Mechanical responses of underground carriageway structures due to construction of metro tunnels beneath the existing structure:A case study

To understand the mechanical response pattern of the existing structure and ground due to the construction of metro tunnels underneath,the finite difference method is adopted to study the torsional deformation and stress variation of the existing structure and the effect of underground carriageway structures on the surface subsidence.The curves of the maximum differential subsidence,torsion angle,and distortion of the cross-section of the existing structure show two peaks in succession during traversing of two metro tunnels beneath it.The torsion angle of the existing structure changes when the two tunnels traverse beneath it in opposite directions.The first traversing of the shield tunnel mainly induces the magnitude variation in torsional deformation of the existing structure,but the second traversing of the subsurface tunnel may cause a dynamic change in the magnitude and form of torsional deformation in the existing structure.The shielding effect can reduce the surface subsidence caused by metro tunnel excavation to a certain extent,and the development trend of subsidence becomes slower as the excavation continues.

Numerical analysis on seismic performance of underground structures in liquefiable interlayer sites from centrifuge shaking table test

When an underground structure passes through a liquefiable soil layer,the soil liquefaction may pose a significant threat to the structure.A centrifuge shaking table test was performed to research the seismic response of underground structures in liquefiable interlayer sites,and a valid numerical model was obtained through simulation model test.Finally,the calibrated numerical model was used to perform further research on the influence of various distribution characteristics of liquefiable interlayers on the seismic reaction of underground structures.The key findings are as follows.The structure faces the most unfavorable condition once a liquefiable layer is located in the middle of the underground structure.When a liquefiable layer exists in the middle of the structure,the seismic reactions of both the underground structure and model site will increase with the rise of the thickness of the liquefiable interlayer.The inter-story drift of the structure in the non-liquefiable site is much smaller than that in the liquefiable interlayer site.The inter-story drift of the structure is not only associated with the site displacement and the soil-structure stiffness ratio but also closely associated with the slippage of the soil-structure contact interface under the condition of large deformation of the site.

Discussion on Structural Health Monitoring of Urban Underground Road Tunnel

The number of urban underground road tunnels in China is increasing year by year,and health monitoring of tunnels is an effective management method to ensure their structural integrity.However,for shorter underground road tunnel projects,insufficient investment often leads to less frequent application of health monitoring systems.The application of intelligent structural health monitoring means can not only reduce the project cost but also help workers fully understand the actual situation of the tunnel structure.Therefore,this paper analyzes the characteristics,problems,and design of the urban underground road tunnel structural health monitoring system,and discusses the implementation of the urban underground road tunnel structural health monitoring system.

Generalized response displacement methods for seismic analysis of underground structures with complex cross section

The response displacement method(RDM)is recommended for the seismic analysis of underground structures in the transverse direction for many codes,including bases for design of structures-seismic actions for designing geotechnical works(ISO 23469)and code for seismic design of urban rail transit structures(GB 50909-2014).However,there are some obvious limitations in the application of RDM.Springs and the shear stress of the soil could be approximately evaluated for the structures having a simple cross section,such as rectangular and circular structures.It is necessary to propose simplified seismic analysis methods for structures with complex cross sections.This paper refers to the idea of RDM and proposes three generalized response displacement methods(GRDM).In GRDM1,a part of the soil surrounding a structure is selected to generate a generalized underground structure with a rectangular cross section,and the same analysis model as RDM is applied to analyze the responses of the structure.In GRDM2,a hollow soil model without a generalized structure is used to compute the equivalent load caused by the relative displacement of the soil,and the soil-structure interaction model is applied to calculate the responses of the structure.In GRDM3,a continuous soil model is applied to compute the equivalent load caused by the relative displacement and shear stress of the soil,and the soil-structure interaction model is applied to analyze the responses of the structure,which is the same as the model used in GRDM2.The time-history analysis method(THAM)is used to evaluate the accuracy of the proposed simplified methods.Results show that the error of GRDM1 is about 20%,while the error is only 5%for GRDM2 and GRDM3.Among the three proposed methods,GRDM3 has obvious advantages regarding calculation efficiency and accuracy.Therefore,it is recommended to use GRDM3 for the seismic response analysis of underground structures that have conventional simple or complex cross sections.

