k_(eff)uncertainty quantification and analysis due to nuclear data during the full lifetime burnup calculation for a small-sized prismatic high temperature gas-cooled reactor

To benefit from recent advances in modeling and computational algorithms,as well as the availability of new covariance data,sensitivity and uncertainty analyses are needed to quantify the impact of uncertain sources on the design parameters of small prismatic high-temperature gascooled reactors(HTGRs).In particular,the contribution of nuclear data to the k_(eff)uncertainty is an important part of the uncertainty analysis of small-sized HTGR physical calculations.In this study,a small-sized HTGR designed by China Nuclear Power Engineering Co.,Ltd.was selected for k_(eff)uncertainty analysis during full lifetime burnup calculations.Models of the cold zero power(CZP)condition and full lifetime burnup process were constructed using the Reactor Monte Carlo Code RMC for neutron transport calculation,depletion calculation,and sensitivity and uncertainty analysis.For the sensitivity analysis,the Contribution-Linked eigenvalue sensitivity/Uncertainty estimation via Track length importance Characterization(CLUTCH)method was applied to obtain sensitive information,and the "sandwich" method was used to quantify the k_(eff)uncertainty.We also compared the k_(eff)uncertainties to other typical reactors.Our results show that ^(235)U is the largest contributor to k_(eff)uncertainty for both the CZP and depletion conditions,while the contribution of ^(239)Pu is not very significant because of the design of low discharge burnup.It is worth noting that the radioactive capture reaction of ^(28)Si significantly contributes to the k_(eff)uncertainty owing to its specific fuel design.However,the k_(eff)uncertainty during the full lifetime depletion process was relatively stable,only increasing by 1.12%owing to the low discharge burnup design of small-sized HTGRs.These numerical results are beneficial for neutronics design and core parameters optimization in further uncertainty propagation and quantification study for small-sized HTGR.

Study on Contra-Rotating Small-Sized Axial Flow Hydro Turbine

It is thought that small hydropower generation is alternative energy, and the energy potential of small hydropower is large. The efficiency of small hydro turbines is lower than that of large one, and these small hydro turbine’s common problems are out of operation by foreign materials. Then, there are demands for small hydro turbines to keep high per- formance and wide flow passage. Therefore, we adopted contra-rotating rotors which can be expected to achieve high performance and low-solidity rotors with wide flow passage in order to accomplish high performance and stable opera- tion. Final goal on this study is development of an electric appliance type small hydro turbine which has high portability and makes an effective use of the unused small hydro power energy source. In the present paper, the performance and the internal flow conditions in detail of contra-rotating small-sized axial flow hydro turbine are shown as a first step of the research with the numerical flow analysis. Then, a capability adopting contra-rotating rotors to an electric appliance type small hydro turbine was discussed. Furthermore, the high performance design for it was considered by the numeri- cal analysis results.

Effect of Organic and Chemical Fertilizer Application on Growth, Yield, and Quality of Small-Sized Tomatoes

Tomatoes in Japan are generally cultivated under management systems that use chemical fertilizers and synthetic chemical pesticides. However, the continuous use of these fertilizers and pesticides damages the soil environment and reduces the number of soil microorganisms. Organic farming has a relatively low environmental impact compared to conventional farming techniques, but typically has lower and more unstable yields. In this study, we investigated the effect of organic and chemical fertilizer application on growth, yield, and quality of small-sized (cherry) tomatoes. Cherry tomatoes were cultivated using organic and chemical organic fertilizers. Average weight and lateral diameter were significantly higher under organic fertilizer than under chemical fertilizer. In addition, shoot dry weight was significantly higher under organic fertilizer than chemical fertilizer. Lycopene content was significantly higher under organic fertilizer than chemical fertilizer. The total carbon (TC), total phosphorus (TP), total potassium (TK), available phosphoric (SP) and exchangeable potassium (SK) contents, C/N ratio, and pH were significantly higher under organic fertilizer than chemical fertilizer. Bacterial biomass, nitrite (NO? 2-N) oxidation activity, nitrification (N) circulation activity, and phosphoric (P) circulation were higher under organic fertilizer than chemical fertilizer. From these results, the study indicates that appropriate controls such as TC, total nitrogen (TN), and C/N ratio of organic fertilizer increased microbial biomass and enhanced nutrient circulation such as N circulation activity and P circulation activity. These results can be used to improve current organic farming practices and promote soil conservation.

