High-speed directly modulated distributed feedback laser based on detuned loading and photon-photon resonance effect

A monolithic integrated two-section distributed feedback(TS-DFB)semiconductor laser for high-speed direct modulation is proposed and analyzed theoretically.The grating structure of the TS-DFB laser is designed by the reconstructionequivalent-chirp(REC)technique,which can reduce the manufacturing cost and difficulty,and achieve high wavelength controlling accuracy.The detuned loading effect and the photon-photon resonance(PPR)effect are utilized to enhance the modulation bandwidth of the TS-DFB laser,exceeding 37 GHz,while that of the conventional one-section DFB laser is only 16 GHz.When the bit rate of the non-return-to-zero(NRZ)signal reaches 55 Gb/s,a clear eye diagram with large opening can still be obtained.These results show that the proposed method can enhance the modulation bandwidth of DFB laser significantly.

Modulation bandwidth enhancement in monolithic integrated two-section DFB lasers based on the detuned loading effect

Modulation bandwidth enhancement in a directly modulated two-section distributed feedback(TS-DFB)laser based on a detuned loading effect is investigated and experimentally demonstrated.The results show that the 3-dB bandwidth of the TS-DFB laser is increased to 17.6 GHz and that chirp parameter can be reduced to 2.24.Compared to the absence of a detuned loading effect,there is a 4.6 GHz increase and a 2.45 reduction,respectively.After transmitting a 10 Gb/s non-return-to-zero(NRZ)signal through a 5-km fiber,the modulation eye diagram still achieves a large opening.Eight-channel laser arrays with precise wavelength spacing are fabricated.Each TS-DFB laser in the array has side mode suppression ratios(SMSR)>49.093 dB and the maximum wavelength residual<0.316 nm.

Energy Efficiency in Periods of Load Shedding and Detrimental Effects of Energy Dependence in the City of Maroua, Cameroon

During the years 2021 and 2022, the city of Maroua experienced repeated power blackouts. However, this locality has significant photovoltaic energy potential. Nevertheless, the evaluation of the electrical performance showed the dependence of the population on these fluctuations, which could be bypassed or suppressed. In most cases, the blackout occurs during high energy demand. In this paper, a method for evaluating electrical efficiency is proposed and its credibility has been demonstrated on the one hand, and on the other hand, a renewable energy production system is proposed. The Homer software has made possible the analysis of the proposed system and its impact on the environment has also been carried out. The techno-economic study of the system has proved that a solar photovoltaic farm associated with an energy storage system, with a capacity of 47 MW, can meet the energy demand of the town of Maroua. This alternative is profitable for this locality which lives in a precarious situation and a continuous need.

Fatigue Life Prediction under Service Load Considering Strengthening Effect of Loads below Fatigue Limit

Lightweight design requires an accurate life prediction for structures and components under service loading histories. However, predicted life with the existing methods seems too conservative in some cases, leading to a heavy structure. Because these methods are established on the basis that load cycles would only cause fatigue damage, ignore the strengthening effect of loads. Based on Palmgren-Miner Rule （PMR）, this paper introduces a new method for fatigue life prediction under service loadings by taking into account the strengthening effect of loads below the fatigue limit. In this method, the service loadings are classified into three categories： damaging load, strengthening load and none-effect load, and the process for fatigue life prediction is divided into two stages： stage I and stage II, according to the best strengthening number of cycles. During stage I, fatigue damage is calculated considering both the strengthening and damaging effect of load cycles. While during stage II, only the damaging effect is considered. To validate this method, fatigue lives of automobile half shaft and torsion beam rear axle are calculated based on the new method and traditional methods, such as PMR and Modified Miner Rule （MMR）, and fatigue tests of the two components are conducted under service loading histories. The tests results show that the percentage errors of the predicted life with the new method to mean life of tests for the two components are –3.78% and –1.76% separately, much lesser than that with PMR and MMR. By considering the strengthening effect of loads below the fatigue limit, the new method can significantly improve the accuracy for fatigue life prediction. Thus lightweight design can be fully realized in the design stage.

Fatigue Life Evaluation Method for Foundry Crane Metal Structure Considering Load Dynamic Response and Crack Closure Effect

To compensate for the shortcomings of quasi-static law in anti-fatigue analysis of foundry crane metal structures,the fatigue life evaluation method of foundry crane metal structure considering load dynamic response and crack closure effect is proposed.In line with the theory of mechanical vibration,a dynamic model of crane structure during the working cycle is constructed,and dynamic coefficients under diverse actions are analysed.Calculation models of the internal force dynamic change process of dangerous cross-sections and a simulation model of first principal stress-time history are established by using the steel structure design criteria,which is utilised to extract the change of first principal stress of danger points over time.Then,the double-parameter stress spectrum is obtained by the rain flow counting method.The fatigue life calculation formula is corrected by introducing a crack closure parameter that can be calculated by the stress ratio and the effective stress ratio.Under the finite element model imported into Msc.Patran,crack propagation analysis is performed by the growth method in the fatigue integration module Msc.Fatigue.Taking the metal structure of a 100/40t-28.5m foundry crane with track offset as an example,the accuracy of calculation results and the feasibility and applicability of the proposed method are verified by theoretical calculation and finite element simulation,which provide a theoretical basis for improvement of the fatigue resistance design of foundry cranes.