Rock mass structural recognition from drill monitoring technology in underground mining using discontinuity index and machine learning techniques

A procedure to recognize individual discontinuities in rock mass from measurement while drilling(MWD)technology is developed,using the binary pattern of structural rock characteristics obtained from in-hole images for calibration.Data from two underground operations with different drilling technology and different rock mass characteristics are considered,which generalizes the application of the methodology to different sites and ensures the full operational integration of MWD data analysis.Two approaches are followed for site-specific structural model building:a discontinuity index(DI)built from variations in MWD parameters,and a machine learning(ML)classifier as function of the drilling parameters and their variability.The prediction ability of the models is quantitatively assessed as the rate of recognition of discontinuities observed in borehole logs.Differences between the parameters involved in the models for each site,and differences in their weights,highlight the site-dependence of the resulting models.The ML approach offers better performance than the classical DI,with recognition rates in the range 89%to 96%.However,the simpler DI still yields fairly accurate results,with recognition rates 70%to 90%.These results validate the adaptive MWD-based methodology as an engineering solution to predict rock structural condition in underground mining operations.

An improved pseudo-static method for seismic resistant design of underground structures

This paper describes a commonly used pseudo-static method in seismic resistant design of the cross section of underground structures. Based on dynamic theory and the vibration characteristics of underground structures, the sources of errors when using this method are analyzed. The traditional seismic motion loading approach is replaced by a method in which a one-dimensional soil layer response stress is differentiated and then converted into seismic live loads. To validate the improved method, a comparison of analytical results is conducted for internal forces under earthquake shaking of a typical shallow embedded box-shaped subway station structure using four methods： the response displacement method, finite element response acceleration method, the finite element dynamic analysis method and the improved pseudo-static calculation method. It is shown that the improved finite element pseudo-static method proposed in this paper provides an effective tool for the seismic design of underground structures. The evaluation yields results close to those obtained by the finite element dynamic analysis method, and shows that the improved finite element pseudo-static method provides a higher degree of precision.

Fully fluid-solid coupling dynamic model for seismic response of underground structures in saturated soils

The seismic response characteristics of underground structures in saturated soils are investigated.A fully fluid-solid coupling dynamic model is developed and implemented into ABAQUS with a user-defined element to simulate the dynamic behavior of saturated soils.The accuracy of the model is validated using a classic example in literature.The performance of the model is verified by its application on simulating the seismic response characteristics of a subway station built in saturated soils.The merits of the model are demonstrated by comparing the difference of the seismic response of an underground structure in saturated soils between using the fully coupling model and a single-phase medium model.The study finds that the fully coupling model developed herein can simulate the dynamic response characteristics of the underground structures in saturated soils with high accuracy.The seismic response of the underground structure tends to be underestimated by using the single-phase medium model compared with using the fully coupling model,which provides a weaker confining action to the underground structure.

Effects of Long-term Fertilization on Soil M icrobial Com m unity Structure,Labile Organic Carbon and Nitrogen and Enzym e Activity in Paddy Field and Upland

To investigate the effects of long-term fertilization systems on soil microbial community structure,labile organic carbon and nitrogen and enzyme activity in yellow sand paddy field and upland,a field experiment was conducted at the experimental station of Dongyang Institute of Maize Research in Zhejiang Province,China in 2009.The experiment consisted of six treatments with three replicates,and they were arranged in a completely randomized design,including no fertilization in paddy field (PCK),conventional fertilization in paddy field (PCF),formulated fertilization by soil testing in paddy field (PSTF),formulated fertilization by soil testing with organic manure in paddy field (PSTF+OF),conventional fertilization on upland (DCF),and formulated fertilization by soil testing with organic manure on upland (DSTF+OF).Soil nutrients,enzyme activity,microbial biomass and community structure were determined in 2015.The results showed that compared with no fertilization in paddy field (PCK),fertilization increased soil phosphorus and potassium content,and decreased pH value.No fertilization in paddy field (PCK) had no significant effect on soil culturable microorganisms in paddy field and upland,but formulated fertilization by soil testing with organic manure on upland (DSTF+OF) significantly increased the number of fungi.Formula fertilization by soil testing with organic manure (PSTF+OF) also significantly increased soil microbial biomass carbon and nitrogen in paddy field and upland.Moreover,fertilization had no significant effect on soil cellulase activity,but formula fertilization by soil testing with organic manure (PSTF+OF) significantly increased soil dehydrogenase and catalase activity.Therefore,long-term application of chemical fertilizer with organic fertilizer can effectively improve soil fertility.

DYNAMIC LOAD ANALYSIS OF UNDERGROUND STRUCTURE UNDER EFFECT OF BLAST WAVE

A semi-analytical method of solving the problem of dynamic stress concentration of arbitrary underground structure under the effect of blast waves was introduced. Using the Fourier transform theory, the shock waves （in the forms of SH-waves） can be converted into frequency bands. After employing complex functions and conformal mapping, the admittance functions of various underground structures were obtained. Then, the problem of the time domain dynamic stress response of underground structure can be easily solved through the Fourier inverse transform. At last, the results and curves of the dynamic stress for the square, triangle and horseshoe cavity were presented.

