Improving poor fill factors for solar cells via light-induced plating

Silicon solar cells are prepared following the conventional fabrication processes, except for the metal- lization firing process. The cells are divided into two groups with higher and lower fill factors, respectively. After light-induced plating （LIP）, the fill factors of the solar cells in both groups with different initial values reach the same level. Scanning electron microscope （SEM） images are taken under the bulk silver electrodes, which prove that the improvement for cells with a poor factor after LIP should benefit from sufficient exploitation of the high density silver crystals formed during the firing process. Moreover, the application of LIP to cells with poor electrode contact performance, such as nanowire cells and radial junction solar cells, is proposed.

Impaired pericyte-Müller glia interaction via PDGFRβ suppression aggravates photoreceptor loss in a rodent model of light-induced retinal injury

AIM:To investigate the involvement of pericyte-Müller glia interaction in retinal damage repair and assess the influence of suppressing the platelet-derived growth factor receptorβ(PDGFRβ)signaling pathway in retinal pericytes on photoreceptor loss and Müller glial response.METHODS:Sprague-Dawley rats were exposed to intense light to induce retinal injury.Neutralizing antibody against PDGFRβwere deployed to block the signaling pathway in retinal pericytes through intravitreal injection.Retinal histology and Müller glial reaction were assessed following light injury.In vitro,normal and PDGFRβ-blocked retinal pericytes were cocultured with Müller cell line(rMC-1)to examine morphological and protein expression changes upon supplementation with light-injured supernatants of homogenized retinas(SHRs).RESULTS:PDGFRβblockage 24h prior to intense light exposure resulted in a significant exacerbation of photoreceptor loss.The upregulation of GFAP and p-STAT3,observed after intense light exposure,was significantly inhibited in the PDGFRβblockage group.Fur ther upregulation of cytokines monocyte chemoattractant protein 1(MCP-1)and interleukin-1β(IL-1β)was also observed following PDGFRβinhibition.In the in vitro coculture system,the addition of light-injured SHRs induced pericyte deformation and upregulation of proliferating cell nuclear antigen(PCNA)expression,while Müller cells exhibited neuron-like morphology and expressed Nestin.However,PDGFRβblockage in retinal pericytes abolished these cellular responses to light-induced damage,consistent with the in vivo PDGFRβblockage findings.CONCLUSION:Pericyte-Müller glia interaction plays a potential role in the endogenous repair process of retinal injury.Impairment of this interaction exacerbates photoreceptor degeneration in light-induced retinal injury.

Light-Induced Changes in a-Si∶H Films Studied by Transient Photoconductivity

Light induced changes in a-Si∶H films are investigated by transient photoconductivity.The transient photoconductivity decay data can neither be fit well by common power-law for transient photocurrent in amorphous semiconductors,nor by stretched exponential rule for transient decay from the steady state in photoconductivity.Instead,the data are fit fairly well with a sum of two exponential functions.The results show that the long time decay is governed by deep traps rather than band tail states,and two different traps locating separately at 0.52 and 0.59eV below E _c are responsible for the two exponential functions.They are designated as negatively charged dangling bond D - centers.The light-induced changes in photoconductivity are attributed mainly to the decrease in electron lifetime caused by the increase of recombination centers after light soaking.

无界域上具有记忆的非自治Plate方程随机吸引子的存在性

研究无界域上一类具有衰退记忆和加性噪声的非自治Plate方程解的长时间行为.利用一致估计验证了解的拉回渐近紧性,获得了其随机吸引子的存在性.

