An approach for determination of lateral limit angle in kinematic planar sliding analysis for rock slopes

Planar sliding is one of the frequently observed types of failure in rock slopes.Kinematic analysis is a classic and widely used method to examine the potential failure modes in rock masses.The accuracy of planar sliding kinematic analysis is significantly influenced by the value assigned to the lateral limit angleγlim.However,the assignment ofγlim is currently used generally based on an empirical criterion.This study aims to propose an approach for determining the value ofγlim in deterministic and probabilistic kinematic planar sliding analysis.A new perspective is presented to reveal thatγlim essentially influences the probability of forming a potential planar sliding block.The procedure to calculate this probability is introduced using the block theory method.It is found that the probability is correlated with the number of discontinuity sets presented in rock masses.Thus,different values ofγlim for rock masses with different sets of discontinuities are recommended in both probabilistic and deterministic planar sliding kinematic analyses;whereas a fixed value ofγlim is commonly assigned to different types of rock masses in traditional method.Finally,an engineering case was used to compare the proposed and traditional kinematic analysis methods.The error rates of the traditional method vary from 45%to 119%,while that of the proposed method ranges between 1%and 17%.Therefore,it is likely that the proposed method is superior to the traditional one.

Development of swashplateless helicopter blade pitch control system using the limited angle direct-drive motor(LADDM)

It can be greatly beneficial to remove the swashplate of conventional helicopter, because the swashplate is usually complicated, aerodynamically resistive, and obstacle of more complex pitch control for improving performance. The present technologies for helicopter vibration reduction are usually narrow in effective range or requiring additional actuators and signal transfer links, and more effective technology is desired. Helicopter blade pitch control system, which is removed of swashplate and integrated high-frequency pitch control function for active vibration reduction, is likely the suitable solution at current technical level. Several potential implementation schemes are discussed, such as blades being directly or indirectly driven by actuators mounted in rotating frame and application of different types of actuators, especially implementation schemes of electro-mechanical actuator with or without gear reducer. It is found that swashplateless blade pitch control system based on specially designed limited angle direct-drive motor （LADDM） is a more practical implementation scheme. An experimental prototype of the finally selected implementation scheme has been designed, fabricated and tested on rotor tower. The test results show considerable feasibility of the swashplateless helicopter blade pitch control system using the LADDM.

Quality Evaluation of Image Recording Strategies for Limited Angle Tomography

In this paper we propose a new method for evaluating image recording strategies for limited angle tomography. In limited angle tomography exact three-dimensional （3-D） reconstruction is not achievable. With this method a metric for the reachable reconstruction quality by defined X-ray source trajectories is calculated. The result of our method is independent of reconstruction algorithms. Our approach is based on the gradients of the scanned volume and their grade of determinability. Compared to simulated reconstruction accuracy with simultaneous algebraic reconstruction techniques, the method of evaluation shows the same dependencies on X-ray source trajectories. By using the proposed method different source trajectories for a limited angle range are comparable with respect to the reachable reconstruction quality.

Iterative analytic extension in tomographic imaging

If a spatial-domain function has a finite support,its Fourier transform is an entire function.The Taylor series expansion of an entire function converges at every finite point in the complex plane.The analytic continuation theory suggests that a finite-sized object can be uniquely determined by its frequency components in a very small neighborhood.Trying to obtain such an exact Taylor expansion is difficult.This paper proposes an iterative algorithm to extend the measured frequency components to unmeasured regions.Computer simulations show that the proposed algorithm converges very slowly,indicating that the problem is too ill-posed to be practically solvable using available methods.

Determination of the Stable Slope Configuration of Oval-Shaped Furrow Pits

The space effects of oval-shaped furrow pit slopes were analyzed by the elastic mechanics principle.The interaction of limit equilibrium slope angle,friction coefficient,cohesion and horizontal radius of oval-shaped furrow pits has been derived.The oval trumpet-like rock mass is homogeneous and elastic while only loaded by its dead weight.The interaction indicates that the deeper an oval-shaped furrow pit is excavated,the greater the limit equilibrium slope angle.Both the theory base for reducing stripping waste rock in an oval-shaped furrow pit and the basic way to determine the configuration of a stable slope were developed from the mentioned interaction.The theory includes the preceding principles of stability analysis of slopes.Compared with the configuration determined by traditional theory of slope stability,a great quantity of stripping waste rock can be reduced by that determined in this paper under stable conditions.

Design and Range of Application of Slot Bushings with Volumetric Orifice Fields

A design of a slot bushing with a volumetric field has been developed, which allows to produce continuous fibers from melts with difficult processing characteristics in order to produce fibers with better operating characteristics. The operability of the design was confirmed when solving two problems of special technological complexity. 1. 400 and 800 orifice bushings for production of continuous fibers from the basalt melt have been developed and recommended for manufacture. 2. The process of production of continuous fibers from standard glass using 2400 orifice bushing with perforated plates instead of orifice tips without air cooling, has been realized for the first time.

STUDY ON COPYING QUALITY IN CONTOUR GRINDING

A criterion is proposed to the feasibility on radial copying grinding, i.e.the pressure angleapplying to a point on the workpiece contour to be profiled should be smaller than its angle limit.Therefore, the expressions of the angle applying to copying grinding and the angle limit to copyingmechanism are derived, with the measures taken for the quality improvement of copying movementin contour grinding discussed.