Fine quantitative characterization of high-H2S gas reservoirs under the influence of liquid sulfur deposition and adsorption

In order to clarify the influence of liquid sulfur deposition and adsorption to high-H2S gas reservoirs,three types of natural cores with typical carbonate pore structures were selected for high-temperature and high-pressure core displacement experiments.Fine quantitative characterization of the cores in three steady states(original,after sulfur injection,and after gas flooding)was carried out using the nuclear magnetic resonance(NMR)transverse relaxation time spectrum and imaging,X-ray computer tomography(CT)of full-diameter cores,basic physical property testing,and field emission scanning electron microscopy imaging.The loss of pore volume caused by sulfur deposition and adsorption mainly comes from the medium and large pores with sizes bigger than 1000μm.Liquid sulfur has a stronger adsorption and deposition ability in smaller pore spaces,and causes greater damage to reservoirs with poor original pore structures.The pore structure of the three types of carbonate reservoirs shows multiple fractal characteristics.The worse the pore structure,the greater the change of internal pore distribution caused by liquid sulfur deposition and adsorption,and the stronger the heterogeneity.Liquid sulfur deposition and adsorption change the pore size distribution,pore connectivity,and heterogeneity of the rock,which further changes the physical properties of the reservoir.After sulfur injection and gas flooding,the permeability of TypeⅠreservoirs with good physical properties decreased by 16%,and that of TypesⅡandⅢreservoirs with poor physical properties decreased by 90%or more,suggesting an extremely high damage.This indicates that the worse the initial physical properties,the greater the damage of liquid sulfur deposition and adsorption.Liquid sulfur is adsorbed and deposited in different types of pore space in the forms of flocculence,cobweb,or retinitis,causing different changes in the pore structure and physical property of the reservoir.

Transient liquid phase bonding of DD5 superalloy using a designed interlayer: microstructure and mechanical properties

Nickel based single crystal superalloy is currently widely used as the material for turbine blades in aerospace engines.However,metallurgical defects during the manufacturing process and damage during harsh environmental service are inevitable challenges for turbine blades.Therefore,bonding techniques play a very important role in the manufacturing and repair of turbine blades.The transient liquid phase(TLP)bonding of DD5 Ni-based single crystal superalloy was performed using the designed H1 interlayer.A new third-generation Ni-based superalloy T1 powder was mixed with H1 powder as another interlayer to improve the mechanical properties of the bonded joints.The res-ults show that,such a designed H1 interlayer is beneficial to the improvement of shear strength of DD5 alloy bonded joints by adjusting the bonding temperature and the prolongation of holding time.The maximum shear strength at room temperature of the joint with H1 interlayer reached 681 MPa when bonded at 1260℃for 3 h.The addition of T1 powder can effectively reduce holding time or relatively lower bond-ing temperature,while maintaining relatively high shear strength.When 1 wt.%T1 powder was mixed into H1 interlayer,the maximum room temperature shear strength of the joint bonded at 1260℃reached 641 MPa,which could be obtained for only 1 h.Considering the bonding temperature and the efficiency,the acceptable process parameter of H1+5 wt.%T1 interlayer was 1240℃/2 h,and the room tem-perature shear strength reached 613 MPa.

Synthesis of polymeric ionic liquids material and application in CO2 adsorption

We synthesized one quaternary ammonium polymeric ionic liquids（PILs）P[VBTHEA]Cl and three imidazolium PILs of P[VEIm]Br, P[VEIm]BF, P[VEIm]PFby free-radical polymerization in solution. These PILs were characterized by FT-IR,H-NMR,C-NMR, TGA, XRD and SEM. Their COadsorption capacities were measured under different pressures and temperatures by constant-volume technique. It was observed that quaternary ammonium PILs of P[VBTHEA]Cl have higher adsorption capacity for COthan those imidazolium PILs, following P[VBTHEA]Cl > P[VEIm]PF> P[VEIm]BF> P[VEIm]Br, which may be ascribed to higher positive charge density on ammonium cation than that on imidazolium cation and thus stronger interaction with CO, consistent with the results from dual-mode adsorption model that ammonium PILs have much higher CObulk absorption than imidazolium PILs. COadsorption capacity of P[VBTHEA]Cl is 9.02 mg/g under 295 K and 1 bar, which is comparable to that of some other PILs, and is much higher than that of the corresponding ILs monomer. These PILs have good adsorption selectivity for COover Nand regeneration efficiency.