Characteristics of gravity signal and loading effect in China

The complex geographical environment in China makes its gravity signals miscellaneous.This work gives a comprehensive representation and explanation in secular trend of gravity change in different regions,the key features of which include positive trend in inner Tibet Plateau and South China and negative trend in North China plain and high mountain Asia（HMA）.We also present the patterns of amplitudes and phases of annual and semiannual change.The mechanism underlying the semiannual period is explicitly discussed.The displacement in three directions expressed in terms of geo-potential spherical coefficients and load Love numbers are given.A case study applied with these equations is presented.The results show that Global Positioning System（GPS） observations can be used to compare with Gravity Recovery and Climate Experiment（GRACE） derived displacement and the vertical direction has a signal-noise-ratio of about one order of magnitude larger than the horizontal directions.

Effects of time lag and stress loading rate on permeability in low permeability reservoirs

In order to study the effect of time lag and stress loading rates on rock deformation,the conventional stepped stress loading mode was changed into a continuous mode to investigate the effect of effective pressure on permeability and porosity.The time lag effect of rock deformation illustrating the relationship between changes in permeability and steady time was studied.Permeability reduction ratios were measured under different stress loading rates which were achieved by different pump rate settings.The results show that permeability and porosity gradually decrease with increases in effective pressure.Permeability at high effective pressure attains stability quickly.Steady times at low effective pressure are very long.Reduction in permeability at lower stress loading rates is small,while,in contrast,it is large at high stress loading rates.

Vibration Effect and Damage Evolution Characteristics of Tunnel Surrounding Rock Under Cyclic Blasting Loading

Model test studies based on the similarity theory were conducted to investigate vibration effect and damage evolution characteristics of tunnel surrounding rock under push-type cyclic blasting excavation.The model was constructed with a ratio of 1∶15.By simulating the tunnel excavation of push-type cyclic blasting,the influence of the blasting parameter change on vibration effect was explored.The damage degree of tunnel surrounding rock was evaluated by the change of the acoustic wave velocity at the same measuring point after blasting.The relationship between the damage evolution of surrounding rock and blasting times was established.The research results show that：（1）In the same geological environment,the number of delay initiation is larger,the main vibration frequency of blasting seismic wave is higher,and the attenuation of high frequency signal in the rock and soil is faster.The influence of number of delay initiation on blasting vibration effect cannot be ignored;（2）Under push-type cyclic blasting excavation,there were great differences in the decreasing rates of acoustic wave velocity of the measuring points which have the same distance to the blasting region at the same depth,and the blasting damage ranges of surrounding rock were typically anisotropic at both depth and breadth;（3）When blasting parameters were basically kept as the same,the growth trend of the cumulative acoustic wave velocity decreasing rate at the measuring point was nonlinear under different cycle blasting excavations;（4）There were nonlinear evolution characteristics between the blasting cumulative damage（D）of surrounding rock and blasting times（n）under push-type cyclic blasting loading,and different measuring points had corresponding blasting cumulative damage propagation models,respectively.The closer the measuring point was away from the explosion source,the faster the cumulative damage extension.Blasting cumulative damage effect of surrounding rock had typically nonlinear evolution properties and anisotropic characteristics.

An improved model for predicting effective Young's modulus of the twisted structure under cyclic loading:taking into account the untwisting effect

Twist structures have diverse applications, ranging from dragline, electrical cable, and intelligent structure. Among these applications, tension deformation can＇t be avoided during the fabrication and working processes, which often leads to the twist structure rotation （called untwisting effect） and twist pitch increasing. As a consequence, this untwisting behavior has a large effect on the effective Young＇s modulus. In this paper, we present an improved model based on the classical Costello＇s theory to predict the effective Young＇s modulus of the basic structure, twisted by three same copper strands under cyclic loading. Series of experiments were carried out to verify the present model taking into account the untwisting effect. The experimental results have better agreements with the presented model than the common Costello＇s model.

Effect of Loading Paths on Hydroforming Tubular Square Components

The influence of loading path on tube hydroforming process is discussed in this paper with finiteelement simulation. Four different loading paths are utilized in simulating the forming process of square tubular component with hydroforming and the result of different loading path is presented. Among the result. the thickness distribution of bilinear loading path is the most uniform one. It shows that the increase of punch displacement in the stage of high pressure is beneficial to the forming of component for optimized Stress condition.

