Effect of low concentration electrolytes on the formation and corrosion resistance of PEO coatings on AM50 magnesium alloy

In this paper,the formation process,morphology,and electrochemical performance of PEO coatings on AM50 magnesium alloy prepared in low concentration phosphate,aluminate,and phosphate-aluminate electrolytes were systematically studied.The results show that the coatings prepared from the phosphate electrolytes have a higher thickness and better corrosion resistance properties compared to the other electrolytes.The coatings prepared from low concentration phosphate-aluminate mixed electrolytes have slightly thinner thickness,a similar coating structure and an order of magnitude lower value of electrochemical impedance compared with phosphate electrolyte coatings.The Coatings prepared from low concentration aluminate electrolytes have the lowest thickness and the worst corrosion resistance properties which gets close to corrosion behavior of the bare AM50 under the same test conditions.Considering application,coatings prepared from single low concentration phosphate electrolytes and low concentration phosphate-aluminate electrolytes have greater potential than single low concentration aluminate coatings.However,reducing the electrolyte concentrations of coating forming ions too much has negative influence on the coating growth rate.

Evaluation of Cold Resistance and Semi-lethal Low Temperature(LT_(50))of Nine Pear Cultivars

[Objectives]To evaluate the cold resistance and semi-lethal temperature of pear cultivars,and provide a theoretical basis for the regional extension and breeding of cold-resistant pear cultivars.[Methods]Nine pear cultivars were used to study the changes in relative conductivity and cell injury rate of pear branches under low temperature stress,and the semi-lethal temperature(LT_(50))of pear branches was analyzed by fitting Logistic equation.[Results]The relative conductivity and cell injury rate of pear branches took on the trend of slow increase,rapid increase,and slow increase the decrease of treatment temperature.The LC_(50) of the nine pear cultivars were as follows:Nanguo pear-33.9℃,Wanyu-32.3℃,Red D Anjou-31.8℃,Jinfeng-31.3℃,Wujiuxiang-29.2℃,20 th Century Pear-29.1℃,Hanxiang-35.1℃,Yuluxiang-27.9℃ and Korla Fragrant Pear-29.2℃.[Conclusions]The semi-lethal temperature could reflect the cold resistance of pear trees,and Wanxiang had better cold resistance.The evaluation of cold resistance and semi-lethal temperature of pear cultivars can provide theoretical basis for regional extension and breeding of cold-resistant pear cultivars.

Effect of samarium doping on the activity and sulfur resistance of Ce/MnFeO_(x) catalyst for low-temperature selective catalytic reduction of NO_(x) by ammonia

The self-made MnFeO_(x) catalysts doped with cerium and samarium were prepared by impregnation method for low-temperature selective catalytic reduction(SCR)by NH3.In this work,the surface properties of the series of MnFe-based catalysts were studied.The results indicate Sm-modified catalyst have superior low-temperature SCR activity;NO_(x) conversion maintained at nearby to 100%at 90℃ to 240℃.In addition,The N_(2) selectivity of Sm doping remains above 80%in the range of 60℃ to 150℃.In SO_(2) poisoning test,the NO_(x) conversion can be remained>90%after 10 h of reaction.The XPS,NH_(3)-TPD and H_(2)-TPR results show the catalyst with Sm doping enhances the acid sites and oxidation catalytic sites of mixed oxides serves for improving oxygen vacancies and transfer electrons.In situ diffuse reflaxions infrared Fourier transformations spectroscopy(DRIFTS)results show that NO_(x) is more easily adsorbed on the surface after Sm doping,which provided favorable conditions for the NH_(3)-SCR reaction to proceed.The reaction at the catalyst surface will follow the L-H reaction mechanism by transient reaction test.

