Life-Cycle Impact Assessment of Air Emissions from a Cement Production Plant in Cambodia

Cement industrial emissions account for 32% of air pollution in Cambodia. With that in mind, we examined the environmental impact of Cambodia’s cement industry and identified ways that it could reduce air pollution. The study focused on raw material extraction and preparation, calcination, and cement preparation. Data for the life-cycle inventory were provided by the Kampot Cement Plant. Air emissions were assessed using EMEP/EEA and IPCC criteria, and the impact assessment used ReCiPe (2016). The baseline analysis revealed that calcination contributed the most air pollutants, so mitigation scenarios focused on alternative fuels only during the calcination stage of cement production: 1) 100% coal (S1);2) 93% coal and 7% biomass (S2);3) 85% coal and 15% biomass (S3);4) 70% coal and 30% biomass (S4);and 5) 50% coal and 50% biomass (S5). The results demonstrated that certain mitigation measures reduced major emissions and environmental damage. S5 had the best results, reducing CO2 by 49.97, NOx by 2.233, and SO2 by 49.333%;however, it increased PM2.5 by 19.60% and total heavy metal (Pb, Cd, Hg, As, Cr, Cu, Ni, Se, Zn) output by 28.113%. The results of the study showed reductions in serious health and environmental effects associated with climate change of 48.83%, ozone generation of 9.62%, and particulate matter formation of 28.80%. However, carcinogenic and non-carcinogenic human toxicity increased by 35.66%. Therefore, such mitigation effect would be benefit to carbon reduction target in Cambodia.

Introducing a multi-criteria indicator to better evaluate impacts of rare earth materials production and consumption in life cycle assessment

Life cycle assessment （LCA） is based on the basic principles of sustainable development. LCA method demonstrated its efficiency in providing a systematic environmental assessment approach of a product or a process. The effectiveness and efficiency of these methods lies in the fact that they take into account all life cycle stages of a product, from the extraction of raw materials to end of life treatment （recycling, ...） through an assessment covering different impact categories such as climate change, human health, ecosystems and resources. Existing LCA indicators reflect different issues surrounding resource depletion, creating inconsistency and moreover confusion among LCA practitioners. The evaluation of different life cycle impacts assessment （LCIA） methods done by EC JRC showed that available models did not address the same parameters： short- vs long-term, stock vs backup technology, etc. It also showed that if the correlation between the methods was sufficient for some resources, others such as rare earth elements showed a high level of inconsistency between methods. It was therefore necessary to develop a relevant indicator and harmonized assessment of impacts on resources in LCA. Furthermore, a resource strategy indicator based on the three pillars of sustainable development （eco- nomic, environmental and social） would better address wider challenges and making it a more powerful decision making tool. This study aimed to introduce an indicator for evaluating the strategy implications of metal resources for products and to compare different ways of production resulting from extraction of raw materials or recycling, with a special focus on rare earth materials. The indicator would assess the impacts based on a reserve-resource vision [BGS NERC] and the evolution over time and founded over three pa- rameters： technical feasibility, economic viability and political stability （including social and environmental aspects） in representing countries.

Evaluation of Environmental Impacts of Traction Motor Production and Disposal

By the application of life cycle assessment(LCA) methodology, this paper estimates the environmental impacts of production and disposal of traction motors used in electric vehicles in China. The results show that the total energy use, the criteria emissions and the greenhouse gases(GHG) emissions of a traction motor production and disposal are about 2,899,MJ, 4.5,kg and 259.5,kg per motor, respectively. Among the regulated emissions, the SOxemission ranks first by total mass, followed by CO, PM10, NOx, PM2.5, and volatile organic compound(VOC). The motor material production stage accounts for most of the energy consumption and emissions, followed by the assembly stage and the end-of-life disposal stage. In this study, the environmental performance analysis is extended to the comparison between the use of secondary material and primary material for the material production stage. It is found that using 100% secondary material results in a 52.9% reduction in energy consumption, a 49.8% reduction in regulated emissions, and a 49.3% reduction in GHG emissions compared with the use of 100% primary material.