Problems of durability and reinforcement measures for underground structures in China

In this paper, the bolt- and cable-supported structures mainly refer to anchored cables, anchored bolts, soil nails and other commonly used reinforcing and supporting structures in geotechnical engineering, as well as reinforced soil structures in permanent works. They are often used in combination, or formed into composite bolt-and cable-supported structures, with other traditional construction methods and relevant measures. Distinct characteristics of such structures are that they are most often invisible, exposed to more severe underground corrosive environments and with strict durability requirements. A number of serious durability problems of underground structures are discussed and major achievements and advances in China and abroad in terms of durability and reinforcement measures for underground structures are reviewed, followed by comprehensive analyses. Some suggestions for those problems are put forward.

FUNDAMENTAL OF DYNAMICAL ANALYSIS OF THE BLAST-RESISTANT UNDERGROUND STRUCTURES

In this paper, the generalized variational principle of dynamic analysis for the blast-resistant underground structures is established, and the corresponding generalized functional of elastoplastic analysis for underground structures is derived, and the generalized variational principle of nonconservative system is given, thus the fundamental of dynamical analysis for underground structures to resist blast is proposed. Finally, for the underground cylindrical structure to resist blast, dynamical calculations are made, and compared with the test results.

CONSTRUCTION OF UNDERGROUND HYDRAULIC STRUCTURES AND TBM TECHNOLOGY IN CHINA

This paper deals with the construction of underground hydraulic structures and TBM technology in China——past,present and future. China ranks number one in the world in water power. But,the ratio of developed to potential hydropower is only about 20%. The exploitable water power in West China,where is featured by high mountain and complex geology,accounts for 83% of the total for China. Most of the project structures have to be located underground. The projected length of hydraulic underground openings per year is about 180 km. Several underground projects completed,under execution and planned are highlighted in this paper. Finally,general information about the development of TBM technology in hydraulic construction in China is outlined.

Modularized and Parametric Modeling Technology for Finite Element Simulations of Underground Engineering under Complicated Geological Conditions

The surrounding geological conditions and supporting structures of underground engineering are often updated during construction,and these updates require repeated numerical modeling.To improve the numerical modeling efficiency of underground engineering,a modularized and parametric modeling cloud server is developed by using Python codes.The basic framework of the cloud server is as follows:input the modeling parameters into the web platform,implement Rhino software and FLAC3D software to model and run simulations in the cloud server,and return the simulation results to the web platform.The modeling program can automatically generate instructions that can run the modeling process in Rhino based on the input modeling parameters.The main modules of the modeling program include modeling the 3D geological structures,the underground engineering structures,and the supporting structures as well as meshing the geometric models.In particular,various cross-sections of underground caverns are crafted as parametricmodules in themodeling program.Themodularized and parametric modeling program is used for a finite element simulation of the underground powerhouse of the Shuangjiangkou Hydropower Station.This complicatedmodel is rapidly generated for the simulation,and the simulation results are reasonable.Thus,this modularized and parametric modeling program is applicable for three-dimensional finite element simulations and analyses.

Combined use of fly ash and silica to prevent the long-term strength retrogression of oil well cement set and cured at HPHT conditions

The long-term strength retrogression of silica-enriched oil well cement poses a significant threat to wellbore integrity in deep and ultra-deep wells, which is a major obstacle for deep petroleum and geothermal energy development. Previous attempts to address this problem has been unsatisfactory because they can only reduce the strength decline rate. This study presents a new solution to this problem by incorporating fly ash to the traditional silica-cement systems. The influences of fly ash and silica on the strength retrogression behavior of oil well cement systems directly set and cured under the condition of 200°C and 50 MPa are investigated. Test results indicate that the slurries containing only silica or fly ash experience severe strength retrogression from 2 to 30 d curing, while the slurries containing both fly ash and silica experience strength enhancement from 2 to 90 d. The strength test results are corroborated by further evidences from permeability tests as well as microstructure analysis of set cement. Composition of set cement evaluated by quantitative X-ray diffraction analyses with partial or no known crystal structure(PONKCS) method and thermogravimetry analyses revealed that the conversion of amorphous C-(A)-S-H to crystalline phases is the primary cause of long-term strength retrogression.The addition of fly ash can reduce the initial amount of C-(A)-S-H in the set cement, and its combined use with silica can prevent the crystallization of C-(A)-S-H, which is believed to be the working mechanism of this new admixture in improving long-term strength stability of oil well cement systems.

Analysis of Interf acial Zone Properties and Permeability of Concrete in Underground Structure

Chloride diffusion coefficient and water penetration depth of 3 types concrete were studied. The experimental results show that the concrete permeability decreases itself in the order as follow: pure portland cement concrete(CO), concrete added with fly ash(C1), concrete added with both fly ash and silica fume(C2). SEM and microhardness analyses show that the properties of interfacial zone are significantly influenced by silica fume. With the improvement of interfacial zone properties, the permeability especially the Chloride ion diffusivity of concrete significantly decreases.