Liquid crystal droplets formation and stabilization during phase transition process

The study of phase transition processes in liquid crystals(LCs)remains challenging.Most thermotropic LCs exhibit a narrow temperature range and a rapid phase transition from the isotropic(ISO)to the nematic(N)phase,which make it difficult to capture and manipulate the phase transition process.In this study,we observed the evolution of small droplets during the ISO–N phase transition in ferroelectric nematic(NF)LC RM734.After doping with metal nanoparticles(NPs),the temperature range of the phase transition broadened,and the droplets formed during the phase transition remained stable,with their diameter increasing linearly with temperature.In addition,droplets doped with NPs can be well controlled by an external electric field.This discovery not only aids in understanding the fundamental mechanisms of LC phase transitions but also provides a simple alternative method for preparing droplets,which is potentially valuable for applications in optoelectronic devices and sensors.

Ionic Liquid Modified Inorganic Nanoparticles for Gaseous Phenol Adsorption

Ionic liquid modified silica nanoparticles were synthesized using a simple silane chemistry,followed by substitution reaction. The phenol adsorption performance was tested using temperature programmed desorption technique. The experimental results reveal that the introduction of ionic liquids on the surface of silica nanoparticles can improve the adsorption capacity of phenol compared to the pure silica nanoparticles.The initial adsorption capacity reaches 0.312 mmol·g^-1 at 25 ℃ under total pressure of 0.2 bar and it decreases slightly in the following adsorption-desorption cycles. The results demonstrate that introduction of ionic liquids can improve the phenol adsorption capacity and the simple material preparation process is feasible for industrial applications.

Mechanical and corrosion properties of full liquid phase sintered WE43 magnesium alloy specimens fabricated via binder jetting additive manufacturing

This study investigates full liquid phase sintering as a process of fabrication parts from WE43(Mg-4wt.%Y-3wt.%RE-0.7wt.%Zr)alloy using binder jetting additive manufacturing(BJAM).This fabrication process is being developed for use in producing structural or biomedical devices.Specifically,this study focused on achieving a near-dense microstructure with WE43 Mg alloy while substantially reducing the duration of sintering post-processing after BJAM part rendering.The optimal process resulted in microstructure with 2.5%porosity and significantly reduced sintering time.The improved sintering can be explained by the presence of Y_(2)O_(3)and Nd_(2)O_(3)oxide layers,which form spontaneously on the surface of WE43 powder used in BJAM.These layers appear to be crucial in preventing shape distortion of the resulting samples and in enabling the development of sintering necks,particularly under sintering conditions exceeding the liquidus temperature of WE43 alloy.Sintered WE43 specimens rendered by BJAM achieved significant improvement in both corrosion resistance and mechanical properties through reduced porosity levels related to the sintering time.

Modified electronic structure and enhanced hydroxyl adsorption make quaternary Pt-based nanosheets efficient anode electrocatalysts for formic acid-/alcohol-air fuel cells

Surface/interface engineering of a multimetallic nanostructure with diverse electrocatalytic properties for direct liquid fuel cells is desirable yet challenging.Herein,using visible light,a class of quaternary Pt_(1)Ag_(0.1)Bi_(0.16)Te_(0.29)ultrathin nanosheets is fabricated and used as high-performance anode electrocatalysts for formic acid-/alcohol-air fuel cells.The modified electronic structure of Pt,enhanced hydroxyl adsorption,and abundant exterior defects afford Pt_(1)Ag_(0.1)Bi_(0.16)Te_(0.29)/C high intrinsic anodic electrocatalytic activity to boost the power densities of direct formic acid-/methanol-/ethanol-/ethylene glycol-/glycerol-air fuel cells,and the corresponding peak power density of Pt_(1)Ag_(0.1)Bi_(0.16)Te_(0.29)/C is respectively 129.7,142.3,105.4,124.3,and 128.0 mW cm^(-2),considerably outperforming Pt/C.Operando in situ Fourier transform infrared reflection spectroscopy reveals that formic acid oxidation on Pt_(1)Ag_(0.1)Bi_(0.16)Te_(0.29)/C occurs via a CO_(2)-free direct pathway.Density functional theory calculations show that the presence of Ag,Bi,and Te in Pt_(1)Ag_(0.1)Bi_(0.16)Te_(0.29)suppresses CO^(*)formation while optimizing dehydrogenation steps and synergistic effect and modified Pt effectively enhance H_(2)O dissociation to improve electrocatalytic performance.This synthesis strategy can be extended to 43 other types of ultrathin multimetallic nanosheets(from ternary to octonary nanosheets),and efficiently capture precious metals(i.e.,Pd,Pt,Rh,Ru,Au,and Ag)from different water sources.