Ti/(Ti,Cr)N/CrN multilayer coated 316L stainless steel by arc ion plating as bipolar plates for proton exchange membrane fuel cells

Arc ion plating (AIP) is applied to form Ti/(Ti,Cr)N/CrN multilayer coating on the surface of 316L stainless steel (SS316L) as bipolar plates for proton exchange membrane fuel cells (PEMFCs). The characterizations of the coating are analyzed by scanning electron microscopy (SEM) and X-ray diffraction (XRD). Interfacial contact resistance (ICR) between the coated sample and carbon paper is 4.9 m Omega cm(2) under 150 N/cm(2), which is much lower than that of the SS316L substrate. Potentiodynamic and potentiostatic tests are performed in the simulated PEMFC working conditions to investigate the corrosion behaviors of the coated sample. Superior anticorrosion performance is observed for the coated sample, whose corrosion current density is 0.12 mu A/cm(2). Surface morphology results after corrosion tests indicate that the substrate is well protected by the multilayer coating. Performances of the single cell with the multilayer coated SS316L bipolar plate are improved significantly compared with that of the cell with the uncoated SS316L bipolar plate, presenting a great potential for PEMFC application. (C) 2016 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. and Science Press. All rights reserved.

Light-Induced Reaction of Benzene with Carbonates

We found an ultraviolet （UV）-light induced formation of biphenyl and sodium benzoate from benzene and sodium carbonate. The reaction happens in the interface of benzene and aqueous solution at the room temperature. After 5 h of UV-light exposure, 11.4% of initial amount of 4.4 g （5.0 mL） benzene are converted to biphenyl and sodium benzoate, which are distributed in benzene and aqueous solution, respectively. Using density function theory （DFT） and time dependent DFT, we have investigated the mechanism of this light-induced reaction, and found that the sodium carbonate is not only a reactant for the formation of sodium benzoate, but also a catalyst for the formation of biphenyl.

Path planning for light-induced dielectrophoretic manipulation of micro-particles

To realize automatic manipulation of micro-particles by light-induced dielectrophoresis （LDEP）, a path-planning scheme based on the improved artificial potential field （APF） for micro light pattern movements is proposed. An algorithm combining guided target and point obstacle based on a new local minimum judging criterion is specially designed, which can solve the local minimum problems encountered by the traditional APF. Experiments of real-time particle manipulation based on this algorithm are implemented and the experimental results show that the proposed approach can overcome the local minimum problems of the traditional APF method, and it is validated to be highly stable for intensive particle obstacles during LDEP manipulation. Consequently, this method can realize real-time manipulation of micro-nano particles with safety, decrease the difficulty of manual manipulation, and thus improve the efficiency of manipulation of micro-particles.

Study on Misplating Problems of Composed of Wool and Lycra Plated Knitted Fabrics

By a great deal of experiments,the misplating problemsof plated knitted fabrics composed of wool and Lycra arediscussed and analyzed.The factors affecting the mis-plating problems on manually operated flat knitting ma-chine include the construction and adjustment of a plat-ing feeder,wool yarn count,feeding tension,takedowntension and the ground fabric structures.Some usefulresults can be derived from these works.

Dark Oscillation of Light-induced Absorption in Heavy Reduced Co: KNSBN Crystal

This paper presents dark oscillations of light-indhced absorption in heavy reduced Co: KNSBN crystal, points out there are double carriers and multiple traps in the crystal and explains the experimental results with the newly established model of double carriers and multiple traps.

Light-Induced Charge Transfer at Interface Between Lipid-Free RhTSPc Film and p-Si(111)

The present paper covers the lipid-free rhodium tetrasulfonato-phthalocyanine (RhTSPc) films prepared on p-Si(111) by using Langmuir-Blodgett technique. Their surface photovoltage spectra were measured. It was found that there is a strong interaction at the interface between the RhTSPc film and p-Si (111) and that the surface photovoltaic effect of the film system is maximum when only one monolayer of RhTSPc molecules coats p-Si(111), which is similar to that of CuTSPc films on p-Si(111) reported previously. These results confirm that only the monolayer of dye molecules being adjacent to the semiconductor surface plays a key role in the light-induced interfacial charge transfer process.

