Effect of low concentration electrolytes on the formation and corrosion resistance of PEO coatings on AM50 magnesium alloy

In this paper,the formation process,morphology,and electrochemical performance of PEO coatings on AM50 magnesium alloy prepared in low concentration phosphate,aluminate,and phosphate-aluminate electrolytes were systematically studied.The results show that the coatings prepared from the phosphate electrolytes have a higher thickness and better corrosion resistance properties compared to the other electrolytes.The coatings prepared from low concentration phosphate-aluminate mixed electrolytes have slightly thinner thickness,a similar coating structure and an order of magnitude lower value of electrochemical impedance compared with phosphate electrolyte coatings.The Coatings prepared from low concentration aluminate electrolytes have the lowest thickness and the worst corrosion resistance properties which gets close to corrosion behavior of the bare AM50 under the same test conditions.Considering application,coatings prepared from single low concentration phosphate electrolytes and low concentration phosphate-aluminate electrolytes have greater potential than single low concentration aluminate coatings.However,reducing the electrolyte concentrations of coating forming ions too much has negative influence on the coating growth rate.

Diluted low concentration electrolyte for interphase stabilization of high-voltage LiNi_(0.5)Mn_(1.5)O_(4) cathode

The Co-free Li Ni_(0.5)Mn_(1.5)O_(4)(LNMO)is a promising cathode for lithium-ion batteries owing to its high operating voltage and low costs.However,the synthesis of LNMO is generally time and energy consuming,and its practical application is hindered by the lack of a compatible electrolyte.Herein,a spray pyrolysis-based energy-saving synthesis method as well as a diluted low concentration electrolyte(0.5 M LiPF_(6) in a mixture of fluoroethylene carbonate/dimethyl carbonate/1,1,2,2-tetrafluoroethyl-2,2,3,3-tetrafluoropropyl ether(FEC:DMC:TTE,1:4:5 by volume))are proposed to address these challenges.Owing to the unique features of the precursor prepared by spray pyrolysis,well-crystallized LNMO single-crystal can be obtained within 1 h calcination at 900℃.Besides,the fluorinated interphases derived from the diluted low concentration electrolyte not only mitigate the Mn dissolution and Al corrosion at the cathode side,but also suppresses dendritic Li deposition at the anode side,thus enabling stable cycling of both LNMO and Li metal anode.Thus,30μm Li|LNMO(1.75 m A h cm^(-2))cells achieve a high capacity retention(90.9%)after 168 cycles in the diluted low concentration electrolyte.

Effects of endogenous dopamine induced by low concentration atropine eye drops on choroidal neovascularization in high myopia mice

AIM:To evaluate effects of endogenous dopamine induced by low concentration atropine eye drops on choroidal neovascularization(CNV)in high myopia mice.METHODS:The C57BL/6J mice were deprived of the right eye for 4wk,and the high myopia was diagnosed by optometry,the diopter was less than-6.00 D,and CNV was induced by 532 nm laser.The changes of dopamine D1 receptor(DRD1),dopamine D2 receptor(DRD2),and vascular endothelial growth factor A(VEGFA)were detected by Western blot technology at 0.5,1,2h,and 7d after 0.01%,0.05%,and 0.1%atropine eye drops,respectively,the area of CNV was measured.RESULTS:Significant increases were observed on the expression of DRD2 in mouse high myopia model at 0.5,1,2h,7d with 0.05%and 0.1%atropine eye drops(P<0.05).Significant decreases were observed on the expression of DRD1 and VEGFA in mouse high myopia model at 0.5,1,2h,7d with 0.05%and 0.1%atropine eye drops(P<0.05).The area of CNV induced by laser in the drug-treated group was significantly smaller than that in the control group,and the higher the concentration,the more significant the inhibitory effect(P<0.05).CONCLUSION:The 0.01%,0.05%,0.1%atropine eye drops can decrease the level of VEGFA and inhibit high myopia CNV indirectly by up-regulating the level of DRD2 and down-regulating the level of DRD1,and the effect of 0.05%and 0.1%atropine eye drops is more significant.

