Detection of Bearing Faults Using a Novel Adaptive Morphological Update Lifting Wavelet

The current morphological wavelet technologies utilize a fixed filter or a linear decomposition algorithm, which cannot cope with the sudden changes, such as impulses or edges in a signal effectively. This paper pre- sents a novel signal processing scheme, adaptive morpho- logical update lifting wavelet （AMULW）, for rolling element bearing fault detection. In contrast with the widely used morphological wavelet, the filters in AMULW are no longer fixed. Instead, the AMULW adaptively uses a morphological dilation-erosion filter or an average filter as the update lifting filter to modify the approximation signal. Moreover, the nonlinear morphological filter is utilized to substitute the traditional linear filter in AMULW. The effectiveness of the proposed AMULW is evaluated using a simulated vibration signal and experimental vibration sig- nals collected from a bearing test rig. Results show that the proposed method has a superior performance in extracting fault features of defective roiling element bearings.

Study on Dynamic Characteristics of Coupled Model for Deep-Water Lifting System

The underwater installation of marine equipment in deep-water development requires safe lifting and accurate positioning. The heave compensation system is an important technology to ensure normal operation and improve work accuracy. To provide a theoretical basis for the heave compensation system, in this paper, the continuous modeling method is employed to build up a coupled model of deep-water lifting systems in vertical direction. The response characteristics of dynamic movement are investigated. The simulation results show that the resonance problem appears in the process of the whole releasing load, the lifting system generates resonance and the displacement response of the lifting load is maximal when the sinking depth is about 2000 m. This paper also analyzes the main influencing factors on the dynamic response of load including cable stiffness, damping coefficient of the lifting system, mass and added mass of lifting load, among which cable stiffness and damping coefficient of the lifting system have the greatest influence on dynamic response of lifting load when installation load is determined. So the vertical dynamic movement response of the load is reduced by installing a damper on the lifting cable and selecting the appropriate cable stiffness.

THE CLINICAL ANALYSIS ON THERAPEUTIC EFFECT ON 47 CASES OF CERVICAL HEADACHE AND VERTIGO TREATED WITH ACUPUNCTURE,COMBINED WITH LIFTING,ROTATING,PULLING-MANIPULATION AT NECK

The cervical headache and vertigo were treated with acupuncture at Fengchi（GB20）and Wangu（GB 12）and lifting,rotating,pulling-manipulation at neck.The total effective ratewas 91.4％.The therapeutic effects of these two types,malposition type and osteophytosis type,were studied and compared.The results were significantly different in statistics.

Study on lift-up speed of aerodynamic compliant foil thrust bearings

Objective The experimental study on the lift-up speed of a new kind of compliant aerodynamic foil thrust bearings was performed on the multifunctional test rig established for testing the performances of foil gas bearings.Methods The lift-up speed of foil gas thrust bearing under given axial load was analyzed through the spectrum of axial displacement response in frequency domain.Results The test results indicated that the difference in the spectrum of axial displacement responses before and after lifting up of the rotor was obvious.After lifting up of the rotor,there were only larger components of rotation frequency and lower harmanic frequencies.If the rotor wasn't lift-up,there were also larger components of other frequencies in the spectrum.Conclusion So by analyzing the spectrum of axial displacement response,the results showed that the lift-up speed was about 1860rpm when the axial load was 31N.

Automatic lifting system design and application of large load powered support test rig

This paper presented a design of an automatic lifting system. It is used for large load powered support and improves the old method wherein powered support lifting depends on manual control. This system applies a high accuracy gear shunt motor to match the flow for 4 lifting cylinders, and also allocates bypass throttles to realize automatic lifting. Through the dis- placement sensor feedback the height deviation among 4 lifting cylinders during the whole lifting process, when the deviation is up to the sitting value, the corresponding bypass throttle is operated immediately to reduce the deviation, so that the moving platform of the powered support would not be stuck. Through real application, it is shown that this system can realize automatic lifting of powered support; the lifting speed is controlled between 5 and 10 mm/s, and the final aligning accuracy is up to 1 mm.

