30%、钼回收率为36.58%,铜精矿铜品位为14.23%、铜回收率为69.62%。焙烧产品的XRD和SEM-EDS分析结果表明,样品在焙烧过程中,主要矿物辉钼矿和黄铜矿均可发生氧化反应;当焙烧温度为250℃时,黄铜矿的表面氧化程度远高于辉钼矿,从而增大了两者可浮性差异,为有效分离铜、钼矿物分离创造了条件。

钱塘江河口盐官段混合式丁坝修建对水沙及河床影响的实测研究

钱塘江北岸古海塘堤脚加固工程中,辅助围堰施工的临时性管袋黏土混合式丁坝对工程的顺利进行、提高施工效率起着至关重要的作用,然而目前对其周围水沙运动的研究较少,且缺乏相关实测资料。考虑混合式丁坝修建的动态过程,利用无人机拍摄水流视频结合LSPIV(粒子图像测速)处理技术对丁坝修建前、中、后期周围的流场进行分析,并对丁坝附近的地形进行跟踪测量,同时对不同潮差的水流含沙量进行现场测定。结果表明,丁坝具有改变水流方向,减少水流对河岸冲刷的作用,且丁坝越长,挑流作用越明显,为围堰施工提供了较为平缓的水流条件;混合式丁坝对坝后处的促淤效果明显,且坝后地形变化与含沙量密切相关,潮差越大,水体含沙量越高,丁坝后河床淤积幅度越大,有利于提高围堰的施工效率。研究成果对之后相关物理模型和数值模拟的研究提供数据支持。