Low Complexity Detection Algorithms Based on ADMIN for Massive MIMO

This paper proposes the alternating direction method of multipliers-based infinity-norm(ADMIN) with threshold(ADMIN-T) and with percentage(ADMIN-P) detection algorithms,which make full use of the distribution of the signal to interference plus noise ratio(SINR) for an uplink massive MIMO system.The ADMIN-T and ADMIN-P detection algorithms are improved visions of the ADMIN detection algorithm,in which an appropriate SINR threshold in the ADMIN-T detection algorithm and a certain percentage in the ADMIN-P detection algorithm are designed to reduce the overall computational complexity.The detected symbols are divided into two parts by the SINR threshold which is based on the cumulative probability density function(CDF) of SINR and a percentage,respectively.The symbols in higher SINR part are detected by MMSE.The interference of these symbols is then cancelled by successive interference cancellation(SIC).Afterwards the remaining symbols with low SINR are iteratively detected by ADMIN.The simulation results show that the ADMIIN-T and the ADMIN-P detection algorithms provide a significant performance gain compared with some recently proposed detection algorithms.In addition,the computational complexity of ADMIN-T and ADMIN-P are significantly reduced.Furthermore,in the case of same number of transceiver antennas,the proposed algorithms have a higher performance compared with the case of asymmetric transceiver antennas.

A Hybrid Five-Level Single-Phase Rectifier with Low Common-Mode Voltage

Rectifiers with high efficiency and high power density are crucial to the stable and efficient power supply of 5G communication base stations,which deserves in-depth investigation.In general,there are two key problems to be addressed:supporting both alternating current(AC)and direct current(DC)input,and minimizing the common-mode voltage as well as leakage current for safety reasons.In this paper,a hybrid five-level single-phase rectifier is proposed.A five-level topology is adopted in the upper arm,and a half-bridge diode topology is adopted in the lower arm.A dual closed-loop control strategy and a flying capacitor voltage regulation method are designed accordingly so that the compatibility of both AC and DC input is realized with low common voltage and small passive devices.Simulation and experimental results demonstrate the effectiveness and performance of the proposed rectifier.

Soft transmission of 3D video for low power and low complexity scenario

Thanks to the rapid development of naked-eye 3D and wireless communication technology,3D video related applications on mobile devices have attracted a lot of attention.Nevertheless,the time-varying characteristics of the wireless channel is very challenging for conventional source-channel coding based transmission strategy.Also,the high complexity of source-channel coding based transmission scheme is undesired for low power mobile terminals.An advanced transmission scheme named Softcast was proposed to achieve efficient transmission performance for 2D image/video.Unfortunately,it cannot be directly applied to wireless 3D video transmission with high efficiency.This paper proposes a more efficient soft transmission scheme for 3D video with a graceful quality adaptation within a wide range of channel Signal-to-Noise Ratio(SNR).The proposed method first extends the linear transform to 4 dimensions with additional view dimension to eliminate the view redundancy,and then metadata optimization and chunk interleaving are designed to further improve the transmission performance.Meanwhile,a synthesis distortion based chunk discard strategy is developed to improve the overall 3D video quality under the condition of limited bandwidth.The experimental results demonstrate that the proposed method significantly improves the 3D video transmission performance over the wireless channel for low power and low complexity scenarios.

Rheological properties of low consistency TMP from thinning wood of Chinese Fir

The rheological behavior of low consistency thermomechanical pulp of Chinese fir harvested by intermediate thinning was analyzed. The results show that the apparent viscosity of pulp changed along with the beating degree, pulp consistency and shearing velocity. With the increasing of pulp consistency, the apparent viscosity of pulp increased gradually. Beating degree of pulp had an effect on microstructure of pulp. The apparent viscosity of pulp declined as beating degree of pulp increased, and the apparent viscosity of pulp fell along with the shearing velocity increasing. Based on the results, the rheological models are set up. The models showed that the fluid types of the low consistency pulp could be described as pseudoplastics fluids （non-Newtonian fluids）.

Low complexity method for spreading sequence estimation of DSSS signal in non-cooperative communication systems

It is a necessary step to estimate the spreading sequence of direct sequence spread spectrum （DSSS） signal for blind despreading and demodulation in non-cooperative communications. Two innovative and effective detection statistics are proposed to implement the synchronization and spreading sequence estimation procedure. The proposed algorithm also has a low computational complexity with only linear additions and modifications. Theoretical analysis and simulation results show that the algorithm performs quite well in low SNR environment, and is much better than all the existing typical algorithms with a comprehensive consideration both in performance and computational complexity.

