Hierarchical Media Ethics in the Digital Age: An Analysis of the “Primary School Student Lost Homework in Paris” Incident

In the digital age,traditional media ethics norms lack sufficient explanatory power and binding force in practice.This paper uses the“Primary School Student Lost Homework in Paris”incident as a case study to explore the ethical controversies surrounding the dissemination of this event.By adopting a hierarchical media ethics perspective,the paper dynamically examines the ethical conduct of various communicators,elucidates the ethical responsibilities of each party involved,and reveals the complexity of communication ethics in the digital age.

Effects of mechanical vibration on filling and solidification behavior, microstructure and performance of Al/Mg bimetal by lost foam compound casting

Al/Mg bimetal was prepared by lost foam solid-liquid compound casting,and the effects of mechanical vibration on the filling and solidification behavior,microstructure and performance of the bimetal were investigated.Results show that the mechanical vibration has a remarkable influence on the filling and solidification processes.It is found that after mechanical vibration,the filling rate increases and the filling rate at different times is more uniform than that without vibration.In addition,the mechanical vibration also increases the wettability between liquid AZ91D and A356 inlays.The mechanical vibration reduces the horizontal and vertical temperature gradient of the casting and makes the temperature distribution of the whole casting more uniform.Compared to the Al/Mg bimetal without vibration,the shear strength is improved by 39.76%after the mechanical vibration is applied,due to the decrease of the inclusions and Al_(12)Mg_(17) dendrites,and the refinement and uniform distribution of the Mg_(2)Si particles in the interface of the Al/Mg bimetal.

Estimating the Monetary Value of Hours Lost to the Nigerian Public Healthcare System When Full-Time Government Employee Doctors Engage in Dual Practice

Background: Dual Practice (DP) allows full-time public sector doctors to concurrently offer the same clinical services in the private sector. The debate against this practice seems to be largely influenced by its potential to reduce the contracted hours in the public sector and shift attention to private work. Purpose: The purpose of this secondary research is to estimate the monetary value of hours lost to the Nigerian public healthcare system when full-time government employee doctors are engaged in private practice. It attempts to quantify the amount of resource outflow from the public system due to absences and lateness arising from competition for time between the public system’s contracted hours and private practice. Methods: Sensitivity analysis in Excel 2010 was used to calculate doctors’ hourly pay in the public sector using the 2015 Consolidated Medical Salary Structure for medical and dental officers in Nigeria’s federal public service. The parameters used for the calculation were the official 40-hour working week and the average monthly gross pay of doctors on different grade levels. Hypothetical scenarios of hours lost due to absences associated with DP were created. The value of different hypothetical hour losses by the percentage of doctors assumed to engage in dual practice across all doctor grade levels was then computed. Results: The estimated annual value of hours lost from dual practice to a single public tertiary care hospital was N4,851,754 or 15,855 USD (best case scenario) and N19,407,017 or 63,422 USD (worst case scenario) for the normal routine work and N1,800,133 or 5883 USD (best case scenario) and N3,600,266 or 11,766 USD (worst case scenario) for the on-call duty. Conclusion: The government may have been paying salaries for large volumes of work not rendered in the public sector. The overall financial impact of dual practice in the Nigerian public system might be negative.

Oriental Utopia under the Gaze of the Other-A Brief Analysis of the Construction of the Oriental Image in Lost Horizon

Lost Horizon tells a story about Shangri-La,a paradise in the Orient.Throughout the construction of the Oriental image in the novel,it can be found that under its representation of being enslaved,driven,marginalized and silenced,it implies a three-dimensional flow mechanism with multiple power-relationships interwoven between Orient and Occident,insiders and outsiders,“civilized”and“uncivilized”,male and female,etc.Driven by this mechanism,the Oriental image is integrated under a single abstract label,which has become a way for the Occident to re-understand,reconstruct and express itself after the war.

