Structural, Optical and Photocatalytic Properties of Cu2+ Doped ZnO Nanorods with Using HMTA Solvent Prepared by Hydrothermal Method

In this experiment, Cu2+ doped ZnO (Cu-ZnO) nanorods materials have been fabricated by hydrothermal method. Cu2+ ions were doped into ZnO with ratios of 2, 5 and 7 mol.% (compared to the mole’s number of Zn2+). The hexamethylenetetramine (HMTA) solvent used for the fabrication of Cu-ZnO nanorods with the mole ratio of Zn2+:HMTA = 1:4. The characteristics of the materials were analyzed by techniques, such as XRD, Raman shift, SEM and UV-vis diffuse reflectance spectra (DRS). The photocatalytic properties of the materials were investigated by the decomposition of the methylene blue (MB) dye solution under ultraviolet light. The results show that the size of Cu-ZnO nanorods was reduced when the Cu2+ doping ratio increased from 2 mol.% to 7 mol.%. The decomposition efficiency of the MB dye solution reached 92% - 97%, corresponding to the Cu2+ doping ratio changed from 2 - 7 mol.% (after 40 minutes of ultraviolet irradiation). The highest efficiency for the decomposition of the MB solution was obtained at a Cu2+ doping ratio of 2 mol.%.

Continuously Doping Bi_(2)Sr_(2)CaCu_(2)O_(8+δ)into Electron-Doped Superconductor by CaH_(2)Annealing Method

As a typical hole-doped cuprate superconductor,Bi_(2)Sr_(2)CaCu_(2)O_(8+δ)(Bi2212)carrier doping is mostly determined by its oxygen content.Traditional doping methods can regulate its doping level within the range of hole doping.Here we report the first application of CaH_(2)annealing method in regulating the doping level of Bi2212.By continuously controlling the anneal time,a series of differently doped samples can be obtained.The combined experimental results of x-ray diffraction,scanning transmission electron microscopy,resistance and Hall measurements demonstrate that the CaH_(2)induced topochemical reaction can effectively change the oxygen content of Bi2212 within a very wide range,even switching from hole doping to electron doping.We also found evidence of a low-T_c superconducting phase in the electron doping side.

Study of the Conductance Characteristic of Doped Polymer by Monte Carlo Method

The conduct mechanism of the doped polymer is considered. In an asymmetrysystem composed of high polymer and doping conductive matte, chain or congeries framework will beformed between the conductive particles to improve the conductance characteristic. In thisprocession, the conductive particles interact to each other. In this paper, we describe theconductance of the doped polymer by Monte Carlo method. The results accord with the experimentsquite well. It can be concluded that there is an evident change of doped polymer from nonconductorto metal.

Effects of Ni doping contents on photocatalytic activity of B-BiVO_4 synthesized through sol-gel and impregnation two-step method

To enhance the photocatalytic activity of B-BiVO4,Ni-doped B?BiVO4photocatalyst(Ni-B-BiVO4)was synthesized through sol-gel and impregnation method.The photocatalysts were characterized by XPS,XRD,SEM,EDS,BET and UV-Vis DRS techniques.The results showed that single or double doping did not change the crystalline structure and morphology,but the particle size decreased with Ni doping.The band gap energy absorption edge of Ni-B-BiVO4shifted to a longer wavelength compared with undoped,B or Ni single doped BiVO4.More V4+and surface hydroxyl oxygen were observed in BiVO4after Ni-B co-doping.When the optimal mass fraction of Ni is0.30%,the degradation rate of MO in50min is95%for0.3Ni-B-BiVO4sample which also can effectively degrade methyl blue(MB),acid orange(AOII)II and rhodamine B(RhB).The enhanced photocatalytic activity is attributed to the synergistic effects of B and Ni doping.