Correction of low corneal astigmatism in cataract surgery

· AIM: To evaluate and compare aspheric toric intraocular lens(IOL) implantation and aspheric monofocal IOL implantation with limbal relaxing incisions(LRI) to manage low corneal astigmatism(1.0-2.0 D) in cataract surgery.· METHODS: A prospective randomized comparative clinical study was performed. There were randomly recruited 102 eyes(102 patients) with cataracts associated with corneal astigmatism and divided into two groups. The first group received toric IOL implantation and the second one monofocal IOL implantation with peripheral corneal relaxing incisions. Outcomes considered were: visual acuity, postoperative residual astigmatism, endothelial cell count, the need for spectacles, and patient satisfaction. To determine the postoperative toric axis, all patients who underwent the toric IOL implantation were further evaluated using an OPD Scan III(Nidek Co, Japan). Follow-up lasted 6mo.· RESULTS: The mean uncorrected distance visual acuity(UCVA) and the best corrected visual acuity(BCVA) demonstrated statistically significant improvement after surgery in both groups. At the end of the follow-up the UCVA was statistically better in the patients with toric IOL implants compared to those patients who underwent implantation of monofocal IOL plus LRI. The mean residual refractive astigmatism was of 0.4 D for the toric IOL group and 1.1 D for the LRI group(P 【0.01). No difference was observed in the postoperative endothelial cell count between the two groups.· CONCLUSION: The two surgical procedures demonstrated a significant decrease in refractive astigmatism. Toric IOL implantation was more effective and predictable compared to the limbal relaxing incision.

Timing Advanced Estimation Algorithm of Low Complexity Based on DFT Spectrum Analysis for Satellite System

In satellite mobile communication system, relative movement of the satellite and the terminal will cause a large Doppler offset. Timing advanced estimation with Zadoff-Chu sequence is sensitive to the frequency offset. When the frequency offset is larger than one times subcarrier spacing, the value of peak cannot be detected at the receiving end. To suppress the larger Doppler frequency shift, this paper proposes a novel timing advanced estimation scheme(TAE-MCD) for satellite communication system. In this algorithm, t r a n s m i t t e d s i g n a l i s d i v i d e d i n t o Z C sequence and its conjugate sequence. Using multiplication and DFT operation to find the estimated peak at the receiving end, and make subtraction with the obtained sequences at last. The scheme can not only inhibit the adverse effects of large Doppler frequency shift in timing estimation effectively, but also reduce the computational complexity at the receiving end and improve the work efficiency of the hardware. Simulations results show that TAEMCD outperform the existing timing advanced estimation methods, on the condition of no additional time and frequency resource are needed.

High loading FeS2 nanoparticles anchored on biomass-derived carbon tube as low cost and long cycle anode for sodium-ion batteries

In recent years, the sodium storage mechanism and performance optimization of FeS2 have been studied intensively. However, before the commercial application of FeS2, preconditions of low-cost, simple craft and scale production of nanoscale FeS2 are also essential. Based on above challenges, mesh-like FeS2/carbon tube/FeS2 composites are prepared simply from green, low-cost and renewable natural herb in this work. With the assistance of protogenetic interconnected carbon tube network(only 5.3 wt%), FeS2/carbon tube/FeS2 composites show high capacity(542.2 mA h g^-1), good stability(< 0.005% per cycle over 1000 cycles), and excellent rate performance(426.2 mA h g^-1 at 2 A g^-1).The outstanding electrochemical performance of FeS2/carbon tube/FeS2 composites may be attributed to the unique interconnected reticular structure, meaning that FeS2 nanoparticles are effectively immobilized by carbon tube network via physical encapsulation and chemical bonding.More importantly, this work may provide green and low cost preparation method for specially structured metal sulfides/carbon composites,which promotes their commercial utilization in environmentally friendly energy storage system.

