Collapse Behavior of Pipe-Framed Greenhouses with and without Reinforcement under Snow Loading:A 3-D Finite Element Analysis

The present paper first investigates the collapse behavior of a conventional pipe-framed greenhouse under snow loading based on a 3-D finite element analysis,in which both geometrical and material non-linearities are considered.Three snow load distribution patterns related to the wind-driven snow particle movement are used in the analysis.It is found that snow load distribution affects the deformation and collapse behavior of the pipe-framed greenhouse significantly.The results obtained in this study are consistent with the actual damage observed.Next,discussion is made of the effects of reinforcements by adding members to the basic frame on the strength of the whole structure,in which seven kinds of reinforcement methods are examined.A buckling analysis is also carried out.The results indicate that the most effective reinforcement method depends on the snow load distribution pattern.

A multiscale 3D finite element analysis of fluid/solute transport in mechanically loaded bone

The transport of fluid, nutrients, and signaling molecules in the bone lacunar-canalicular system （LCS） is critical for osteocyte survival and function. We have applied the fluorescence recovery after photobleaching （FRAP） approach to quantify load-induced fluid and solute transport in the LCS in situ, but the measurements were limited to cortical regions 30-50 μm underneath the periosteum due to the constrains of laser penetration. With this work, we aimed to expand our understanding of load-induced fluid and solute transport in both trabecular and cortical bone using a multiscaled image-based finite element analysis （FEA） approach. An intact murine tibia was first re-constructed from microCT images into a three-dimensional （3D） linear elastic FEA model, and the matrix deformations at various locations were calculated under axial loading. A segment of the above 3D model was then imported to the biphasic poroelasticity analysis platform （FEBio） to predict load-induced fluid pressure fields, and interstitial solute/fluid flows through LCS in both cortical and trabecular regions. Further, secondary flow effects such as the shear stress and/or drag force acting on osteocytes, the presumed mechano-sensors in bone, were derived using the previously developed ultrastructural model of Brinkman flow in the canaliculi. The material properties assumed in the FEA models were validated against previously obtained strain and FRAP transport data measured on the cortical cortex. Our results demonstrated the feasibility of this computational approach in estimating the fluid flux in the LCS and the cellular stimulation forces （shear and drag forces） for osteocytes in any cortical and trabecular bone locations, allowing further studies of how the activation of osteocytes correlates with in vivo functional bone formation. The study provides a promising platform to reveal potential cellular mechanisms underlying the anabolic power of exercises and physical activities in treating patients with skeletal deficiencies.

The finite element analysis of articular cartilage fiber-reinforced composite model under rolling load

Articular cartilage is a layer of low-friction,load-bearing soft hydrated tissue covering bone-ends in diarthrosis,which plays an important role in spreading the load,reducing the joint contact stress,joint friction and wear during exercise.The vital mechanical function

3D Finite Element Analysis of a Man Hip Joint Femur under Impact Loads

Objective： The biomechanical characters of the bone fracture of the man femoral hip joint under impact loads are explored. Methods ：A biosystem model of the man femoral hip joint by using the GE （ General Electric） lightspeed multi-lay spiral CT is conducted. A 3D finite element model is established by employing the finite element software ANSYS. The FE analysis mainly concentrates on the effects of the impact directions arising from intense movements and the parenchyma on the femoral hip joint on the stress distributions of the proximal femur. Results：The parenchyma on the hip joint has relatively large relaxation effect on the impact loads. Conclusion：Effects of the angle δ of the impact load to the anterior direction and the angle γ of the impact load to the femur shaft on the bone fracture are given;δ has larger effect on the stress and strain distributions than the angle γ,which mainly represents the fracture of the upper femur including the femoral neck fracture when the posterolateral femur is impacted, consistent with the clinical resuits.

Three-dimensional Finite Element Analysis of the Mechanical Properties of Helical Thread Connection

Conventional analytical and numerical methods for the mechanical properties of helical threads are relied on many assumptions and approximations and thus hardly yield satisfied results. A parameterized 3D finite element model of bolted joints with real helical thread geometry is established and meshed with refined hexahedral elements. The Von Mises plasticity criterion, kinematic hardening rule of materials and interfacial contacts are employed to make it possible for the suggested model be able to approach real assembly conditions. Then, the mechanical properties of bolted joints with different thread pitches, thread numbers and modular ratios are investigated, including the contact pressure distribution at joint interfaces, the axial load distribution and stress concentration in screw threads during the loading and unloading process. Simulation results indicate that the load distribution in screw threads produced by the suggested model agrees well the results from CHEN’s photoelastic tests. In addition, an interesting phenomenon is found that tightening the bolt with a large preload first and then adjusting the clamping force by unloading can make the load distribution more uniform and reduce the maximum residual equivalent stress in thread roots by up to 40%. This research provides a simple and practical approach to constructing the 3D finite element model and predicting the mechanical properties of helical thread connection.

