High‑Entropy Layered Oxide Cathode Enabling High‑Rate for Solid‑State Sodium‑Ion Batteries

Na-ion O3-type layered oxides are prospective cathodes for Na-ion batteries due to high energy density and low-cost.Nevertheless,such cathodes usually suffer from phase transitions,sluggish kinetics and air instability,making it difficult to achieve high performance solid-state sodium-ion batteries.Herein,the high-entropy design and Li doping strategy alleviate lattice stress and enhance ionic conductivity,achieving high-rate performance,air stability and electrochemically thermal stability for Na_(0.95)Li_(0.06)Ni_(0.25)Cu_(0.05)Fe_(0.15)Mn_(0.49)O_(2).This cathode delivers a high reversible capacity(141 mAh g^(−1)at 0.2C),excellent rate capability(111 mAh g^(−1)at 8C,85 mAh g^(−1)even at 20C),and long-term stability(over 85%capacity retention after 1000 cycles),which is attributed to a rapid and reversible O3–P3 phase transition in regions of low voltage and suppresses phase transition.Moreover,the compound remains unchanged over seven days and keeps thermal stability until 279℃.Remarkably,the polymer solid-state sodium battery assembled by this cathode provides a capacity of 92 mAh g^(−1)at 5C and keeps retention of 96%after 400 cycles.This strategy inspires more rational designs and could be applied to a series of O3 cathodes to improve the performance of solid-state Na-ion batteries.

Phase engineering of Ni-Mn binary layered oxide cathodes for sodiumion batteries

Nickel-manganese binary layered oxides with high working potential and low cost are potential candidates for sodium-ion batteries,but their electrochemical properties are highly related to compositional diversity.Diverse composite materials with various phase structures of P3,P2/P3,P2,P2/O3,and P2/P3/O3 were synthesized by manipulating the sodium content and calcination conditions,leading to the construction of a synthetic phase diagram for Na_(x)Ni_(0.25)Mn_(0.75)O_(2)(0.45≤x≤1.1).Then,we compared the electrochemical characteristics and structural evolution during the desodiation/sodiation process of P2,P2/P3,P2/03,and P2/P3/O3-Na_(x)Ni_(0.25)Mn_(0.75)O_(2).Among them,P2/P3-Na0.75Ni0.25Mn0.75O2exhibits the best rate capability of 90.9 mA h g^(-1)at 5 C,with an initial discharge capacity of 142.62 mA h g^(-1)at 0.1 C and a capacity retention rate of 78.25%after 100 cycles at 1 C in the voltage range of 2-4.3 V.The observed superior sodium storage performance of P2/P3 hybrids compared to other composite phases can be attributed to the enhanced Na^(+)transfer dynamic,reduction of the Jahn-teller effect,and improved reaction reversibility induced by the synergistic effect of P2 and P3 phases.The systematic research and exploration of phases in Na_(x)Ni_(0.25)Mn_(0.75)O_(2)provide new sights into high-performance nickel-manganese binary layered oxide for sodium-ion batteries.

Mg/Fe site-specific dual-doping to boost the performance of cobalt-free nickle-rich layered oxide cathode for high-energy lithium-ion batteries

Layer-type LiNi0.9Mn0.1O2is promising to be the primary cathode material for lithium-ion batteries(LIBs)due to its excellent electrochemical performance.Unfortunately,the cathode with high nickel content suffers from severely detrimental structural transformation that causes rapid capacity attenuation.Herein,site-specific dual-doping with Fe and Mg ions is proposed to enhance the structural stability of LiNi0.9Mn0.1O2.The Fe3+dopants are inserted into transition metal sites(3b)and can favorably provide additional redox potential to compensate for charge and enhance the reversibility of anionic redox.The Mg ions are doped into the Li sites(3a)and serve as O_(2)^(-)-Mg^(2+)-O_(2)^(-)pillar to reinforce the electrostatic cohesion between the two adjacent transition-metal layers,which further suppress the cracking and the generation of harmful phase transitions,ultimately improving the cyclability.The theoretical calculations,including Bader charge and crystal orbital Hamilton populations(COHP)analyses,confirm that the doped Fe and Mg can form stable bonds with oxygen and the electrostatic repulsion of O_(2)^(-)-O_(2)^(-)can be effectively suppressed,which effectively mitigates oxygen anion loss at the high delithiation state.This dual-site doping strategy offers new avenues for understanding and regulating the crystalline oxygen redox and demonstrates significant potential for designing high-performance cobalt-free nickel-rich cathodes.

