Study of the Lift Force Induced by An Interceptor on A High-Speed Mono-Hull:The Affecting Factors and Estimation Formula

To find a better way to estimate the lift force induced by an interceptor on a high-speed mono-hull ship,a series of high-speed mono-hull ship models are designed and investigated under different conditions.Different lift forces are obtained by numerical calculations and validated by a model test in a towing tank.The factors that influence the force are the interceptor height,velocity,draft,and deadrise angle.The relationship between each factor and the induced lift force is investigated and obtained.We found that the induced lift mainly depends on the interceptor height and advancing velocity,and is proportional to the square of the interceptor height and velocity.The results also showed that the effects of the draft and deadrise angle are relatively less important,and the relationship between the induced lift and these two factors is generally linear.Based on the results,a formula including the combined effect of all factors used to estimate the lift force induced by the interceptor is developed based on systematic analysis.The proposed formula could be used to estimate the lift force induced by interceptors,especially under high-speed condition.

A comparative study on kinetics and dynamics of two dump truck lifting mechanisms using MATLAB simscape

In this paper,two lifting mechanism models with opposing placements,which use the same hydraulic hoist model and have the same angle of 50°,have been developed.The mechanical and hydraulic simulation models are established using MATLAB Simscape to analyze their kinetics and dynamics in the lifting and holding stages.The simulation findings are compared to the analytical calculation results in the steady state,and both methods show good agreement.In the early lifting stage,Model 1 produces greater force and discharges goods in the container faster than Model 2.Meanwhile,Model 2 reaches a higher force and ejects goods from the container cleaner than its counterpart at the end lifting stage.The established simulation models can consider the effects of dynamic loads due to inertial moments and forces generated during the system operation.It is crucial in studying,designing,and optimizing the structure of hydraulic-mechanical systems.

Trajectory compensation for multi-robot coordinated lifting system considering elastic catenary of the rope

The multi-robot coordinated lifting system is an unconstrained system with a rigid and flexible coupling.The deformation of the flexible rope causes errors in the movement trajectory of the lifting system.Based on the kinematic and dynamic analysis of the lifting system,the elastic catenary mod-el considering the elasticity and mass of the flexible rope is established,and the effect of the deform-ation of the flexible rope on the position and posture of the suspended object is analyzed.According to the deformation of flexible rope,a real-time trajectory compensation method is proposed based on the compensation principle of position and posture.Under the lifting task of the low-speed move-ment,this is compared with that of the system which neglects the deformation of the flexible rope.The trajectoy of the lifting system considering the deformation of flexible rope.The results show that the mass and elasticity of the flexible rope can not be neglected.Meanwhile,the proposed trajectory compensation method can improve the movement accuracy of the lifting system,which verifies the ef-fectiveness of this compensation method.The research results provide the basis for trajectory plan-ning and coordinated control of the lifting system。

Epistemic-Based Investigation of the Probability of Hazard Scenarios Using Bayesian Network for the Lifting Operation of Floating Objects

Owing to the increase in unprecedented accidents with new root causes in almost all operational areas, the importance of risk management has dramatically risen. Risk assessment, one of the most significant aspects of risk management, has a substantial impact on the system-safety level of organizations, industries, and operations. If the causes of all kinds of failure and the interactions between them are considered, effective risk assessment can be highly accurate. A combination of traditional risk assessment approaches and modern scientific probability methods can help in realizing better quantitative risk assessment methods. Most researchers face the problem of minimal field data with respect to the probability and frequency of each failure. Because of this limitation in the availability of epistemic knowledge, it is important to conduct epistemic estimations by applying the Bayesian theory for identifying plausible outcomes. In this paper, we propose an algorithm and demonstrate its application in a case study for a light-weight lifting operation in the Persian Gulf of Iran. First, we identify potential accident scenarios and present them in an event tree format. Next, excluding human error, we use the event tree to roughly estimate the prior probability of other hazard-promoting factors using a minimal amount of field data. We then use the Success Likelihood Index Method(SLIM) to calculate the probability of human error. On the basis of the proposed event tree, we use the Bayesian network of the provided scenarios to compensate for the lack of data. Finally, we determine the resulting probability of each event based on its evidence in the epistemic estimation format by building on two Bayesian network types: the probability of hazard promotion factors and the Bayesian theory. The study results indicate that despite the lack of available information on the operation of floating objects, a satisfactory result can be achieved using epistemic data.

