High Cr white cast iron/carbon steel bimetal liner by lost foam casting with liquid-liquid composite process

Liners in wet ball mill for mineral processing industry must bear abrasive wear and corrosive wear, and consequently,the service life of the liner made from traditional materials,such as Hadfield steel and alloyed steels,is typically less than ten months.Bimetal liner,made from high Cr white cast iron and carbon steel,has been successfully developed by using liquid-liquid composite lost foam casting process.The microstructure and interface of the composite were analyzed using optical microscope,SEM,EDX and XRD.Micrographs indicate that the boundary of bimetal combination regions is staggered like dogtooth,two liquid metals are not mixed,and the interface presents excellent metallurgical bonding state.After heat treatment,the composite liner specimens have shown excellent properties,including hardness>61 HRC,fracture toughnessα k >16.5 J·cm-2 and bending strength >1,600 MPa.Wear comparison was made between the bimetal composite liner and alloyed steel liner in an industrial hematite ball mill of WISCO,and the results of eight-month test in wet grinding environment have proved that the service life of the bimetal composite liner is three times as long as that of the alloyed steel liner.

Exploring Nutritional Compositions,Volatile Compounds,Health Benefits,Emerging Processing Technologies,and Potential Food Products of Glutinous Rice:A Review

Glutinous rice(Oryza sativa var.glutinosa)stands out as one of the most popular rice varieties globally,amidst thousands of rice cultivars.Its increasing popularity is attributed to its rich nutritional compositions and health benefits.This review aims to summarize the nutritional compositions,volatile compounds,and health benefits of glutinous rice.Further,in-depth studies are necessary to explore the utilization of glutinous rice in enhancing processing technologies and developing new food products.Glutinous rice has been shown to possess numerous health benefits,including antioxidant activity,bioactive compounds,anti-cancer properties,anti-inflammatory effects,anti-diabetic potential,and cholesterol-lowering effects.Besides its nutritional compositions,the major volatile compounds identified in glutinous rice could serve as a functional food for human consumption.Emerging processing technologies related to glutinous rice are elaborated to improve the latest developments for incorporating them into various food products.

High energy density in ultra-thick and flexible electrodes enabled by designed conductive agent/binder composite

Thick electrodes can increase incorporation of active electrode materials by diminishing the proportion of inactive constituents,improving the overall energy density of batteries.However,thick electrodes fabricated using the conventional slurry casting approach frequently exhibit an exacerbated accumulation of carbon additives and binders on their surfaces,invariably leading to compromised electrochemical properties.In this study,we introduce a designed conductive agent/binder composite synthesized from carbon nanotube and polytetrafluoroethylene.This agent/binder composite facilitates production of dry-process-prepared ultra-thick electrodes endowed with a three-dimensional and uniformly distributed percolative architecture,ensuring superior electronic conductivity and remarkable mechanical resilience.Using this approach,ultra-thick LiCoO_(2)(LCO) electrodes demonstrated superior cycling performance and rate capabilities,registering an impressive loading capacity of up to 101.4 mg/cm^(2),signifying a 242% increase in battery energy density.In another analytical endeavor,time-of-flight secondary ion mass spectroscopy was used to clarify the distribution of cathode electrolyte interphase(CEI) in cycled LCO electrodes.The results provide unprecedented evidence explaining the intricate correlation between CEI generation and carbon distribution,highlighting the intrinsic advantages of the proposed dry-process approach in fine-tu ning the CEI,with excellent cycling performance in batteries equipped with ultra-thick electrodes.

Inherent relationship between process parameters,crystallization and mechanical properties of continuous carbon fiber reinforced PEEK composites

High-performance thermoplastic composites have been developed as significant structural materials for cutting-edge equipment in the aerospace and defence fields.However,the internal mechanism of processing parameters on mechanical properties in the manufacturing process of thermoplastic composite structures is still a serious challenge.The purpose of this study is to investigate the process/crystallization/property relationships for continuous carbon fiber(CF)reinforced polyether-ether-ketone(PEEK)composites.The composite laminates are fabricated according to orthogonal experiments via the thermoforming method.The mechanical performance is investigated in terms of crystallization properties and fracture morphology characterizations.Experimental results show that the mechanical performance and crystallization properties of thermoplastic composites are significantly affected by the coupling of processing parameters.The increased molding temperature,pressure,and holding time improve the degree of fiber/matrix infiltration and affect the crystallinity and crystalline morphology of the matrix,which further influences the mechanical properties of the composites.This is reflected in the test results that crystallinity has an approximately linear effect on mode-I interlaminar fracture toughness and transverse flexural modulus.As well as the higher molding temperature can destroy the pre-existent crystals to improve the toughness of the matrix,and the well-defined crystalline structures can be observed when fabricated at higher temperatures and longer periods of holding time.