Oscillation of the spin-currents of cold atoms on a ring due to light-induced spin–orbit coupling

The evolution of two-component cold atoms on a ring with spin-orbit coupling has been studied analytically for the case with N noninteracting particles. Then, the effect of interaction is evaluated numerically via a two-body system. Two cases are considered： （i） Starting from a ground state the evolution is induced by a sudden change of the laser field, and （ii） the evolution starting from a superposition state. Oscillating persistent spin-currents have been found. A set of formulae have been derived to describe the period and amplitude of the oscillation. Based on these formulae the oscillation can be well controlled via adjusting the parameters of the laser beams. In particular, it is predicted that movable stripes might emerge on the ring.

A theory for three-dimensional response of micropolar plates

Through combined applications of the transfer-matrix method and asymptotic expansion technique,we formulate a theory to predict the three-dimensional response of micropolar plates.No ad hoc assumptions regarding through-thickness assumptions of the field variables are made,and the governing equations are two-dimensional,with the displacements and microrotations of the mid-plane as the unknowns.Once the deformation of the mid-plane is solved,a three-dimensional micropolar elastic field within the plate is generated,which is exact up to the second order except in the boundary region close to the plate edge.As an illustrative example,the bending of a clamped infinitely long plate caused by a uniformly distributed transverse force is analyzed and discussed in detail.

Advantage of Introducing Quantitative Light-Induced Fluorescence in School Dental Checkups

Background: Caries detection in school oral examinations insufficient accuracy. Objective: To evaluate advantages of introducing quantitative light-induced fluorescence-digital (QLF-D) in school oral examinations. Methods: Experiment No. 1. Early demineralized lesions in the upper and lower incisors and canines were visually inspected by three dentists and by QLF-D. The numbers of tooth planes with early demineralized lesions were compared between the methods. Experiment No. 2. Approximal demineralized lesions in molars were assessed by visual inspection, x-ray imaging, and QLF-D. The numbers of tooth planes with demineralized lesions were compared among the methods. Experiment No. 3. Plaque distribution was evaluated by QLF-D and a traditional staining method. The ratio of the diameter of plaque to tooth crown in the tooth axis direction in each method was calculated. The results were evaluated by Pearson’s correlation coefficient analysis and Bland-Altman plot. Results: Experiment No. 1. The three dentists found 0.67 tooth planes on average. QLF-D found 22 tooth planes with early demineralized lesions in the same samples. Experiment No. 2. Fourteen approximal tooth planes of molars were found to have demineralized lesions by x-ray imaging. QLF-D detected 71.4% of the tooth planes out of the 14, whereas visual inspection found 7.1%. Experiment No. 3. The Pearson’s correlation coefficient for the evaluations of plaque distribution between the QLF-D and traditional staining methods was 0.77 (P Conclusion: The results support introduction of QLF-D for use in school dental examinations.

Evaluating Acid Resistance Effect of Fluoride-Releasing Dental Materials Using Quantitative Light-Induced Fluorescence-Digital in Vitro

As erosion has become one of the serious oral health problems, some fluoride-releasing dental materials have been developed to protect enamel from demineralization. The purpose of this study was to evaluate the antidemineralization effect of PRG Barrier Coat® and FujiVII® (fluoride-releasing dental materials). Four square windows measuring 1 mm2 were prepared on the labial enamel surface of each bovine tooth using masking tape and nail varnish. The first and second windows were half covered by fluoride-releasing material and control material, respectively, whereas the third and fourth windows were left untreated. All windows were immersed into 0.1 M lactic acid and 6wt% CM-cellulose (pH 4.5) at 38℃ for 21 days. Subsequently, the first and second windows were covered with nail varnish after removal of the materials, and the third and fourth windows were immersed into ultrapure water at 38℃ for 28 days after being half covered with fluoride-releasing and control materials, respectively. The following procedure was performed separately during evaluations of the fluoride-releasing materials, PRG Barrier Coat, and FujiVII®, using eight and six bovine teeth, respectively. The first, second, third, and fourth windows were classified into DM-PRG;Demineralized-PRG or DM-FujiVII;Demineralized-FujiVII, DM-TCM;Demineralized-traditional cement or DM-TGIC;De-mineralized-traditional glass ionomer cement, RM-PRG;Remineralized-PRG or RM-FujiVII;Re-mineralized-FujiVII, and RM-TCM;Remineralized- traditional cement or RM-TGIC;Remineral-ized-traditional glass ionomer cement, respectively. After nail varnish was removed, △Q values (mean ± SD) of the windows were measured using QLF-D and were compared between DM-PRG and DM-TCM, RM-PRG and RM-TCM, DM-FujiVII and DM-TGIC, and RM-FujiVII and RM-TGIC groups. △Q values of RM-PRG (-60 ± 44) and RM-FujiVII (-5.0 ± 10) were significantly higher than that of RM-TCM (-315 ± 193) and RM-TGIC (-56 ± 43), respectively. The fluoride releasing materials provided remineralization effects to bovine enamel.

