ULTIMATE LOAD-BEARING CAPACITY OF CYLINDER DERIVED FROM AUTOFRETTAGE UNDER IDEAL CONDITION

According to the basic theory on autofrettage and according to the 4th strength theory, several parameters and their relations are studied under ideal condition, including σej/σy, the equivalent stress of total stresses at elastoplastic juncture; σei/σy, the equivalent stress of total stresses at inside surface; σej＇/σy, the equivalent stress of residual stresses at elastoplastic juncture; σei＇/σy, the equivalent stress of residual stresses at inside surface; and p/σy, load-bearing capacity of an autofrettaged cylinder. By theoretical study on relations between the parameters, noticeable results and laws are achieved： to satisfy ｜σei＇｜=σy. the relation between kj and k is, k^2lnkj^2-k^2-kj^2＋2=0, when k→∞, kj = √e = 1.648 72, as based on the 3rd strength theory, where k is the outside/inside radius ratio of a cylinder, kj is the ratio of elastoplastic juncture radius to inside radius of a cylinder; If the plastic region covers the whole wall of a cylinder, for compressive yield not to occur after removing autofrettage pressure, the ultimate k is k=-2.218 46 as based on the 3rd strength theory; With k=2.218 46, a cylinder＇s ultimate load-bearing capacity equals its entire yield pressure, or p/σy=21nk/√3; The maximum and optimum load-bearing capacity of an autofrettaged cylinder is just 2 times the loading which an unautofrettaged cylinder can bear elastically, or p/σy=2（k^2-1）/√3 k^2, and the limit of the load-bearing capacity of an autofrettaged cylinder is also just 2 times that of an unautofrettaged cylinder. The conclusions are the same as based on the 3rd strength theory, but some equations are different from each other.

Effect of Optimum Plastic Depth on Stresses and Load-bearing Capacity of Autofrettaged Cylinder

Autofrettage is an effective measure to even distribution of stresses and raise load-bearing capacity for （ultra-）high pressure apparatus. Currently, the research on autofrettage has focused mostly on specific engineering problems, while general theoretical study is rarely done. To discover the general law contained in autofrettage theory, by the aid of the authors’ previous work and according to the third strength theory, theoretical problems about autofrettage are studied including residual stresses and their equivalent stress, total stresses and their equivalent stress, etc. Because of the equation of optimum depth of plastic zone which is presented in the authors’ previous work, the equations for the residual stresses and their equivalent stress as well as the total stress and their equivalent stress are simplified greatly. Thus the law of distribution of the residual stresses and their equivalent stress as well as the total stress and their equivalent stress and the varying tendency of these stresses are discovered. The relation among various parameters are revealed. The safe and optimum load-bearing conditions for cylinders are obtained. According to the results obtained by theoretical analysis, it is shown that if the two parameters, namely ratio of outside to inside radius, k, and depth of plastic zone, kj, meet the equation of optimum depth of plastic zone, when the pressure contained in an autofrettaged cylinder is lower than two times the initial yield pressure of the unautofrettaged cylinder, the equivalent residual stress and the equivalent total stress at the inside surface as well as the elastic-plastic juncture of a cylinder are lower than yield strength. When an autofrettaged cylinder is subjected to just two times the initial yield pressure of the unautofrettaged cylinder, the equivalent total stress within the whole plastic zone is just identically equal to the yield strength, or it is a constant. The proposed research theoretically depicts the stress state of ultra-）high pressure autofrettaged cylinder more accurately and more reasonably and provides the reference for design of （ultra-）high pressure apparatus.

Load-Bearing Capacity of the Footing Resting on a Reinforced Fly Ash Slope

In several parts of the world, disposal of waste materials such as fly ash is a great problem. Application of waste materials as structural fills in foundations is one of the best solutions to disposal problems, because wastes can be used in large volumes in such applications. There may be difficulty due to poor load-bearing capacity of fly ash, especially when footing rests on the top of the fly ash fill slope. Inclusion of polymeric reinforcements as horizontal sheets within the fill may be one of the most viable solutions to improving the load-bearing capacity of reinforced fly ash slope, and it is particularly important for the situations where foundations need to be located either on the top of a slope or on slope itself. The present work is aimed at investigating the efficacy of a single layer of reinforcement in improving the lo, ad-bearing capacity when it gets incorporated within the body of a model fly ash embankment slope. An increase in load bearing capacity due to the incorporation of reinforcement in the model slope was found by conducting laboratory tests. Experimental results were compared by numerical values obtained using software GEO5 and PLAXIS.