Recent progress of green sorbents-based technologies for low concentration CO_(2) capture

The increased concentration of CO_(2) due to continuous breathing and no discharge of human beings in the manned closed space,like spacecraft and submarines,can be a threat to health and safety.Effective removal of low concentration CO_(2) from the manned closed space is essential to meet the requirements of long-term space or deep-sea exploration,which is an international frontier and trend.Ionic liquids(ILs),as a widespread and green solvent,already showed its excellent performance on CO_(2) capture and absorption,indicating its potential application in low concentration CO_(2) capture.In this review,we first summarized the current methods and strategies for direct capture from low concentration CO_(2) in both the atmosphere and manned closed spaces.Then,the multi-scale simulation methods of CO_(2) capture by ionic liquids are described in detail,including screening ionic liquids by COSMO-RS methods,capture mechanism by density functional theory and molecular dynamics simulation,and absorption process by computational fluid dynamics simulation.Lastly,some typical IL-based green technologies for low concentration CO_(2) capture,such as functionalized ILs,co-solvent systems with ILs,and supported materials based on ILs,are introduced,and analyzed the subtle possibility in manned closed spaces.Finally,we look forward to the technology and development of low concentration CO_(2) capture,which can meet the needs of human survival in closed space and proposed that supported materials with ionic liquids have great advantages and infinite possibilities in the vital area.

Effects of Low Concentrations of Di-(2-ethylhexyl) and Mono-(2-ethylhexyl) Phthalate on Steroidogenesis Pathways and Apoptosis in the Murine Leydig Tumor Cell Line MLTC-1

The aim of this study was to evaluate the effects of low concentrations of DEHP and MEHP on steroidogenesis in a murine Leydig tumor cell line （MLTC-1） in vitro. The result of flow cytometry analysis revealed that the proportion of apoptotic cells was significantly increased after the exposure to DEHP. All three genes （P450scc, P450c17, and 38HSD） under study showed an increased expression following exposure to DEHP or MEHP, although some insignificant inhibitory effects appeared in the 10μmol/L treatment group as compared with the controls. It was also found that DEHP or MEHP stimulated INSL3 mRNA and protein especially in the 0.001 μmol/L treatment group. Testosterone secretions were stimulated after the exposure to DEHP or MEHP. Alterations of steroidogenic enzymes and INSL3 in MLTC-1 cells might be involved in the biphasic effects of DEHP/MEHP on androgen production.

Thermal Stability of Low Cost Nd-Fe-B Magnets

1.IntroductionSince the Nd-Fe-B magnets appearedin 1983,researchers,producers and users ofthe permanent magnetic materials have paidgreat attention to them.Because the mag-nets have low Curie temperature Tc andbad thermal stability as well as easeoxidation,their applications are limited insome fields.The researchers are greatly in-terested in increase energy product

Insight into MgO promoter with low concentration for the carbon-deposition resistance of Ni-based catalysts in the CO_2 reforming of CH_4

The CO2reforming of CH4is studied over MgO‐promoted Ni catalysts,which were supported on alumina prepared from hydrotalcite.This presents an improved stability compared with non‐promoted catalysts.The introduction of the MgO promoter was achieved through the‘‘memory effect’’of the Ni‐Al hydrotalcite structure,and ICP‐MS confirmed that only0.42wt.%of Mg2+ions were added into the Ni‐Mg/Al catalyst.Although no differences in the Ni particle size and basicity strength were observed,the Ni‐Mg/Al catalyst showed a higher catalytic stability than the Ni/Al catalyst.A series of surface reaction experiments were used and showed that the addition of a MgO promoter with low concentration can promote CO2dissociation to form active surface oxygen arising from the formation of the Ni‐MgO interface sites.Therefore,the carbon‐resistance promotion by nature was suggested to contribute to an oxidative environment around Ni particles,which would increase the conversion of carbon residues from CH4cracking to yield CO on the Ni metal surface.?2018,Dalian Institute of Chemical Physics,Chinese Academy of Sciences.Published by Elsevier B.V.All rights reserved.

