Growth of RB Population in the Conversion Phase of Chlamydia Life Cycle

Upon infecting a host cell,the reticulate body(RB)form of the Chlamydia bacteria simply proliferates by binary fission for an extended period.Available data show only RB units in the infected cells 20 hours post infection(hpi),spanning nearly half way through the development cycle.With data collected every 4 hpi,conversion to the elementary body(EB)form begins abruptly at a rapid rate sometime around 24 hpi.By modeling proliferation and conversion as simple birth and death processes,it has been shown that the optimal strategy for maximizing the total(mean)EB population at host cell lysis time is a bang-bang control qualitatively replicating the observed conversion activities.However,the simple birth and death model for the RB proliferation and conversion to EB deviates in a significant way from the available data on the evolution of the RB population after the onset of RB-to-EB conversion.By working with a more refined model that takes into account a small size threshold eligibility requirement for conversion noted in the available data,we succeed in removing the deficiency of the previous models on the evolution of the RB population without affecting the optimal bang-bang conversion strategy.

Life Cycle Assessment Introduced by Using Nanorefrigerant of Organic Rankine Cycle System for Waste Heat Recovery

The use of nanorefrigerants in Organic Rankine Cycle(ORC)units is believed to affect the cycle environment performance,but backed with very few relevant studies.For this purpose,a life cycle assessment(LCA)has been performed for the ORC system using nanorefrigerant,the material and energy input,characteristic indicators and comprehensive index of environmental impact,total energy consumption and energy payback time(BPBT)of the whole life cycle of ORC system using Al_(2)O_(3)/R141b nanorefrigerant were calculated.Total environmental comprehensive indexes reveal that ECER-135 index decrease by 1.5%after adding 0.2%Al_(2)O_(3)nanoparticles to R141b.Based on the contribution analysis and sensitivity analysis,it can be found out ORC system manufacturing is of the most critical stage,where,the ECER-135 index of ORC component production is the greatest,followed by the preparation process of R141b,transportation phase,and that of Al_(2)O_(3)nanoparticles preparation is small.The retirement phase which has good environmental benefits affects the result significantly by recycling important materials.Meanwhile,the main cause and relevant suggestion for improvement were traced respectively.Finally,the environmental impacts of various power generations were compared,and results show that the power route is of obvious advantage.Among the renewable energy,ORC system using Al_(2)O_(3)/R141b nanorefrigerant with minimal environmental impact is only 0.67%of coal-fired power generation.The environmental impact of current work is about 14.34%of other nations’PV results.

Carbon footprint accounting for cigar production processes: A life cycle assessment perspective

Although the tobacco industry is a significant contributor to energy consumption and carbon emissions its negative environmental impact has received inadequate attention globally.Cigarette factories are a key link in the tobacco industry’s production chain,and using data provided by a cigarette factory in China we conduct a life cycle assessment to account for the carbon footprint of cigar production in cigarette factories.The results of the assessment show that factory air conditioning is the most important contributor to the environmental load of the cigar manufacturing process,while electricity is the key factor that contributes the greatest envi‐ronmental load across all of the processes in the product life cycle.In addition,packaging,including small boxes and cigarette cartons,has a significant impact on the industry’s environmental footprint due to its use of raw materials.We find the carbon footprint of the entire production process for cigar products to be 383.59 kg CO_(2) eq.Based on our findings,we suggest ways to optimize cigar/cigarette factory processes to re‐duce carbon emissions that can help to promote sustainable development in related industries.