Finite Element Analysis for the Structure Optimization Design of the CPUE Load-Bearing Wheel of Tracked Vehicle

A new kind of material cast polyurethane elastomers (CPUE) is introduced to take the place of rubber on load bearing wheel for the first time. Based on load bearing wheel dimensions, material properties and operating conditions, the structure of wheel flange is optimized by zero order finite element method. A detailed three dimensional finite element model of flange of load bearing wheel is developed and utilized to optimize structure of wheel flange. Its service life, which is affected by flange structure parameter, is analyzed by comparing the optimization results with those of prototype of wheel. The results of optimization are presented and the stress field of load bearing wheel in optimal dimension obtained by using finite element analysis method is demonstrated. The finite element analysis and optimization results show that the CPUE load bearing wheel is feasible and suitable for the tracked vehicle and has a guiding value in practice of the weighting design of the whole tracked vehicle.

THEORY OF PERTURBATION FINITE ELEMENT ANALYSIS FOR SOLUTION OF NONLINEAR BUCKLING CRITICAL LOADS OF STRUCTURES

The author presents a theory, including the complete analysis and incomplete analysis,of perturbational finite element analysis for the solution of nonlinear buckling critical loadsof structures.

Finite Element Analysis on the Pre-load Structures of the Central Solenoid for the HT-7U Device

The central solenoid is an important part of the HT-7U device. In this paper， the computational analysis of the stress and the displacement on the pre-load structures of the central solenoid have been made by the finite element analysis system COSMOS/M2.0 under room and/or operating temperature. According to the analytical results, the clip aprons and compression plates are all satisfied with safety design criteria.

Finite element failure analysis of continuous prestressed concrete box girders

In order to analyze the load carrying capacity of prestressed concrete box girders, failure behaviors of in-situ deteriorated continuous prestressed concrete box girders under loading are experimentally observed and a finite failure analysis method for predicting behaviors of box girders is developed. A degenerated solid shell element is used to simulate box girders and material nonlinearity is considered. Since pre-stressed concrete box girders usually have a large number of curve prestressed tendons, a type of combined element is presented to simulate the prestressed tendons of box girders, and then the number of elements can be significantly reduced. The analytical results are compared with full-scale failure test results. The comparison shows that the presented method can be effectively applied to the failure analysis of in-situ continuous prestressed concrete box girders, and it also shows that the studied old bridge still has enough load carrying capacity.

Strength reduction and step-loading finite element approaches in geotechnical engineering

The finite element limit analysis method has the advantages of both numerical and traditional limit equilibrium techniques and it is particularly useful to geotechnical engineering.This method has been developed in China,following well-accepted international procedures,to enhance understanding of stability issues in a number of geotechnical settings.Great advancements have been made in basic theory,the improvement of computational precision,and the broadening of practical applications.This paper presents the results of research on（1） the efficient design of embedded anti-slide piles,（2） the stability analysis of reservoir slopes with strength reduction theory,and（3） the determination of the ultimate bearing capacity of foundations using step-loading FEM（overloading）.These three applications are evidence of the design improvements and benefits made possible in geotechnical engineering by finite element modeling.

Finite element analysis of γ'-phase raft mechanism in Ni-based single crystal superalloy

The finite element method was applied to study the mechanics of rafting ofγ' precipitates in a single crystal Ni-based superalloy with the [001] orientation. The results show that the creep and rafting are closely related with the stress and strain energy density distributions in the matrix channels. The application of an external stress leads to differential levels of von Mises stress and strain energy density, and the largest value of the stress appears at the corners of the matrix near the interface. Creep dislocations penetrate preferentially into the most highly stressed matrix channels where theγ'-phase rafting is also enlarged. Meanwhile, the von Mises stress ofγmatrix andγ' precipitate increases with the increase of temperature, thus the rafting becomes easier at a higher temperature. Moreover, according to the analysis of slip systems for the Ni-based superalloy, the critical external load for bowing a dislocation through a matrix channel at 950℃is about 180 MPa, which is consistent with the related experimental results.