Light-Induced Mid-Infrared Emission of Liquid Carbon Tetrachloride and Benzene

Light-induced infrared emission spectroscopy (LIRES) is a novel technique that permits to receive high-quality spectra in the mid-infrared region. Low-intensity visible light connected to a highly sensitive FTIR spectrometer is more advantageous for studying any samples, including biological samples without any damage. This technique permits obtaining unique information on the molecule structure via vibrational excitation fundamental frequencies, overtones, and combination modes. It also enables a direct observation of vibrational radiation transitions in vibrationally excited molecules as well as the channels of vibration energy redistribution, which is not allowed with any other method. In this work, the LIRES is being tested as a technique for studying of vibrationally-excited molecules of carbon tetrachloride and benzene in the liquid phase. On the other hand, using transparent liquids, we had tried to understand some of the physical phenomena that can drive emission in mid-IR. The characteristics of the infrared emission of both liquid species produced by different wavelength radiation from various types of light systems (100 - watt Xe-lamp and Nd:YAG laser;lambda = 1064 nm (8 mW) and lambda = 532 nm (4 mW)) are presented. We demonstrated that the IR-signal, as well as spectral properties of carbon tetrachloride and benzene, was dependent on the wavelength and power of excitation beam. Results obtained with different light sources show that the visible light produces a nonlinear IR-emission signal in transparent liquids. We believe that the visible light is the source of the nonlinear response and is producing the vibration excitation as well as photostimulated transformations of the molecules possessing the high activity for the nonlinear response.

Improved YOLOv8n Model for Detecting Helmets and License Plates on Electric Bicycles

Wearing helmetswhile riding electric bicycles can significantly reduce head injuries resulting fromtraffic accidents.To effectively monitor compliance,the utilization of target detection algorithms through traffic cameras plays a vital role in identifying helmet usage by electric bicycle riders and recognizing license plates on electric bicycles.However,manual enforcement by traffic police is time-consuming and labor-intensive.Traditional methods face challenges in accurately identifying small targets such as helmets and license plates using deep learning techniques.This paper proposes an enhanced model for detecting helmets and license plates on electric bicycles,addressing these challenges.The proposedmodel improves uponYOLOv8n by deepening the network structure,incorporating weighted connections,and introducing lightweight convolutional modules.These modifications aim to enhance the precision of small target recognition while reducing the model’s parameters,making it suitable for deployment on low-performance devices in real traffic scenarios.Experimental results demonstrate that the model achieves an mAP@0.5 of 91.8%,showing an 11.5%improvement over the baselinemodel,with a 16.2%reduction in parameters.Additionally,themodel achieves a frames per second(FPS)rate of 58,meeting the accuracy and speed requirements for detection in actual traffic scenarios.