Carbon emissions reduction potentiality for railroad transportation based on life cycle assessment

This study addresses the comparative carbon emissions of different transportation modes within a unified evaluation framework,focusing on their carbon footprints from inception to disposal.Specifically,the entire life cycle carbon emissions of High-Speed Rail(HSR),battery electric vehicles,conventional internal combustion engine vehicles,battery electric buses,and conventional internal combustion engine buses are analyzed.The life cycle is segmented into vehicle manufacturing,fuel or electricity production,operational,and dismantlingrecycling stages.This analysis is applied to the Beijing-Tianjin intercity transportation system to explore emission reduction strategies.Results indicate that HSR demonstrates significant carbon emission reduction,with an intensity of only 24%-32% compared to private vehicles and 47%-89% compared to buses.Notably,HSR travel for Beijing-Tianjin intercity emits only 24% of private vehicle emissions,demonstrating the emission reduction benefits of transportation structure optimization.Additionally,predictive modeling reveals the potential for carbon emission reduction through energy structure optimization,providing a guideline for the development of effective transportation management systems.

Design of Fine Life Cycle Prediction System for Failure of Medical Equipment

The inquiry process of traditional medical equipment maintenance management is complex,which has a negative impact on the efficiency and accuracy of medical equipment maintenance management and results in a significant amount of wasted time and resources.To properly predict the failure of medical equipment,a method for failure life cycle prediction of medical equipment was developed.The system is divided into four modules:the whole life cycle management module constructs the life cycle data set of medical devices from the three parts of the management in the early stage,the middle stage,and the later stage;the status detection module monitors the main operation data of the medical device components through the normal value of the relevant sensitive data in the whole life cycle management module;and the main function of the fault diagnosis module is based on the normal value of the relevant sensitive data in the whole life cycle management module.The inference machine diagnoses the operation data of the equipment;the fault prediction module constructs a fine prediction system based on the least square support vector machine algorithm and uses the AFS-ABC algorithm to optimize the model to obtain the optimal model with the regularized parameters and width parameters;the optimal model is then used to predict the failure of medical equipment.Comparative experiments are designed to determine whether or not the design system is effective.The results demonstrate that the suggested system accurately predicts the breakdown of ECG diagnostic equipment and incubators and has a high level of support and dependability.The design system has the minimum prediction error and the quickest program execution time compared to the comparison system.Hence,the design system is able to accurately predict the numerous causes and types of medical device failure.

Overall Life Cycle Comprehensive Assessment of Pneumatic and Electric Actuator

Pneumatic actuators and electric actuators have almost been applied to all manufacturing industries. The two kinds of actuators can replace each other in most fields, such as the point to point transmission occasion and some rotating occasions. However, there are very few research results about the advantages and disadvantages of two kinds of actuators under the same working conditions so far. In this paper, a novel comprehensive assessment method, named as overall life cycle comprehensive assessment （OLCCA）, is proposed for comparison and assessment of pneumatic and electric actuators. OLCCA contains mechanical properties evaluation （MPE）, life cycle cost analysis based on users （LCCABOU） and life cycle environmental impact analysis （LCEIA） algorithm in order to solve three difficult problems： mechanical properties assessment, cost analysis and environmental impact assessment about actuators. The mechanical properties evaluation of actuators is a multi-objective optimization problem. The fuzzy data quantification and information entropy methods are combined to establish MPE algorithm of actuators. Two kinds of pneumatic actuators and electric actuators with similar bearing capacity and similar work stroke were taken for example to verify the correctness of MPE algorithm. The case study of MPE algorithm for actuators verified its correctness. LCCABOU for actuators is also set up. Considering cost complex structure of pneumatic actuators, public device cost even method （PDCEM） is firstly presented to solve cost division of public devices such as compressors, aftercooler, receivers, etc. LCCABOU method is also effective and verified by the three groups of pneumatic actuators and electric actuators. Finally, LCEIA model of actuators is established for the environmental impact assessment of actuators. LCEIA data collection method and model establishment procedure for actuators are also put forward. With Simapro 7, LCEIA comparison results of six actuators can be obtained： Fossil fuels are the major environmental factor of pneumatic and electric actuators; Environmental impact of electric actuator is large than one of pneumatic actuator under the similar mechanical properties and working conditions of pneumatic and electric actuators. The results are correct and correspond with the actual mechanical properties of actuators. This paper proposes a comprehensive evaluation method of the actuators, which can solve the critical problem that similar electromechanical products are very difficult to be compared with each other from the angle of performance, cost and environment impact.