A Bio-inspired Mutual-hook Strategy for the Soft Finger to Improve Load-bearing Capacity and Grasping Stability

Soft grippers have great potential applications in daily life,since they can compliantly grasp soft and delicate objects.However,the highly elastic fingers of most soft grippers are prone to separate from each other while grasping objects due to their low stiffness,thus reducing the grasping stability and load-bearing capacity.To tackle this problem,inspired from the venus flytrap plant,this work proposes a mutual-hook mechanism to restrain the separation and improve the grasping performance of soft fingers.The novel soft gripper design consists of three modules,a soft finger-cot,two Soft Hook Actuators(SHAs)and two sliding mechanisms.Here,the soft finger-cot covers on the soft finger,increasing the contact area with the target object,two SHAs are fixed to the left and right sides of the finger-cot,and the sliding mechanisms are designed to make SHAs stretch flexibly.Experiments demonstrate that the proposed design can restrain the separation of soft fingers substantially,and the soft fingers with the finger-cots can grasp objects three times heavier than the soft fingers without the proposed design.The proposed design can provide invaluable insights for soft fingers to restrain the separation while grasping,thus improving the grasping stability and the load-bearing capacity.

Exploring the relevance between load-bearing capacity and surface friction behavior based on a layered hydrogel cartilage prototype

Cartilage is well lubricated over a lifetime and this phenomenon is attributed to both of the surface hydration lubrication and the matrix load-bearing capacity.Lubricious hydrogels with a layered structure are designed to mimic cartilage as potential replacements.While many studies have concentrated on improving surface hydration to reduce friction,few have experimentally detected the relationship between load-bearing capacity of hydrogels and their interface friction behavior.In this work,a bilayer hydrogel,serving as a cartilage prototype consisted of a top thick hydrated polymer brush layer and a bottom hydrogel matrix with tunable modulus was designed to investigate this relationship.The coefficient of friction(COF,μ)is defined as the sum of interfacial component(μInt)and deformation/hysteresis component(μHyst).The presence of the top hydration layer effectively dissipates contact stress and reduces the interface interaction(μInt),leading to a stable and low COF.The contribution of mechanical deformation(μHyst)during the sliding shearing process to COF can be significantly reduced by increasing the local mechanical modulus,thereby enhancing the load-bearing capacity.These results show that the strategy of coupling surface hydration layer with a high load-bearing matrix can indeed enhance the lubrication performance of hydrogel cartilage prototypes,and implies a promising routine for designing robust soft matter lubrication system and friction-control devices.

A comparison study on structure-function relationship of polysaccharides obtained from sea buckthorn berries using different methods:antioxidant and bile acid-binding capacity

In this study,the structural characters,antioxidant activities and bile acid-binding ability of sea buckthorn polysaccharides(HRPs)obtained by the commonly used hot water(HRP-W),pressurized hot water(HRP-H),ultrasonic(HRP-U),acid(HRP-C)and alkali(HRP-A)assisted extraction methods were investigated.The results demonstrated that extraction methods had significant effects on extraction yield,monosaccharide composition,molecular weight,particle size,triple-helical structure,and surface morphology of HRPs except for the major linkage bands.Thermogravimetric analysis showed that HRP-U with filamentous reticular microstructure exhibited better thermal stability.The HRP-A with the lowest molecular weight and highest arabinose content possessed the best antioxidant activities.Moreover,the rheological analysis indicated that HRPs with higher galacturonic acid content and molecular weight showed higher viscosity and stronger crosslinking network(HRP-C,HRP-W and HRP-U),which exhibited stronger bile acid binding capacity.The present findings provide scientific evidence in the preparation technology of sea buckthorn polysaccharides with good antioxidant and bile acid binding capacity which are related to the structure affected by the extraction methods.