Lateral clavicle fracture-plating options and considerations

Clavicle fractures are among the most prevalent types of fractures with numerous treatment strategies that have evolved over time.In the realm of lateral-third clavicle fracture management,several surgical methods are available,with plate and screw constructs being one of the most frequently employed options.Within this construct,numerous choices exist for fixing the fracture.This editorial provides an overview of the common plate options utilized in the management of distal third clavicle fractures underscoring the critical considerations and approaches that guide clinicians in selecting the most appropriate fixation techniques,considering the complex landscape of clavicle fractures and their challenging management.

A Dynamic Coupling of Ocean and Plate Motion

Plate motion representing a remarkable Earth process is widely attributed to several primary forces such as ridge push and slab pull. Recently, we have presented that the ocean water pressure against the wall of continents may generate enormous force on continents. Continents are physically fixed on the top of the lithosphere that has been already broken into individual plates, this attachment enables the force to be laterally transferred to the lithospheric plates. In this study, we combine the force and the existing plate driving forces (i.e., ridge push, slab pull, collisional, and shearing) to account for plate motion. We show that the modelled movements for the South American, African, North American, Eurasian, Australian, Pacific plates are well agreement with the observed movements in both speed and azimuth, with a Root Mean Square Error (RMSE) of the modelled speed against the observed speed of 0.91, 3.76, 2.77, 2.31, 7.43, and 1.95 mm/yr, respectively.

Identification of the Caroline Plate boundary:constraints from magnetic anomaly

The Caroline Plate is located among the Pacific Plate,the Philippine Sea Plate,and the India Australia Plate,and plays a key role in controlling the spreading direction of the Philippine Sea Plate.The Caroline Submarine Plateau(or Caroline Ridge)and the Eauripik Rise on the south formed a remarkable T-shaped large igneous rock province,which covered the northern boundary between the Caroline Plate and the Pacific Plate.However,relationship between these tectonic units and magma evolution remains unclear.Based on magnetic data from the Earth Magnetic Anomaly Grid(2-arc-minute resolution)(V2),the normalized vertical derivative of the total horizontal derivative(NVDR-THDR)technique was used to study the boundary of the Caroline Plate.Results show that the northern boundary is a transform fault that runs 1400 km long in approximately 28 km wide along the N8°in E-W direction.The eastern boundary is an NNW-SSE trending fault zone and subduction zone with a width of tens to hundreds of kilometers;and the north of N4°is a fracture zone of dense faults.The southeastern boundary may be the Lyra Trough.The area between the southwestern part of the Caroline Plate and the Ayu Trough is occupied by a wide shear zone up to 100 km wide in nearly S-N trending in general.The Eauripik transform fault(ETF)in the center of the Caroline Plate and the fault zones in the east and west basins are mostly semi-parallel sinistral NNW-SSE–trending faults,which together with the eastern boundary Mussau Trench(MT)sinistral fault,the northern Caroline transform fault(CTF),and the southern shear zone of the western boundary,indicates the sinistral characteristics of the Caroline Plate.The Caroline hotspot erupted in the Pacific Plate near the CTF and formed the west Caroline Ridge,and then joined with the Caroline transform fault at the N8°.A large amount of magma erupted along the CTF,by which the east Caroline Ridge was formed.At the same time,a large amount of magma developed southward via the eastern branch of the ETF,forming the northern segment of the Eauripik Rise.Therefore,the magmatic activity of the T-shaped large igneous province is obviously related to the fault structure of the boundary faults between the Caroline Plate and Pacific Plate,and the active faults within the Caroline Plate.

Generative optimization of bistable plates with deep learning

Bistate plates have found extensive applications in the domains of smart structures and energy harvesting devices.Most bistable curved plates are characterized by a constant thickness profile.Regrettably,due to the inherent complexity of this problem,relatively little attention has been devoted to this area.In this study,we demonstrate how deep learning can facilitate the discovery of novel plate profiles that cater to multiple objectives,including maximizing stiffness,forward snapping force,and backward snapping force.Our proposed approach is distinguished by its efficiency in terms of low computational energy consumption and high effectiveness.It holds promise for future applications in the design and optimization of multistable structures with diverse objectives,addressing the requirements of various fields.