Machine learning for carbonate formation drilling: Mud loss prediction using seismic attributes and mud loss records

Due to the complexity and variability of carbonate formation leakage zones, lost circulation prediction and control is one of the major challenges of carbonate drilling. It raises well-control risks and production expenses. This research utilizes the H oilfield as an example, employs seismic features to analyze mud loss prediction, and produces a complete set of pre-drilling mud loss prediction solutions. Firstly, 16seismic attributes are calculated based on the post-stack seismic data, and the mud loss rate per unit footage is specified. The sample set is constructed by extracting each attribute from the seismic trace surrounding 15 typical wells, with a ratio of 8:2 between the training set and the test set. With the calibration results for mud loss rate per unit footage, the nonlinear mapping relationship between seismic attributes and mud loss rate per unit size is established using the mixed density network model.Then, the influence of the number of sub-Gausses and the uncertainty coefficient on the model's prediction is evaluated. Finally, the model is used in conjunction with downhole drilling conditions to assess the risk of mud loss in various layers and along the wellbore trajectory. The study demonstrates that the mean relative errors of the model for training data and test data are 6.9% and 7.5%, respectively, and that R2is 90% and 88%, respectively, for training data and test data. The accuracy and efficacy of mud loss prediction may be greatly enhanced by combining 16 seismic attributes with the mud loss rate per unit footage and applying machine learning methods. The mud loss prediction model based on the MDN model can not only predict the mud loss rate but also objectively evaluate the prediction based on the quality of the data and the model.

Research progress and development of deep and ultra-deep drilling fluid technology

The research progress of deep and ultra-deep drilling fluid technology systematically reviewed,the key problems existing are analyzed,and the future development direction is proposed.In view of the high temperature,high pressure and high stress,fracture development,wellbore instability,drilling fluid lost circulation and other problems faced in the process of deep and ultra-deep complex oil and gas drilling,scholars have developed deep and ultra-deep high-temperature and high-salt resistant water-based drilling fluid technology,high-temperature resistant oil-based/synthetic drilling fluid technology,drilling fluid technology for reservoir protection and drilling fluid lost circulation control technology.However,there are still some key problems such as insufficient resistance to high temperature,high pressure and high stress,wellbore instability and serious lost circulation.Therefore,the development direction of deep and ultra-deep drilling fluid technology in the future is proposed:(1)The technology of high-temperature and high-salt resistant water-based drilling fluid should focus on improving high temperature stability,improving rheological properties,strengthening filtration control and improving compatibility with formation.(2)The technology of oil-based/synthetic drilling fluid resistant to high temperature should further study in the aspects of easily degradable environmental protection additives with low toxicity such as high temperature stabilizer,rheological regulator and related supporting technologies.(3)The drilling fluid technology for reservoir protection should be devoted to the development of new high-performance additives and materials,and further improve the real-time monitoring technology by introducing advanced sensor networks and artificial intelligence algorithms.(4)The lost circulation control of drilling fluid should pay more attention to the integration and application of intelligent technology,the research and application of high-performance plugging materials,the exploration of diversified plugging techniques and methods,and the improvement of environmental protection and production safety awareness.

Clinical efficacy and safety of kyphoplasty for the treatment of osteoporotic vertebral compression fractures at different surgical timings based on the theory of“dynamic-static integration”

Objective:To investigate the clinical efficacy and safety of percutaneous kyphoplasty at different surgical timings in the treatment of osteoporotic vertebral compression fracture(OVCF)based on the theory of“dynamic-static integration”.Methods:Patients with OVCF who underwent percutaneous kyphoplasty in our hospital were selected and divided into Groups A,B,and C for those undergoing surgery within 7,7—21,and>21 days of fracture occurrence.The variations in the amount of bone cement injected,pre-and post-operative pain levels,functional activity,deformity correction of the injured vertebrae,bone cement leakage,and vertebral body height loss were compared among the three groups.Results:Regarding pain relief and functional activity,the postoperative Visual Analog Scale and Oswestry Disability Index scores of the three groups significantly improved.Furthermore,the deformities of the injured vertebrae in the three groups were significantly corrected,with Groups A and B exhibiting superior correction compared to Group C.Moreover,the bone cement leakage rates in groups A and C were higher than that in Group B.At the 3-month follow-up,the loss of vertebral height in Group C was significantly higher than those in groups A and B.Conclusion:Kyphoplasty is effective for OVCF treatment.Early surgery can effectively restore the vertebral height of the injured vertebra,reduce kyphosis,and reduce height loss of the injured vertebra after surgery;nevertheless,treatment within 1—3 weeks of the fracture can reduce the occurrence of bone cement leakage,making the surgery safer.Therefore,surgical treatment within 1—3 weeks of fracture is safer and can achieve satisfactory therapeutic effects.From the perspective of traditional Chinese medicine,PKP surgery can transform the fracture end from a micromotion state to a fixed state,which fully embodies the theory of“dynamic-static integration”.