Additively manufactured Ti–Ta–Cu alloys for the next-generation load-bearing implants

Bacterial colonization of orthopedic implants is one of the leading causes of failure and clinical complexities for load-bearing metallic implants. Topical or systemic administration of antibiotics may not offer the most efficient defense against colonization, especially in the case of secondary infection, leading to surgical removal of implants and in some cases even limbs. In this study, laser powder bed fusion was implemented to fabricate Ti3Al2V alloy by a 1:1 weight mixture of CpTi and Ti6Al4V powders. Ti-Tantalum(Ta)–Copper(Cu) alloys were further analyzed by the addition of Ta and Cu into the Ti3Al2V custom alloy. The biological,mechanical, and tribo-biocorrosion properties of Ti3Al2V alloy were evaluated. A 10 wt.% Ta(10Ta) and 3 wt.% Cu(3Cu) were added to the Ti3Al2V alloy to enhance biocompatibility and impart inherent bacterial resistance. Additively manufactured implants were investigated for resistance against Pseudomonas aeruginosa and Staphylococcus aureus strains of bacteria for up to 48 h. A 3 wt.% Cu addition to Ti3Al2V displayed improved antibacterial efficacy, i.e.78%–86% with respect to CpTi. Mechanical properties for Ti3Al2V–10Ta–3Cu alloy were evaluated, demonstrating excellent fatigue resistance, exceptional shear strength, and improved tribological and tribo-biocorrosion characteristics when compared to Ti6Al4V. In vivo studies using a rat distal femur model revealed improved early-stage osseointegration for alloys with10 wt.% Ta addition compared to CpTi and Ti6Al4V. The 3 wt.% Cu-added compositions displayed biocompatibility and no adverse infammatory response in vivo. Our results establish the Ti3Al2V–10Ta–3Cu alloy’s synergistic effect on improving both in vivo biocompatibility and microbial resistance for the next generation of load-bearing metallic implants.

Durable K-ion batteries with 100% capacity retention up to 40,000 cycles

Currently,the major challenge in terms of research on K-ion batteries is to ensure that they possess satisfactory cycle stability and specific capacity,especially in terms of the intrinsically sluggish kinetics induced by the large radius of K+ions.Here,we explore high-performance K-ion half/full batteries with high rate capability,high specific capacity,and extremely durable cycle stability based on carbon nanosheets with tailored N dopants,which can alleviate the change of volume,increase electronic conductivity,and enhance the K+ion adsorption.The as-assembled K-ion half-batteries show an excellent rate capability of 468 mA h g^(−1) at 100 mA g^(−1),which is superior to those of most carbon materials reported to date.Moreover,the as-assembled half-cells have an outstanding life span,running 40,000 cycles over 8 months with a specific capacity retention of 100%at a high current density of 2000 mA g^(−1),and the target full cells deliver a high reversible specific capacity of 146 mA h g^(−1) after 2000 cycles over 2 months,with a specific capacity retention of 113%at a high current density of 500 mA g^(−1),both of which are state of the art in the field of K-ion batteries.This study might provide some insights into and potential avenues for exploration of advanced K-ion batteries with durable stability for practical applications.

A comparative study of data-driven battery capacity estimation based on partial charging curves

With its generality and practicality, the combination of partial charging curves and machine learning(ML) for battery capacity estimation has attracted widespread attention. However, a clear classification,fair comparison, and performance rationalization of these methods are lacking, due to the scattered existing studies. To address these issues, we develop 20 capacity estimation methods from three perspectives:charging sequence construction, input forms, and ML models. 22,582 charging curves are generated from 44 cells with different battery chemistry and operating conditions to validate the performance. Through comprehensive and unbiased comparison, the long short-term memory(LSTM) based neural network exhibits the best accuracy and robustness. Across all 6503 tested samples, the mean absolute percentage error(MAPE) for capacity estimation using LSTM is 0.61%, with a maximum error of only 3.94%. Even with the addition of 3 m V voltage noise or the extension of sampling intervals to 60 s, the average MAPE remains below 2%. Furthermore, the charging sequences are provided with physical explanations related to battery degradation to enhance confidence in their application. Recommendations for using other competitive methods are also presented. This work provides valuable insights and guidance for estimating battery capacity based on partial charging curves.