Influence of Small-Size Contaminations on Thin Film Structural Properties

An approach for studying the influence of nano-particles on the structural properties of deposited thin films is proposed. It is based on the molecular dynamic modeling of the deposition process in the presence of contaminating nano-particles. The nano-particle is assumed to be immobile and its interaction with film atoms is described by a spherically symmetric potential. The approach is applied to the investigation of properties of silicon dioxide films. Visualization tools are used to investigate the porosity associated with nano-particles. The structure of the film near the nano-particle is studied using the radial distribution function. It is found that fluctuations of film density near the nano-particles are essentially different in the cases of low-energy and high-energy deposition processes.

Internal Flow Condition between Front and Rear Rotor of Contra-Rotating Small-Sized Axial Fan at Low Flow Rate

Contra-rotating small-sized fans are used as cooling fans for electric equipment. The internal flow condition between the front and rear rotors of the contra-rotating small-sized fan is not known well especially at the low flow rate. Furthermore, the blade row distance between the front and rear rotors is an important parameter for the contra-rotating small-sized fan and its influence on the internal flow condition is not clarified at the low flow rate. Therefore, the internal flow condition of the contra-rotating small-sized fan at the low flow rate is investigated by the numerical analysis in this research. The numerical analysis results are validated by comparing the fan static pressure curves of the numerical results to the experimental results. The internal flow condition at the low flow rate is clarified using the numerical models of the different blade row distance L = 10 mm and 30 mm. In the present paper, pressure fluctuations phase locked each front and rear rotor’s rotation are shown and the influences of the wake and the potential interference are discussed by the unsteady numerical analysis results at the low flow rate.

Performance and Internal Flow of Contra-Rotating Small-Sized Cooling Fan

High pressure and large flow rate small-sized cooling fans are used for servers in data centers and there is a strong demand to increase its performance because of increase of quantity of heat from servers. Contra-rotating rotors have been adopted for some of high pressure and large flow rate cooling fans to meet the demand. The performance curve of the contra-rotating small-sized cooling fan with 40 mm square casing was investigated by an experimental apparatus and its internal flow condition was clarified by the numerical analysis. The fan static pressure of the front rotor was extremely low and it increased significantly at the rear rotor. The uniform flow was achieved at the inlet of the rear rotor because of the special shape of the casing between the front and rear rotors. On the other hand, the tip leakage flow was large enough to influence on the main flow of the test cooling fan by the design specification of high pressure with compact rotor diameter.

Space-to-Ground Quantum Key Distribution Using a Small-Sized Payload on Tiangong-2 Space Lab

Quantum technology establishes a foundation for secure communication via quantum key distribution （QKD）. In the last two decades, the rapid development of QKD makes a global quantum communication network feasible. In order to construct this network, it is economical to consider small-sized and low-cost QKD payloads, which can be assembled on satellites with different sizes, such as space stations. Here we report an experimental demonstration of space-to-ground QKD using a small-sized payload, from Tiangong-2 space lab to Nanshan ground station. The 57.9-kg payload integrates a tracking system, a QKD transmitter along with modules for synchronization, and a laser communication transmitter. In the space lab, a 50MHz vacuum＋weak decoy-state optical source is sent through a reflective telescope with an aperture of 200mm. On the ground station, a telescope with an aperture of 1200mm collects the signal photons. A stable and high-transmittance communication channel is set up with a high-precision bidirectional tracking system, a polarization compensation module, and a synchronization system. When the quantum link is successfully established, we obtain a key rate over 100bps with a communication distance up to 719km. Together with our recent development of QKD in daylight, the present demonstration paves the way towards a practical satellite-constellation-based global quantum secure network with small-sized QKD payloads.

Peers Small-sized Group Work-A Beneficial Form of Classroom Interaction

Classroom interaction plays a critical role in language teaching and learning process.It involves both the teacher-students,and students-students.This article is intended to explore the vital significance of classroom interaction in language learning process with the emphasis placed on the students' involvement in the classroom activities,furthermore,to discover whether the peers small-sized group work is a beneficial and irreplaceable form of classroom interaction.