Abdominoplasty, Liposuction and Brazilian Butt Lift (BBL) in Kinshasa in the Democratic Republic of Congo. My Experience in This Aesthetic Plastic Surgery with Black African Women in a Low-Income Country

Background: In low-income African countries, the demand and use of plastic surgery operations including abdominoplasty, liposuction and Brazilian butt lift (BBL) are increasing. The goal of this work is to present my experience and the challenges of this aesthetic plastic surgery among black African women. Material and Methods: A retrospective study was conducted about the abdominoplasties, liposuctions and Brazilian butt lift (BBL) which I operated in public and private hospitals at Kinshasa (Democratic Republic of Congo) in black African women. It covers a period of 13 years, going from December 1, 2010 to December 1, 2023. For this study, I had at least 6 months period (to Juin 1, 2024) to assess the occurrence of early and late postoperative complications. Results: I performed 84 abdominoplasties, 144 liposuctions and 23 Brazilian butt lifts (BBL). The average age at the time of abdominoplasty was 44 years with extremes ranging from 26 to 55 years and a concentration of cases (60.7%) in the age group of 40 to 49 years. The age group of 20 to 29 years old represented the lowest rate of requests for abdominoplasty (4.7%). Patients with a BMI of 30 to 2 were the majority (61.9%), followed by those between 25 to 2 (29.7%). 67.8% of patients were obese (BMI ≥ 30 kg/m2). The average age at the time of liposuction was 41 years with extremes ranging from 21 years to 69 years;and more than half of cases (68%) in the age group between 30 and 49 years. As for Brazilian butt lift (BBL), the average age was 33 years with extremes ranging from 24 to 42 years and a concentration of patients (91.3%) between 20 and 39 years. The immediate postoperative complications of abdominoplasties observed were: seroma in 7% of cases, hematoma and partial infection of the surgical site in 5% of cases. Pathological scars (hypertrophic, keloid) after abdominoplasties were observed in 9% of cases. The most common complication of liposuction was contour deformity. I observed 16 patients (11.1%) with soft-tissue depressions or elevations, skin panniculus or folds. For Brazalian Butt Lift (BBL), complications like asymmetry for 2 patients (8.9%), contour irregularities for 2 patients (8.9%), and excessive fat removal for 6 patients (26%), had observed. I have not recorded any cases of death or pulmonary embolism. Conclusion: I perform aesthetic plastic surgery procedures in black African women with a high socioeconomic standard of living compared to the average of the general population. The renunciation of planned surgery is motivated by the impossibility of paying the cost of the operation as well as by popular and religious perceptions regarding cosmetic surgery. The results of these aesthetic plastic surgery procedures carried out are very satisfactory for them. The challenges to overcome are mainly threefold: the unforeseeable complications of these cosmetic plastic surgery procedures, popular and religious perceptions of cosmetic surgery as well as the poverty of the population.

Research on the Lifting Path of Data Literacy Ability of Applied University Teachers under the Perspective of Organizational Learning

With the arrival of the big data era, the modern higher education model has undergone radical changes, and higher requirements have been put forward for the data literacy of college teachers. The paper first analyzes the connotation of teacher data literacy, and then combs through the status quo and dilemmas of teachers’ data literacy ability in applied universities. The paper proposes to enhance the data literacy ability of teachers from the perspective of organizational learning. Through building a digital culture, building a data-driven teaching environment, and constructing an interdisciplinary learning community to further promote the application of the theory and practice of datafication inside and outside the organization, and ultimately improve the quality of teaching.

KINETIC MODELLING AND PERFORMANCE ANALYSIS OF THE FOUR-POST-FRAME LIFTING MECHANICAL SYSTEM

The kinetic model of the four-post-frame lifting mechanical system was established. The stiffness and damping matrices of differential equations of motion were obtained by using Lagrange’s equations. And the dynamic characteristics of system were analyzed by modal analysis method. Based upon this, the modifications of structural parameters which can improve dynamic performance were discussed. The low-level high-speed palletizer MDJ1200L was taken as a real case in the paper.