Surface metal-matrix composites based on AZ91 magnesium alloy via friction stir processing:A review

This monograph presents an overview of friction stir processing(FSP)of surface metal-matrix composites(MMCs)using the AZ91 magnesium alloy.The reported results in relation to various reinforcing particles,including silicon carbide(SiC),alumina(Al_(2)O_(3)),quartz(SiO_(2)),boron carbide(B_(4)C),titanium carbide(TiC),carbon fiber,hydroxyapatite(HA),in-situ formed phases,and hybrid reinforcements are summarized.AZ91 composite fabricating methods based on FSP are explained,including groove filling(grooving),drilled hole filling,sandwich method,stir casting followed by FSP,and formation of in-situ particles.The effects of introducing second-phase particles and FSP process parameters(e.g.,tool rotation rate,traverse speed,and the number of passes)on the microstructural modification,grain refinement,homogeneity in the distribution of particles,inhibition of grain growth,mechanical properties,strength–ductility trade-off,wear/tribological behavior,and corrosion resistance are discussed.Finally,useful suggestions for future work are proposed,including focusing on the superplasticity and superplastic forming,metal additive manufacturing processes based on friction stir engineering(such as additive friction stir deposition),direct FSP,stationary shoulder FSP,correlation of the dynamic recrystallization(DRX)grain size with the Zener–Hollomon parameter similar to hot deformation studies,process parameters(such as the particle volume fraction and external cooling),and common reinforcing phases such as zirconia(ZrO_(2))and carbon nanotubes(CNTs).

Correlations between mineral composition and mechanical properties of granite using digital image processing and discrete element method

This study investigated the correlations between mechanical properties and mineralogy of granite using the digital image processing(DIP) and discrete element method(DEM). The results showed that the X-ray diffraction(XRD)-based DIP method effectively analyzed the mineral composition contents and spatial distributions of granite. During the particle flow code(PFC2D) model calibration phase, the numerical simulation exhibited that the uniaxial compressive strength(UCS) value, elastic modulus(E), and failure pattern of the granite specimen in the UCS test were comparable to the experiment. By establishing 351 sets of numerical models and exploring the impacts of mineral composition on the mechanical properties of granite, it indicated that there was no negative correlation between quartz and feldspar for UCS, tensile strength(σ_(t)), and E. In contrast, mica had a significant negative correlation for UCS, σ_(t), and E. The presence of quartz increased the brittleness of granite, whereas the presence of mica and feldspar increased its ductility in UCS and direct tensile strength(DTS) tests. Varying contents of major mineral compositions in granite showed minor influence on the number of cracks in both UCS and DTS tests.

CATHODIC PROCESS AND WEAR RESISTANCE OF ELECTRO-DEPOSITED RE-Ni-W-P-SiC COMPOSITE COATING

Cathodic deposition current density of the composite coatings increases when SiC par-ticles and rare earth (RE) were added in the bath, which is profitable for Ni- W-P alloy to deposit in the cathod, forming Ni-W-P-SiC and RE-Ni-W-P-SiC composite coatings. On the contrary, the addition of PTFE in the bath decreases cathodic deposition current density of the coatings. The current density increases a little when the amount of RE is 7-9g/l; however, the current density increases greatly when the amount of RE is increased to 11-13g/l. Bui ij the amount of RE is raised further, the current density decreases. Hardness and wear resistance of RE-Ni-W-P-SiC composite coating have been studied, and the results show that the hardness and wear resistance of RE-Ni-W-P-SiC composite coating increase with increasing heat treatment tempera-ture, which reach peak values at 400℃; while the hardness and wear resistance of the coating decrease with the rise of heat treated temperature continuously.

