A finite element calculation model of corroded RC eccentric compressive members was build using finite element software ANSYS. The model considers the decline of mechanical properties and the effective section of a co...A finite element calculation model of corroded RC eccentric compressive members was build using finite element software ANSYS. The model considers the decline of mechanical properties and the effective section of a corroded steel bar,as well as the deterioration of bond character between corroded reinforcement and concrete. The reliability of the finite element model was evaluated by comparing the results of the finite element calculation with the data from experiments. Based on the finite element analysis results,the influence of corrosion degree,the diameter change of the longitudinal reinforcing bars and the spacing change of stirrups on the flexural stiffness were calculated and analyzed.展开更多
This paper presents the application of anisotropic damage theory to the study of forming limit diagram of A12024T3 aluminum alloy sheet. In the prediction of limiting strains of the aluminum sheet structure, a finite ...This paper presents the application of anisotropic damage theory to the study of forming limit diagram of A12024T3 aluminum alloy sheet. In the prediction of limiting strains of the aluminum sheet structure, a finite element cell model has been constructed. The cell model consists of two phases, the aluminum alloy matrix and the intermetallic cluster. The material behavior of the aluminum alloy matrix is described with a fully coupled elasto-plastic damage constitutive equation. The intermetallic cluster is assumed to be elastic and brittle. By varying the stretching ratio, the limiting strains of the sheet under biaxial stretching have been predicted by using the necking criterion proposed. The prediction is in good agreement with the experimental findings. Moreover, the finite element cell model can provide information for understanding the microscopic damage mechanism of the aluminum alloy. Over-estimation of the limit strains may result if the effect of material damage is ignored in the sheet metal forming study.展开更多
This study aims to numerically and experimentally investigate the response of a medium strength rock material under unconfined compression loading up to failure. The unconfined compressive strength(UCS) is one of the ...This study aims to numerically and experimentally investigate the response of a medium strength rock material under unconfined compression loading up to failure. The unconfined compressive strength(UCS) is one of the most important parameters in characterising rock material behaviour. Hence the UCS is crucial in understanding the failure mechanism of fractured rocks. An effective approach to determine the UCS and to investigate the behaviours of rock materials under unconfined compression is essential in the majority of research fields of rock mechanics. The experimental configuration for the unconfined compression test, suggested by the protocols of the ASTM standard, has some limitations which affect the accuracy in determination of the real UCS. Among several alternative configurations proposed, the Mogi’s configuration seems to be the most appropriate one. Therefore, the ASTM and Mogi’s configurations were used to perform the tests on a medium strength rock material, i.e. Pietra Serena sandstone. The results using two configurations were discussed in terms of the differences. The tests were also replicated in LSDYNA using a finite element method(FEM) coupled smooth particle hydrodynamics(SPH) technique.This technique is employed in this study due to its capabilities to cope with large deformation issues related to the rocks. An advanced material model, called the Karagozian and Case Concrete(KCC) model,is implemented in the numerical simulations. The KCC model consists of three independent fixed failure surfaces and it can consider the damage accumulation based on the current state of stress among these failure surfaces. An equation-of-state(EOS) is used in conjunction with KCC material model for decoupling the volumetric and deviatoric responses. The numerical and experimental results were finally compared with the focus on the stress-strain diagram and the failure patterns. The comparison shows that the numerical results are in good agreement with the experimental results.展开更多
基金The National Natural Science Foundation of China (No.50578068)
文摘A finite element calculation model of corroded RC eccentric compressive members was build using finite element software ANSYS. The model considers the decline of mechanical properties and the effective section of a corroded steel bar,as well as the deterioration of bond character between corroded reinforcement and concrete. The reliability of the finite element model was evaluated by comparing the results of the finite element calculation with the data from experiments. Based on the finite element analysis results,the influence of corrosion degree,the diameter change of the longitudinal reinforcing bars and the spacing change of stirrups on the flexural stiffness were calculated and analyzed.
基金Project supported by the Research Committee of The Hong Kong Polytechnic University (No.G-YX34).
文摘This paper presents the application of anisotropic damage theory to the study of forming limit diagram of A12024T3 aluminum alloy sheet. In the prediction of limiting strains of the aluminum sheet structure, a finite element cell model has been constructed. The cell model consists of two phases, the aluminum alloy matrix and the intermetallic cluster. The material behavior of the aluminum alloy matrix is described with a fully coupled elasto-plastic damage constitutive equation. The intermetallic cluster is assumed to be elastic and brittle. By varying the stretching ratio, the limiting strains of the sheet under biaxial stretching have been predicted by using the necking criterion proposed. The prediction is in good agreement with the experimental findings. Moreover, the finite element cell model can provide information for understanding the microscopic damage mechanism of the aluminum alloy. Over-estimation of the limit strains may result if the effect of material damage is ignored in the sheet metal forming study.
文摘This study aims to numerically and experimentally investigate the response of a medium strength rock material under unconfined compression loading up to failure. The unconfined compressive strength(UCS) is one of the most important parameters in characterising rock material behaviour. Hence the UCS is crucial in understanding the failure mechanism of fractured rocks. An effective approach to determine the UCS and to investigate the behaviours of rock materials under unconfined compression is essential in the majority of research fields of rock mechanics. The experimental configuration for the unconfined compression test, suggested by the protocols of the ASTM standard, has some limitations which affect the accuracy in determination of the real UCS. Among several alternative configurations proposed, the Mogi’s configuration seems to be the most appropriate one. Therefore, the ASTM and Mogi’s configurations were used to perform the tests on a medium strength rock material, i.e. Pietra Serena sandstone. The results using two configurations were discussed in terms of the differences. The tests were also replicated in LSDYNA using a finite element method(FEM) coupled smooth particle hydrodynamics(SPH) technique.This technique is employed in this study due to its capabilities to cope with large deformation issues related to the rocks. An advanced material model, called the Karagozian and Case Concrete(KCC) model,is implemented in the numerical simulations. The KCC model consists of three independent fixed failure surfaces and it can consider the damage accumulation based on the current state of stress among these failure surfaces. An equation-of-state(EOS) is used in conjunction with KCC material model for decoupling the volumetric and deviatoric responses. The numerical and experimental results were finally compared with the focus on the stress-strain diagram and the failure patterns. The comparison shows that the numerical results are in good agreement with the experimental results.