Coupling of discrete-element method and smoothed particle hydrodynamics for liquid-solid flows

Particle based methods can be used for both the simulations of solid and fluid phases in multiphase medium, such as the discrete-element method for solid phase and the smoothed particle hydrodynamics for fluid phase. This paper presents a computational method combining these two methods for solid-liquid medium. The two phases are coupled by using an improved model from a reported Lagrangian-Eulerian method. The technique is verified by simulating liquid-solid flows in a two-dimensional lid-driven cavity.

Effects of La^(3+) doping on MnZn ferrite nanoscale particles synthesized by hydrothermal method

MnZn ferrite nanoscale particles were synthesized by hydrothermal method. The effects of amount of addition La3+ on the products were discussed. The product was characterized by X-ray diffraction （XRD） and transmission electron microscope （TEM）. The results show that the sample with 0.2% La3+（mass fraction） or without La3+ has only spinel phase, but the sample with mass fraction of La3+ exceeding 0.4% posses second phase besides the spinel one; and the nano-MnZn ferrites change from cube to hexagon when the mass fractions of La3+ is up to （1.2%.） TEM image of the sample with 1.2% La3+ indicates that the homogeneous hexagonal crystal is obtained and the particles are larger than those of undoped; the addition of La3+ has great influence on the crystallization of hydrothermal process and can change the shape of particles and improve their growth. The saturation magnetization of the sample with 1.2% La3+ (2.64 A·m2·kg-1) is lower than that of undoped (17.54 (A·m2·kg-1)) and it behaves superparamagnetically.

N-doped NaTaO3 synthesized from a hydrothermal method for photocatalytic water splitting under visible light irradiation

NaTaONcatalysts were synthesized by a hydrothermal（H） and a solid-state（S） methods in this study.The H-and S-NaTaONsamples were characterized by X-ray diffraction（XRD）, scanning electron microscopy（SEM）, transmission electron microscopy（TEM）, UV–visible（UV–vis） diffuse reflectance spectroscopy, and photoluminescence（PL） spectroscopy. The XRD patterns of the H-and S-samples showed peaks indexed to the pure phase of perovskite NaTaOand minor peaks assignable to TaNat various synthesis temperatures. Substitution of oxygen by nitrogen ions causes the light absorption of the H-and S-NaTaONsamples to be extended to the 600–650 nm region, thus making the samples visible-light active. The NaTaONsamples exhibited photocatalytic activity for Hand Oevolution from aqueous methanol and silver nitrate solutions under visible-light irradiation. The UV–vis and PL spectra of the Hand S-catalysts revealed the presence of cationic vacancies and reduced metallic species, which acted as recombination centers. These results demonstrated that the preparation method plays a critical role in the formation of defect states, thereby governing the photocatalytic activity of the NaTaONcatalysts.

Synthesis and Characterization of Y-Doped Mesoporous CeO_2 Using A Chemical Precipitation Method

Using cetyltrimethylammonium bromide （CTAB） as the template agent, cerium nitrate as the cerium resource, yttrium nitrate as the yttrium resource, and ammonium carbonate as the precipitating agent, mesoporous CeO2 powders doped with different yttrium contents were successfully synthesized using a chemical precipitation method, under an alkalescent condition. Properties of the obtained samples were characterized and analyzed with X-ray diffraction （XRD）, energy dispersive analysis of X-rays （EDAX）, transmission electron microscopy （TEM）, infrared （IR） absorbance, and the BET method. For the prepared samples with 20% （molar ratio） Y-doped content, a BET specific surface area of 106. 6 m^2 · g^- 1, with an average pore size of3~27 nm were obtained. XRD patterns showed that the doped samples were with a cubic fluorite structure. TEM micrographs revealed that the doped samples showed a spherical morphology with a diameter ranging from 20 to 30 nm and a round pore shape. IR results indicated that the Ce-O-Ce vibration intensity decreased as the Y-doped content increased. N2 adsorption-desorption isotherms showed that the samples possessed typical mesopore characteristics. The average pore size of the samples decreased alter mesoporous CeO2 was doped with yttrium, and the average pore size decreased largely as the Y-doped content increased.