Time-dependent effects in transient liquid phase bonding of 304L and Cp-Ti using an Ag-Cu interlayer

One of the challenges for bimetal manufacturing is the joining process.Hence,transient liquid phase(TLP)bonding was performed between 304L stainless steel and Cp-Ti using an Ag-Cu interlayer with a thickness of 75μm for bonding time of 20,40,60,and 90 min.The bonding temperature of 860℃ was considered,which is under the β transus temperature of Cp-Ti.During TLP bonding,various intermetallic compounds(IMCs),including Ti_(5)Cr_(7)Fe_(17),(Cr,Fe)_(2)Ti,Ti(Cu,Fe),Ti_(2)(Cu,Ag),and Ti_(2)Cu from 304L toward Cp-Ti formed in the joint.Also,on the one side,with the increase in time,further diffusion of elements decreases the blocky IMCs such as Ti_(5)Cr_(7)Fe_(17),(Cr,Fe)_(2)Ti,Ti(Cu,Fe)in the 304L diffusion-affected zone(DAZ)and reaction zone,and on the other side,Ti_(2)(Cu,Ag)IMC transformed into fine morphology toward Cp-Ti DAZ.The microhardness test also demonstrated that the(Cr,Fe)_(2)Ti+Ti_(5)Cr_(7)Fe_(17) IMCs in the DAZ on the side of 304L have a hardness value of HV 564,making it the hardest phase.The maximum and minimum shear strength values are equal to 78.84 and 29.0 MPa,respectively.The cleavage pattern dominated fracture surfaces due to the formation of brittle phases in dissimilar joints.

MCM-36 zeolites tailored with acidic ionic liquid to regulate adsorption properties of isobutane and 1-butene

Adsorption properties of an adsorbent or a catalyst towards adsorbates are crucial in the process of adsorption separation or catalytic reaction. Surface morphology and structure of adsorbents have a significant impact on the adsorption properties. In this study, a novel acidic ionic liquid, 1-butyl-3-(triethoxysilylpropyl)imidazolium hydrogen sulfate(i.e., [BTPIm][HSO_4]), was synthesized and subsequently grafted onto the MCM-36 zeolite for the regulation of its adsorption properties towards isobutane and 1-butene. The resultant [BTPIm][HSO_4]-immobilized MCM-36(i.e., MCM-36-IL) was characterized by FT-IR, XPS, XRD, SEM, TG/DTG and N_2 adsorption–desorption measurement. It was found that the specific surface area, micropore volume and mesopore volume of the MCM-36 support underwent a reduction upon the immobilization of ionic liquid,while the surface density of acid increased from 0.0014 to 0.0035 mmol·m^(-2). The adsorption capacity of isobutane and 1-butene on the MCM-36-IL was determined by a static volumetric method. Results demonstrated that the interaction between isobutane and MCM-36-IL was enhanced and the interaction between 1-butene and MCM-36-IL was reduced. As a result, a tunable adsorption ratio of isobutane/1-butene on MCM-36 was achieved.With the increase in surface density of acid and the tunable adsorption ratio of isobutane and 1-butene on the functionalized MCM-36, the acidic ionic liquid-immobilized zeolites are beneficial to obtain an improved reaction yield and a prolonged catalyst life in the reactions catalyzed by solid acid.