A low-melting-point metal doping strategy for the synthesis of small-sized intermetallic Pt5Ce fuel cell catalysts

Carbon-supported platinum-lanthanum(Pt-Ln)intermetallic compound(IMC)nanoparticles with high activity and robust stability have been demonstrated as promising cathode catalysts for proton-exchange membrane fuel cells.However,the preparation of Pt-Ln IMC catalysts needs high-temperature annealing treatment that inevitably causes nanoparticle sintering,resulting in significant reduction of the electrochemical surface area and mass-based activity.Here,we prepare small-sized M-doped Pt5Ce(M=Ga,Cd,and Sb)IMCs catalysts via a low-melting-point metal doping strategy.We speculate that the doping of low-melting-point metals can facilitate the generation of vacancies in the crystal lattice through thermal activation and thus reduce the kinetic barriers for the formation of intermetallic Pt5Ce catalysts.The prepared Ga-doped Pt5Ce catalyst exhibits a higher electrochemical active surface area(81 m^(2)·gPt^(-1))and a larger mass activity(0.45 A·mgPt^(-1)at 0.9 V)over the undoped Pt5Ce and commercial Pt/C catalysts.In the membrane electrode assembly test,the Ga-doped Pt5Ce cathode delivers a power density of 0.98 W·cm^(-2)at 0.67 V,along with a voltage loss of only 27 mV at 0.8 A·cm^(-2)at the end of accelerated stability test.

Progress in Light-weight High Entropy Alloys

High entropy alloys(HEAs)possess good mechanical properties and a wide range of industrial applications.In this paper,phase formation prediction theory,microstructure,properties and preparation methods of light-weight HEAs(LWHEAs)were reviewed.The problems and challenges faced by LWHEAs development were analyzed.The results showed that many aspects are still weak and require investigation for future advanced alloys,such as clarification of the role of entropy in phase formation and properties of HEAs,improved definition and different generations division of HEAs,close-packed hexagonal(HCP)phase structure prediction and corresponding alloy design and fabrication.Finally,some suggestions were presented in this paper including in-depth research on formation mechanism of multi-component alloy phase and strengthening of large-scale HEA preparation methods via technology compounding and 3D printing technology.Also,there is a need for more research on the in-situ preparation of HEA coatings and films,as well as developing LWHEAs with superior strength and elevated temperature resistance or ultra-low temperature resistance to meet the requirements of future engineering applications.

Preparation of Light-weight Spinel Refractories by Foaming-gel Process

Light-weight magnesium -aluminate spinel materi- als were prepared by foaming-gel process with polyalumi- nium chloride （PAC） as gel. Effect of solid loading in initial slurry on microstructure, porosity, pore size distri- bution, thermal conductivity and mechanical properties was investigated. The results show that the bulk density of the light-weight magnesium -aluminate spinel mate- rials is in the range of O. 7 1.2 g cm-3 ; pore size distribution curves show single-peak characteristics and the mean pore size is in the range of 30. 83 - 61.37 μm ; with the increase of solid loading, the linear shrinkage of the green body during firing and the permanent change in dimensions on heating at l 600 ℃ for 3 h de- crease, but the bulk density increases, the mechanical properties increase obviously; the maximum compressive strength and bending strength reach 35. 25 MPa and 9. 92 MPa, respectively, while the bulk density is 1. 16 g · cm ; and the thermal conductivity at 1 000 ℃ tea- ches 0. 371 W · m-1 . K-1 while the bulk density is O. 7 -3 g · cm

Investigation on microstructures and properties of semi-solid Al_(80)Mg_(5)Li_(5)Zn_(5)Cu_(5)light-weight high-entropy alloy during isothermal heat treatment process

The Al_(80)Mg_(5)Li_(5)Zn_(5)Cu_(5)light-weight high-entropy alloy with globular microstructure was fabricated by isothermal heat treatment.The effects of isothermal temperatures and holding times on the semi-solid microstructure evolution were investigated.The results indicate that,with increase of the isothermal temperature,the average grain size increases and the spheroidization time shortens.With prolongation of holding time,the shape factor increases firstly and then decreases,and the average grain size decreases at first and then increases when the isothermal temperature is below 520°C,however it increases gradually at 540℃.The optimal semi-solid microstructure is obtained at 520℃ for 30 min,whose shape factor and average grain size are 0.90 and 56.4μm,respectively.Compared with as-cast Al_(80)Mg_(5)Li_(5)Zn_(5)Cu_(5) light-weight high-entropy alloy,the compressive strength and plasticity of semi-solid Al_(80)Mg_(5)Li_(5)Zn_(5)Cu_(5) light-weight high-entropy alloy are increased by 36%and 108%,respectively.The formation of semi-solid microstructures includes three stages:melting separation,spheroidization,and coarsening growth.The sluggish diffusion effect of Al_(80)Mg_(5)Li_(5)Zn_(5)Cu_(5) light-weight high-entropy alloy leads to a low coarsening rate,resulting in slow grain growth.