Design and Implementation of a Novel HomePlug-Based Solution for Low Cost and High Performance Smart Home Networking

As the smart home is the end-point power consumer, it is the major part to be controlled in a smart micro grid. There are so many challenges for implementing a smart home system in which the most important ones are the cost and simplicity of the implementation method. It is clear that the major share of the total cost is referred to the internal controlling system network; although there are too many methods proposed but still there is not any satisfying method at the consumers＇ point of view. In this paper, a novel solution for this demand is proposed, which not only minimizes the implementation cost, but also provides a high level of reliability and simplicity of operation; feasibility, extendibility, and flexibility are other leading properties of the design.

Low complexity DOA estimation for massive UCA with single snapshot

In this paper, a low complexity direction of arrival(DOA) estimation method for massive uniform circular array(UCA) with single snapshot is proposed.Firstly, the coarse DOAs are estimated by finding the peaks from the circular convolution between a fixed coefficient vector and the received data vector.Thereafter, in order to refine coarse DOA estimates, we reconstruct the direction matrix based on the coarse DOA estimations and take the first order Taylor expansion with DOA estimation offsets into account.Finally, the refined estimations are obtained by compensating the offsets, which are obtained via least squares(LS) without any complex searches.In addition, the refinement can be iteratively implemented to enhance the estimation results.Compared to the offset search method, the proposed method achieves a better estimation performance while requiring lower complexity.Numerical simulations are presented to demonstrate the effectiveness of the proposed method.

Low cost, high performance supercapacitor electrode using coconut wastes: eco-friendly approach

Low cost, high performance supercapacitor electrodes were fabricated using coconut waste as precursor. Simple one step pyrolysis is adopted to get the spherical shaped particle where lignocellulosic nature of carbon converts into porous carbon nanospheres. Three types of coconut wastes, namely, coconut fiber(CF), coconut leaves(CL) and coconut stick(CS) have been studied and compared for their application in supercapacitors. Uniform spherical shape with particle size ranging from 30 to 60 nm for leaves and sticks and20 nm for fibers was obtained. The electrochemical properties of the porous carbon nanospheres were studied using cyclic voltammetry(CV), chronopotentiometry(CP) and electrochemical impedance spectroscopy(EIS). The porous carbon nanospheres derived from all the three biowaste samples show good electrochemical performance for supercapacitor application. Porous carbon nanospheres derived from coconut fiber exhibited maximum specific capacitance of 236 F/g followed by coconut stick and coconut leaves with 208 and 116 F/g respectively at a scan rate of 2 m V/s. Further impedance studies showed a charge transfer resistance of 4.9 for the porous carbon nanospheres derived from coconut fiber, while those from coconut leaves and coconut stick exhibited a slightly higher resistance of 6 and14.2, respectively. The simple eco-friendly approach we have demonstrated for synthesizing coconut waste based carbon nanospheres makes them excellent candidates for future, low-cost, energy storage devices.

Effect of Low Content Chlorophyll on Distribution Properties of Absorbed Light Energy in Leaves of Mutant Rice

This paper reported the diurnal variations of photochemical efficiency of PSII, thermaldissipation rate and other physiology process in the low content chlorophyll mutant rice andits wild type under field conditions, and analyzed the difference of absorbed light distributionbetween the two rice varieties in a day. The results showed that the mutant had poor absorbedlight because of its little light absorption coefficient, but higher electron transportg ratecould partly reduce the disadvantageous effect of deficient absorbed light in mutant. Comparedwith wild-type rice, the mutant had less excess excitation energy and the fraction of absorbedlight allocated to photochemical process was more.

Numerical Simulation of Stall Flow Control Using a DBD Plasma Actuator in Pulse Mode

A numerical simulation method is employed to investigate the effects of the unsteady plasma body force over the stalled NACA 0015 airfoil at low Reynolds number flow conditions. The plasma body force created by a dielectric barrier discharge actuator is modeled with a phenomenological method for plasma simulation coupled with the compressible Navier-Stokes equations. The governing equations are solved using an efficient implicit finitevolume method. The responses of the separated flow field to the effects of an unsteady body force in various inter- pulses and duty cycles as well as different locations and magnitudes are studied. It is shown that the duty cycle and inter-pulse are key parameters for flow separation control. Additionally, it is concluded that the body force is able to attach the flow and can affect boundary layer grow that Mach number 0.1 and Reynolds number of 45000.