Effect of droplet characteristics on liquid-phase distribution in spray zone of internal mixing air-mist nozzle

In continuous casting production,droplet characteristics are important parameters for evaluating the nozzle atomization quality,and have a significant impact on the secondary cooling effect and the slab quality.In order to study the behavior of atomized droplets after reaching the slab surface and to optimize the spray cooling effect,the influence of droplet diameter and droplet velocity on the migration behavior of droplets in the secondary cooling zone was analyzed by FLUENT software.Results show that the droplets in the spray zone and on the slab surface are mainly concentrated in the center,thus,the liquid volume fraction in the center is higher than that of either side.As the droplet diameter increases,the region of high liquid volume fraction on the slab surface becomes wider,and the liquid phase distribution in the slab width direction becomes uneven.Although increasing the droplet velocity at the nozzle exit has little effect on droplet diffusion in the spray zone,the distribution becomes more uneven due to more liquid reaches the slab surface per unit time.A prediction formula of the maximum water flow rate on the slab surface for specific droplet characteristics was proposed based on dimensionless analysis and validated by simulated data.A nozzle spacing of 210 mm was recommended under the working conditions in this study,which ensures effective coverage of the spray water over the slab surface and enhances the distribution uniformity of water flow rate in the transverse direction.

Calculating the number of radial cracks around a wellbore fractured by liquid CO2 phase transition blasting technology

Integrating liquid CO_(2)phase transition blasting(LCPTB)technology with hydraulic fracturing(HF)methods can help reduce wellbore damage,create multiple radial fractures,and establish a complex fracture network.This approach significantly increases the recovery efficiency of low-permeability oil and gas fields.Accurately calculating the number of fractures caused by LCPTB is necessary to predict production enhancement effects and optimize subsequent HF designs.However,few studies are reported on large-scale physical model experiments in terms of a method for calculating the fracture number.This study analyzed the initiation and propagation of cracks under LCPTB,derived a calculation formula for crack propagation radius under stress waves,and then proposed a new,fast,and accurate method for calculating the fracture number using the principle of mass conservation.Through ten rock-breaking tests using LCPTB,the study confirmed the effectiveness of the proposed calculation approach and elucidated the variation rule of explosion pressure,rock-breaking scenario,and the impact of varying parameters on fracture number.The results show that the new calculation method is suitable for fracturing technologies with high pressure rates.Recommendations include enlarging the diameter of the fracturing tube and increasing the liquid CO2 mass in the tube to enhance fracture effectiveness.Moreover,the method can be applied to other fracturing technologies,such as explosive fracturing(EF)within HF formations,indicating its broader applicability and potential impact on optimizing unconventional resource extraction technologies.

Cellulose-based Polymeric Liquid Crystals as a Biomimetic Modifier for Suppressing Protein Adsorption

A novel biomimetic protein-resistant modifier based on cellulose-based polymeric liquid crystals was described（PLCs）. Two types of PLCs of propyl hydroxypropyl cellulose ester（PPC） and octyl hydroxypropyl cellulose ester（OPC） were prepared by esterification from hydroxypropyl cellulose, and then were mixed with polyvinyl chloride and polyurethane to obtain composite films by solution casting, respectively. The surface morphology of PLCs and their composite films were characterized by polarized optical microscopy（POM） and scanning electron microscopy（SEM）, suggesting the existence of microdomain separation with fingerprint texture in PLC composite films. Water contact angle measurement results indicated that hydrophilicity of PLC/polymer composite films was dependent on the type and content of PLC as well as the type of matrix due to their interaction. Using bovine serum albumin（BSA） as a model protein, protein adsorption results revealed that PLCs with protein-resistant property can obviously suppress protein adsorption on their composite films, probably due to their flexible LC state. Moreover, all PLCs and their composites exhibited non-toxicity by MTT assay, suggesting their safety for biomedical applications.