Study on liquid-liquid bimetal composite casting hammers

Crusher hammers for the mineral processing industry must meet the demands of both high wear resistance at the hammer head and high impact toughness at the hammer handle. The crusher hammers made of Hadfield steel have typically low service life of less than 40 hours. To solve the problem, a kind of bimetal crusher hammers made of high chromium cast iron(HCCI) and low alloy steel(LAS) has been successfully developed by using liquid-liquid composite casting. The microstructure and composite interface bonding was analyzed using optical microscope, SEM, EDX and XRD. Micrographs indicate that the composite interface is metallurgically bonded with a zigzag shape across the boundary and without unbound region or void. After heat treatment, the composite hammers have shown excellent properties. The hardness of HCCI is at least 63 HRC and its αk is greater than 3.5 J·cm-2; the hardness of LAS is greater than 35 HRC and its αk is no less than 80 J·cm-2. Diffusion of elements takes place at the interface and forms a transition region. The micro hardness increases from LAS to the interface and then to HCCI. Wear comparison was made separately between the bimetal composite hammer and a Hadfield steel hammer in two quarries of Jilin province and Liaoning province. The results showed that the liquid-liquid bimetal composite hammers did not have the falling off of hammer head or impact fracture phenomenon, and their service life was 3.75 times as long as that of the Hadfield steel hammers.

Reactive Processing and Mechanical Properties of Al/SiC_P Composite

The reactive process for Al/SiC P composite was studied. SiC particles were in situ coated by the exothermal reaction of SiC Ti powder compact in Al melt bath, and easily incorporated into Al melt. The detailed study was carried out to understand the microstructures of the reacted SiC particles. During the reaction and consequent mixing, the successive processes include in situ coating on the reacted SiC particles, coat dissolution and SiC P splitting. The tensile mechanical properties of 6013Al/SiC P composite processed by the present technology showed that the reacted SiC P considerably reinforced the 6013 matrix.

Structures and Properties of Iron Matrix Composites with Tungsten Carbide Particle by EPC-V Process

In this paper the Expendable Pattern Casting with dry sand Vacuum(EPC-V) process is used to manufacture iron matrix composites with tungsten carbide particle.Microstructures of the composites layers were analyzed.The abrasive wear resistance of the composites layers were tested and compared with that of high chromium cast iron.The results show that the iron matrix composites with tungsten carbide particle have high hardness.The abrasive wear resistance of composites with tungsten carbide particle is higher than that of high chromium cast iron.The properties of the matrix materials have been improved remarkably.

THE EROSIVE PROCESS IN ABRASIVE WATERJET CUTTING OF POLYMER MATRIX COMPOSITES

A study is carried out which analyzes the machinability of polymer matrix composites under an abrasive waterjet (AWJ) and the associated erosive process or mechanism. It shows that AWJ cutting can produce good quality kerf at high production rate if the cutting parameters are properly selected. A scanning electron microscopy (SEM) analysis of the cut surfaces reveals that the erosive process for the matrix material (resin) involves shearing and ploughing as well as intergranular cracking, while shearing is a dominant process for cutting the fibres in the upper cutting region but the fibers are mostly pulled out in the lower region.

IN SITU PROCESSING OF Al_(2)O_(3) WHISKERS REINFORCED Ti-Al INTERMETALLIC COMPOSITES

In situ Al2O3 whiskers reinforced Ti-Al intermetallic composites were fabricated at ~1200℃ by reaction sintering of cold-consolidated fillets consisting mainly of Ti, Al, and different additives. The phases and microstructures of the sintered composites were characterized using X-ray diffraction (XRD) and scanning electron microscopy (SEM) coupled with energy dispersive spectroscopy (EDS). The process of synthesis was investigated using differential thermal analysis (DTA). The effects of processing parameters and additives on the microstructures of the composites and the development of whisker were examined. It is found that the morphology of the whisker is strongly influenced by the additives, the exothermal reaction process, and the processing parameters.