关联规则分析中兴趣度量Lift与Conviction的关系探讨及教育数据验证

关联规则分析是数据挖掘中最常用的研究方法之一。在关联关系的发现过程中兴趣度量是关联规则发现的理论基础,它可以度量规则的重要程度,其中Lift和Conviction这两个度量在数据分析中被广泛应用于筛选关联规则。本文对这两种兴趣度量进行了研究。首先,提出并证明了当后项集固定时,Conviction取值随Lift取值单调增加,且Conviction (Lift)是一个凸函数。然后,证明了当Confidence固定时,Conviction取值随Lift取值单调增加,且Conviction (Lift)是一个凹函数。最后,综合以上两个方面,得到一个重要结论:当后项集保持不变或当Confidence固定时,根据Conviction和Lift筛选出来的规则都是相同的。最后,利用某高校数学类专业三个年级的成绩数据进行了定理及相应结论的验证。

Study of the Lift Force Induced by An Interceptor on A High-Speed Mono-Hull:The Affecting Factors and Estimation Formula

To find a better way to estimate the lift force induced by an interceptor on a high-speed mono-hull ship,a series of high-speed mono-hull ship models are designed and investigated under different conditions.Different lift forces are obtained by numerical calculations and validated by a model test in a towing tank.The factors that influence the force are the interceptor height,velocity,draft,and deadrise angle.The relationship between each factor and the induced lift force is investigated and obtained.We found that the induced lift mainly depends on the interceptor height and advancing velocity,and is proportional to the square of the interceptor height and velocity.The results also showed that the effects of the draft and deadrise angle are relatively less important,and the relationship between the induced lift and these two factors is generally linear.Based on the results,a formula including the combined effect of all factors used to estimate the lift force induced by the interceptor is developed based on systematic analysis.The proposed formula could be used to estimate the lift force induced by interceptors,especially under high-speed condition.

A comparative study on kinetics and dynamics of two dump truck lifting mechanisms using MATLAB simscape

In this paper,two lifting mechanism models with opposing placements,which use the same hydraulic hoist model and have the same angle of 50°,have been developed.The mechanical and hydraulic simulation models are established using MATLAB Simscape to analyze their kinetics and dynamics in the lifting and holding stages.The simulation findings are compared to the analytical calculation results in the steady state,and both methods show good agreement.In the early lifting stage,Model 1 produces greater force and discharges goods in the container faster than Model 2.Meanwhile,Model 2 reaches a higher force and ejects goods from the container cleaner than its counterpart at the end lifting stage.The established simulation models can consider the effects of dynamic loads due to inertial moments and forces generated during the system operation.It is crucial in studying,designing,and optimizing the structure of hydraulic-mechanical systems.

CAE Supported Ornamental Flame Product Design-Vortex Flow Guiding with Fuel Lift Mechanism

The vortex flame design process was investigated. Combine qualitative and CAE （computer-aided engineering） simulation proposed to fulfill the functional requirement. Guidance channel can produce an ornamental flame with acceptable height. The lift mechanism comprises a supporting member and bearing and allows moving to the predetermined height. It allows a user to add fuel and cleaning base parts safely. Rigid body linkage and flow field simulated enables fine tune of geometric parameters. Functional test and measurement are carried out to confirm the product features. The measured average temperature of the metal chassis is 37.25℃, and that of glass is 141℃.

Lift up!要美臀,不要XI臀!