Regulation of isobutane/1-butene adsorption behaviors on the acidic ionic liquids-functionalized MCM-22 zeolite

The adsorption ratio of isobutane/1-butene on the catalyst surface is one of the most important factors for the C4 alkylation process. Regulation of isobutane/1-butene adsorption ratio on the zeolite-supported acid catalyst is a big challenge for catalyst preparation. To regulate the isobutane/1-butene adsorption ratio, four types of ionic liquid （i.e., IL） with different alkyl chain lengths and different acid group numbers were synthesized and were subsequently immobilized onto the MCM-22 zeolite. The as-synthesized IL-immobilized MCM-22 （i.e., MCM-22-IL） was characterized by FT1R, TGA, BET, XPS and XRD, and their adsorption capacities and adsorption molar ratios of isobutane to l-butene （I/O） were investigated to correlate with surface features of MCM-22-IL Results showed that the immobilization of ILs led to a decrease of specific surface area and pore volume. But the surface density of acid groups was increased and the adsorption molar ratio of isobutane/1-butene （I/O） was significantly im- proved by the immobilization of ionic liquids. The adsorption molar ratio of I/O is substantially improved from 0.75 to above 0.9 at 300 kPa upon immobilizing ILs. Although the alkyl chain length oflLs was found to have little effect on the adsorption molar ratio of I/O, the increase of acid group numbers led to a dramatic decrease in the adsorption I/O ratio. The results illustrated that immobilizing ionic liquids is an effective way to modify the textural, chemical and morphological properties of MCM-22. Accordingly, the immobilization of ionic liquids provides a novel and a feasible way to regulate the adsorption I/O ratio on an adsorbent or a solid catalyst.

AN APPROACH TO CALCULATE THE SURFACE TENSION OF THE LIQUID NITROGEN FILM ON SOLIDS FROM AN ADSORPTION ISOTHERM

The equations, used in this paper to calculate the surface tension of the liquid nitrogen film formed by the physical adsorption on many different model solids (e.g. spherical partiele, plane particle and spherical cavity pores or cylindrical pores at the openings of both ends in solid bodies), have been derived on the thermodynamie principle. The calculated results have shown that the surface tension (γ) of the adsorbed liquid nitrogen film on most of non-porous solid surfaces diminishes with the rise of the nitrogen gas pressure (p) or of the adsorbed layers (n) at 77.3K; when p reaches the vapour pressure (p_s) of the bulk liquid nitrogen, y turns into the surface tension (γ_o) of the bulk liquid nitrogen; whgn p /p, 【0.98, there is an obvious difference between γ and γ_O.

Methylene Blue Dye Adsorption onto Polyoxometalate Ionic Liquid Supported on Bentonite: Kinetic, Equilibrium and Thermodynamic Studies

The potential of polyoxometalate ionic liquid POM-IL supported on low-cost and available eco-friendly Saudi raw bentonite in the adsorption of MB cationic dye was investigated. For this purpose, TOAx[α-XW11O39]@Bentonite (X = Si, P;TOA = TetraOctylAmmonium), namely SWB and PWB were prepared and characterized by IR, XRD, XRF, SEM, TEM and BET. Batch adsorption experiments showed that SWB and PWB have higher adsorption capacity than the raw bentonite with an enhancement of about 37% for SWB. The adsorption capacities of both SWB and PWB improved with increasing contact time and temperature and decreased with higher salt concentration in solution. The pH is shown to have insignificant effect on the adsorption of MB onto SWB and PWB. This result is quite meaningful in the adsorption process application since it makes pH complicated adjustment of the discharged contaminated water before treatment unnecessary. The Kinetic study expressed that the pseudo-second-order model described the adsorption process better than the pseudo first order. The experimental isotherm data were found to fit the Langmuir model compared to the Freundlich model with a maximum adsorption capacity 277.78 mg/g and 113.6 for PWB and SWB respectively. The thermodynamic parameters illustrated that the adsorption process was favorable, spontaneous and endothermic.

Apparent Active Adsorption Force at a Solid-Liquid Interface with Active Adsorption

The paper presents a new relationship between the three surface tensions on the solid-liquid-vapor interface, γ_(sl)-γ_(sv)+γ_(lv)cosθ=βin order to understand the wetting on the liquid-solid interface in the case of active adsorption.The authors suggest a new force“apparent active adsorption force”βto take part in the balance at the three interface lines of contact in the solid-liquid-vapor phases,its dimen- sion isβ=Σα_iRT(Γ_i^(sl)-Γ_i^(sv)+Γ_i^(lv)cosθ),and its direction is dependent on the sign of β,whenβis a positive, the direction is agree with surface tension of the sol- id-vapor interface γ and vice versa.