Fabrication of AA7005/TiB2-B4C surface composite by friction stir processing: Evaluation of ballistic behaviour

The present work aims to enhance the ballistic resistance of AA7005 alloy by incorporating the TiB2 and B4C ceramic reinforcement particles. Surface composites with different weight fractions of TiB2 and B4C particles were processed by friction stir processing. Micro-hardness and depth of penetration tests were carried out to evaluate the ballistic properties of the surface composites. The surface hardness of the composite was found to be nearly 70 HV higher than base alloy. The depth of penetration of the steel projectile was 20e26mm in the composites as compared to 37mm in the base alloy. Ballistic mass efficiency factor of the surface composite was found to be 1.6 times higher than base alloy. This is mainly attributed to the dispersion strengthening from the reinforcement particles.

Coating process of multi-material composite sand mold 3D printing

Sand mold 3 D printing technology is an advanced manufacturing technology which has great flexible manufacturing ability. A multi-material composite sand mold can control the temperature field of metallic parts during the pouring process, while the current sand mold 3 D printing technology can only fabricate a single material sand mold. The casting temperature field can not be adjusted by using single sand mold material with isotropous heat exchange ability during the pouring process. In this work, a kind of novel coating device was designed. Multi-material composite sand molds could be manufactured using the coating device according to the casting process demands of the final parts. The influences of curing agent content, coating velocity and scraper shape on compactness and surface roughness of the sand layer(silica sand and zircon sand) were studied. The shapes and sizes of transition intervals of two kinds of sand granules were also tested. The results show that, with the increase of the added volume of curing agent, the compactness of sand layer reduces and the surface roughness value rises. With the increase of the velocity of the coating device, the compactness of sand layer reduces and the surface roughness value rises similarly. In addition, the scraper with a dip angle of 72 degrees could increase the compactness value of the sand layer. The criteria of quality parmeters of the coating procedure are obtained. That is, the surface roughness(δ) of sand layer should be equal to or lesser than half of main size of the sand particles(Dm). The parameter H of the coating device which is the distance between the base of hopper and the surface of sand layer impacts the size of transition zone. The width of the transition zone is in direct proportion to the parameter H, qualitatively. Through the optimization of the coating device, high quality of multi-material sand layers can be obtained. This will provide a solution in manufacturing the multi-material composite sand mold.

Magnesium based surface metal matrix composites by friction stir processing

Surface metal matrix composites(MMCs)are a group of modern engineered materials where the surface of the material is modified by dispersing secondary phase in the form of particles or fibers and the core of the material experience no change in chemical composition and structure.The potential applications of the surface MMCs can be found in automotive,aerospace,biomedical and power industries.Recently,friction stir processing(FSP)technique has been gaining wide popularity in producing surface composites in solid state itself.Magnesium and its alloys being difficult to process metals also have been successfully processed by FSP to fabricate surface MMCs.The aim of the present paper is to provide a comprehensive summary of state-of-the-art in fabricating magnesium based composites by FSP.Influence of the secondary phase particles and grain refinement resulted from FSP on the properties of these composites is also discussed.

COMPOSITE ANALYSIS OF SUMMER MONSOON ONSET PROCESS OVER SOUTH CHINA SEA

Based on the method of composite analysis, the onset process and preceding signs of summer monsoon over the South China Sea (SCS) is investigated. The result indicates that convection activities appear first over the Indo-China Peninsula prior to the onset of the monsoon, then around the Philippines just at the point of onset, implying that the convection activities around the Philippines serve as one of the reasons leading to the SCS monsoon onset. Before the SCS monsoon onset, the equatorial westerly over the Indian Ocean (75(E ～ 95(E ) experiences noticeable enhancement and plays an important role on the SCS monsoon onset. It propagates eastward rapidly and causes the establishment and strengthening of equatorial westerly in the southern SCS, on the one hand, it results in the migration southward of the westerly on south side of the south-China stationary front by means of shift northeastward of the westerly and convection over the Bay of Bengal, on the other. Further study also shows that the intensification of equatorial westerly in the Indian Ocean (75(E ～ 95(E) and the southern SCS is closely related to the reinforcement of the Southern-Hemisphere Mascarene high and Australian high, and cross-equatorial flow northward around Somali, at 85(E and 105(E, respectively.