Construction analysis on integral lifting of steel structure by the vector form intrinsic finite element

A newnumerical method based on vector form intrinsic finite element（VFIFE） is proposed to simulate the integral lifting process of steel structures. First, in order to verify the validity of the VFIFE method, taking the steel gallery between the integrated building and the attached building of Nanjing M obile Communication Buildings for example, the static analysis was carried out and the corresponding results were compared with the results achieved by the traditional finite element method. Then, according to the characteristics of dynamic construction of steel structure integral lifting, the tension cable element was employed to simulate the behavior of dynamic construction. The VFIFE method avoids the iterative solution of the stiffness matrix and the singularity problems. Therefore, it is simple to simulate the complete process of steel structure lifting construction.Finally, by using the VFIFE, the displacement and internal force time history curves of the steel structures under different lifting speeds are obtained. The results show that the lifting speed has influence on the lifting force, the internal force, and the displacement of the structure. In the case of normal lifting speed, the dynamic magnification factor of 1. 5 is safe and reasonable for practical application.

Effect of Air Injector on the Performance of an Air-lift for Conveying River Sand

An air-lift has been more recently applied in the dredging, deep-seated beach placer mining and underground mining engineering. However, the influence and mechanism of various parameters on the air-lift performance are not quite clear, especially the influence of flow pattern on lifting efficiency. Focusing on the problems mentioned above, the key part of the air-lift （namely, the air injector） was proposed aimed to reduce friction loss in the inner pipe according to improving flow field performance, thus increase the lifting efficiency. The study of relative factors of the performance of an air-lift is performed and the river sand is used as simulation of underground ore bed. The total lifting height of the experimental system is 3 m, the water flux, mass flow of solid particles, concentration of particles and lifting efficiency are measured under the same submergence ratios by changing the air injector, which is divided into nine specifications of air injection in this research. The experimental results indicate that the optimal air flow rate corresponding to excellent performance of the air-lift can be obtained in the range of 35-40 m3/h. The air injection method has a great effect on the performance of the air-lift, the air injector with three nozzles is better than that in the case of one or two nozzles. Further more, the air injection angle and arrangement of air injection pipes also have great effect on the performance of an air-lift. The proposed research results have guiding significance for engineering application.

EFFECT OF INTERPHASE LIFT FORCE ON THE FLUID FLOW IN AN AIR-STIRRED CYLINDRICAL VESSEL

In the present paper, based on the two-phase model (Eulerian model), the two dimensional fluid flow liz air-stirred water systems is simulated, and the effect of interphase lift force on the fluid flow is specially discussed. In the Eulerian two-phase model, gas and liquid phase are considered to be two different continuous fluids interacting with each other through the finite inter-phase areas. The exchange between the phases is represented by source terms in conversation equations. Turbulence is assumed to be a property of the liquid phase, k - ε model is used to describe the behavior of the liquid phase. The dispersion of phases due to turbulence is represented by introducing a diffusion term in mass consecrvation equation. The contribution of bubble movement to the turbulent energy and its dissipation rate is taken into accounted by adding extra volumetric source terms to the equations of turbulent enemy and its dissipation rate. The comparison between the mathematical simulation and experiment data indicates that the interphase lift force has a big effect on the flow behavior, and considering both drug force and lift force as interphase forces is important to accurately simulate the gas-water two-phase fluid flow in air-stirred systems. The interphase lift force makes bubbles move away from the centerline, the gas concentration is decreased near the centerline, and increased near the wall. The lift force is smaller than drug force at the same place, especially far away from the centerline.

The Application of Surface Electromyography in the Assessment of Ergonomic Risk Factors Associated with Manual Lifting Tasks

Summary: The purpose of this study was to evaluate the ergonomic risk factors associated with manual lifting tasks using surface electromyography (EMG). 13 volunteers lifted loads of 6 and 13 kg at two speeds and at two horizontal distances in 3 different postures and three boxes of different sizes, from floor to knuckle height, performing 72 lifting tasks. For each lift, the surface electromyography signals from the erector spinae muscles, bilaterally at T_~10 and L_3, was recorded. The ergonomic risk factors associated with manual lifting tasks were evaluated by comparing the average amplitude of EMG signals from the erector spinae muscles. The EMG average amplitude for lifting the load of 13 kg was 14.3 % greater than that for lifting the load of 6 kg (t=-10.93, P<0.01). The EMG average amplitude at the site of L_3 was 10.3 % greater than that at the site of T_~10 (t=-7.98, P<0.01). The EMG average amplitude when performing “fast” lift was 5.9 %greater than the “slow” lift (t=-4.63, P<0.01). The posture of lifting affected the EMG average amplitude. It was lowest with semi-squat posture and greatest with squat posture (F=27.76, P<0.01). The result of multiple stepwise regression analysis showed that the loads of lifting, the size of box, horizontal distance, posture of lifting, the site of the spine subjected to force, lifting speed were the factors affecting the EMG average amplitude. The most significant factor was the loads of lifting, followed by the site of the spine subjected to force and the lifting speed in terms of risk. The ergonomic risk factors associated with manual lifting tasks includes the loads, posture, lifting speed, horizontal distance, the site of the spine subjected to force etc. The results of signal amplitude of EMG from the erector spinae muscles showed that semi-squat posture is the best posture for lifting tasks.