A"Concentrated lonogel-in-Ceramic"Silanization Composite Electrolyte with Superior Bulk Conductivity and Low Interfacial Resistance for Quasi-Solid-State Li Metal Batteries

The ideal composite electrolyte for the pursued safe and high-energy-density lithium metal batteries(LMBs)is expected to demonstrate peculiarity of superior bulk conductivity,low interfacial resistances,and good compatibility against both Li-metal anode and high-voltage cathode.There is no composite electrolyte to synchronously meet all these requirements yet,and the battery performance is inhibited by the absence of effective electrolyte design.Here we report a unique"concentrated ionogel-in-ceramic"silanization composite electrolyte(SCE)and validate an electrolyte design strategy based on the coupling of high-content silane-conditioning garnet and concentrated ionogel that builds well-percolated Li+transport pathways and tackles the interface issues to respond all the aforementioned requirements.It is revealed that the silane conditioning enables the uniform dispersion of garnet nanoparticles at high content(70 wt%)and forms mixed-lithiophobic-conductive LiF-Li3N solid electrolyte interphase.Notably,the yielding SCE delivers an ultrahigh ionic conductivity of 1.76 X 10^(-3)S cm^(-1)at 25℃,an extremely low Li-metal/electrolyte interfacial area-specific resistance of 13Ωcm^(2),and a distinctly excellent long-term 1200 cycling without any capacity decay in 4.3 V Li‖LiNi_(0.5)Co_(0.2)Mn_(0.3)O_(2)(NCM523)quasi-solid-state LMB.This composite electrolyte design strategy can be extended to other quasi-/solid-state LMBs.

Low-Level Antibiotic Resistance among Staphylococcus aureus and Gram-Negative Pathogens from Infected Skin and Soft Tissues in Rural Kenya

Introduction: Bacterial skin and soft tissue infections (SSTIs) are a cause of frequent inpatient and outpatient care visits whose causative agents are associated with a high antimicrobial resistance burden. For insights on antimicrobial susceptibilities in a rural setting, we examined specimens from suspected SSTIs from two public health facilities in Kenya. We additionally assessed antibiotic use, appropriateness of empiric therapy and risk factors for SSTI. Methodology: Between 2021 and 2023, 265 patients at Kisii and Nyamira County Referral hospitals were enrolled. Wound swabs/aspirates were collected and processed following standard microbiological procedures. Identification and antimicrobial susceptibility were performed using the VITEK 2 Compact platform. Demographic, clinical, and microbiological data were analyzed with R Statistical software. Results: S. aureus was isolated in 16.2% (43/265) of patients with a methicillin resistance (MRSA) proportion of 14% (6/43). While 13/15 drugs elicited susceptibilities ranging from 84% - 100%, penicillin (16%) and trimethoprim-sulfamethoxazole [TMP-SXT] (23%) yielded the lowest susceptibilities. Escherichia coli (n = 33), Klebsiella pneumoniae (n = 8), Pseudomonas aeruginosa (n = 8), and Citrobacter species (n = 4) were the most commonly isolated gram-negative species. Gram-negative strains showed high susceptibilities to most of the tested drugs (71% - 100%) with the exception of ampicillin (18%), TMP-SXT (33%), and first and second generation cephalosporins. Conclusions: The low MRSA prevalence and generally high antibiotic susceptibilities for S. aureus and gram-negative bacteria present opportunities for antibiotic stewardship in the study setting. Diminished susceptibilities against penicillin/ampicillin and TMP-SXT accord with prevailing local data and add a layer of evidence for their cautious empiric use.

Multiscale Study on Low Temperature Crack Resistance Mechanism of Steel Slag Asphalt Mixture

The objective of this paper was to study low temperature crack resistance mechanism of steel slag asphalt mixture(SAM).Thermal stress restrained specimen test(TSRST)and three-point bending test were carried out to evaluate the low-temperature crack resistance of SAM and basalt asphalt mixture(BAM).Based on the digital image correlation technique(DIC),the strain field distribution and crack propagation of SAM were analyzed from the microscopic point of view,and a new index,crack length factor(C),was proposed to evaluate the crack resistance of the asphalt mixture.The crystal phase composition and microstructure of steel slag aggregate(SA)and basalt aggregate(BA)were studied by X-ray diffraction(XRD)and scanning electron microscopy(SEM)to explore the low-temperature crack resistance mechanism of SAM.Results show that the low-temperature crack resistance of SAM is better than that of BAM;SAM has good integrity and persistent elastic deformation,and its bending failure mode is a hysteretic quasi-brittle failure;The SA surface is evenly distributed with pores and has surface roughness.SA has the composition phase of alkaline aggregate-calcite(CaCO3),so it has good adhesion to asphalt,which reveals the mechanism of excellent low-temperature crack resistance of SAM.