Synthesis and electrochemical properties of dual doped spinels LiNi_xAl_yMn_(2-x-y)O_4 via facile novel chelated sol–gel method as possible cathode material for lithium rechargeable batteries

LiMnOand LiNiAlyMnO（x= 0.50;y = 0.05-0.50） powders have been synthesized via facile solgel method using Behenic acid as active cheiating agent.The synthesized samples are subjected to physical characterizations such as thermo gravimetric analysis（TG/DTA）,X-ray diffraction（XRD）,Fourier transform infrared spectroscopy（FT-IR）,field-emission scanning electron microscopy（FESEM）,transmission electron microscopy（TEM） and electrochemical studies viz.,galvanostatic cycling properties,electrochemical impedance spectroscopy（EIS） and differential capacity curves（dQ/dE）.Finger print XRD patterns of LiMnOand LiNiAlMnOfortify the high degree of crystallinity with better phase purity.FESEM images of the undoped pristine spinel illustrate uniform spherical grains surface morphology with an average particle size of 0.5 μm while Ni doped particles depict the spherical grains growth（50nm） with ice-cube surface morphology.TEM images of the spinel LiMnOshows the uniform spherical morphology with particle size of（100 nm） while low level of Al-doping spinel（LiNio.5Alo.05Mn1.45O4） displaying cloudy particles with agglomerated particles of（50nm）.The LiMnOsamples calcined at 850℃ deliver the discharge capacity of 130 mAh/g in the first cycle corresponds to 94%coiumbic efficiency with capacity fade of 1.5 mAh/g/cycle over the investigated 10 cycles.Among all four dopant compositions investigated,LiNiAlMnOdelivers the maximum discharge capacity of 126 mAh/g during the first cycle and shows the stable cycling performance with low capacity fade of 1 mAh/g/cycle（capacity retention of 92%） over the investigated 10 cycles.Electrochemical impedance studies of spinel LiMnOand LiNiAlMnOdepict the high and low real polarization of 1562 and 1100 Ω.

Elimination of hard aggregation of bismuth-doped tin dioxide nanometer powders prepared by wet chemical method

Bismuth-doped tin dioxide （BTO） nanometer powders were prepared by the wet chemical method using tin tetrachloride （SnCl4）, bismuth nitrate [Bi（NO3） 3 ] and ammonia as raw materials. Non-bridge hydroxides and capillary force between particles were found to be key factors causing hard aggregation of BTO through analyzing the formation mechanism of hard aggregation. The hard aggregation of BTO was eliminated effectively when the Bi-Sn precursor （BSP） was treated with post processing including dispersing with ultrasonic wave, refluxing and distilling with addition of n-butanol and benzene （DRD） and drying by microwave. Characterized with X-ray diffraction （XRD） and transmission electron microscopy （TEM）, BTO spherical particles with tetragonal phase structure are well crystallized, dispersed easily and the average size was less than 10 nm.

Interstitial Oxygen Determination in Heavily Doped Silicon with "Peak-height" Method by FT-IR Spectra

Due to ineffectiveness of routine IR-absorption method for determinahon of intershtial oxygen in heavily doped silicon, a 'peak-height' method has been dcveloped. The phosphorus-doped CZ-Si with n=(7.l～l2)× 10~17cm^(-3) was taken as sample for characterization. The calculation results at 300 K and 10 K were ptesented in detail. The'peak-height' method is much simpler than 'short-baseline' and 'curved-baseline' methods.

Ag-doped ZnO nanorods synthesized by two-step method

A two-step method is adopted to synthesize Ag-doped ZnO nanorods. A ZnO seed layer is first prepared on a glass substrate by thermal decomposition of zinc acetate. Ag-doped ZnO nanorods are then assembled on the ZnO seed layer using the hydrothermal method. The influences of the molar percentage of Ag ions to Zn ions （RAg/zn） on the structural and optical properties of the ZnO nanorods obtained are carefully studied using X-ray diffractometry, scanning electron microscopy and spectrophotometry. Results indicate that Ag ions enter into the crystal lattice through the substitution of Zn ions. The （002） c-axis-preferred orientation of the ZnO nanorods decreases as RAg/Zn increases. At RAg/Zn 〉 1.0%, ZnO nanorods lose their c-axis-preferred orientation and generate Ag precipitates from the ZnO crystal lattice. The average transmissivity in the visible region first increases and then decreases as RAg/Zn increases. The absorption edge is first blue shifted and then red shifted. The influence of Ag doping on the average head face, and axial dimensions of the ZnO nanorods may be optimized to improve the average transmissivity at RAg/Zn 〈 1.0%.