Sealing capacity evaluation of underground gas storage under intricate geological conditions

Evaluating underground gas storage(UGS)sealing capacity is essential for its safe construction and operational efficiency.This involves evaluating both the static sealing capacity of traps during hydrocarbon accumulation and the dynamic sealing capacity of UGS under intensive gas injection and withdrawal,and alternating loads.This study detailed the methodology developed by Sinopec.The approach merges disciplines like geology,geomechanics,and hydrodynamics,employing both dynamic-static and qualitative-quantitative analyses.Sinopec's evaluation methods,grounded in the in situ stress analysis,include mechanistic studies,laboratory tests,geological surveys,stress analysis,and fluid-solid interactions.Through tests on the static and dynamic sealing capacity of UGS,alongside investigations into sealing mechanisms and the geological and geomechanical properties of cap rocks and faults,A geomechanics-rock damage-seepage mechanics dynamic coupling analysis method has been developed to predict in situ stress variations relative to pore pressure changes during UGS operations and evaluate fault sealing capacity and cap rock integrity,thereby setting the maximum operational pressures.Utilizing this evaluation technique,Sinopec has defined performance metrics and criteria for evaluating the sealing capacity of depleted gas reservoirs,enabling preliminary sealing capacity evaluations at UGS sites.These evaluations have significantly informed the design of UGS construction schemes and the evaluation of fault sealing capacity and cap rock integrity during UGS operations.

Insight into the capacity degradation and structural evolution of single-crystal Ni-rich cathodes

Single-crystal Ni-rich cathodes are a promising candidate for high-energy lithium-ion batteries due to their higher structural and cycling stability than polycrystalline materials.However,the phase evolution and capacity degradation of these single-crystal cathodes during continuous lithation/delithation cycling remains unclear.Understanding the mapping relationship between the macroscopic electrochemical properties and the material physicochemical properties is crucial.Here,we investigate the correlation between the physical-chemical characteristics,phase transition,and capacity decay using capacity differential curve feature identification and in-situ X-ray spectroscopic imaging.We systematically clarify the dominant mechanism of phase evolution in aging cycling.Appropriately high cut-off voltages can mitigate the slow kinetic and electrochemical properties of single-crystal cathodes.We also find that second-order differential capacity discharge characteristic curves can be used to identify the crystal structure disorder of Ni-rich cathodes.These findings constitute a step forward in elucidating the correlation between the electrochemical extrinsic properties and the physicochemical intrinsic properties and provide new perspectives for failure analysis of layered electrode materials.

Load-bearing characteristics and energy evolution of fractured rock masses after granite and sandstone grouting

Experiments on grouting-reinforced rock mass specimens with different particle sizes and features were carried out in this study to examine the effects of grouting reinforcement on the load-bearing characteristics of fractured rock mass.The strength and deformation features of grouting-reinforced rock mass were analyzed under different loading manners;the energy evolution mechanism of grouting-reinforced rock mass specimens with different particle sizes and features was investigated;the energy dissipation ratio and post-peak stress decreasing rate were employed to evaluate the bearing stability of grouting-reinforced rock mass.The results show that the strength and ductility of granite-reinforced rock mass(GRM)under biaxial loading are higher than that of sandstone-reinforced rock mass(SRM)under uniaxial loading.Besides,the energy evolution characteristics of grouting-reinforced rock mass under uniaxial and biaxial loading mainly could be divided into early,middle,and late stages.In the early stage,total,elastic,and dissipation energies were quite small with flatter curves;in the middle stage,elastic energy increased rapidly,whereas dissipation energy increased slowly;in the late stage,dissipation energy increased sharply.The energy dissipation ratio was used to represent the pre-peak plastic deformation.Under uniaxial loading,this ratio increased as the particle size increased and the pre-peak plastic deformation of grouting-reinforced rock mass became larger;under biaxial loading,it dropped as the particle size increased,and the pre-peak plastic deformation of grouting-reinforced rock mass became smaller.The post-peak stress decline rate A_(v) was used to assess the post-peak bearing performance of grouting-reinforced rock mass.Under uniaxial loading,parameter A_(v) exhibited reduction as the particle size kept increasing,and the ability of post-peak of grouting-reinforced rock mass to allow deformation development was greater,and the bearing capacity was greater;under biaxial loading,A_(v) increased with the particle size,and the ability of post-peak of grouting-reinforced rock mass to allow deformation development was low and the bearing capacity was reduced.The findings are considered instrumental in improving the stability of the roadway-surrounding rock by granite and sandstone grouting.