Cellular models of stress resistance may pave ways to fight neurodegenerative diseases

Alzheimer's disease(AD),the most common form of neurodegeneration,is characterized by selective neuronal vulnerability and brain regionselective neuron demise.The entorhinal cortex and hippoc,ampal CA1 projection neurons are at greater risk in AD whereas other regions display resistance to neurodegeneration.Interestingly,the cerebellum,a phylogenetically very old region,is affected only very late in the disease progression.

Investigation of bubbles escape behavior from low basicity mold flux for high-Mn high-Al steels using 3D X-ray microscope

During the continuous casting process of high-Mn high-Al steels,various types of gases such as Ar need to escape through the top of the mold.In which,the behavior of bubbles traversing the liquid slag serves as a restrictive link,closely associated with viscosity and the thickness of liquid slag.In contrast to two-dimensional surface observation,three-dimensional(3D)analysis method can offer a more intuitive,accurate,and comprehensive information.Therefore,this study employs a 3D X-ray microscope(3D-XRM)to obtained spatial distribution and 3D morphological characteristics of residual bubbles in mold flux under different basicity of liquid slag,different temperatures,and different holding times.The results indicate that as basicity of slag increases from 0.52 to 1.03,temperature increases from 1423 to 1573 K,the viscosity of slag decreases,the floating rate of bubbles increases.In addition,when holding time increases from 10 to 30 s,the bubbles floating distance increases,and the volume fraction and average equivalent sphere diameter of the bubbles solidified in the mold flux gradually decreases.In one word,increasing the basicity,temperature,and holding time leading to an increase in the removal rate of bubbles especially for the large.These findings of bubbles escape behavior provide valuable insights into optimizing low basicity mold flux for high-Mn high-Al steels.

Understanding the link between type 2 diabetes mellitus and Parkinson's disease:role of brain insulin resistance

Type 2 diabetes mellitus and Parkinson's disease are chronic diseases linked to a growing pandemic that affects older adults and causes significant socio-economic burden.Epidemiological data supporting a close relationship between these two aging-related diseases have resulted in the investigation of shared pathophysiological molecular mechanisms.Impaired insulin signaling in the brain has gained increasing attention during the last decade and has been suggested to contribute to the development of Parkinson's disease through the dysregulation of several pathological processes.The contribution of type 2 diabetes mellitus and insulin resistance in neurodegeneration in Parkinson's disease,with emphasis on brain insulin resistance,is extensively discussed in this article and new therapeutic strategies targeting this pathological link are presented and reviewed.

Preparation of Low Ratio Magnesium Ccement by Acid Leaching Treatment of Boron Mud

The effects of liquid-solid ratio and reaction time on the leaching rate of magnesium at room temperature were investigated,as well as the effects of the molar ratio of MgO/MgCl_(2),the amount of water added,and the amount of acid-impregnated slag dosed on the compressive strength and water resistance of LR-MOC.The results showed that the magnesium element in the boron mud could be maximally leached under the conditions of 1:1 concentration of hydrochloric acid at room temperature,liquid-solid ratio of 2.5 mL·g^(-1),and reaction time of 5 h,and the main products were amorphous SiO_(2) as well as a small amount of magnesium olivine which had not been completely reacted.The LR-MOC prepared using the acid-soaked mixture could reach a softening coefficient of 0.85 for 28 d of water immersion when the molar ratio of MgO/MgCl_(2) was 2.2,the amount of water added was 0 g,and the acid-soaked slag dosing was 40 wt%,which also led to an appreciable late-strength,with an increase of 19.4%in compressive strength at 28 d compared to that at 7 d.Unlike previous studies,LR-MOC prepared in this way has a final strength phase that is not the more easily hydrolysed 3-phase but the lath-like 5-phase.For this phenomenon,we analyzed the mechanism and found that,during the acid leaching process,a part of amorphous SiO_(2) dissolved in the acid leaching solution formed a silica sol,in which Mg^(2+)played a bridging role to make the silica sol more stable.With the addition and hydrolysis of MgO,the silica sol gel coagulation slows down,providing a capping layer to inhibit the hydrolysis of the 5-phase crystals and providing some strength after coagulation.The amorphous SiO_(2) in the other part of the acid-impregnated slag generated M-S-H gel with Mg^(2+)and OH-,which synergised with the dense structure composed of interlocking crystals to improve the water resistance of LR-MOC.