An Environmental Learning Support System Incorporating the Life Cycle Concept

The need for environmental education, which incorporates the life cycle concept into the learning program, will become increasingly greater all over the world. In the present study, an e-learning system, which is made up of 3 parts including text-based learning materials, quizzes to review the content of the learning materials and CO2 emission simulation, was designed and developed with the purpose of supporting environmental learning. Targeting a wide range of people, the operation period of this system was 1 month. Based on the results of questionnaire survey for users, it was evident that the quiz function and the simulation function of CO2 emission contributed to the efficiency in environmental learning, and the format of the e-learning system was effective and helpful for environmental learning. Additionally, with the users’ awareness related to environmental conservation before and after using the system, significant changes in awareness were seen in areas such as behavioral intention, sense of urgency and sense of connection. Furthermore, as it was revealed that 62% of the total access numbers were from mobile devices, it was effective to prepare an interface optimized for mobile devices enabling users to use the system from their smartphones and tablet PCs.

Life Cycle Assessment and Life Cycle Cost of Waste Management—Plastic Cable Waste

The main driver for recycling cable wastes is the high value of the conducting metal, while the plastic with its lower value is often neglected. New improved cable plastic recycling routes can provide both economic and environmental incentive to cable producers for moving up the “cable plastic waste ladder”. Cradle-to-gate life cycle assessment, LCA, of the waste management of the cable scrap is suggested and explained as a method to analyze the pros and cons of different cable scrap recycling options at hand. Economic and environmental data about different recycling processes and other relevant processes and materials are given. Cable producers can use this data and method to assess the way they deal with the cable plastic waste today and compare it with available alternatives and thus illuminate the improvement potential of recycling cable plastic waste both in an environmental and in an economic sense. The methodology applied consists of: cradle-to-gate LCA for waste material to a recycled material (recyclate);quantifying the climate impact for each step on the waste ladder for the specific waste material;the use of economic and climate impact data in parallel;climate impact presented as a span to portray the insecurities related to which material the waste will replace;and possibilities for do-it-yourself calculations. Potentially, the methodology can be useful also for other waste materials in the future.

Chinese life cycle impact assessment factors

The methodological basis and procedures for determination of Chinese normalization references and weighting factors according to the EDIP-method is described. According to Chinese industrial development intensity and population density, China was divided into three regions and the normalization references for each region were calculated on the basis of an inventory of all of the region's environmental emissions in 1990. The normalization reference was determined as the total environmental impact potential for the area in question in 1990(EP(j)90) divided by the population. The weighting factor was determined as the normalization reference (ER(j)90) divided by society's target contribution in the year 2000 based on Chinese political reduction plans, ER(j)T2000. This paper presents and discuss results obtained for eight different environmental impact categories relevant for China: global warming, stratospheric ozone depletion, acidification, nutrient enrichment, photochemical ozone formation and generation of bulk waste, hazardous waste and slag and ashes.

A techno-economic and life cycle assessment for the production of green methanol from CO_(2): catalyst and process bottlenecks

The success of catalytic schemes for the large-scale valorization of CO_(2) does not only depend on the development of active,selective and stable catalytic materials but also on the overall process design.Here we present a multidisciplinary study(from catalyst to plant and techno-economic/lifecycle analysis)for the production of green methanol from renewable H2 and CO_(2).We combine an in-depth kinetic analysis of one of the most promising recently reported methanol-synthesis catalysts(InCo)with a thorough process simulation and techno-economic assessment.We then perform a life cycle assessment of the simulated process to gauge the real environmental impact of green methanol production from CO_(2).Our results indicate that up to 1.75 ton of CO_(2) can be abated per ton of produced methanol only if renewable energy is used to run the process,while the sensitivity analysis suggest that either rock-bottom H2 prices(1.5$kg1)or severe CO_(2) taxation(300$per ton)are needed for a profitable methanol plant.Besides,we herein highlight and analyze some critical bottlenecks of the process.Especial attention has been paid to the contribution of H2 to the overall plant costs,CH4 trace formation,and purity and costs of raw gases.In addition to providing important information for policy makers and industrialists,directions for catalyst(and therefore process)improvements are outlined.