Optimization of Extraction Process of Clerodendrum philippinum Schauer var. simplex Mlodenke Total Flavonoids(CPTF) by Central Composite Design-Response Surface Methodology

[Objectives] The research aimed to optimize extraction process of Clerodendrum philippinum Schauer var. simplex Mlodenke total flavonoids( CPTF),and provide reference for its development and utilization. [Methods] Based on single-factor test,ethanol concentration,extraction temperature and extraction time were taken as independent variables,and total flavonoids yield was taken as dependent variable. The test was conducted according to central composite design principle. Multivariate linear regression and binomial equation fitting of the result were conducted,and extraction process of CPTF was optimized by using response surface methodology. [Results]The optimal extraction process of CPTF was as below: ethanol concentration 54. 76%,extraction temperature 83. 92℃,extraction time 102. 64 min,solid-liquid ratio 1:20,extraction for twice. [Conclusions] The extraction process of CPTF by central composite design-response surface methodology was simple and feasible,with reliable prediction result,which was suitable for industrial production.

Preparation of ZrN(ZrON)-SiAION Composite Ceramics via a Pressureless Sintering Process

ZrN-SiAlON composite materials were synthesized at 1 550 ℃ for 6 h via a carbothermal reduction nitridation route using fly ash （≤74 μm）,zircon （≤ 44 μm） and active carbon as starting materials.The processed ZrN-SiAlON composite micropowders were mixed with polyvinyl alcohol as binder to prepare ZrN （ZrON）-SiAlON composite ceramics by carbon-embedded pressureless firing at 1 450,1 500 and 1 550 ℃ for 1 h,respectively.Influences of firing temperature on the phase compositions,microstructure and sintering properties of the ceramics were investigated.The results show that：（1） β-SiAlON based composite ceramics with different compositions can be prepared by controlling firing temperature,and the main crystalline phases of the specimen fired at 1 550 ℃ for 1 h involve ZrN,ZrON and β-SiAlON （z =2,Si4Al2O2N6）; （2） ZrN （ZrON）,β-SiAlON and a Fe-Si based compound can be observed in the microstructures of the specimens fired at different temperatures.ZrN （ZrON） particles distribute homogeneously in the β-SiAlON matrix; （3） raising firing temperature can increase the shrinkage ratio of the ceramics,and the volume shrinkage ratio increases from 19.4％ to 40.3％ when the firing temperature rises from 1 450 to 1 550 ℃.

Deformation Processed Cu-15 wt pct Cr Composite Synthesized by Hot Hydrostatic Extrusion of Mechanical Milled Powders

A novel technique was developed for the preparation of Cu-15 wt pct Cr composite with high strength and conductivity. The composite powders with refined microstructure and curly lamellae strengthening phase was first prepared by mechanical milling in favorite milling time and then were hot hydrostatic extruded after pre-densification with sintering or hot pressing. It was shown that the extrusion densified the composite powders well and at the same time the chaos curled strengthening phase was aligned into lines and further deformed as strengthening ribbons. The deformation processed Cu-15 wt pct Cr composite prepared by this technique is of superior conductivity, strength and thermal stability.

Assessment of Ti-6Al-4V particles as a reinforcement for AZ31 magnesium alloy-based composites to boost ductility incorporated through friction stir processing

Poor ductility is the primary concern of magnesium matrix composites(MMCs)inflicted by non-deformable ceramic particle reinforcements.Metal particles which melt at elevated temperature can be used as reinforcement to improve the deformation characteristics.Ti-6Al-4V particles reinforced AZ31 MMCs were produced through friction stir processing(FSP)which was carried out in a traditional vertical milling machine.The microstructural features as well as the response to external tensile load were explored.A homogenous distribution of Ti-6Al-4V was achieved at every part of the stir zone.There was no chemical decomposition of Ti-6Al-4V.Further,Ti-6Al-4V did not react with Al and Zn present in AZ31 alloy to form new compounds.A continuous strong interface was obtained around Ti-6Al-4V particle with the matrix.Ti-6Al-4V particles underwent breakage during processing due to severe plastic strain.There was a remarkable refinement of grains in the composite caused by dynamic recrystallization in addition to the pinning of smaller size broken particles.Dense dislocations were observed in the matrix because of plastic deformation and the associated strain misfit.Ti-6Al-4V particles improved the tensile behavior and assisted to obtain appreciable deformation before fracture.Brittle mode of failure was avoided.