Transient extreme insulin resistance in a critically ill patient:A case report

BACKGROUND Acute hyperglycemia due to insulin resistance is common in critically ill patients,typically managed with insulin infusion.However,the occurrence of transient extreme insulin resistance(EIR)requiring exceptional high-dose insulin is rare.CASE SUMMARY We present the case of a 68-year-old woman with pneumonia who suffered an out-of-hospital cardiac arrest,subsequently developing transient EIR following a new episode of sepsis.Remarkably,insulin resistance rapidly reversed when the insulin infusion rate peaked at 960 units/hour(a total of 18224 units on that day),and it was promptly titrated down to zero upon achieving the target glucose level.CONCLUSION Exceptional high-dose insulin infusion may be required in critically ill patients with stress-related EIR,which is typically transient.Clinicians should be aware of the phenomenon and cautious to avoid hypoglycemia and fluid overload during the steep titration of high-dose insulin infusion.

Microstructure and Wear/corrosion Resistance of Stainless Steel Laser-alloyed with Mn+W_(2)C, Mn+NiWC and Mn+SiC

In-situ formed high Mn steel coating reinforced by carbides was formed by laser surface alloying(LSA).Laser alloyed layers on 1Cr18Ni9Ti steel with Mn+W_(2)C(specimen A),Mn+NiWC(specimen B)and Mn+SiC(specimen C)powders were fabricated to improve the wear and corrosion behavior of 1Cr18Ni9Ti steel blades in high speed mixers.Microstructure evolution,phases,element distribution,microhardness,wear and corrosion behavior of the laser alloyed layers were investigated.Results indicated that high Mn steel matrix composites with undissolved W_(2)C,WC and other in-situ formed carbides were formed by LSA with Mn+W_(2)C and Mn+NiWC while SiC totally dissolved into the high Mn matrix when adding Mn+SiC.Ni as the binding phase in Ni-WC powder decreased the crack sensitivity of the alloyed layer as compared with the addition of W_(2)C powder.An improvement in average microhardness was achieved in the matrix in specimen A,B and C,with the value of 615,602 and 277 HV_(0.5),while that of the substrate was 212 HV_(0.5).The increase of microhardness,wear and corrosion resistance is highly corelated to microstructure,formed phases,type and content of carbides,micro-hardness and toughness of the alloyed layers.

Combined BRAF G469A mutation and echinoderm microtubule associated protein like-4-anaplastic lymphoma kinase rearrangement with resistance:A case report and review of literature

BACKGROUND Through deeper understanding of targetable driver mutations in non-small-cell lung cancer(NSCLC)over the past years,some patients with driver mutations have benefited from the targeted molecular therapies.Although the anaplastic lymphoma kinase and BRAF mutations are not frequent subtypes in NSCLC,the availability of several targeted-drugs has been confirmed through a series of clinical trials.But little is clear about the proper strategy in rare BRAF G469A mutation,not to mention co-exhibition of anaplastic lymphoma kinase and BRAF G469A mutations,which is extremely rare in NSCLC.CASE SUMMARY We present a patient to stage IVA lung adenocarcinoma with coexisting echinoderm microtubule associated protein like-4 rearrangement and BRAF G469A mutation.She received several targeted drugs with unintended resistance and suffered from unbearable adverse events.CONCLUSION Due to the rarity of co-mutations,the case not only enriches the limited literature on NSCLC harbouring BRAF G469A and echinoderm microtubule associated protein like-4 mutations,but also suggests the efficacy and safety of specific multiple-drug therapy in such patients.