Effect of Thermal Cycling under Load on Martensite Transformation and Two-way Shape Memory Effect in a TiNi Alloy

The effect of thermal cycling under loading on martensitic transformation and two-way shape memory effect was investigated for Ti-49.8 at. pci Ni alloy. It is shown that Ms and Mf temperature increase with increasing the number of cycles, while As and Af temperature decrease during thermal cycling. The total strain et and permanent strain ep increase with increasing applied stress and number of cycles. The two-way shape memory effect can be improved by proper thermal cycling training under loading, while excessively high applied stress results in the deterioration of TWSME. The reason for the changes in martensitic transformation characteristics and two-way shape memory effect during thermal cycling under loading is discussed based on the analysis of microstructure by TEM observations.

Mechanical Modeling of Dike Pathways in the Crust: Effect of Layering and Surface Loads

Magma is generated mostly in the Earth’s mantle by decompression melting and transported through the crust to reach the Earth’s surface.The main mechanism for magma transport is diking,but the pathways taken by

Simulation and Experimental Design of Load Adaptive Braking System on Two Wheeler

The braking quality is considered the main execution of the adaptive control framework that impacts the vehicle safety and rides solace astoundingly notably the stopping distance.This research work aims to create a pattern and design of an electromechanically adjusted lever that multiplies the applied braking force depending on the inputs given by the sensors to reduce the stopping distance of the vehicle.It is carried out using two main parts of the two-wheeler vehicle:thefirst part deals with the detection of load acting on the vehicle and identifying the required braking force to be applied,and the second part deals with the micro-controller which activates the stepper motor for varying the mechanical leverage ratio from various loads on the vehicle using two actively movable wedges.The electromechanically operated variable braking force system is developed to actuate the braking system based on the load on the motorcycle.The MATLAB simulation and experimental work are carried out for various loading(driver and pillion)conditions on a two-wheeler.The results indicate that the proposed electronically operated braking system is more effective than the conventional braking system for various loads and vehicle speeds.Specifically,the stopping distance of the vehicle is decreased significantly by about 4.9%between the con-ventional braking system and the simulated proposed system.Further,the experi-mental results show that the stopping distance is condensed by about 4.1%.The validation between simulated and experimental results revealed a great deal with the least error percentage of about 0.8%.

Analysis of the blasting effect on the electric shove loading efficiency of the open pit

The connection between blasting cost and comprehensive cost is the main concern.Some blasting effect factors (such as unit explosive consumption,uniformity of blockness,shape and porosity of blasting heap),which had an influence on electric shove loading efficiency,were analyzed.In the end a project to properly increase in blasting cost to decrease the comprehensive cost was put forward.At the same time,the hole-by-hole blasting is effective technology to improve blasting effect.

Evaluating the Effective Microbial Supplementation of Feed on the Load of Salmonella in Two Lymph Nodes of Beef Cattle in Eastern Ethiopia

The present study was conducted to evaluate the role of effective microbial supplementation to feed on the load of Salmonella in the mesenteric and sub-iliac lymph nodes of beef cattle. Bulls of Harer cattle breed managed at Chercher Oda-Bultum Farmers Union beef Farm were used as study subject. A total of 130 bulls were used using double blinded randomized controlled field trial based on parallel group design from January 2018 to July 2018. The study animals were randomly assigned to the treatment group (n = 100) and control group (n = 30). The feed of treatment group was mixed with EM at dose of 5 × 1010 cfu/day/head and supplemented for 90, 100 and 115 days while that of the control group was mixed with molasses, which acts as placebo. Both the treatment and control were slaughtered and two lymph nodes were collected from each animal under strict sterile condition and processed for the isolation and identification of Salmonella using standard procedure. A significant (p = 0.001) reduction in the load of Salmonella was observed in the lymph node of treatment group as compared to the control group. The load of Salmonella was significantly affected by length of feeding period and age of bulls. This study indicated that effective microbial supplementation to bulls from Harar cattle reduces the load of Salmonella in the lymph node of beef cattle thereby potentially minimizing the economic and public health impacts of Salmonella infection.

THE GENERAL SOLUTION OF SECOND ORDER EFFECTS IN ELASTIC HALF-SPACE ACTED UPON BY A NON-UNIFORM SHEAR LOAD

This paper is a continuation of [1]. A closed form solution to the second order elasticity problem, when an isotropic compressible elastic half-space undergoes a deformation owing to a non-uniformly distributed shear load, is presented. The method of integral transform is employed to determine the solutions.

THE ILLUSTRATION CALCULATIONS OF SECOND ORDER EFFECTS IN ELASTIC HALF-SPACE ACTED UPON BY A NON-UNIFORM SHEAR LOAD

This paper is a continuation of [1]. An example is discussed in derail to illustrate the second order effects. Numerical calculations for the second order elastic material for the z-direction displacement and the stress t(rz) are carried out. It is found that the second order effect is to reduce z-direction displacement and to decrease t(rz)inside the circle but to increase its value outside the circle.

A Study of Retention Time Gradient Effect of Gradientally Loaded Columns

In this work, the 'retention time gradient effect' of gradient GC columns is intensively studied to establish some equations and formulas for structure calculation of chromatographic columns. In addition, the relevant computer programs are designed.