Life cycle assessment of low impact development technologies combined with conventional centralized water systems for the City of Atlanta, Georgia

Low-impact development （LID） technologies, such as bioretention areas, rooftop rainwater harvesting, a_nd xeris_caping can co_ntrol stormwater runoff, supply non-potable water, and landscape open space.TillS study examines a hybrid system （HS） that combines LID technologies with a centralized water system to lessen the burden on a conventional system （CS）. CS is defined as the stormwater collection and water supply infrastructure, and the conventional landscaping choices in the City of Atlanta. The study scope is limited to five single-family residential zones （SFZs）, classified R-1 through R-5, and four multi-family residential zones （MFZs）, classified RG-2 through RG-5. Population density increases from 0.4 （R-1） to 62.2 （RG-5） persons per 1,000 m2. We performed a life cycle assessment （LCA） comparison of CS and HS using TRACI 2.1 to simulate impacts on the ecosystem, human health, and natural resources. We quantified the impact of freshwater consumption using the freshwater ecosystem impact （FEI） indicator. Test results indicate that HS has a higher LCA single score than CS in zones with a low population density; however, the difference becomes negligible as population density increases. Incorporating LID in SFZs and MFZs can reduce potable water use by an average of 50%. and 25%,respectively.; however, water savings are negligible in zones with high population density （i.e., RG-5） due to the diminished surface area per capitaavailable for LID technoogies. The results demonstrate that LID technologies effectively reduce outdoor water demand and therefore would be a good choice to decrease the water consumption impact in the City of Atlanta.

Environmental impact assessment of emissions from non-recycled plastic-to-energy processes

Generally,plastics pose a variety of environmental impacts due to their increased use and non-biodegradability.End-of-life treatment is a viable way of recovering energy from plastics while at the same time reducing the amount of plastics disposed of in landfills.This paper studies the environmental impact of Non-Recycled Plastics(NRP)-to-energy processes.Three waste treatment processes were considered for NRP:pyrolysis,waste-to-energy(WtE),and landfill.The environmental impact assessment results indicated that conversion technologies such as pyrolysis and WtE are preferred over landfill.The total energy consumed in the pyrolysis process was 24635.7 MJ/tonne.The conversion technologies have a lower environmental impact and produced net positive energy from NRP.The global warming potential shows that pyrolysis(3.91 kg eq.CO_(2))contributes the least to global warming than waste-to-energy(18.56 kg eq.CO_(2))and landfill(17.5 kg eq.CO_(2)).However,sensitivity analysis suggested that the inefficiencies of the current conversion technologies should be addressed.Between the two technologies studied,pyrolysis contributed less environmental burden,having a lower global warming potential,a higher efficiency in energy conversion,and less harmful emissions such as selenium and methane.

Environmental impacts of a large-scale incinerator with mixed MSW of high water content from a LCA perspective

Large-scale incinerators are applied widely as a result of the heavy burden of municipal solid waste（MSW） generated, while strong opposition is arising from the public living nearby. A large-scale working incineration plant of 1500 ton/day was chosen for evaluation using life cycle assessment. It was found that the corresponding human toxicity impacts via soil（HTs）, human toxicity impacts via water（HTw） and human toxicity impacts via air（HTa）categories are 0.213, 2.171, and 0.012 personal equivalents（PE）, and global warming（GW100）and nutrient enrichment（NE） impacts are 0.002 and 0.001 PE per ton of waste burned for this plant. Heavy metals in flue gas, such as Hg and Pb, are the two dominant contributors to the toxicity impact categories, and energy recovery could reduce the GW100 and NE greatly. The corresponding HTs, HTw and HTa decrease to 0.087, 0.911 and 0.008 PE, and GW100 turns into savings of- 0.007 PE due to the increase of the heating value from 3935 to5811 k J/kg, if a trommel screener of 40 mm mesh size is used to pre-separate MSW. MSW sorting and the reduction of water content by physical pressure might be two promising pre-treatment methods to improve the combustion performance, and the application of stricter standards for leachate discharge and the flue gas purification process are two critical factors for improvement of the environmental profile identified in this work.

Information for Authors

The availability of resources for economic activities differs between regions, and the importance of the resources is consequently observed to be different within regions compared to a global scale. With the current situation in Chinese mining industry and its statistic characteristics, the characterization procedures of abiotic resource in life cycle impact assessment (LCIA) have demonstrated certain limita-tions in the Chinese materials industry. The aim of this paper is to propose new characterization and normalization factors for abiotic resource depletion categories such as metals and non-renewable en- ergy resources in a Chinese context. The actual production of abiotic resources calculated by a modi- fied model is compared to the reserve base in line with the new national standard to determine char- acterization factors in equivalence units, with antimony as the reference mineral. The normalization factors are based on the total base reserves of the most important minerals in China. A case study on primary magnesium production using the Pidgeon process is used to compare LCIA results for abiotic resource categories that are between current LCIA factors and the new Chinese factors. These factors not only reflect the importance of abiotic resource with respect to region-specific resource depletion, but also can compare with the global factors.