Joint torque-based Cartesian impedance control with friction compensations

In order to investigate the joint torque-based Cartesian impedance control strategies and the influence of compensations for friction, an experimental study on the identification of friction parameters, friction compensation and the Cartesian impedance control are developed for the harmonic drive robot, by using the sensors available in the joint itself. Different from the conventional Cartesian impedance control schemes which are mostly based on the robot end force/torque information, five joint torque-based Cartesian impedance control schemes are considered, including the force-based schemes in Cartesian/joint space, the position-based schemes in Cartesian/joint space and the stiffness control. Four of them are verified by corresponding experiments with/without friction compensations. By comparison, it is found that the force-based impedance control strategy is more suitable than the position-based one for the robot based on joint torque feedback and the friction has even a positive effect on Cartesian impedance control stability.

Effects of Joint Controller on Analytical Modal Analysis of Rotational Flexible Manipulator

Modal analysis is a fundamental and important task for modeling and control of the flexible manipulator. However, almost all of the traditional modal analysis methods view the flexible manipulator as a pure mechanical structure and neglect feedback action of joint controller. In order to study the effects of joint controller on the modal analysis of rotational flexible manipulator, a closed-loop analytical modal analysis method is proposed. Firstly, two exact boundary constraints, namely servo feedback constraint and bending moment constraint, are derived to solve the vibration partial differential equation. It is found that the stiffness and damping gains of joint controller are both included in the boundary conditions, which lead to an unconventional secular term. Secondly, analytical algorithm based on Ritz approach is developed by using Laplace transform and complex modal approach to obtain the natural frequencies and mode shapes. And then, the numerical simulations are performed and the computational results show that joint controller has pronounced influence on the modal parameters： joint controller stiffness reduces the natural frequency, while joint controller damping makes the shape phase non-zero. Furthermore, the validity of the presented conclusion is confirmed through experimental studies. These findings are expected to improve the performance of dynamics simulation systems and model-based controllers.

Dynamic surface control-backstepping based impedance control for 5-DOF flexible joint robots

A new impedance controller based on the dynamic surface control-backstepping technique to actualize the anticipant dynamic relationship between the motion of end-effector and the external torques was presented. Comparing with the traditional backstepping method that has ＂explosion of terms＂ problem, the new proposed control system is a combination of the dynamic surface control technique and the backstepping. The dynamic surface control （DSC） technique can resolve the ＂explosion of terms＂ problem that is caused by differential coefficient calculation in the model, and the problem can bring a complexity that will cause the backstepping method hardly to be applied to the practical application, especially to the multi-joint robot. Finally, the validity of the method was proved in the laboratory environment that was set up on the 5-DOF （degree of freedom） flexible joint robot. Tracking errors of DSC-backstepping impedance control that were 2.0 and 1.5 mm are better than those of backstepping impedance control which were 3.5 and 2.5 mm in directions X, Y in free space, respectively. And the anticipant Cartesian impedance behavior and compliant behavior were nchieved successfully as depicted theoretically.

Integrated design of brushless motor drive and control system for robot joints

To meet the requirements of high performance, low cost, and easy operation of the robot, a brushless motor drive and control system for the robot joint is designed, including CAN bus, WPF upper host computer development, and magnetic encoders, and other sensors, in which the STM32 F103 chip is used as the main control chip, and the DRV8323 is a brushless motor drive chip. The principle of field-oriented control(FOC) brushless motor drive is elaborated.Meanwhile, the drive and control system design is completed from both hardware and software aspects. Finally, the PID algorithm is used for the closed-loop speed test of the robot joint. The experimental result shows that the designed robot joints and control system run smoothly and reliably, have the characteristics of modularization and miniaturization, and are suitable for the control of micro-service robots and manipulators.

MODELING AND CONTROLLING OF PARALLEL MANIPULATOR JOINT DRIVEN BY PNEUMATIC MUSCLES

A parallel manipulator joint driven by three pneumatic muscles and its posture control strategy are presented. Based on geometric constraints and dynamics, a system model is developed through which some influences on dynamic response and open-loop gain are analyzed including the supply pressure, the initial pressure and the volume of pneumatic muscle. A sliding-mode controller with a nonlinear switching function is applied to control posture, which adopts the combination of a main method that separates control of each muscle and an auxiliary method that postures error evaluation of multiple muscles, especially adopting the segmented and intelligent adjustments of sliding-mode parameters to fit different expected postures and initial states. Experimental results show that this control strategy not only amounts to the steady-state error of 0. 1° without overshoot, but also achieves good trajectory tracking.