Green evaluation of microwave-assisted leaching process of high titanium slag on life cycle assessment

A greenness evaluation index and system of microwave-assisted leaching method were established.The effects of the life cycle assessment variables,such as the resource consumption,environment impact,cost,time and quality,were investigated,and the concept of green degree was applied in the production of synthetic rutile.An analytic hierarchy process was utilized to assess matrix of greenness evaluation.The Gauss-Seidel iterative matrix method was employed to solve the assessment matrix and obtain the weights and membership functions of all evaluation indexes.A fuzzy decision-making method was applied to build the greenness evaluation model,and then the scores of green degree in microwave-assisted leaching process was obtained.The greenness evaluation model was applied to the life cycle assessment of the microwave-assisted leaching process.The results show that the microwave-assisted leaching process has advantages over the conventional ones,with respect to energy-consumption,processing time and environmental protection.

Life cycle environmental impact assessment of biochar-based bioenergy production and utilization in Northwestern Ontario,Canada

Biochar-based bioenergy production and sub- sequent land application of biochar can reduce greenhouse gas emissions by fixing atmospheric carbon into the soil for a long period of time. A thorough life cycle assessment of biochar-based bioenergy production and biochar land application in Northwestern Ontario is conducted using SimaPro Ver. 8.1. The results of energy consumption and potential environmental impact of biochar-based bioenergy production system are compared with those of conventional coal-based system. Results show that biocbar land application consumes 4847.61 MJ per tonne dry feedstock more energy than conventional system, but reduces the GHG emissions by 68.19 kg CO2e per tonne of dry feed- stock in its life cycle. Biochar land application improves ecosystem quality by 18 %, reduces climate change by 15 %, and resource use by 13 % but may adversely impact on human health by increasing disability adjusted life years by 1.7 % if biomass availability is low to medium. Replacing fossil fuel with woody biomass has a positiveimpact on the environment, as one tonne of dry biomass feedstock when converted to biochar reduces up to 38 kg CO2e with biochar land application despite using more energy. These results will help understand a comprehensive picture of the new interventions in forestry businesses, which are promoting biochar-based bioenergy production.

Sustainable manufacturing,life cycle thinking and the circular economy

Achieving sustainable patterns of consumption and production is perhaps the biggest challenge facing our society today. The de-mand for more safe environmentally benign products is rising and many companies are looking for new ways to progressively improve the sus-tainability of their products. Moreover, there are numerous opportunities and countless innovations, technological as well as non-technologi-cal,that need to be exploited to improve the sustainability of products. Manufacturing industry is an important sector of any economy and hasthe potential to become a driving force for enabling sustainable patterns of production and consumption through introducing efficient productionpractices and developing products and services that help reduce environmental impacts. The benefits of adopting an integrated policy towardsproduct development based on life cycle thinking and eco-design to stimulate improvement of the environmental performance of each part ofproduct life cycle phases and achieve sustainable patterns of production and consumption are emphasized. The challenges in implementingsustainable manufacturing and the circular economy approaches are listed. A number of solutions are suggested to face up these challenges,for instance, increased awareness of enterprises particularly SME's of product life cycle issues and the opportunities that are available for costsavings and profit making from eco-innovation in product development for both the domestic and export markets and providing practical helpand advice directly to enterprises on integrated product development to promote enterprise led Eco-innovation. Aiming at contributing to sus-tainable manufacturing in China, Sino-UK Low Carbon Manufacturing Consortium, a multi-disciplinary research and educational partnershipbetween academia, industry and government agencies in the UK and China with interest in sustainable manufacturing issues, has been formedrecently.The vision, aims and benefits of membership of the consortium are also discussed.