Cationic ordering transition in oxygen-redox layered oxide cathodes

Understanding the structural origin of the competition between oxygen 2p and transition-metal 3d orbitals in oxygen-redox(OR)layered oxides is eminently desirable for exploring reversible and high-energy-density Li/Na-ion cathodes.Here,we reveal the correlation between cationic ordering transition and OR degradation in ribbon-ordered P3-Na_(0.6)Li_(0.2)Mn_(0.8)O_(2) via in situ structural analysis.Comparing two different voltage windows,the OR capacity can be improved approximately twofold when suppressing the in-plane cationic ordering transition.We find that the intralayer cationic migration is promoted by electrochemical reduction from Mn^(4+)to Jahn–Teller Mn^(3+)and the concomitant NaO_(6) stacking transformation from triangular prisms to octahedra,resulting in the loss of ribbon ordering and electrochemical decay.First-principles calculations reveal that Mn^(4+)/Mn^(3+)charge ordering and alignment of the degenerate eg orbital induce lattice-level collective Jahn–Teller distortion,which favors intralayer Mn-ion migration and thereby accelerates OR degradation.These findings unravel the relationship between in-plane cationic ordering and OR reversibility and highlight the importance of superstructure protection for the rational design of reversible OR-active layered oxide cathodes.

Recent progress in Ni-rich layered oxides and related cathode materials for Li-ion cells

Undoubtedly,the enormous progress observed in recent years in the Ni-rich layered cathode materials has been crucial in terms of pushing boundaries of the Li-ion battery(LIB)technology.The achieved improvements in the energy density,cyclability,charging speed,reduced costs,as well as safety and stability,already contribute to the wider adoption of LIBs,which extends nowadays beyond mobile electronics,power tools,and electric vehicles,to the new range of applications,including grid storage solutions.With numerous published papers and broad reviews already available on the subject of Ni-rich oxides,this review focuses more on the most recent progress and new ideas presented in the literature references.The covered topics include doping and composition optimization,advanced coating,concentration gradient and single crystal materials,as well as innovations concerning new electrolytes and their modification,with the application of Ni-rich cathodes in solid-state batteries also discussed.Related cathode materials are briefly mentioned,with the high-entropy approach and zero-strain concept presented as well.A critical overview of the still unresolved issues is given,with perspectives on the further directions of studies and the expected gains provided.

Unexpected Li displacement and suppressed phase transition enabling highly stabilized oxygen redox in P3-type Na layered oxide cathode

Oxygen redox is considered a new paradigm for increasing the practical capacity and energy density of the layered oxide cathodes for Na-ion batteries. However, severe local structural changes and phase transitions during anionic redox reactions lead to poor electrochemical performance with sluggish kinetics.Here, we propose a synergy of Li-Cu cations in harnessing the full potential of oxygen redox, through Li displacement and suppressed phase transition in P3-type layered oxide cathode. P3-type Na_(0.7)[Li_(0.1)Cu_(0.2)Mn_(0.7)]O_(2) cathode delivers a large specific capacity of ~212 mA h g^(-1)at 15 mA g^(-1). The discharge capacity is maintained up to ~90% of the initial capacity after 100 cycles, with stable occurrence of the oxygen redox in the high-voltage region. Through advanced experimental analyses and first-principles calculations, it is confirmed that a stepwise redox reaction based on Cu and O ions occurs for the charge-compensation mechanism upon charging. Based on a concrete understanding of the reaction mechanism, the Li displacement by the synergy of Li-Cu cations plays a crucial role in suppressing the structural change of the P3-type layered material under the oxygen redox reaction, and it is expected to be an effective strategy for stabilizing the oxygen redox in the layered oxides of Na-ion batteries.

Impact of Transition Metal Layer Vacancy on the Structure and Performance of P2 Type Layered Sodium Cathode Material

This study explores the impact of introducing vacancy in the transition metal layer of rationally designed Na_(0.6)[Ni_(0.3)Ru_(0.3)Mn_(0.4)]O_(2)(NRM)cathode material.The incorporation of Ru,Ni,and vacancy enhances the structural stability during extensive cycling,increases the operation voltage,and induces a capacity increase while also activating oxygen redox,respectively,in Na_(0.7)[Ni_(0.2)V_(Ni0.1)Ru_(0.3)Mn_(0.4)]O_(2)(V-NRM)compound.Various analytical techniques including transmission electron microscopy,X-ray absorption near edge spectroscopy,operando X-ray diffraction,and operando differential electrochemical mass spectrometry are employed to assess changes in the average oxidation states and structural distortions.The results demonstrate that V-NRM exhibits higher capacity than NRM and maintains a moderate capacity retention of 81%after 100 cycles.Furthermore,the formation of additional lone-pair electrons in the O 2p orbital enables V-NRM to utilize more capacity from the oxygen redox validated by density functional calculation,leading to a widened dominance of the OP4 phase without releasing O_(2) gas.These findings offer valuable insights for the design of advanced high-capacity cathode materials with improved performance and sustainability in sodium-ion batteries.