Analysis of Force Transmission by a Knee Loading Device from Skin and Soft Tissue to Knee Joint Elements

Dynamic loading to a knee joint is considered to be an effective modality for enhancing the healing of long bones and cartilage that are subject to ailments like fractures, osteoarthritis, etc. We developed a knee loading device and tested it for force application. The device applies forces on the skin, whereas force transmitted to the knee joint elements is directly responsible for promoting the healing of bone and cartilage. However, it is not well understood how loads on the skin are transmitted to the cartilage, ligaments, and bone. Based on a CAD model of a human knee joint, we conducted a finite element analysis (FEA) for force transmission from the skin and soft tissue to a knee joint. In this study, 3D models of human knee joint elements were assembled in an FEA software package (SIMSOLID). A wide range of forces was applied to the skin with different thickness in order to obtain approximate force values transmitted from the skin to the joint elements. The maximum Von Mises stress and displacement distributions were estimated for different components of the knee joint. The results demonstrate that the high load bearing areas were located on the posterior portion of the cartilage. This prediction can be used to improve the design of the knee loading device.

Assessment of natural frequency of installed offshore wind turbines using nonlinear finite element model considering soil-monopile interaction

A nonlinear finite element model is developed to examine the lateral behaviors of monopiles, which support offshore wind turbines(OWTs) chosen from five different offshore wind farms in Europe. The simulation is using this model to accurately estimate the natural frequency of these slender structures, as a function of the interaction of the foundations with the subsoil. After a brief introduction to the wind power energy as a reliable alternative in comparison to fossil fuel, the paper focuses on concept of natural frequency as a primary indicator in designing the foundations of OWTs. Then the range of natural frequencies is provided for a safe design purpose. Next, an analytical expression of an OWT natural frequency is presented as a function of soil-monopile interaction through monopile head springs characterized by lateral stiffness KL, rotational stiffness KRand cross-coupling stiffness KLRof which the differences are discussed. The nonlinear pseudo three-dimensional finite element vertical slices model has been used to analyze the lateral behaviors of monopiles supporting the OWTs of different wind farm sites considered. Through the monopiles head movements(displacements and rotations), the values of KL, KRand KLRwere obtained and substituted in the analytical expression of natural frequency for comparison. The comparison results between computed and measured natural frequencies showed an excellent agreement for most cases. This confirms the convenience of the finite element model used for the accurate estimation of the monopile head stiffness.

Slope stability analysis under seismic load by vector sum analysis method

The vibration characteristics and dynamic responses of rock and soil under seismic load can be estimated with dynamic finite element method （DFEM）. Combining with the DFEM, the vector sum analysis method （VSAM） is employed in seismic stability analysis of a slope in this paper. Different from other conventional methods, the VSAM is proposed based on the vector characteristic of force and current stress state of the slope. The dynamic stress state of the slope at any moment under seismic load can he obtained by the DFEM, thus the factor of safety of the slope at any moment during earthquake can be easily obtained with the VSAM in consideration of the DFEM. Then, the global stability of the slope can be estimated on the basis of time-history curve of factor of safety and reliability theory. The VSAM is applied to a homogeneous slope under seismic load. The factor of safety of the slope is 1.30 under gravity only and the dynamic factor of safety under seismic load is 1.21. The calculating results show that the dynamic characteristics and stability state of the slope with input ground motion can be actually analyzed. It is believed that the VSAM is a feasible and practical approach to estimate the dynamic stability of slopes under seismic load.

Calculations of plastic collapse load of pressure vessel using FEA

This paper proposes a theoretical method using finite element analysis(FEA) to calculate the plastic collapse loads of pressure vessels under internal pressure,and compares the analytical methods according to three criteria stated in the ASME Boiler Pressure Vessel Code. First,a finite element technique using the arc-length algorithm and the restart analysis is developed to conduct the plastic collapse analysis of vessels,which includes the material and geometry non-linear properties of vessels. Second,as the mechanical properties of vessels are assumed to be elastic-perfectly plastic,the limit load analysis is performed by em-ploying the Newton-Raphson algorithm,while the limit pressure of vessels is obtained by the twice-elastic-slope method and the tangent intersection method respectively to avoid excessive deformation. Finally,the elastic stress analysis under working pressure is conducted and the stress strength of vessels is checked by sorting the stress results. The results are compared with those obtained by experiments and other existing models. This work provides a reference for the selection of the failure criteria and the calculation of the plastic collapse load.