Simulations of the Electron Spectrum of Quantum Wires in <i>n</i>-Si of Arbitrarily Doping Profile by Thomas-Fermi Method

Electron spectrum in doped n-Si quantum wires is calculated by the Thomas-Fermi (TF) method under finite temperatures. The many-body exchange corrections are taken into account. The doping profile is arbitrary. At the first stage, the electron potential energy is calculated from a simple two-dimensional equation. The effective iteration scheme is proposed there that is valid for multidimensional problems. Then the energy levels and wave functions of this quantum well are simulated from the Schr&#246;dinger equations. The expansion by the full set of eigenfunctions of the linear harmonic oscillator is used. The quantum mechanical perturbation theory can be utilized to compute the energy levels. Generally, the perturbation theory for degenerate energy levels should be used.

Yttrium-Doped SnO_2 Prepared by Co-Precipitation Method for Lithium-Ion Battery Anodes

SnO2 doped with Y were prepared by co-precipitation method and tested in lithium-ion cells. The structure and morphology of the materials were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). XRD patterns presented that the all the as-prepared materials had tetragonal rutile structure but a second phase (Y2O3) was observed when Y content reached 4%. TEM micrograph indicated that Y doped SnO2 had a small particle size ranging from 20 to 25 nm. The electrochemical properties for an anode active material in lithium-ion batteries were investigated at room temperature, including the observed capacity involved in the first-discharge and the reversible capacity values during subsequent charge-discharge cycles. The as-prepared Y-doped SnO2 exhibited promising electrochemical properties as anodes for lithium-ion batteries.

Preparation and Performance of Si^4＋ -doping Rod-shaped TiO2 Powder by Nonhydrolytic Sol-gel Method

Titania（TiO2） nanorod powder was prepared by nonhydrolytic sol-gel method using titanic chloride（TiCl4） as titanium source, methylene dichloride（CH2Cl2） as solvent, absolute ethyl alcohol（CH（-3）CH2OH） as oxygen donor. The effects of Si^（4＋） doping on the TiO2 nanocrystalline phase transformation temperature were systematically researched. The results showed that when the molar ratio of Ti^（4＋） to Si^（4＋） is 1 to1.3, TiO2 prepared by calcination at 1 100 ℃ for 1 hour exhibits rod shape and has good photocatalytic activity. Doping of Si^（4＋） makes glass phase core-shell structure forming on the surface of anatase crystal particles, which can inhibit crystal phase transformation and raise the transformation temperature, making TiO2 stable in anatase phase at 1 200 ℃.

Intense up-conversion emissions of yb3＋/Dy3＋ co-doped A12O3 nanopowders prepared by non-aqueous sol-gel method＊

yb3＋/Dy3＋ co-doped A1203 nanopowders have been prepared by the non-aqueous sol-gel method and their up- conversion photoluminescence spectra are measured under excitation by a 980-nm semiconductor laser. The results show that there are comparatively abundant spectra of up-conversion emissions centered at 378, 408, 527 and 543, and 663 nm, corresponding to 4C9/2→ 6H13/2, 4C9/2→ 6Hll/2, 4115/2 → 6H13/2, and 4F9/2 →6Hll/2 transitions of Dy3＋, respectively. Two-photon and three-photon processes are involved in ultraviolet, violet, green, and red up-conversion emissions. The energy transition between Yb3＋ and Dy3＋ is discussed.