Effect of Trimetazidine on Functional Capacity in Patient with Ischaemic Cardiomyopathy (TOFCAPI)

Objective: This study aimed to evaluate the efficacy of trimetazidine on exercise capacity via a six-minute walk test in patients with ischaemic cardiomyopathy and also evaluate the effect of trimetazidine on left ventricular function via echocardiography in the same population. Methods: This prospective observational study, conducted at the National Institute of Cardiovascular Diseases in Dhaka, Bangladesh, enrolled 200 patients with ischaemic cardiomyopathy and a depressed left ventricular ejection fraction (LVEF Results: In this study (n = 200) of ischaemic cardiomyopathy patients, the mean age was 58 years, with 76% of the patients being male. All study subjects received GDMT (Guideline-Directed Medical Therapy) for angina and heart failure. Those who received the modified released form of trimetazidine developed lesions during the 1st and 2nd follow-ups, during which the LVEF, LVIDd, and six-minute walk distance significantly improved (p Conclusion: The findings of the present study demonstrated that the addition of modified-release trimetazidine to GDMT can improve exercise capacity and left ventricular function in patients with ischaemic cardiomyopathy.

Effect of Cardiac Rehabilitation on Physical Capacity of Heart Failure Patients in Senegal

Background: Heart failure is a chronic and severe condition that often results from various heart diseases. Cardiac rehabilitation (CR) is currently a crucial component in managing this condition. The aim was to assess the effects of cardiac rehabilitation on physical capacity of heart failure patients. Methods: This was a cross-sectional study conducted from February 1, 2021, to June 30, 2023. We included all patients with heart failure who underwent cardiac rehabilitation. Data analysis was performed using SPSS software version 24.0, with a significance level set at p Results: The study included 87 heart failure patients, with a male-to-female ratio of 1.8. Mean age was 57.10 years (±11.75). Coronary artery disease was the primary cause of heart failure, accounting for 75.9% of cases. Atrial fibrillation was present in 4.7% of cases. Following cardiac rehabilitation, Left Ventricular Ejection Fraction increased from 40.15% to 49.48% (p = 0.001). Resting heart rate decreased significantly from 81.4 bpm to 68.3 bpm (p = 0.000), and the number of METS increased from 4.3 to 6.57 (+56.8%;p = 0.000). The mean distance covered in the 6-minute walk test significantly increased from 337.8 meters to 522.7 meters (p = 0.000), reflecting a gain of 183.5 meters. Moreover, the increase in the number of METS was more pronounced in females (p = 0.001), non-obese individuals (p = 0.000), non-diabetics (p = 0.001), non-sedentary individuals (p = 0.000), and non-smokers (p = 0.000). The study reported a low readmissions rate of 2.2% and a mortality rate of 1.1%. Conclusion: Our study demonstrates that cardiac rehabilitation is beneficial for black African heart failure patients, resulting in significant improvements in symptoms, physical and capacity.

Functional Capacity of Patients with Venous Thromboembolic Disease Six to Twelve Months after Treatment

Background: Venous thromboembolism (VTE) is among the leading causes of hospital-related disability-adjusted life years lost. We aimed to determine the prevalence and determinants of functional capacity impairment six to twelve months after an acute VTE event. Methods: This was a cross-sectional study conducted between January and April 2021 in two referral hospitals of Yaoundé, including consenting adult patients admitted to these hospitals six to twelve months ago for VTE. We excluded dead patients and those with any comorbidity or symptoms limiting physical activity. The functional outcome was assessed with the six-minute walk test. Functional capacity impairment was defined as walking distance lower than the expected value. Results: We included 27 cases in this study with a mean age of 53.2 ± 14.4 years. The prevalence of functional capacity impairment was 29.6% (95% CI: 14.8 - 48.1). Factors associated with poor functional outcome were obesity (OR: 59.5;95% CI: 4.6 - 767.2;p - 207.4;p = 0.017), massive PE (OR: 30;95% CI: 2.5 - 354;p = 0.004), and poor adherence to treatment (OR: 30.3;95% CI: 2.5 - 333.3;p = 0.004). Conclusion: Functional capacity impairment is common in the medium-term after VTE and factors associated with this poor outcome are obesity, the severity of the VTE, and poor adherence to treatment.