如果你在书桌前坐得很久，或坐在沙发上看电视时间久了，完美的身材比例将被破坏，臀部肌肉渐渐变成了那种肥硕而松弛的特形臀。想要塑造圆润迷人的美臀，记得每天做下面的臀部功课喔！仅需一两个星期就可改变你的“XL臀”！

Experimental and Numerical Investigation on the Aerodynamic Characteristics of High-Speed Pantographs with Supporting Beam Wind Deflectors

Aiming to mitigate the aerodynamic lift force imbalance between pantograph strips,which exacerbates wear and affects the current collection performance of the pantograph-catenary system,a study has been conducted to support the beam deflector optimization using a combination of experimental measurements and computational fluid dynamics(CFD)simulations.The results demonstrate that the size,position,and installation orientation of the wind deflectors significantly influence the amount of force compensation.They also indicate that the front strip deflectors should be installed downwards and the rear strip deflectors upwards,thereby forming a“π”shape.Moreover,the lift force compensation provided by the wind deflectors increases with the size of the deflector.Alternative wind compensation strategies,such as control circuits,are also discussed,putting emphasis on the pros and cons of various pantograph types and wind compensation approaches.

Analysis of Maximum Liquid Carrying Capacity Based on Conventional Tubing Plunger Gas Lift

China’s unconventional gas fields have a large number of low-productivity and low-efficiency wells, many of whichare located in remote and environmentally harsh mountainous areas. To address the long-term stable productionof these gas wells, plunger-lift technology plays an important role. In order to fully understand and accurately graspthe drainage and gas production mechanisms of plunger-lift, a mechanical model of plunger-liquid column uplift inthe plunger-lift process was established, focusing on conventional plunger-lift systems and representative wellboreconfigurations in the Linxing region. The operating casing pressure of the plunger-lift process and the calculationmethod for the maximum daily fluid production rate based on the work regime with the highest fluid recovery ratewere determined. For the first time, the critical flow rate method was proposed as a constraint for the maximumliquid-carrying capacity of the plunger-lift, and liquid-carrying capacity charts for conventional plunger-lift withdifferent casing sizes were developed. The results showed that for 23/8 casing plunger-lift, with a well depth ofshallower than 808 m, the maximum drainage rate was 33 m3/d;for 27/8 casing plunger-lift, with a well depth ofshallower than 742 m, the maximum drainage rate was 50.15 m3/d;for 31/2 casing plunger-lift, with a well depthof shallower than 560 m, the maximum drainage rate was 75.14 m3/d. This research provides a foundation for thescientific selection of plunger-lift technology and serves as a decision-making reference for developing reasonableplunger-lift work regimes.

Indirect Output Voltage Control in Negative Output Elementary Super Lift Luo Converter Using PIC plus FLC in Discontinuous Conduction Mode

In this paper, the design of a proportional integral controller (PIC) plus fuzzy logic controller (FLC) for the negative output elementary super lift Luo converter (NOESLLC) operated in discontinuous conduction mode (DCM) is presented. In spite of the many benefits viz. the high voltage transfer gain, the high efficiency, and the reduced inductor current and the capacitor voltage ripples, it natured with non-minimum phase. This characteristic makes the control of NOESLLC cumbersome. Any attempt of direct controlling the output voltage may erupt to instability. To overcome this problem, indirect regulation of the output voltage based on the two-loop controller is devised. The savvy in the inductor current control improves the dynamic response of the output voltage. The FLC is designed for the outer (voltage) loop while the inner (current) loop is controlled by the PIC. For the developed ?19.6 V NOESLLC, the dynamic performances for different perturbations (line, load and component variations) are obtained for PIC plus FLC and compared with PIC plus PIC. The study of two cases is performed at various operating regions by developing the MATLAB/Simulink model.

Trajectory compensation for multi-robot coordinated lifting system considering elastic catenary of the rope

The multi-robot coordinated lifting system is an unconstrained system with a rigid and flexible coupling.The deformation of the flexible rope causes errors in the movement trajectory of the lifting system.Based on the kinematic and dynamic analysis of the lifting system,the elastic catenary mod-el considering the elasticity and mass of the flexible rope is established,and the effect of the deform-ation of the flexible rope on the position and posture of the suspended object is analyzed.According to the deformation of flexible rope,a real-time trajectory compensation method is proposed based on the compensation principle of position and posture.Under the lifting task of the low-speed move-ment,this is compared with that of the system which neglects the deformation of the flexible rope.The trajectoy of the lifting system considering the deformation of flexible rope.The results show that the mass and elasticity of the flexible rope can not be neglected.Meanwhile,the proposed trajectory compensation method can improve the movement accuracy of the lifting system,which verifies the ef-fectiveness of this compensation method.The research results provide the basis for trajectory plan-ning and coordinated control of the lifting system。