Microstructure and mechanical properties of Mg-Gd-Y-Zr alloy cast by metal mould and lost foam casting

The microstructure and mechanical properties of Mg-10.1Gd-3.74Y-0.25Zr （mass fraction, %） alloy （GW104 alloy） cast by metal mould casting （MMC） and lost foam casting （LFC） were evaluated, respectively. It is revealed that different forming modes do not influence the phase composition of as-cast alloy. In the as-cast specimens, the microstructures are similar and composed of α-Mg solid solution, eutectic compound of α-Mg＋Mg 24 （Gd, Y） 5 and cuboid-shaped Mg 5 （Gd, Y） phase; whereas the average grain size of the alloy produced by metal mould casting is smaller than that by lost foam casting. The eutectic compound of the alloy is completely dissolved after solution treatment at 525 ℃for 6 h, while the Mg 5 （Gd, Y） phase still exists after solution treatment. After peak-ageing, the lost foam cast alloy exhibits the maximum ultimate tensile strength of 285 MPa, and metal mould cast specimen 325 MPa at room temperature, while the tensile yield strengths of them are comparable. It can be concluded that GW104 alloy cast by lost foam casting possesses similar microstructure and evidently lower mechanical strength compared with metal mould cast alloy, due to slow solidification rate and proneness to form shrinkage porosities during lost foam casting process.

COCA语料库在教学中的应用——以lost in thoughts为例

文章通过在线COCA语料库探讨了lost in thoughts的应用。阐明在传统的字典中没列入的短语不表示不存在,在我们学习,教学,研究应该充分利用语料库打破传统的一些误区,更好地了解本族语者的使用语境。

High Cr white cast iron/carbon steel bimetal liner by lost foam casting with liquid-liquid composite process

Liners in wet ball mill for mineral processing industry must bear abrasive wear and corrosive wear, and consequently, the service life of the liner made from traditional materials, such as Hadfield steel and alloyed steels, is typically less than ten months. Bimetal liner, made from high Cr white cast iron and carbon steel, has been successfully developed by using liquid-liquid composite lost foam casting process. The microstructure and interface of the composite were analyzed using optical microscope, SEM, EDX and XRD. Micrographs indicate that the boundary of bimetal combination regions is staggered like dogtooth, two liquid metals are not mixed, and the interface presents excellent metallurgical bonding state. After heat treatment, the composite liner specimens have shown excellent properties, including hardness 〉 61 HRC, fracture toughness ak 〉16.5 J.cm2 and bending strength 〉1,600 MPa. Wear comparison was made between the bimetal composite liner and alloyed steel liner in an industrial hematite ball mill of WISCO, and the results of eight-month test in wet grinding environment have proved that the service life of the bimetal composite liner is three times as long as that of the alloyed steel liner.

Influence of mechanical vibration on the solidification of a lost foam cast 356 alloy

Mechanical vibration was applied to the solidification of a lost foam cast(LFC) 356 aluminum alloy.Effects of mechanical vibration,with different peak acceleration,on the size and morphology of α-Al phase,and also on the mechanical properties of the castings were studied.Results indicated that α-Al dendrites gradually grow into equiaxed grains as the peak acceleration of vibration is increased.When the peak acceleration is between about 1 to 4 g,α-Al phase distribution is uniform and is refined obviously.α-Al dendrites are reduced and the mechanical properties of the castings are improved significantly when compared to those of the castings that are produced without vibration.However,when the peak acceleration is higher than 4 g,strong vibration will lead to defects formation,such as sand adhesion,while the amount and size of pores will be increased.And due to the turbulent flow that caused by strong vibration,the chance of forming large pores in the matrix has been increased significantly.The increase in defects will result in the deterioration of mechanical properties.