Dust-Holding Capacity and Bio-Chemical Changes of Plant Species Growing in an Around Opencast Mining Area of Bundelkhand Region of Uttar Pradesh, India

The present study has been carried out on a total of 50 available plant species to assess their dust-capturing capacity and biochemical performances in and around open cast granite mine areas of Jhansi district and Bundelkhand University campus treated as control site. Plant species existing under a polluted environment for a long time may be considered as potentially resistant species and recommended for green belt design in mining areas, especially to cope with dust pollution. Results showed the pollution level, especially of mining-originated dust particles holding capacity of leaves and effects of different biochemical parameters (Total Chlorophyll, Protein and Carotenoid) of existing plant species both from mining areas as well as from Bundelkhand University campus. Based on their performances, Tectona grandis L., Ficus hispida L., Calotropis procera Aiton., Butea monosperma Lam. and Ficus benghalensis L., etc. are highly tolerant species while Ficus infectoria L., Artocarpus heterophyllus Lam., Ipomoea purpurea L., Allianthus excelsa Roxb. and Bauhinia variegata L. are intermediate tolerant species. T. grandis had shown the highest dust-holding capacity (2.566 ± 0.0004 mg/cm2) whereas Albizia procera (0.018 ± 0.0002 mg/cm2) was found to be the lowest dust-holding capacity. Our findings also showed that the T. grandis and F. hispida have significant dust deposition with minimal effect of dust on their leaf chlorophyll (17.447 ± 0.019 mg/g and 14.703 ± 0.201 mg/g), protein (0.699 ± 0.001 mg/g and 0.604 ± 0.002 mg/g) and carotenoid (0.372 ± 0.003 mg/g and 0.354 ± 0.003 mg/g) content respectively among all selected plant species. Therefore, in the present investigation, plant species with high tolerance to high dust-holding capacity on their leaf surfaces are preferable for green corridors as open cast granite mines and their adjacent areas.

Stochastic Air Traffic Flow Management for Demand and Capacity Balancing Under Capacity Uncertainty

This paper introduces an innovative approach to the synchronized demand-capacity balance with special focus on sector capacity uncertainty within a centrally controlled collaborative air traffic flow management(ATFM)framework.Further with previous study,the uncertainty in capacity is considered as a non-negligible issue regarding multiple reasons,like the impact of weather,the strike of air traffic controllers(ATCOs),the military use of airspace and the spatiotemporal distribution of nonscheduled flights,etc.These recessive factors affect the outcome of traffic flow optimization.In this research,the focus is placed on the impact of sector capacity uncertainty on demand and capacity balancing(DCB)optimization and ATFM,and multiple options,such as delay assignment and rerouting,are intended for regulating the traffic flow.A scenario optimization method for sector capacity in the presence of uncertainties is used to find the approximately optimal solution.The results show that the proposed approach can achieve better demand and capacity balancing and determine perfect integer solutions to ATFM problems,solving large-scale instances(24 h on seven capacity scenarios,with 6255 flights and 8949 trajectories)in 5-15 min.To the best of our knowledge,our experiment is the first to tackle large-scale instances of stochastic ATFM problems within the collaborative ATFM framework.