Facet-dependent Thermal and Electrochemical Degradation of Lithium-rich Layered Oxides

Lithium-rich layered oxides(LLOs)are promising candidate cathode materials for safe and inexpensive high-energy-density Li-ion batteries.However,oxygen dimers are formed from the cathode material through oxygen redox activity,which can result in morphological changes and structural transitions that cause performance deterioration and safety concerns.Herein,a flake-like LLO is prepared and aberration-corrected scanning transmission electron microscopy(STEM),in situ high-temperature X-ray diffraction(HT-XRD),and soft X-ray absorption spectrum(sXAS)are used to explore its crystal facet degradation behavior in terms of both thermal and electrochemical processes.Void-induced degradation behavior of LLO in different facet reveals significant anisotropy at high voltage.Particle degradation originates from side facets,such as the(010)facet,while the close(003)facet is stable.These results are further understood through ab initio molecular dynamics calculations,which show that oxygen atoms are lost from the{010}facets.Therefore,the facet degradation process is that oxygen molecular formed in the interlayer and accumulated in the ab plane during heating,which result in crevice-voids in the ab plane facets.The study reveals important aspects of the mechanism responsible for oxygen-anionic activity-based degradation of LLO cathode materials used in lithium-ion batteries.In particular,this study provides insight that enables precise and efficient measures to be taken to improve the thermal and electrochemical stability of an LLO.

Recent progress in synthesis and surface modification of nickel-rich layered oxide cathode materials for lithium-ion batteries

Nickel-rich layered oxides have been identified as the most promising commercial cathode materials for lithium-ion batteries(LIBs)for their high theoretical specific capacity.However,the poor cycling stability of nickel-rich cathode materials is one of the major barriers for the large-scale usage of LIBs.The existing obstructions that suppress the capacity degradation of nickel-rich cathode materials are as a result of phase transition,mechanical instability,intergranular cracks,side reaction,oxygen loss,and thermal instability during cycling.Core–shell structures,oxidating precursors,electrolyte additives,doping/coating and synthesizing single crystals have been identified as effective methods to improve cycling stability of nickel-rich cathode materials.Herein,recent progress of surface modification,e.g.coating and doping,in nickel-rich cathode materials are summarized based on Periodic table to provide a clear understanding.Electrochemical performances and mechanisms of modified structure are discussed in detail.It is hoped that an overview of synthesis and surface modification can be presented and a perspective of nickel-rich materials in LIBs can be given.

Recent progress on electrolyte functional additives for protection of nickel-rich layered oxide cathode materials

In advantages of their high capacity and high operating voltage,the nickel(Ni)-rich layered transition metal oxide cathode materials(LiNi_(x)Co_(y)Mn_(z)O_(2)(NCMxyz,x+y+z=1,x≥0.5)and LiNi_(0.8)Co_(0.15)Al_(0.05)O_(2)(NCA))have been arousing great interests to improve the energy density of LIBs.However,these Nirich cathodes always suffer from rapid capacity degradation induced by unstable cathode-electrolyte interphase(CEI)layer and destruction of bulk crystal structure.Therefore,varied electrode/electrolyte interface engineering strategies(such as electrolyte formulation,material coating or doping)have been developed for Ni-rich cathodes protection.Among them,developing electrolyte functional additives has been proven to be a simple,effective,and economic method to improve the cycling stability of Nirich cathodes.This is achieved by removing unfavorable species(such as HF,H_(2)O)or constructing a stable and protective CEI layer against unfavorable reactive species(such as HF,H_(2)O).Herein,this review mainly introduces the varied classes of electrolyte functional additives and their working mechanism for interfacial engineering of Ni-rich cathodes.Especially,key favorable species for stabilizing CEI layer are summarized.More importantly,we put forward perspectives for screening and customizing ideal functional additives for high performance Ni-rich cathodes based LIBs.