Effect of Process Parameters on Porosity in Aluminum Lost Foam Process

Porosity is a main defect in aluminum alloy castings, which is also thought to be severe in aluminum alloy castings produced by lost foam process due to the pyrolysis of the polystyrene foam pattern during pouring. Fundamental experiments were carried out to evaluate the effect of process parameters such as the melt treatment, the cooling rate and the density of expanded polystyrene （EPS） foam on porosity in A356.2 bar casting. The effect of melt treatment including degassing and refining was investigated. The effect of cooling rate was also evaluated by changing the mold packing material such as the silica sand, the zircon sand and the steel shots. Gas entrapment due to the turbulent metal flow during mold filling in conventional molding process results in porosity. Mold filling sequence in lost foam process is different from that in conventional molding process. The effect of molten metal flow was estimated by comparing the density of the casting by conventional sodium silicate molding with that by lost foam process. Density measurement was conducted to analyze the extent of porosity in the casting. Source of the porosity in lost foam process can be divided into two factors, i.e. turbulence in molten metal flow and entraining residue or gas from the pattern during pouring.

Research progress and prospect of plugging technologies for fractured formation with severe lost circulation

By reviewing the mechanisms of drilling fluid lost circulation and its control in fractured formations, the applicability and working mechanisms of different kinds of lost circulation materials in plugging fractured formations have been summarized. Meanwhile, based on the types of lost circulation materials, the advantages, disadvantages, and application effects of corresponding plugging technologies have been analyzed to sort out the key problems existing in the current lost circulation control technologies. On this basis, the development direction of plugging technology for severe loss have been pointed out. It is suggested that that the lost circulation control technology should combine different disciplines such as geology, engineering and materials to realize integration, intelligence and systematization in the future. Five research aspects should be focused on:(1) the study on mechanisms of drilling fluid lost circulation and its control to provide basis for scientific selection of lost circulation material formulas, control methods and processes;(2) the research and development of self-adaptive lost circulation materials to improve the matching relationship between lost control materials and fracture scales;(3) the research and development of lost circulation materials with strong retention and strong filling in three-dimensional fracture space, to enhance the retention and filling capacities of materials in fractures and improve the lost circulation control effect;(4) the research and development of lost circulation materials with high temperature tolerance, to ensure the long-term plugging effect of deep high-temperature formations;(5) the study on digital and intelligent lost circulation control technology, to promote the development of lost circulation control technology to digital and intelligent direction.

Status quo and development trend of lost foam casting technology

Lost foam casting(LFC)technology has been widely applied to cast iron and cast steel.However,the development of LFC for Al and Mg alloys was relatively slower than that for cast iron and cast steel.The application of LFC to Al and Mg alloys needs more effort,especially in China.In this paper,the development history of LFC is reviewed,and the application situations of LFC to Al and Mg alloys are mainly discussed.Meanwhile,the key problems of LFC for Al and Mg alloys are also pointed out.Finally,the prospects for LFC technology are discussed,and some special new LFC technologies are introduced for casting Al and Mg alloys.In future,the development trends of green LFC technology mainly focus on the special new LFC methods,metal material,coating,heat treatment,new foam materials as well as purification technology of tail gas,etc.

Density and Mechanical Properties of Aluminum Lost Foam Casting by Pressurization during Solidification

Porosity is thought to be severe in aluminum alloy castings produced by lost foam process due to the pyrolysis of the polystyrene foam pattern during pouring, which results in detrimental effect in mechanical property. The slow solidification rate promotes the formation of gassing pin holes, and relative weakness of the thermal gradients can cause micro-shrinkage if the outline of the part complicates feeding in the lost foam casting. One of the methods to eliminate the porosity is to apply high pressure to the molten metal like an isostatic forging during solidification. Fundamental experiments were carried out to evaluate the effect of the external pressure on the porosity and mechanical properties of A356.2 alloy bar in the lost foam casting. Solidification time and porosity decreased with increasing the applied pressure during solidification. Applying external pressure was effective in decreasing the porosity and increasing the elongation of the lost foam casting.