Detection of Military Underground Structures through the Remote Sensing Investigation of Phenological Cycle of Crops

This paper aims to explore how field spectroscopy is essential for remote sensing studies for the detection and monitoring of various features such military underground structures in Cyprus. A SVC-HR1024 field spectroradiometer was used and in-band reflectances were determined for medium resolution Landsat-7 ETM satellite sensor, in order to study possible differences of the spectral signature of vegetation throughout the phenological cycle of plant growth. In this study, two test areas were identified, analyzed and modelled: 1) Military Structure Area (MSA) where underground structure exists, and 2) Reference Area (RA) where underground military structure does not exist. The Normalized Difference Vegetation Index (NDVI) was applied to Landsat-7 ETM and Sentinel-2 satellite images in order to identify the presence or absence of underground structures in the study area.

Influence of soil to structure stiffness on the accuracy of the pushover method for underground structures

The pushover method for underground structures is a seismic analysis method featured by high calculation accuracy and a simple implementation process.The method has been widely used in seismic design and other related scientific research;however,the influence of different soil-structure flexibility ratios on the accuracy of this method is still not well understood.In this study,we select the cross-section structures beneath the Daikai subway station as the research object and establish 12 finite element analysis models with different soil-structure flexibility ratios using ABAQUS.All models are computed by the dynamic time-history method or the pushover method.Furthermore,the dynamic time-history solution result is taken as the standard solution,and the precision and application of the pushover analysis method are discussed based on the parameters of peak interlayer displacement and peak internal force of the middle column section.The results show that the soil-structure flexibility ratio has a significant influence on the calculation accuracy of the pushover method,and the calculation accuracy of this method is the most ideal when the soil-structure flexibility is equal to 1.The research results can provide significant references for the seismic design of underground structures or the improvement of simplified seismic analysis methods.

Preface to the special issue on seismic performance of underground structures: From experiments to analysis

Urban underground structures, especially tunnels, subways, and pipeline systems, are all crucial parts of the infrastructure of modern society. By the end of 2021, China had opened rail transit operations in51 cities with a total mileage of 8708 km. Considering their importance for life safety and the economy, appropriate seismic design is of prior necessity.

A comparative analysis of seismic response of shallow buried underground structure under incident P,SV and Rayleigh waves

In this study,A time-domain seismic response analysis method and a calculation model of the underground structure that can realize the input of seismic P,SV and Rayleigh waves are established,based on the viscoelastic artificial boundary elements and the boundary substructure method for seismic wave input.After verifying the calculation accuracy,a comparative study on seismic response of a shallow-buried,double-deck,double-span subway station structure under incident P,SV and Rayleigh waves is conducted.The research results show that there are certain differences in the cross-sectional internal force distribution characteristics of underground structures under different types of seismic waves.The research results show that there are certain differences in the internal force distribution characteristics of underground structures under different types of seismic waves.At the bottom of the side wall,the top and bottom of the center pillar of the underground structure,the section bending moments of the underground structure under the incidences of SV wave and Rayleigh wave are relatively close,and are significantly larger than the calculation result under the incidence of P wave.At the center of the side wall and the top floor of the structure,the peak value of the cross-sectional internal force under the incident Rayleigh wave is larger than the calculation result under SV wave.In addition,the floor of the underground structure under Rayleigh waves vibrates in both the horizontal and vertical directions,and the magnification effect in the vertical direction is more significant.Considering that the current seismic research of underground structures mainly considers the effect of body waves such as the shear waves,sufficient attention should be paid to the incidence of Rayleigh waves in the future seismic design of shallow underground structures.

Seismic performance analysis of underground structures based on random field model of soil mechanical parameters

Soils with spatial variability are the product of natural history.The mechanical properties tested by soil samples from boreholes in the same soil layer may be different.Underground structure service in surrounding soils,their seismic response is controlled by the deformation of the surrounding soils.The variability of soil mechanical parameters was not considered in the current research on the seismic response of underground structures.Therefore,a random field model was established to describe the spatial variability of surrounding soils based on the random field theory.Then the seismic response of underground structures in the random field was simulated based on the time-domain explicit global FEM analysis,and the soil mechanical parameters and earthquake intensity influencing the seismic response of surrounding soils and underground structures were studied.Numerical results presented that,the randomness of soil parameters does not change the plastic deformation mode of surrounding soils significantly.The variation coefficients of inter-story deformation of structures and lateral deformation of columns are much smaller than that of mechanical parameters,and the randomness of soil parameters has no obvious effect on the structural deformation response.