Influences of Lorentz force on the hydrofoil lift

In this paper, Lorentz forces are proved to be able to suppress separation in flows over hydrofoils. Furthermore, a differential equation of pressure distributions on the hydrofoil surface is derived, from which it is found that BVF （boundary vortex flux） σ is a suitable criterion for describing the lift coefficient variations during the electromagnetic control process. According to our numerical results, the periodic variations of lift for a hydrofoil at an attack angle of 17 ° are analyzed and its inherent mechanism is discussed in detail with the concept of BVE On the other hand, the effects of Lorentz force on the hydrofoil＇s lift are investigated both experimentally and numerically for different magnitudes and locations.

Magnetic resonance imaging findings for differential diagnosis of perianal plexiform schwannoma: Case report and review of the literature

Plexiform schwannoma is an extremely rare variant of schwannoma, accounting for approximately 5% of cases. Due to the rarity and lack of typical symptoms, signs and radiological images, a definite diagnosis of plexiform schwannoma may not be made by clinicians prior to biopsy. In the present study, we report the first case(to our knowledge) of perianal plexiform schwannoma arising from the overlapped skin of the ischioanal fossa, and we propose an intratumorally nonenhanced circumferential capsule dividing the tumour into multiple homogeneously enhanced nodules as a magnetic resonance imaging feature to aid in the differential diagnosis of plexiform schwannoma from ancient schwannoma, cavernous haemangioma, liposarcoma and plexiform neurofibroma.

Propeller Design for an Autonomous Underwater Vehicle by the Lifting-line Method based on OpenProp and CFD

A high-efficiency propeller can enable a long mission duration for autonomous underwater vehicles(AUVs).In this study,a new method with OpenProp coupled with computational fluid dynamics was developed to design a propeller for an Explorer100 AUV.The towed system simulation of the AUV was used to measure the nominal wake,and a self-propulsion simulation was used to measure the effective wake at the disc plane just in front of a propeller.Two propellers referring to the nominal wake(propeller 1)and effective wake(propeller 2)were designed with OpenProp and appended with the AUV for self-propulsion simulations,respectively.Through the numerical simulation of the AUV self-propulsion tests,the cruising velocity of AUV was obtained.The flow characteristics of the self-propulsion in pressure and velocity contours were also analyzed.The propeller designed with an effective wake improved the thrust,velocity,and efficiency by approximately 11.3%,6.7%,and 2.5%,respectively,as compared with those with a nominal wake.The cruising velocity of the final designed propeller for the Explorer100 AUV improved by 21.8%,as compared to that of the original propeller from the AUV free-running tests.

The Outlook of the Development of Innovative Products from Biocompatible Natural Spider Silk in the Beauty Thread-Lifting Industry

Embedding thread lift rhytidectomy,also known as“thread lifting”in China,with the natures of simple operation,less trauma and quick recovery,is progressively used in clinical practice as a new technology of face lifting.Herewith,a brief introduction of the previous advances of thread lifting techniques and materials in the facial beauty industry,combined with the discussion on various types of sutures,common complications,and the site of actions were provided.The main limitations of present thread lifting material include:(1)the use of non-absorbable sutures is liable to cause allergies and a series of complications;(2)the absorbable sutures are easily degradation,and people need to reshape in a relatively short period.Therefore,the high biocompatible spider silk was proposed as a novel material of thread lifting suture and related devices,the advantages and preliminary achievements on spider silk were also addressed.