Effect of vibration frequency on microstructure and performance of high chromium cast iron prepared by lost foam casting

In the present research, high chromium cast irons(HCCIs) were prepared using the lost foam casting(LFC) process. To improve the wear resistance of the high chromium cast irons(HCCIs), mechanical vibration was employed during the solidification of the HCCIs. The effects of vibration frequency on the microstructure and performance of the HCCIs under as-cast, as-quenched and as-tempered conditions were investigated. The results indicated that the microstructures of the LFC-produced HCCIs were refined due to the introduction of mechanical vibration, and the hardness was improved compared to that of the alloy without vibration. However, only a slight improvement in hardness was found in spite of the increase of vibration frequency. In contrast, the impact toughness of the as-tempered HCCIs increased with an increase in the vibration frequency. In addition, the wear resistance of the HCCIs was improved as a result of the introduction of vibration and increased with an increase in the vibration frequency.

Effect of pattern coating thickness on characteristics of lost foam Al-Si-Cu alloy casting

An experimental study on lost foam casting of an Al-Si-Cu alloy was conducted. The main objective was to study the effect of pattern coating thickness on casting imperfection and porosity percentage as well as eutectic silicon spacing of the alloy. The results showed that increasing slurry viscosity and flask dipping time influenced the casting integrity and microstructural characteristics. It was found that thinner pattern coating produced improved mould filling, refined microstructure and higher quality castings containing less porosity.

Effect of vibration frequency on primary phase and properties of grey cast iron fabricated by lost foam casting

The properties of gray cast iron(GCI)are affected by density of matrix,size of flake graphite and primary austenite.In this paper,the Y-type specimen of GCI was prepared by lost foam casting(LFC)with and without vibration,and the influence of vibration frequency on the density of matrix,size of primary phase,and properties of the GCI was studied.The results show that the length of the flake graphite and the size of the primary austenite in GCI firstly decrease and then increase with the increase of the vibration frequency.With a vibration frequency of 35 Hz,the length of the flake graphite is the shortest,the primary austenite is the finest and the density of the matrix is the highest.In addition,the tensile strength,elongation and hardness of the GCI firstly increase and then decrease with the increase of the vibration frequency,due to the refinement of the primary phase and the increase of the matrix density.In order to analyze the refinement mechanism of the primary phase of the GCI fabricated by the LFC with vibration,the solidification temperature fields of the GCI fabricated by the LFC with the vibration frequency of 0 and 35 Hz were measured.The results show that the vibration reduces the eutectic point of the GCI and increases the supercooling degree during the eutectic transformation.As a result,the length of the flake graphite and the size of the primary austenite in GCI fabricated by LFC with the vibration frequency of 35 Hz decrease.

Study on typical hole defects in AZ91D magnesium alloy prepared by low pressure lost foam casting

The hole defects can easily occur in magnesium alloy castings that are prepared by low pressure lost foam casting(LP-LFC)process when the process parameters such as vacuum,pouring temperature and f illing velocity are not properly selected.In this study,the forming mechanism of the hole defects in AZ91D magnesium castings by LP-LFC process was investigated.The shape,location and surface appearance of the hole defects were observed using optical microscopy and scanning electron microscopy,and the chemical composition on the surface of the holes was analyzed using energy spectrometer.The result indicates that there are two types of hole defects,i.e.,the pyrolysis products related hole defects,including concentrative hole and blow hole defects,and slag related hole defects.The concentrative hole and the blow-hole defects were formed either by the liquidEPS degradation products entrapped in the molten metal under the condition that the pouring temperature is equal to or lower than 730℃,or by the hindered transport of EPS pyrolysis products.Some irregular shape hole defects were caused by slag or by coating slough entrapment when the pouring temperature is equal to 750℃and the f illing velocity is equal to or greater than 100 mm·s-1.To reduce or eliminate the hole defects,the vacuum and f illing velocity must be properly chosen to ensure that the metal front prof ile exhibits convex shape and in laminar current state,and the pouring temperature should be just high enough to ensure that the molten melt has adequate heat energy to complete the foam pyrolysis and to fully occupy the mould.For AZ91D magnesium castings in this study,the parameters should be 730℃pouring temperature,0.02-0.03 MPa vacuum and 80mm·s-1f illing velocity.