Techno-Economic Analysis and Life Cycle Assessment for the Typical Intermediate Crude Refining Scheme in China

The integration of refinery and petrochemical units(IRPUs)has become an inevitable choice for the sustainable development of petrochemical industry.The utilization efficiency of petroleum resources could be improved obviously through IRPUs.However,integrating economic and environmental impacts into the model of IRPUs is still a grand challenge.Herein,a model called TEA-GHG-OPWM(Techno-Economic Analysis and GreenHouse Gases Oriented Plant-Wide Model)has been established on Aspen HYSYSTM platform to calculate the energy consumption,the technoeconomic performance,and the GHG emissions for two different kinds of schemes,viz,:VRHCU(Vacuum Residue Hydrocracking Unit)and VRDS-RFCC(Vacuum Residue Desulfurization and Residue Fluid Catalytic Cracking).Furthermore,a novel processing pathway named VGOHDT-HTMP-DC(Vacuum Gas Oil Hydrotreating,Hydrogenation and TMP coupling process and Delayed Coking)has also been developed to find methods to improve the economic performance based on a ten-million-CNY output value(TMYOV)and a reduced GHG emissions.Our results demonstrate that VRHCRU could consume more energy and emit more GHG(877.11 t of CO2 eq·TMYOV^-1·h^-1)than VRDS-RFCC(817.03 t of CO2 eq·TMYOV^-1·h^-1)and VGOHDT-HTMP-DC(721.96 t of CO2 eq·TMYOV^-1·h^-1),while obtaining a higher mass yield of petrochemicals.The VGOHDT-HTMP-DC process exhibits the lowest feedstock consumption,hydrogen consumption,energy consumption,and GHG emissions,indicating that VGOHDT-HTMP-DC has both well economic and environmentally friendly performance.

Life cycle assessment of HFC-134a production by calcium carbide acetylene route in China

HFC-134a is a widely used environment-friendly refrigerant.At present,China is the largest producer of HFC-134a in the world.The production of HFC-134a in China mainly adopts the calcium carbide acetylene route.However,the production route has high resource and energy consumption and large waste emission,and few of the studies addressed on the environmental performance of its production process.This study quantified the environmental performance of HFC-134a production by calcium carbide route via carrying out a life cycle assessment(LCA)using the CML 2001 method.And uncertainty analysis by Monte-Carlo simulation was also carried out.The results showed that electricity had the most impact on the environment,followed by steam,hydrogen fluoride and chlorine,and the impact of direct CO_(2) emissions in calcium carbide production stage on the global warming effect also could not be ignored.Therefore,the clean energy(e.g.,wind,solar,biomass,and natural gas)was used to replace coal-based electricity and coal-fired steam in this study,showing considerable environmental benefits.At the same time,the use of advanced production technologies could also improve environmental benefits,and the environmental impact of the global warming category could be reduced by 4.1%via using CO_(2) capture and purification technology.The Chinese database of HFC-134a production established in this study provides convenience for the relevant study of scholars.For the production of HFC-134a,this study helps to better identify the specific environmental hotspots and proposes useful ways to improve the environmental benefits.

Environmental load of solid wood floor production from larch grown at different planting densities based on a life cycle assessment

As one of the main structural units in a building,a solid wood floor has significant strategic research value for low-carbon energy saving.Taking the production line of a solid larch wood floor as a case study,we assessed the environmental load during production based upon a life cycle assessment.Using GaBi 6.0 software,we analyzed the associated carbon sequestration during floor production,with the initial planting density serving as the disturbance factor in a modular analysis.The results indicated that the cutting and finishing steps have relatively intense,negative influences on the environment,whereas transportation,ripping,and trimming do not.Additionally,recycling biomass waste has the potential to reduce greenhouse gas emissions.When the initial planting density was 3.0×3.0 m,carbon sequestration was relatively high.Although the emissions of freshwater pollutants,volatile organic compounds,and fine particulate matter（matter with a 2.5-μm diameter） were comparatively high,the reduction of greenhouse gas emissions was still excellent at this planting density.