Unified Vibration Suppression and Compliance Control for Flexible Joint Robot

An adaptive control scheme is presented,which can simultaneously realize vibration suppression and compliance control for flexible joint robot(FJR).The proposed control scheme provides a unified formulation for both vibration suppression mode,where FJR tracks the desired position with little vibration,and compliance mode,in which FJR presents passive.Instead of designing multiple controllers and switching between them,both modes are integrated into a single controller,and the transition between two modes is smooth and stable.The stability of the closed-loop system is theoretically proven via the Lyapunov method,with the considering the dynamics uncertainties in both link side and motor side.Simulation results are presented to illustrate good performances of the proposed control scheme.

Nonlinear Modeling and Identification of Structural Joint by Response Control Vibration Test

Components of mechanical product are assembled by structural joints,such as bolting,riveting,welding,etc.Structural joints introduce nonlinearity to some engineering structures,and the nonlinearity need to be modeled precisely.To meet serious quality requirements,it is necessary to detect and identify nonlinearity of mechanical products for structural optimization.Modal test to acquire a dynamic response has been applied for decades,which provides reliable results for finite element(FE)model updating.Here response control vibration test for identification of nonlinearity is presented.A nonlinear system can be regarded as linearity for particular steady state response,and classical linear analysis tool is applicable to extract modal data for particular response.First,its applicability is illustrated by some numerical simulations.Subsequently,it is implemented on experimental setup with structural joints by shaking table.The stiffness and damping function dependent of relative displacement are fitted to describe its inherent nonlinearity.The spring and damping forces are identified by harmonic balance method(HBM)to predict output response.Based on the identified results,the procedure is recommended that it allows a reliable measurement of nonlinearity with a certain accuracy.

Design of Robust Controller for Flexible Joint Robot with Nonlinear Friction Characteristics

A robust controller method for flexible joint robot considering the effect caused by nonlinear friction was presented.The nonlinear friction was denoted as inverse additive output uncertainty relative to the nominal model in our work,based on which the describing function was analyzed in frequency domain,and the weighting function of nonlinear friction was further calculated as well. By combining the friction uncertainty,the mixed sensitivity H∞optimization was proposed as the benchmark for controller design, which also leaded to good performance of robustness. Furthermore,unstructured perturbation to the system was analyzed so that the stability was guaranteed. Simulation results show that the proposed controller can provide excellent tracking and regulation performance.

Distinct element modelling of fracture plan control in continuum and jointed rock mass in presplitting method of surface mining

Controlled blasting techniques are used to control overbreak and to aid in the stability of the remaining rock formation. Presplitting is one of the most common methods which is used in many open pit mining and surface blast design. The purpose of presplitting is to form a fracture plane across which the radial cracks from the production blast cannot travel. The purpose of this study is to investigate of effect of presplitting on the generation of a smooth wall in continuum and jointed rock mass. The 2D distinct element code was used to simulate the presplitting in a rock slope. The blast load history as a function of time was applied to the inner wall of each blasthole. Important parameters that were considered in the analysis were stress tensor and fracturing pattern. The blast loading magnitude and blasthole spacing and jointing pattern were found to be very significant in the final results.

Fractional Order Linear Active Disturbance Rejection Control for Linear Flexible Joint System

A linear flexible joint system using fractional order linear active disturbance rejection control is studied in this paper.With this control scheme,the performance against disturbances,uncertainties,and attenuation is enhanced.Linear active disturbance rejection control(LADRC)is mainly based on an extended state observer(ESO)technology.A fractional integral(FOI)action is combined with the LADRC technique which proposes a hybrid control scheme like FO-LADRC.Incorporating this FOI action improves the robustness of the standard LADRC.The set-point tracking of the proposed FO-LADRC scheme is designed by Bode’s ideal transfer function(BITF)based robust closed-loop concept,an appropriate pole placement method.The effectiveness of the proposed FO-LADRC scheme is illustrated through experimental results on the linear flexible joint system(LFJS).The results show the enhancement of the robustness with disturbance rejection.Furthermore,a comparative analysis is presented with the results obtained using the integer-order LADRC and FO-LADRC scheme.