In/ex-situ Raman spectra combined with EIS for observing interface reactions between Ni-rich layered oxide cathode and sulfide electrolyte

The interfacial instability between Ni-rich layered oxide cathodes and sulfide electrolytes is a serious problem,leading to poor electrochemical properties of all-solid-state lithium batteries(ASSLB).The chemical/electrochemical side reactions are considered to be the origin of the interfacial deterioration.However,the influence of chemical and electrochemical side reactions on the interfacial deterioration is rarely studied specifically.In this work,the deterioration mechanism of the interface between LiNi0.85-xCo0.15AlxO2 and Li10GeP2S12 is investigated in detail by combining in/ex-situ Raman spectra and Electrochemical Impedance Spectroscopy(EIS).It can be determined that chemical side reaction between LiNi0.8Co0.15Al0.05O2 and Li10GeP2S12 will occur immediately once contacted,and the interfacial deterioration becomes more serious after charge-discharge process under the dual effects of chemical and electrochemical side reactions.Moreover,our research reveals that the interfacial stability and the cycle performance of ASSLB can be greatly enhanced by increasing Al-substitution for Ni in LiNi0.85-xCo0.15AlxO2.In particular,the capacity retention of LiNi0.6Co0.15Al0.25O2 cathode after 200 cycles can reach 81.9%,much higher than that of LiNi0.8Co0.15Al0.05O2 cathode(12.5%@200 cycles).This work gives an insight to study the interfacial issues between Ni-rich layered oxide cathode and sulfide electrolyte for ASSLBs.

Recent progress in Li and Mn rich layered oxide cathodes for Li-ion batteries

Li and Mn rich(LMR)layered oxides,written as xLi_(2) MnO_(3)·(1-x)LiMO_(2)(M=Mn,Ni,Co,Fe,etc.),have been widely reported in recent years due to their high capacity and high energy density.The stable structure and superior performance of LMR oxides make them one of the most promising candidates for the next-generation cathode materials.However,the commercialization of these materials is hindered by several drawbacks,such as low initial Coulombic efficiency,the degradation of voltage and capacity during cycling,and poor rate performance.This review summarizes research progress in solving these concerns of LMR cathodes over the past decade by following three classes of strategies:morphology design,bulk design,and surface modification.We elaborate on the processing procedures,electrochemical performance,mechanisms,and limitations of each approach,and finally put forward the concerns left and the possible solutions for the commercialization of LMR cathodes.

Addressing cation mixing in layered structured cathodes for lithium-ion batteries:A critical review

High-performance lithium-ion batteries(LIB)are important in powering emerging technologies.Cathodes are regarded as the bottleneck of increasing battery energy density,among which layered oxides are the most promising candidates for LIB.However,a limitation with layered oxides cathodes is the transition metal and Li site mixing,which significantly impacts battery capacity and cycling stability.Despite recent research on Li/Ni mixing,there is a lack of comprehensive understanding of the origin of cation mixing between the transition metal and Li;therefore,practical means to address it.Here,a critical review of cation mixing in layered cathodes has been provided,emphasising the understanding of cation mixing mechanisms and their impact on cathode material design.We list and compare advanced characterisation techniques to detect cation mixing in the material structure;examine methods to regulate the degree of cation mixing in layered oxides to boost battery capacity and cycling performance,and critically assess how these can be applied practically.An appraisal of future research directions,including superexchange interaction to stabilise structures and boost capacity retention has also been concluded.Findings will be of immediate benefit in the design of layered cathodes for high-performance rechargeable LIB and,therefore,of interest to researchers and manufacturers.

Clarification of underneath capacity loss for O3-type Ni, co free layered cathodes at high voltage for sodium ion batteries

Earth abundant O3-type NaFe_(0.5)Mn_(0.5)O_(2)layered oxide is regarded as one of the most promising cathodes for sodium ion batteries due to its low cost and high energy density.However,its poor structural stability and cycle life strongly impede the practical application.Herein,the dynamic phase evolution as well as charge compensation mechanism of O3-type NaFe_(0.5)Mn_(0.5)O_(2)cathode during sodiation/desodiation are revealed by a systemic study with operando X-ray diffraction and X-ray absorption spectroscopy,high resolution neutron powder diffraction and neutron pair distribution functions.The layered structure experiences a phase transition of O3→P3→OP2→ramsdellite during the desodiation,and a new O3’phase is observed at the end of the discharge state(1.5 V).The density functional theory(DFT)calculations and nPDF results suggest that depletion of Na^(+)ions induces the movement of Fe into Na layer resulting the formation of an inert ramsdellite phase thus causing the loss of capacity and structural integrity.Meanwhile,the operando XAS clarified the voltage regions for active Mn^(3+)/Mn^(4+)and Fe^(3+)/Fe^(4+)redox couples.This work points out the universal underneath problem for Fe-based layered oxide cathodes when cycled at high voltage and highlights the importance to suppress Fe migration regarding the design of high energy O3-type cathodes for sodium ion batteries.