Life cycle assessment of mobile phone housing

The life cycle assessment of the mobile phone housing in Motorola(China) Electronics Ltd. was carried out, in which materials flows and environmental emissions based on a basic production scheme were analyzed and assessed. In the manufacturing stage, such primary processes as polycarbonate molding and surface painting are included, whereas different surface finishing technologies like normal painting, electroplate, IMD and VDM etc. were assessed. The results showed that housing decoration plays a significant role within the housing life cycle. The most significant environmental impact from housing production is the photochemical ozone formation potential. Environmental impacts of different decoration techniques varied widely, for example, the electroplating technique is more environmentally friendly than VDM. VDM consumes much more energy and raw material. In addition, the results of two alternative scenarios of dematerialization showed that material flow analysis and assessment is very important and valuable in selecting an environmentally friendly process.

Life Cycle Assessment of Recycling High-Density Polyethylene Plastic Waste

Increasing production and use of various novel plastics products,a low recycling rate,and lack of effective recycling/disposal methods have resulted in an exponential growth in plastic waste accumulation in landfills and in the environment.To better understand the effects of plastic waste,Life Cycle Analysis(LCA)was done to compare the effects of various production and disposal methods.LCA shows the specific effects of the cradle-to-grave or cradle-to-cradle scenarios for landfill,incineration,and mechanical recycling.The analysis clearly indicates that increasing recycling of plastics can significantly save energy and eliminate harmful emissions of various carcinogens and GHGs into the environment.As recycling increases,the need for virgin-plastic production can be greatly reduced.Furthermore,the results of this study may help improve current mechanical recycling processes as well as potential future recycling methods,such as chemical recycling.Concerns about the current recycling/disposal methods for plastics have brought increasing attention to the waste accumulation problem.However,with the current COVID-19 pandemic,plastic accumulation is expected to increase significantly in the near future.A better understanding of the quantitative effects of the various disposal methods can help guide policies and future research toward effective solutions of the plastic waste problem.

Research on life cycle assessment of film-laminated steel packaging

The environmental issues associated with packaging materials have been attracting increasing attention.Life cycle assessment( LCA) is currently the main method used worldwide for evaluating green packaging materials. In this study,the LCA method was used to evaluate the environmental impact of Baosteel’s newly developed process for manufacturing film-laminated steel packaging materials,from raw material mining,production,and processing to their storage,consumption,recycling,and final disposal. The environmental performance and main influencing factors were analyzed and compared. In addition,the life cycle environmental characteristics of film-laminated steel cans,tin-plated steel cans,and aluminum cans were compared. Of the main environmental indicators of the life cycle of the film-laminated steel can,the environmental load of the substrate accounts for the largest proportion,follow ed by electricity. The environmental impact of the production of film materials cannot be ignored. The overall environmental performance of film-laminated steel cans is better than that of aluminum cans.

Stochastic Modelling of Vulnerability Life Cycle and Security Risk Evaluation

The objective of the present study is to propose a risk evaluation statistical model for a given vulnerability by examining the Vulnerability Life Cycle and the CVSS score. Having a better understanding of the behavior of vulnerability with respect to time will give us a great advantage. Such understanding will help us to avoid exploitations and introduce patches for a particular vulnerability before the attacker takes the advantage. Utilizing the proposed model one can identify the risk factor of a specific vulnerability being exploited as a function of time. Measuring of the risk factor of a given vulnerability will also help to improve the security level of software and to make appropriate decisions to patch the vulnerability before an exploitation takes place.