Flow and heat transfer characteristics of regenerative cooling parallel channel

Due to the complex high-temperature characteristics of hydrocarbon fuel,the research on the long-term working process of parallel channel structure under variable working conditions,especially under high heat-mass ratio,has not been systematically carried out.In this paper,the heat transfer and flow characteristics of related high temperature fuels are studied by using typical engine parallel channel structure.Through numeri⁃cal simulation and systematic experimental verification,the flow and heat transfer characteristics of parallel chan⁃nels under typical working conditions are obtained,and the effectiveness of high-precision calculation method is preliminarily established.It is known that the stable time required for hot start of regenerative cooling engine is about 50 s,and the flow resistance of parallel channel structure first increases and then decreases with the in⁃crease of equivalence ratio(The following equivalence ratio is expressed byΦ),and there is a flow resistance peak in the range ofΦ=0.5~0.8.This is mainly caused by the coupling effect of high temperature physical proper⁃ties,flow rate and pressure of fuel in parallel channels.At the same time,the cooling and heat transfer character⁃istics of parallel channels under some conditions of high heat-mass ratio are obtained,and the main factors affect⁃ing the heat transfer of parallel channels such as improving surface roughness and strengthening heat transfer are mastered.In the experiment,whenΦis less than 0.9,the phenomenon of local heat transfer enhancement and deterioration can be obviously observed,and the temperature rise of local structures exceeds 200℃,which is the risk of structural damage.Therefore,the reliability of long-term parallel channel structure under the condition of high heat-mass ratio should be fully considered in structural design.

Influence of laser shock peening on microstructure and high-temperature oxidation resistance of Ti45Al8Nb alloy fabricated via laser melting deposition

Laser shock peening(LSP)was used to enhance the high-temperature oxidation resistance of laser melting deposited Ti45Al8Nb alloy.The microstructure and high-temperature oxidation behavior of the as-deposited Ti45Al8Nb alloy before and after LSP were investigated by scanning electron microscopy,X-ray diffraction,and electron backscatter diffraction.The results indicated that the rate of mass gain in the as-deposited sample after LSP exhibited a decrease when exposed to an oxidation temperature of 900℃,implying that LSP-treated samples exhibited superior oxidation resistance at high temperatures.A gradient structure with a fine-grain layer,a deformed-grain layer,and a coarse-grain layer was formed in the LSP-treated sample,which facilitated the diffusion of the Al atom during oxidation,leading to the formation of a dense Al_(2)O_(3)layer on the surface.The mechanism of improvement in the oxidation resistance of the as-deposited Ti45Al8Nb alloy via LSP was discussed.

Corrosion resistance and antibacterial properties of Ti−3Cu alloy prepared by selective laser melting

The corrosion resistance and antibacterial properties of Ti−3Cu alloy prepared by selective laser melting were evaluated using electrochemical experiments and a variety of antibacterial characterization.It is found that the charge transfer resistance of Ti−3Cu alloy was 4.89×10^(5)Ω∙cm^(2),which was doubled the data obtained by CP-Ti alloy.The antibacterial rates of Ti−3Cu alloy against S.mutans and P.gingivalis were 45.0%and 54.5%.And the antibacterial rates increased with the prolongation of cultivation time,reaching up to 62.8%and 68.6%,respectively.The in-situ nano Ti_(2)Cu precipitates were homogeneously distributed in the matrix of the Ti−3Cu alloy,which was the key reason of increasing the corrosion resistance.Additionally,the microscale electric fields between theα-Ti matrix and the Ti_(2)Cu was responsible for the enhancement of the antibacterial properties.