A solid-phase extraction approach for the identification of pharmaceutical–sludge adsorption mechanisms

It is important to understand the adsorption mechanism of chemicals and active pharmaceu-tical ingredients （API） on sewage sludge since wastewater treatment plants are the last barrier before the release of these compounds to the environment. Adsorption models were developed considering mostly hydrophobic API-sludge interaction. They have poor predictive ability, especially with ionisable compounds. This work proposes a solid-phase extraction （SPE） approach to estimate rapidly the API-sludge interaction. Sludge-filled SPE cartridges could not be percolated with API spiked mobile phases so different powders were tested as SPE sludge supports. Polytetrafluoroethylene （PTFE） was selected and tested at different PTFE/sludge ratios under eight different adsorption conditions with three API ionisable compounds. The PTFE/sludge mixtures with 50% or less sludge could be used in SPE mode for API sorption studies with methanol/water liquid phases. The results gave insights into API-sludge interactions. It was found that π-π, hydrogen-bonding and charge-charge interactions were as important as hydrophobicity in the adsorption mechanism of charged APIs on sludge.

Formation and evolution characteristics of bcc phase during isothermal relaxation processes of supercooled liquid and amorphous metal Pb

The formation and evolution characteristics of bcc phase during the isothermal relaxation processes for supercooled-liquid and amorphous Pb were investigated by molecular dynamics simulation and cluster-type index method （CTIM）. It is found that during the relaxation process, the formation and evolution of bcc phase are closely dependent on the initial temperature and structure. During the simulation time scale, when the initial temperature is in the range of supercooled liquid region, the bcc phase can be formed and kept a long time; while it is in the range of glassy region, the bcc phase can be formed at first and then partially transformed into hcp phase; when it decreases to the lower one, the hcp and fcc phases can be directly transformed from the glassy structure without undergoing the metastable bcc phase. The Ostwald＇s ＂step rule＂ is impactful during the isothermal relaxation process of the supercooled and glassy Pb, and the metastable bcc phase plays an important role in the precursor of crystallization.

Preparation of TiO_2/ITO film by liquid phase deposition and its photoelectrocatalytic activity for degradation of 4-aminoantipyrine

A thin layer of TiO2 film was deposited on ITO surface via the liquid phase deposition （LPD） process. The photocurrent and electrochemical impedance spectroscopy （EIS） measurements indicated that the as-prepared LPD TiO2/ITO film had an excellent photoelectrochemical performance, which showed a sensitive and rapid response to the UV irradiation. The photogenerated electron-hole pairs could be effectively separated by applying an external bias to the TiO2 film electrode. The LPD TiO2/ITO film was employed to study the photoelectrocatalytic （PEC） degradation of 4-aminoantipyrine. Compared with other techniques, the PEC technique based on such a LPD film electrode had a synergetic effect for 4-aminoantipyrine degradation. When the applied bias potential was＋0.8 V and the supporting electrolyte concentration of Na2SO4 was 0.1 mol/L, the highest degradation efficiency within 120 min could reach 95%for 0.1 mmol/L 4-aminoantipyrine solution at pH 2.0.

PEG-combined liquid phase synthesis and electrochemical properties of carbon-coated Li_3V_2(PO_4)_3

The carbon-coated monoclinic Li3V2(PO4)3(LVP) cathode materials were successfully synthesized by liquid phase method using PEG as reducing agent and carbon source. The effects of relative molecular mass of PEG on the properties of Li3V2(PO4)3/C were evaluated by X-ray diffraction(XRD), scanning electron microscope(SEM) and electrochemical performance tests. The SEM images show that smaller size particles are obtained by adding larger and smaller PEGs. The electrochemical cycling of Li3V2(PO4)3/C prepared by both PEG200 and PEG20 k has a high initial discharge capacity of 131.1 mA·h/g at 0.1C during 3.0-4.2 V, and delivers a reversible discharge capacity of 123.6 m A·h/g over 30 cycles, which is better than that of other samples. The improvement in electrochemical performance is caused by its improved lithium ion diffusion coefficient for the macroporous morphology, which is verified by cyclic voltammetry(CV) and electrochemical impedance spectroscopy(EIS).