Hydraulic calculation and dynamic analysis of columnar reversing gate

According to the hydraulic calculation principles of the orifice outflow, the discharge capacity of the columnar reversing gate under the partial opening condition was calculated and checked. Using ANSYS, a large finite element analysis software, the discharge process was simulated. The distribution rule of the velocities in the gate chamber and downstream channel was obtained. An FEM model of the columnar reversing gate was built, and the natural vibration properties of the gate were analyzed. Based on the Westergaard added mass method, the added mass caused by the fluid-structure coupling motion was taken into account, and the effects of the coupling interaction were discussed. The results show that the size of the small gates meets the demand for discharge capacity, the current in the gate chamber is quite turbulent, the trunnion and arms are obviously impacted by flow, and the effects of water on vibration characteristics are remarkable. The study provides a reference for the design and calculation of gates of the same type.

Analysis and design of axially loaded piles in rock

Despite significant advancements in in situ test techniques,construction practices,understanding of rock joint and rock mass behaviours,and numerical analysis methods,the design of bored concrete cast-insitu piles in rock is still largely based on the assessment of bearing capacity.However,for many of the rock conditions encountered,the bearing capacity of piles is a nebulous concept and a figment of the designer’s imagination.Even if it can be reasonably quantified,it has little,if any,significance to the performance of a pile in rock.The load carrying capacity of even low strength rock(in most situations)is far in excess of the strength of the structure(for example,a building column)transmitting the load.Unsatisfactory performance of a pile in rock is usually a displacement issue and is a function of rock mass stiffness rather than rock mass strength.In addition,poor pile performance is much more likely to result from poor construction practices than excessive displacement of the rock mass.Exceptions occur for footings that are undermined,or where unfavourable structure in the rock allows movement towards a free surface to occur.Standards,codes of practices,reference books and other sources of design information should focus foundation design in rock on displacement rather than strength performance.Ground investigations should measure rock mass stiffness and defect properties,as well as intact rock strength.This paper summarises the fundamental concepts relating to performance of piles in rock and provides a basis for displacement focused design of piles in rock.It also presents comments relating to how piles are modelled in widely used commercial finite element software for soil-structure interaction analysis,within the context of the back-analysis of a pile load test,and proposes recommendations for pile analysis and design.

Analysis and Research of Ice Loads Acting on Offshore Structures

Usually, the action of sea ice on offshore engineering structures is one of the controlling loads in cold waters engineering structure design. The reasonable selection of environmental condition and the physical mechanical properties of ice in the region are directly related to the structure design, operation and safety. In this paper, the sea ice force acting on the structure, the physical mechanical properties of ice and the selection of parameters in calculation are discussed. Some suggestions are proposed as to the calculation of various kinds of ice loads acting on the structure.

Stochastic Response Analysis of Piled Offshore Platforms to Earthquake Load

In this paper, using the theory of stochastic analysis of the response to earthquake load, a stochastic analysis method of the response of piled platforms to earthquake load has been established. In the method, the strong ground motion is considered as three dimensional stationary white noise process and the pile-soil interaction and water-structure interaction are considered. The stochastic response of a typical platform to earthquake load has been computed with this method and the results compared with those obtained with the response spectrum analysis method. The comparison shows that the stochastic analysis method of the response of piled platforms to earthquake load is suitable for this kind of analysis.

Hydroelastic Analysis of a Rectangular Plate Subjected to Slamming Loads

A hydroelastic analysis of a rectangular plate subjected to slamming loads is presented. An analytical model based on Wagner theory is used for calculations of transient slamming load on the ship plate. A thin isotropic plate theory is considered for determining the vibration of a rectangular plate excited by an external slamming force. The forced vibration of the plate is calculated by the modal expansion method. Analytical results of the transient response of a rectangular plate induced by slamming loads are compared with numerical calculations from finite element method. The theoretical slamming pressure based on Wagner model is applied on the finite element model of a plate. Good agreement is obtained between the analytical and numerical results for the structural deflection of a rectangular plate due to slamming pressure. The effects of plate dimension and wave profile on the structural vibration are discussed as well. The results show that a low impact velocity and a small wetted radial length of wave yield negligible effects of hydroelasticity.