Characterization and Doping Effect of Cu-Doped ZnO Films

Cu(copper)-doped ZnO(zinc oxide)was synthesized using Cu(NO3)2·3H2O(copper(II)nitrate)and Zn(NO3)2·6H2O(zinc nitrate)by chemical co-precipitation method.The weight percentages of dopant in solution were Cu(2,3,and 5 wt%).Cu-doped ZnO thin films were prepared on p-Si(100)substrate by screen printing method.Cu-doped ZnO/Si films were annealed at different temperatures from 300 to 700°C.In this study,Cu-doped ZnO structures were prepared by a simple precipitation technique,and characterized by various techniques such as XRD(X-ray diffraction)and SEM(scanning electron microscope).The electrical properties of Cu-doped ZnO/Si were measured.It has found that Cu-doped ZnO/Si films can be used as optoelectronic devices.

Structural and Optical Properties of Cu2+ + Ce3+ Co-Doped ZnO by Solution Combustion Method

In this work, ZnO, Ce3+ doped ZnO (ZnO/Ce3+) and Cu2+ + Ce3+ co-doped ZnO (ZnO/Cu2+ + Ce3+ ) solid solutions powders were synthesized by a solution combustion method maintaining the Ce3+ ion concentration constant in 3%Wt while the Cu2+ ion concentration was varied in 1, 2, 3, 10 and 20%Wt. After its synthesis, all the samples were annealed at 900?C by 24 h. The ZnO, ZnO/Ce3+ and ZnO/Cu2+ + Ce3+ powders were structurally characterized using X-ray diffraction (XRD) technique, and the XRD patterns showed that for pure ZnO, Cu2+ undoped ZnO/Ce3+ and ZnO/Ce3+ doped with the Cu2+ ion, the three samples exhibited the hexagonal wurtzite ZnO crystalline structure. However, the morphology and particle size of both samples were observed by means of a scanning electron microscopy (SEM);from SEM image, it is observed that the crystallites of both samples are agglomerated forming bigger amorphous particles with an approximate average size of 1 μm. In addition, the photoluminescence of the ZnO, Ce3+ doped ZnO and Cu2+ + Ce3+ doped ZnO samples was measurement under an illumination of 209 nm wavelength (UV region): for the ZnO/Ce3+ sample, your emission spectrum is in the visible region from blue color until red color;the UV band of the ZnO is suppressed. The multicolor emission visible is attributed to the Ce3+ ion photoluminescence, while for the ZnO/Cu2+ + Ce3+, its emission PL spectrum is quenching by the Cu2+ ion, present in the ZnO crystalline.

Structural and Electrochemical Properties of Ceria-Doped SnO_2 Prepared by Sol-Gel Method

Tin dioxide (SnO2) and Ce-doped SnO2 were successfully synthesized by sol-gel method and electrochemical properties were studied in cell with Li as counter electrode. The samples were characterized by X-ray diffraction (XRD) and Transmission electron microscopy (TEM). XRD patterns presented that a second phase (CeO) was observed when the Ce content reached 5%. TEM micrograph indicated that Ce-doped SnO2 had a small particle with mean size of 30 nm. The electrochemical properties were also characterized at room temperature, and the results demonstrated that the Ce-doped SnO2 samples exhibited promising electrochemical properties and Ce doped in as-prepared samples plays an important role.

掺氮碳量子点用于柳氮磺吡啶的快速检测

以微波法一步合成制备出荧光性能强、荧光量子产率为89.38%的掺氮碳量子点(N-CDs),并通过荧光猝灭法建立了快速准确测定柳氮磺吡啶(SSZ)的新方法。通过透射电子显微镜、傅里叶红外光谱对碳量子点进行表征,结果显示N-CDs的平均粒径为2.91 nm,主要由C、O、N元素组成,大量羰基、羟基和羧基存在于N-CDs表面。在最佳条件下,柳氮磺吡啶浓度在0.1~2μmol/L和3~200μmol/L范围内线性良好,检出限为0.2μmol/L。将所建方法用于柳氮磺吡啶肠溶片中柳氮磺吡啶含量的测定,回收率为97.3%~102%。