An Improved Image Steganography Security and Capacity Using Ant Colony Algorithm Optimization

This advanced paper presents a new approach to improving image steganography using the Ant Colony Optimization(ACO)algorithm.Image steganography,a technique of embedding hidden information in digital photographs,should ideally achieve the dual purposes of maximum data hiding and maintenance of the integrity of the cover media so that it is least suspect.The contemporary methods of steganography are at best a compromise between these two.In this paper,we present our approach,entitled Ant Colony Optimization(ACO)-Least Significant Bit(LSB),which attempts to optimize the capacity in steganographic embedding.The approach makes use of a grayscale cover image to hide the confidential data with an additional bit pair per byte,both for integrity verification and the file checksumof the secret data.This approach encodes confidential information into four pairs of bits and embeds it within uncompressed grayscale images.The ACO algorithm uses adaptive exploration to select some pixels,maximizing the capacity of data embedding whileminimizing the degradation of visual quality.Pheromone evaporation is introduced through iterations to avoid stagnation in solution refinement.The levels of pheromone are modified to reinforce successful pixel choices.Experimental results obtained through the ACO-LSB method reveal that it clearly improves image steganography capabilities by providing an increase of up to 30%in the embedding capacity compared with traditional approaches;the average Peak Signal to Noise Ratio(PSNR)is 40.5 dB with a Structural Index Similarity(SSIM)of 0.98.The approach also demonstrates very high resistance to detection,cutting down the rate by 20%.Implemented in MATLAB R2023a,the model was tested against one thousand publicly available grayscale images,thus providing robust evidence of its effectiveness.

Effect of speed humps on instantaneous traffic emissions in a microscopic model with limited deceleration capacity

As a common transportation facility, speed humps can control the speed of vehicles on special road sections to reduce traffic risks. At the same time, they also cause instantaneous traffic emissions. Based on the classic instantaneous traffic emission model and the limited deceleration capacity microscopic traffic flow model with slow-to-start rules, this paper has investigated the impact of speed humps on traffic flow and the instantaneous emissions of vehicle pollutants in a single lane situation. The numerical simulation results have shown that speed humps have significant effects on traffic flow and traffic emissions. In a free-flow region, the increase of speed humps leads to the continuous rise of CO_(2), NO_(X) and PM emissions. Within some density ranges, one finds that these pollutant emissions can evolve into some higher values under some random seeds. Under other random seeds, they can evolve into some lower values. In a wide moving jam region, the emission values of these pollutants sometimes appear as continuous or intermittent phenomenon. Compared to the refined Na Sch model, the present model has lower instantaneous emissions such as CO_(2), NO_(X) and PM and higher volatile organic components(VOC) emissions. Compared to the limited deceleration capacity model without slow-to-start rules, the present model also has lower instantaneous emissions such as CO_(2), NO_(X) and PM and higher VOC emissions in a wide moving jam region. These results can also be confirmed or explained by the statistical values of vehicle velocity and acceleration.

Prediction of Damping Capacity Demand in Seismic Base Isolators via Machine Learning

Base isolators used in buildings provide both a good acceleration reduction and structural vibration control structures.The base isolators may lose their damping capacity over time due to environmental or dynamic effects.This deterioration of them requires the determination of the maintenance and repair needs and is important for the long-termisolator life.In this study,an artificial intelligence prediction model has been developed to determine the damage and maintenance-repair requirements of isolators as a result of environmental effects and dynamic factors over time.With the developed model,the required damping capacity of the isolator structure was estimated and compared with the previously placed isolator capacity,and the decrease in the damping property was tried to be determined.For this purpose,a data set was created by collecting the behavior of structures with single degrees of freedom(SDOF),different stiffness,damping ratio and natural period isolated from the foundation under far fault earthquakes.The data is divided into 5 different damping classes varying between 10%and 50%.Machine learning model was trained in damping classes with the data on the structure’s response to random seismic vibrations.As a result of the isolator behavior under randomly selected earthquakes,the recorded motion and structural acceleration of the structure against any seismic vibration were examined,and the decrease in the damping capacity was estimated on a class basis.The performance loss of the isolators,which are separated according to their damping properties,has been tried to be determined,and the reductions in the amounts to be taken into account have been determined by class.In the developed prediction model,using various supervised machine learning classification algorithms,the classification algorithm providing the highest precision for the model has been decided.When the results are examined,it has been determined that the damping of the isolator structure with the machine learning method is predicted successfully at a level exceeding 96%,and it is an effective method in deciding whether there is a decrease in the damping capacity.