Mg-doped layered oxide cathode for Na-ion batteries

Na-ion batteries(NIBs)are regarding as the optimum complement for Li-ion batteries along with the rapid development of stationary energy storage systems.In order to meet the commercial demands of cathodes for NIBs,O3-type Cu containing layered oxide Na_(0.9)0Cu_(0.22)Fe_(0.30)Mn_(0.48O_(2))with good comprehensive performance and low-cost element components is very promising for the practical use.However,only part of the Cu^(3+)/Cu^(2+)redox couple participated in the redox reaction,thus impairing the specific capacity of the cathode materials.Herein,Mg2+-doped O3-Na0.90Mg0.08Cu0.22Fe0.30Mn0.40O_(2)layered oxide without Mn3+was synthesized successfully,which exhibited improved reversible specific capacity of 118 mAh/g in the voltage range of 2.4-4.0 V at 0.2 C,corresponding to the intercalation/deintercalation of 0.47 Na+(0.1 more than that of Na_(0.9)0Cu_(0.22)Fe_(0.30)Mn_(0.48O_(2))).This work demonstrates an important strategy to obtain advanced layered oxide cathodes for NIBs.

A dynamic infiltration technique to synthesize nanolayered cathodes for high performance and robust solid oxide fuel cells

Solution infiltration is a popular technique for the surface modification of solid oxide fuel cell(SOFC)cathodes.However,the synthesis of nanostructured SOFC cathodes by infiltration is a tedious process that often requires several infiltration and high temperature(≥500℃)calcination cycles.Moreover,fabricating large-area nanostructured cathodes via infiltration still requires serious attention.Here,we propose a facile and scalable urea assisted ultrasonic spray infiltration technique for nanofabrication of SOFC cathodes.It is demonstrated that by using urea as a precipitating agent,the calcination after each infiltration cycle can be omitted and the next infiltration can be performed just after a drying step(≤100℃).Finally,the precipitates can be converted into a desired catalyst phase in single calcination thus,a nanostructured cathode can be fabricated in a much faster manner.It is also shown that the low calcination temperature of the cathode(≤900℃)can produce highly durable SOFC performance even without employing a Ce_(0.9)Gd_(0.1)O_(2)(GDC)diffusion barrier layer which provides the ease of SOFC fabrication.While coupling with an ultrasonic spray technique,the urea assisted infiltration can be scaled up for any desired cathode area.La_(0.6)Sr_(0.4)Co_(0.2)Fe_(0.8)O_(3) nanolayered cathode was fabricated and it was characterized by scanning electron microscope(SEM),X-ray diffraction(XRD),and transmission electron microscopy(TEM)techniques.SEM showed the formation of a nanolayer cathode just after 5 cycles of the urea assisted infiltration while the XRD and TEM confirmed the phase and stoichiometric uniformity of the 100 nm cathode nanolayer.The effectiveness of the newly developed technique was further verified by the stable operation of a GDC buffer layer free SOFC having an active cathode area of 25 cm^(2) during a 1200 h durability test.The research outcomes propose urea assisted ultrasonic spray infiltration as a facile,scalable,and commercially viable method for the fabrication of durable nanostructured SOFC cathodes.

Phase Transformation of Lithium-rich Oxide Cathode in Full Cell and its Suppression by Solid Electrolyte Interphase on Graphite Anode

Lithium-rich oxide is one of the most promising cathodes that meet high energy density requirement for batteries of the future, but its phase transformation from layer to spinel structure caused by the lattice instability presents severe challenge to cycling stability and the actually accessible capacity. The currently available approaches to suppress this undesired irreversible process often resort to limit the high voltages that lithium-rich oxide is exposed to. However, cycling stability thus improved is at the expense of the eventual energy output. In this work, we identified a new mechanism that is directly responsible for the lithium-rich oxide phase transformation and established a clear correlation between the successive consumption of Li+on anode due to incessant interphase repairing and the over-delithiation of lithium-rich oxide cathode. This new mechanism enables a simple but effective solution to the cathode degradation, in which an electrolyte additive is used to build a dense and protective interphase on anode with the intention to minimize Li depletion at cathode. The application of this new interphase effectively suppresses both electrolyte decomposition at anode and the phase transformation of lithium-rich oxide cathode, leading to high capacity and cycling stability.