改良LIFT手术联合自体富血小板PRP凝胶技术治疗肛瘘的临床研究

目的:探讨改良括约肌间瘘管结扎术(LIFT)手术联合自体富血小板PRP凝胶技术治疗肛瘘的临床疗效。方法:随机将2021年5月至2023年5月在我院接受治疗的62例肛瘘患者分为对照组和观察组,31例一组。对照组采用改良LIFT手术治疗,观察组予以改良LIFT手术联合自体富血小板PRP凝胶技术治疗。随访两个月,比较两组住院时间,创面愈合时间,创面瘢痕面积,临床疗效,术后疼痛评分,肛门功能评分,并发症发生率。结果:观察组的住院时间和创面愈合时间均短于对照组,创面瘢痕面积少于对照组(P<0.05)。观察组治疗有效率为96.77%,高于对照组的80.65%(P<0.05)。观察组术后1天、7天VAS评分及术后1、2个月Wexner评分均低于对照组(P<0.05)。观察组术后并发症发生为6.45%,低于对照组的25.81%(P<0.05)。结论:肛瘘采用改良LIFT手术联合自体富血小板PRP凝胶技术治疗效果突出,可以缓解术后疼痛,改善肛门功能,减少并发症,促进预后恢复,值得临床推广应用。

Coming up Roses An NPC deputy’s rose empire is helping lift farmers out of poverty in Sanya

The Chinese people are totally opposed to corruption. Establishing supervi sory commissions to perform duties in accordance with the Supervision Law will be the most effective way to fight corruption.

lift⁃off制程PEB温度对负性光阻显影后截面Profile的影响

本文研究了lift⁃off(揭开-剥离)制程曝光后烘烤温度(post exposure bake,PEB)对负性光阻显影截面Profile(光刻胶结构)的影响。结果表明:在保留原有PEB盘面加热的方式前提下通过增加PEB盘盖加热功能进行烘烤,通过控制PEB盘面温度可调整光阻关键尺寸(critical dimension,CD)及截面Profile形貌,通过控制PEB盘盖加热可调整截面Profile光阻顶端形貌及强度,可显著改善负性光阻显影后截面Profile难以调整的问题。另外,不同的盘面温度、不同盘盖温度以及不同的显影时间相互配合,可以实现一种负性光阻产生不同截面光刻胶结构效果,可以实现同种光阻lift⁃off制程多样化。

Abdominoplasty, Liposuction and Brazilian Butt Lift (BBL) in Kinshasa in the Democratic Republic of Congo. My Experience in This Aesthetic Plastic Surgery with Black African Women in a Low-Income Country