Research on Direct Yaw Moment Control Strategy of Distributed-Drive Electric Vehicle Based on Joint Observer

Combined with the characteristics of the distributed-drive electric vehicle and direct yaw moment control,a double-layer structure direct yaw moment controller is designed.The upper additional yaw moment controller is constructed based on model predictive control.Aiming at minimizing the utilization rate of tire adhesion and constrained by the working characteristics of motor system and brake system,a quadratic programming active set was designed to optimize the distribution of additional yaw moments.The road surface adhesion coefficient has a great impact on the reliability of direct yaw moment control,for which joint observer of vehicle state parameters and road surface parameters is designed by using unscented Kalman filter algorithm,which correlates vehicle state observer and road surface parameter observer to form closed-loop feedback correction.The results show that compared to the“feedforward+feedback”control,the vehicle’s error of yaw rate and sideslip angle by the model predictive control is smaller,which can improve the vehicle stability effectively.In addition,according to the results of the docking road simulation test,the joint observer of vehicle state and road surface parameters can improve the adaptability of the vehicle stability controller to the road conditions with variable adhesion coefficients.

Joint space compliance control for a hydraulic quadruped robot based on force feedback

In the realm of quadruped robot locomotion,compliance control is imperative to handle impacts when negotiating unstructured terrains.At the same time,kinematic tracking accuracy should be guaranteed during locomotion.To meet both demands,ajoint space compliance controller is designed,so that compliance can be achieved in stance phase while position tracking performance can be guaranteed in swing phase.Unlike operational space compliance control,the joint space compliance control method is easy to implement and does not depend on robot dynamics.As for each joint actuator,high performance force control is of great importance for compliance design.Therefore,a nonlinear PI controller based on feedback linearization is proposed for the hydraulic actuator force control.Besides,an outer position loop（compliance loop）is closed for each joint.Experiments are carried out to verify the force controller and compliance of the hydraulic actuator.The robot leg compliance is assessed by a virtual prototyping simulation.

Joint Resource Allocation and Admission Control Mechanism in Software Defined Mobile Networks

This paper presented a joint resource allocation(RA) and admission control(AC) mechanism in software defined mobile networks(SDMNs). In this mechanism, the joint RA and AC problem can be formulated as an optimization problem with the aim of maximizing the number of admitted users while simultaneously minimizing the number of allocated channels. Since the primal problem is modeled to be a mixed integer nonlinear problem(MINLP), we attain the suboptimal solutions to the primal MINLP by convex relaxation. Additionally, with the global information collected by the SDMNs controller, a centralized joint RA and AC(CJRA)algorithm is proposed by the Lagrange dual decomposition technique to obtain the global optimum. Meanwhile, we propose an OpenFlow rules placement strategy to realize CJRA in an efficient way. Moreover, a distributed algorithm is also developed to find the local optimum, showing a performance benchmark for the centralized one. Finally, simulation results show that the proposed centralized algorithm admits more users compared with the distributed.

Gas dynamic control of properties of welded joints from high strength alloyed steels

Gas dynamic control in welding with consumable electrode in conditions of two-jet gas shielding and its impact on the processes in the welding area and properties of the welded joints from high strength alloyed steel 30HGSA is considered in the paper. The results of a comparative experimental study of controlling the properties of welded joints by changing the gas dynamics of the active shielding gas are given. The impact force of a shielding gas jet on the drop of the electrode metal is 12 times higher in conditions of two-jet gas shielding than in those of single jet shielding. It is found that gas dynamics of the active shielding gas jet determines the formation of the welded joints, their chemical properties and the properties of the welded joints from high strength alloyed steels. The consumable electrode welding method with two-jet gas shielding provides controlled dynamics in the welding area and allows controlling the transfer of the electrode metal, chemical composition of the weld, stabilizing the welding process, it ensures higher mechanical properties of the welded joints.

Trajectory tracking control of the bionic joint of the musculoskeletal leg mechanism

Pneumatic artificial muscles(PAMs) have properties similar to biological muscles,which are widely used in robotics as actuators.It is difficult to achieve high-precision position control for robotics system driven by PAMs.A 3-DOF musculoskeletal bionic leg mechanism is presented,which is driven by PAMs for quadruped robots.PAM is used to simulate the compliance of biological muscle.The kinematics of the leg swing is derived,and the foot desired trajectory is planned as the sinusoidal functions.The swing experiments of the musculoskeletal leg mechanism are conducted to analyse the extension and flexion of joints.A proportional integral derivative(PID) algorithm is presented for controlling the flexion/extension of the joint.The trajectory tracking results of joints and the PAM gas pressure are obtained.Experimental results show that the developed leg mechanism exhibits good biological properties.

Diagnostic Sacroiliac Joint Injections: Is a Control Block Necessary?