Layered oxide cathodes for sodium-ion batteries:microstructure design,local chemistry and structural unit

Because of the low price and abundant reserves of sodium compared with lithium,the research of sodium-ion batteries(SIBs)in the field of large-scale energy storage has returned to the research spotlight.Layered oxides distinguish themselves from the mains cathode materials of SIBs owing to their advantages such as high specific capacity,simple synthesis route,and environmental benignity.However,the commercial development of the layered oxides is limited by sluggish kinetics,complex phase transition and poor air stability.Based on the research ideas from macro-to micro-scale,this review systematically summarizes the current optimization strategies of sodium-ion layered oxide cathodes(SLOC)from different dimensions:microstructure design,local chemistry regulation and structural unit construction.In the dimension of microstructure design,the various structures such as the microspheres,nanoplates,nanowires and exposed active facets are prepared to improve the slow kinetics and electrochemical performance.Besides,from the view of local chemistry regulation by chemical element substitution,the intrinsic electron/ion properties of SLOC have been enhanced to strengthen the structural stability.Furthermore,the optimization idea of endeavors to regulate the physical and chemical properties of cathode materials essentially is put forward from the dimension of structural unit construction.The opinions and strategies proposed in this review will provide some inspirations for the design of new SLOC in the future.

A Facile Li_(2)TiO_(3) Surface Modification to Improve the Structure Stability and Electrochemical Performance of Full Concentration Gradient Li-Rich Oxides

Full concentration gradient lithium-rich layered oxides are catching lots of interest as the next generation cathode for lithium-ion batteries due to their high discharge voltage,reduced voltage decay and enhanced rate performance,whereas the high lithium residues on its surface impairs the structure stability and long-term cycle performance.Herein,a facile multifunctional surface modification method is implemented to eliminate surface lithium residues of full concentration gradient lithium-rich layered oxides by a wet chemistry reaction with tetrabutyl titanate and the post-annealing process.It realizes not only a stable Li_(2)TiO_(3)coating layer with 3D diffusion channels for fast Li^(+)ions transfer,but also dopes partial Ti^(4+)ions into the sub-surface region of full concentration gradient lithium-rich layered oxides to further strengthen its crystal structure.Consequently,the modified full concentration gradient lithium-rich layered oxides exhibit improved structure stability,elevated thermal stability with decomposition temperature from 289.57℃to 321.72℃,and enhanced cycle performance(205.1 mAh g^(-1)after 150 cycles)with slowed voltage drop(1.67 mV per cycle).This work proposes a facile and integrated modification method to enhance the comprehensive performance of full concentration gradient lithium-rich layered oxides,which can facilitate its practical application for developing higher energy density lithium-ion batteries.

Enhancing Na^(+) diffusion dynamics and structural stability of O3-NaMn_(0.5)Ni_(0.5)O_(2)cathode by Sc and Zn dual-substitution

Sc and Zn were introduced into O3-NaMn_(0.5)Ni_(0.5)O_(2)(NaMN)using the combination of solution combustion and solid-state method.The effect of Sc and Zn dual-substitution on Na^(+) diffusion dynamics and structural stability of NaMN was investigated.The physicochemical characterizations suggest that the introduction of Sc and Zn broaden Na^(+) diffusion channels and weaken the Na—O bonds,thereby facilitating the diffusion of sodium ions.Simulations indicate that the Sc and Zn dual-substitution decreases the diffusion barrier of Na-ions and improves the conductivity of the material.The dual-substituted NaMn_(0.5)Ni_(0.4)Sc_(0.04)Zn_(0.04)O_(2)(Na MNSZ44)cathode delivers impressive cycle stability with capacity retention of 71.2%after 200 cycles at 1C and 54.8%after 400 cycles at 5C.Additionally,the full cell paired with hard carbon anode exhibits a remarkable long-term cycling stability,showing capacity retention of 64.1%after 250 cycles at 1C.These results demonstrate that Sc and Zn dual-substitution is an effective strategy to improve the Na^(+) diffusion dynamics and structural stability of NaMN.