Principles and Chief Technologies in Developing Light-weighted Worsted Fabrics

More and more light-weighted fabrics are being required by the market, especially for the worsted manufacture.In the past, such fabrics are produced mainly through changing the structure of woven goods or by using finer yarns. But these possibilities are very limited. In this paper, new devices are discussed: (1) on the yarn level- to use single yarns instead of conventional doubled ones, to decrease number of fibers in yarn cross sections beth during spinning and after finishing; (2) on the fiber level - to use finer fibers in blends with wool and modification of the wool fibers; (3) on the macromolecule level - to stretch the macromolecules in alpha keratin, to get super fine wool fibers.

Ultra-thin and light-weight spoof surface plasmon polariton coupler achieved by broadside coupled split ring resonators

Low profile and light weight are very important for practical applications of a spoof surface plasmon polariton（SSPP）coupler, especially at low frequencies. In this paper, we propose and design an ultra-thin, light-weight SSPP coupler based on broadside coupled split ring resonators（BC-SRRs）. The size of BC-SRR can be far less than λ/100 and can extremely well control the reflective phases within a subwavelength thickness. Due to the broadside capacitive coupling, the electrical size of BC-SRR is dramatically reduced to guarantee the ultra-thin thickness of the SSPP coupler. The weight of the SSPP coupler is reduced by a low occupation ratio of BC-SRR in the unit cell volume. As an example, a C-band SSPP coupler composed of phase gradient BC-SRRs is designed, fabricated, and measured. Due to the ultra-small size and low occupation ratio of BC-SRRs, the thickness of the coupler is λ/12 and the surface density is only 0.98 kg/m^2. Both simulation and experiment results verify that the coupler can achieve high-efficiency SPP coupling at 5.27 GHz under normal incidence.

Effect of Commercial Synthappret BAP Treatment on the Tailorability of Light-Weight Worsted Wool Fabrics

By means of measurement with the FAST instruments,the effect of commercial Synthappret BAP treatment on the tailorability of light-weight wool worsted fabrics has been investigated. It was found that the commercial Synthappret BAP treatment improved the tailorability of the light-weight wool fabrics mainly by increasing the bending stiffness of the light-weight wool fabrics.

Effects of Spherical Light-weight Aggregates Additions on Workability and Mechanical Properties of Al_2O_3-SiO_2 System Castables

In order to clarify the effect of spherical light-weight aggregates addition on properties of A12 07 - Si02 system castables, adopting ATO mullite traditional light-weight aggregates and ATO mullite spherical light-weight aggre- gates, bauxite homogenization powder, microsilica , cal- cium aluminate cement as main raw materials, light- weight Al2 03 - SiO2 system castables were prepared by replacing conventional light-weight aggregate with spherical light-weight aggregates. The effects of spheri- cal light-weight aggregates addition on workability, me- chanical properties of castables after heated at different temperatures were researched; the microstructure of the aggregates was analyzed by SEM. The result shows that the introduction of spherical light-weight aggregates can significantly improve the flowability and reduce the water addition of the castables. Water demand of the castable is reduced from 18% with the conventional light-weight aggregates to 14% with spherical light-weight aggre- gates. In addition, light-weight castables prepared by spherical aggregates can keep the same workability with- in a wider range of water addition. Therefore, spherical aggregates are user-friendly. The introduction of spheri- cal light-weight aggregates is favorable to packing densi- ty and mechanical properties of castables, such as cold crushing strength, cold modulus of rupture, hot modulus of rupture at 1 200℃.

A Study of Thermal Response and Flow Field Coupling Simulation around Hayabusa Capsule Loaded with Light-Weight Ablator

The numerical simulation of flow field around Hayabusa capsule loaded with light-weight ablator thermal response coupled with pyrolysis gas flow inside the ablator was carried out. In addition, the radiation from high temperature gas around the capsule was coupled with flow field. Hayabusa capsule reentered the atmosphere about 12 km/sec in velocity and Mach number about 30. During such an atmospheric entry, space vehicle is exposed to very savior aerodynamic heating due to convection and radiation. In this study, Hayabusa capsule was treated as a typical model of the atmospheric entry spacecraft. The light-weight ablator had porous structure, and permeability was an important parameter to analyze flow inside ablator. In this study, permeability was a variable parameter dependent on density of ablator. It is found that the effect of permeability of light-weight ablator was important with this analysis.