Background: Sacroiliac joint (SIJ) pain presents as a deep and somatic pain, predominantly affecting the lower back and buttock and referring down the leg, sometimes as far as the foot. Given that the features of SIJ pain are non-specific and that this referred pain is similar to lumbar facet joint and lumbar disc pain, diagnostic local anesthetic injections (diagnostic blocks) into the SIJ are used to identify the source of pain. Despite wide use, little is known about the false positive rate of a single diagnostic sacroiliac (SI) block and the requirement for a control block. Objective: To determine whether a control SI block is necessary and to monitor the false positive rate for a single injection. Study Design: A prospective and observational study was conducted as part of a practice audit, with data collected over 3.5 years at the authors’ private practice. Patients & Methods: Under fluoroscopic guidance, 1408 consecutive patients presenting with prominent deep somatic pain over the SIJ region were sterilely injected with anesthetic into the SIJ and/or the deep interosseous ligament (DIL). Pain was measured on the 11-point Numerical Rating Scale (NRS) prior to injection and incrementally over the following 1- 2 weeks. Fully completed and unequivocal data sets were available for 1060 patients. Decreases in pain scores (of >80%) at >2 hours of post-injection were indicative of SIJ pain and recorded as a positive SIJ block. Results: Of 1060 patients receiving a first SIJ diagnostic block, 680 (64.1%) recorded a positive result. Subsequently, 271 positive patients and 22 who were negative for SIJ pain opted to receive a second control block. SIJ pain diagnosis was confirmed in 237/271 (87.5%) of those with an initial positive response, while 18/22 patients (81%) had their initial negative result confirmed. The false positive rate of a single block is therefore calculated at 12.5%, and on a contingency table analysis, a single anesthetic SIJ injection has diagnostic accuracy of 87.03%, with high sensitivity (98.3%), when compared with a second control diagnostic block. Limitations: All injections were performed at one clinical centre. A proportion (348/1408) of initial patients did not return fully completed pain records or had equivocal responses (≥80% pain relief, but transiently, for ≤30 min) and were excluded from further analysis. Conclusion: Given the observed high rates of accuracy in this study, it is reasonable to suggest the use of one diagnostic block as the criterion standard for assessing the SIJ as the source of a patient’s pain.

A novel adaptive joint power control algorithm with channel estimation in a CDMA cellular system

Joint power control has advantages of multi-user detection and power control; and it can combat the multi-access interference and the near-far problem. A novel adaptive joint power control algorithm with channel estimation in a CDMA cellular system was designed. Simulation results show that the algorithm can control the power not only quickly but also precisely with a time change. The method is useful for increasing system capacity.

Design of cost allocation rule for joint replenishment with controllable lead time

To encourage retailers to form cooperative alliances to jointly replenish inventory,considering that the supplier provides a flexible lead time and quantity discount to retailers,a model of average total cost per unit time of periodic joint replenishment is constructed,and an approximate algorithm,which can satisfy the requirement of any given precision,is given.The cost allocation rule in the core of the joint replenishment game is designed based on the cooperative game theory.The numerical experiment results show that the proposed algorithm can quickly solve the joint replenishment problem when the item number is not greater than 640.The retailer's cost saving rate is always greater than 0,and it increases with the increase in quantity discount and fixed cost after adopting the given cost allocation rule.With the increase in the safety stock level,the retailer's cost saving rate increases first and then decreases;and the retailer's cost saving rate increases with the increase in the size of the alliance,but it decreases as the number of product category increases.The proposed cost allocation rule can reduce the retailer's cost up to 20%,which is conducive to forming a cooperative coalition.

Research on Precision Assembly Robot's Joint Torque Control Based on Current Measurement

A set of new current sensing device is used to realize joint torque control based on current measurement in a precision assembly robot's third joint. The output torque's model of the joint's brushless DC motor is founded. Disturbance factors and the compensated effect of the torque's closed loop based on current measurement are analyzed. Related simulations and experiments show that the system has good current tracking and anti-disturbances performance, which improve the force control performance of the robot in assembly.

The Design of Control System for Multi Joint Robot based on PC+DSP

A multi joint robot control system was designed based on the universal processor PC+DSP in order to overcome the short- comings of the control system in terms of flexibility, cost performance, and software transplantation, which use Industrial Personal Computer for the upper monitor and MAC Motion control card for the lower computer. The design of multi joint robot control system is accomplished through hardware circuit design, VC++ programming and so on. Finally, six joint robot platform is used to test the control performance,The results show that the designed control system has the advantages of flexible fimction,easy expansion and easy porting of software.