Background: In low-income African countries, the demand and use of plastic surgery operations including abdominoplasty, liposuction and Brazilian butt lift (BBL) are increasing. The goal of this work is to present my experience and the challenges of this aesthetic plastic surgery among black African women. Material and Methods: A retrospective study was conducted about the abdominoplasties, liposuctions and Brazilian butt lift (BBL) which I operated in public and private hospitals at Kinshasa (Democratic Republic of Congo) in black African women. It covers a period of 13 years, going from December 1, 2010 to December 1, 2023. For this study, I had at least 6 months period (to Juin 1, 2024) to assess the occurrence of early and late postoperative complications. Results: I performed 84 abdominoplasties, 144 liposuctions and 23 Brazilian butt lifts (BBL). The average age at the time of abdominoplasty was 44 years with extremes ranging from 26 to 55 years and a concentration of cases (60.7%) in the age group of 40 to 49 years. The age group of 20 to 29 years old represented the lowest rate of requests for abdominoplasty (4.7%). Patients with a BMI of 30 to 2 were the majority (61.9%), followed by those between 25 to 2 (29.7%). 67.8% of patients were obese (BMI ≥ 30 kg/m2). The average age at the time of liposuction was 41 years with extremes ranging from 21 years to 69 years;and more than half of cases (68%) in the age group between 30 and 49 years. As for Brazilian butt lift (BBL), the average age was 33 years with extremes ranging from 24 to 42 years and a concentration of patients (91.3%) between 20 and 39 years. The immediate postoperative complications of abdominoplasties observed were: seroma in 7% of cases, hematoma and partial infection of the surgical site in 5% of cases. Pathological scars (hypertrophic, keloid) after abdominoplasties were observed in 9% of cases. The most common complication of liposuction was contour deformity. I observed 16 patients (11.1%) with soft-tissue depressions or elevations, skin panniculus or folds. For Brazalian Butt Lift (BBL), complications like asymmetry for 2 patients (8.9%), contour irregularities for 2 patients (8.9%), and excessive fat removal for 6 patients (26%), had observed. I have not recorded any cases of death or pulmonary embolism. Conclusion: I perform aesthetic plastic surgery procedures in black African women with a high socioeconomic standard of living compared to the average of the general population. The renunciation of planned surgery is motivated by the impossibility of paying the cost of the operation as well as by popular and religious perceptions regarding cosmetic surgery. The results of these aesthetic plastic surgery procedures carried out are very satisfactory for them. The challenges to overcome are mainly threefold: the unforeseeable complications of these cosmetic plastic surgery procedures, popular and religious perceptions of cosmetic surgery as well as the poverty of the population.

消肿生肌汤辅助LIFT对高位单纯性肛瘘术后疼痛与康复进程的影响

目的:研究消肿生肌汤辅助经括约肌间瘘管结扎术(Ligation of intersphincteric fistula tract,LIFT)对高位单纯性肛瘘术后疼痛(Visual analogue scale,VAS)评分、康复进程的影响.方法:选取2020年8月至2022年8月于我院确诊的94例肛瘘患者作为研究对象,依随机对照法分为研究组和对照组,各47例.对照组采用LIFT术治疗,研究组在对照组基础上联合消肿生肌汤治疗.比较两组临床疗效、治疗后恢复情况及住院时间、治疗前后视觉模拟评分(VAS)、大便失禁严重性指数(Fecal incontinence severity index,FISI)、Wexner肛门失禁评分(Wexner)、肛肠动力学、相关血清指标水平.结果:研究组总有效率高于对照组(P<0.05);治疗后,研究组VAS、FISI、Wexner评分均低于对照组(P<0.05);研究组直肠静息压(Rectal resting pressure,RRP)、肛管最大收缩压(Analmaximal contraction pressure,AMCP)、肛管静息压(Anal tube resting pressure,ARP)、肛管最长收缩时间(Anal longest contraction,ALCT)水平高于对照组(P<0.05);研究组血清转化生长因子-β1(Transforming growth factor-β1,TGF-β1)、纤维连接蛋白(Fibronectin,FN)高于对照组,淀粉样蛋白A(Serum amyloid A,SAA)、趋化因子5(Chemokine ligand 5,CCL5)低于对照组(P>0.05);研究组恢复情况及住院时间短于对照组(P<0.05).结论:消肿生肌汤辅助LIFT对高位单纯性肛瘘患者术后效果显著,可有效促进患者创口愈合,减少炎症反应,降低肛肠疼痛度,缩短临床康复进程.

Research on the Lifting Path of Data Literacy Ability of Applied University Teachers under the Perspective of Organizational Learning

With the arrival of the big data era, the modern higher education model has undergone radical changes, and higher requirements have been put forward for the data literacy of college teachers. The paper first analyzes the connotation of teacher data literacy, and then combs through the status quo and dilemmas of teachers’ data literacy ability in applied universities. The paper proposes to enhance the data literacy ability of teachers from the perspective of organizational learning. Through building a digital culture, building a data-driven teaching environment, and constructing an interdisciplinary learning community to further promote the application of the theory and practice of datafication inside and outside the organization, and ultimately improve the quality of teaching.