Small-sized tungsten nitride anchoring into a 3D CNT- rGO framework as a superior bifunctional catalyst for the methanol oxidation and oxygen reduction reactions

The application of direct methanol fuel cells （DMFC） is hampered by high cost, low activity, and poor CO tolerance by the Pt catalyst. Herein, we designed a fancy 3D hybrid by anchoring tungsten nitride （WN） nanoparticles （NPs）, of about 3 nm in size, into a 3D carbon nanotube-reduced graphene oxide framework （CNT-rGO） using an assembly route. After depositing Pt, the contacted and strongly coupled Pt-WN NPs were formed, resulting in electron transfer from Pt to WN. The 3D Pt-WN/CNT-rGO hybrid can be used as a bifunctional electrocatalyst for both methanol oxidation reaction （MOR） and oxygen reduction reaction （ORR）. In MOR, the catalysts showed excellent CO tolerance and a high mass activity of 702.4 mA.mgpt-1, 2.44 and 3.81 times higher than those of Pt/CNT-rGO and Pt/C（JM） catalysts, respectively. The catalyst also exhibited a more positive onset potential （1.03 V）, higher mass activity （151.3 mA.mgpt-1）, and better cyclic stability and tolerance in MOR than ORR. The catalyst mainly exhibited a 4e-transfer mechanism with a low peroxide yield. The high activity was closely related to hybrid structure. That is, the 3D framework provided a favorable path for mass-transfer, the CNT-rGO support was favorable for charge transfer, and strongly coupled Pt-WN can enhance the catalytic activity and CO-tolerance of Pt. Pt-WN/CNT-rGO represents a new 3D catalytic platform that is promising as an electrocatalyst for DMFC because it can catalyze both ORR and MOR in an acidic medium with good stability and highly efficient Pt utilization.

Characteristics and EOR mechanisms of nanofluids permeation flooding for tight oil

Tight oil reservoir development is faced with the key technical problem that"water cannot be injected and oil cannot be produced"yet.With the diphenyl ethers water-soluble(gemini)surfactants as water phase shell and C10–C14 straight-chain hydrocarbon compounds as oil phase kernel,a nanofluids permeation flooding system was prepared by microemulsion technology,and its characteristics and EOR mechanisms were evaluated through experiments.The system has the following five characteristics:(1)"Small-size liquid":the average particle size of the system is less than 30 nm,which can greatly reduce the starting pressure gradient of water injection,and effectively enter and expand the sweep volume of micro-nano matrix;(2)"Small-size oil":the system can break the crude oil into"small-size oil"under the flow condition,which can greatly improve the percolation ability and displacement efficiency of the crude oil in the micro-nano matrix;(3)Dual-phase wetting:the system has contact angles with the water-wet and oil-wet interfaces of(46±1)°and(68±1)°respectively,and makes it possible for capillarity to work fully under complex wetting conditions of the reservoir;(4)High surface activity:the interfacial tension between the system and crude oil from a tight oil reservoir in Xinjiang is 10-3–10-2 mN/m,indicating the system can effectively improve the displacement efficiency of oil in fine pore throats;(5)Demulsification and viscosity reduction:the system has a demulsification and viscosity reduction rate of more than 80%to inversely emulsified crude oil from a tight oil reservoir in Xinjiang,so it can improve the mobility of crude oil in the reservoir and wellbore.The system can be used to increase oil production by fracturing in tight reservoirs,replenish formation energy by reducing injection pressure and increasing injection rate,and enhance oil recovery by displacement and cyclic injection,providing key technical support for effective production and efficient development and recovery enhancement of tight reservoirs.

Stress-rupture measurements of cast magnesium strengthened by in-situ production of ceramic particles

We have introduced a polymer precursor into molten magnesium and then in-situ pyrolyzed to produce castings of metal matrix composites(P-MMCs)containing silicon-carbonitride(SiCNO)ceramic particles.Stress-rupture measurements of as-cast P-MMCs was performed at 350 ℃(0.69TM)to 450 ℃(0.78TM)under dead load condition corresponding to tensile stress of 2.5 MPa to 20 MPa.The time-to-fracture data were analyzed using the classical Monkman–Grant equation.The time-to-fracture is thermally activated and follows a power-law stress exponent exhibiting dislocation creep.Fractography analysis revealed that while pure magnesium appears to fracture by dislocation slip,the P-MMCs fail from the nucleation and growth of voids at the grain boundaries.