Effect of the particle temperature on lift force of nanoparticle in a shear rarefied flow

The nanoparticles suspended in a shear flow are subjected to a shear lift force,which is of great importance for the nanoparticle transport.In previous theoretical analysis on the shear lift,it is usually assumed that the particle temperature is equal to the temperature of the surrounding gas media.However,in some particular applications,the particle temperature can significantly differ from the gas temperature.In the present study,the effect of particle temperature on the shear lift of nanoparticles is investigated and the corresponding formulas of shear lift force are derived based on the gas kinetic theory.For extremely small nanoparticles(with radius R<2 nm)or large nanoparticles(R>20 nm),the influence of the particle temperature can be neglected.For the intermediate particle size,the relative error induced by the equal gas–particle temperature can be significant.Our findings can bring an insight into accurate evaluation of the nanoparticle transport properties.

Second-generation wavelet finite element based on the lifting scheme for GPR simulation

Ground-penetrating radar(GPR)is a highly efficient,fast and non-destructive exploration method for shallow surfaces.High-precision numerical simulation method is employed to improve the interpretation precision of detection.Second-generation wavelet finite element is introduced into the forward modeling of the GPR.As the finite element basis function,the second-generation wavelet scaling function constructed by the scheme is characterized as having multiple scales and resolutions.The function can change the analytical scale arbitrarily according to actual needs.We can adopt a small analysis scale at a large gradient to improve the precision of analysis while adopting a large analytical scale at a small gradient to improve the efficiency of analysis.This approach is beneficial to capture the local mutation characteristics of the solution and improve the resolution without changing mesh subdivision to realize the efficient solution of the forward GPR problem.The algorithm is applied to the numerical simulation of line current radiation source and tunnel non-dense lining model with analytical solutions.Result show that the solution results of the secondgeneration wavelet finite element are in agreement with the analytical solutions and the conventional finite element solutions,thereby verifying the accuracy of the second-generation wavelet finite element algorithm.Furthermore,the second-generation wavelet finite element algorithm can change the analysis scale arbitrarily according to the actual problem without subdividing grids again.The adaptive algorithm is superior to traditional scheme in grid refinement and basis function order increase,which makes this algorithm suitable for solving complex GPR forward-modeling problems with large gradient and singularity.

AIRCRAFT LIFT AND MANEUVERABILITY ENHANCEMENT BY GENETIC GEOMETRY OPTIMIZATION OF LEX CONFIGURATION

To enhance the maneuverability of the selected aircraft model, a standard genetic algorithm （GA） is used as an optimization method for the preliminary design of the leading-edge extension （LEX） layout. The aerodynamic loads and the maximum lift coefficient of the complete aircraft configuration （fuselage＋wing＋tail） are computed by using the modified three-dimensional low-order panel method in conjunction with the semi-empirical formulas of DATCOM. Results show that the lift coefficient increases approximately 20.5%- 15.3% for Mach number 0. 4-0.8 and 6.8% for Mach number 1.2, and its maximum value approximately 9.5% -15.0% for Machnumber 0.2-0.95when LEXis installed. A 6.6%-8.0 % gain at altitudes of 1-5 km on the turn rate maneuverability and the corner speed have been achieved in the subsonic regime.

A Lifting Line Theory for a Three-dimensional Hydrofoil

Prandtl’s lifting line theory was generalized to the lifting problem of a three-dimensional hydrofoil in the presence of a free surface. Similar to the classical lifting theory, the singularity distribution method was utilized to solve two-dimensional lifting problems for the hydrofoil beneath the free surface at the air-water interface, and a lifting line theory was developed to correct three-dimensional effects of the hydrofoil with a large aspect ratio. Differing from the classical lifting theory, the main focus was on finding the three-dimensional Green function of the free surface induced by the steady motion of a system of horseshoe vortices under the free surface. Finally, numerical examples were given to show the relationship between the lift coefficient and submergence Froude numbers for 2-D and 3-D hydrofoils. If the submergence Froude number is small free surface effect will be significant registered as the increase of lift coefficient. The validity of these approaches was examined in comparison with the results calculated by other methods.

The Lifting Scheme Based on the Second Generation Wavelets

The lifting scheme is a custom design construclion of Biorthogonal wavelets, a fast and efficient method to realize wavelet transform,which provides a wider range of application and efficiently reduces the computing time with its particular frame. This paper aims at introducing the second generation wavelets, begins with traditional Mallat algorithms, illustrates the lifting scheme and brings out the detail steps in the construction of Biorthogonal wavelets. Because of isolating the degrees of freedom remaining the biorthogonality relations, we can fully control over the lifting operators to design the wavelet for a particular application, such as increasing the number of the vanishing moments.