Selenoprotein P1 as a biomarker of insulin resistance in pediatric obesity:Insights and implications

This editorial discusses the findings of Elbarky et al on the role of selenoprotein P1(SEPP1)in pediatric obesity and insulin resistance.Their study uncovered si-gnificantly lower SEPP1 Levels in children who were obese compared with hea-lthy peers,demonstrating a negative correlation between SEPP1 levels and mea-sures of adiposity and insulin resistance.These findings suggest that SEPP1 is a biomarker useful in the early identification of insulin resistance in pediatric populations.This editorial emphasizes the clinical implications of the study and calls for further research to validate and explore the role of SEPP1 in metabolic health.

Efficacy of antimicrobials in preventing resistance in solid organ transplant recipients:A systematic review of clinical trials

BACKGROUND In the absence of effective antimicrobials,transplant surgery is not viable,and antirejection immunosuppressants cannot be administered,as resistant infections compromise the life-saving goal of organ transplantation.AIM To evaluate the efficacy of antimicrobials in preventing resistance in solid organ transplant recipients.METHODS A systematic review was conducted using a search methodology consistent with the preferred reporting items for systematic reviews and meta-analyses.This review included randomized clinical trials that evaluated the efficacy of antimicrobial agents(prophylactic or therapeutic)aimed at preventing antimicrobial resistance.The search strategy involved analyzing multiple databases,including PubMed/MEDLINE,Web of Science,Embase,Scopus,and SciELO,as well as examining gray literature sources on Google Scholar.A comprehensive electronic database search was conducted from the databases’inception until May 2024,with no language restrictions.RESULTS After the final phase of the eligibility assessment,this systematic review ultimate-ly included 7 articles.A total of 2318 patients were studied.The most studied microorganisms were cytomegalovirus,although vancomycinresistant enterococci,Clostridioides difficile,and multidrug-resistant Enterobacterales were also analyzed.The antimicrobials used in the interventions were mainly maribavir,valganciclovir,gancic-lovir,and colistin-neomycin.Of concern,all clinical trials showed significant proportions of resistant microorga-nisms after the interventions,with no statistically significant differences between the groups(mean resistance 13.47%vs 14.39%),except for two studies that demonstrated greater efficacy of maribavir and valganciclovir(mean resistance 22.2%vs 41.1%in the control group;P<0.05).The total reported deaths in three clinical trials were 75,and there were 24 graft rejections in two studies.CONCLUSION All clinical trials reported significant proportions of antimicrobial-resistant microorganisms following interventions.More high-quality randomized clinical trials are needed to corroborate these results.

Research Progress of Massage Therapy for Obesity-Induced Insulin Resistance

By searching the relevant literature in recent ten years,this paper summarizes the research progress of massage in the treatment of obesity-induced insulin resistance,in order to provide more basis for massage in the treatment of obesity-induced insulin resistance.

An integrated physiology and proteomics analysis reveals the response of wheat grain to low temperature stress during booting

Low temperature(LT)in spring has become one of the principal abiotic stresses that restrict the growth and development of wheat.Diverse analyses were performed to investigate the mechanism underlying the response of wheat grain development to LT stress during booting.These included morphological observation,measurements of starch synthase activity,and determination of amylose and amylopectin content of wheat grain after exposure to treatment with LT during booting.Additionally,proteomic analysis was performed using tandem mass tags(TMT).Results showed that the plumpness of wheat grains decreased after LT stress.Moreover,the activities of sucrose synthase(SuS,EC 2.4.1.13)and ADP-glucose pyrophosphorylase(AGPase,EC 2.7.7.27)exhibited a significant reduction,leading to a significant reduction in the contents of amylose and amylopectin.A total of 509 differentially expressed proteins(DEPs)were identified by proteomics analysis.The Gene Ontology(GO)enrichment analysis showed that the protein difference multiple in the nutritional repository activity was the largest among the molecular functions,and the up-regulated seed storage protein(ssP)played an active role in the response of grains to LT stress and subsequent damage.The Kyoto Encyclopedia of Genes and Genomes(KEGG)enrichment analysis showed that LT stress reduced the expression of DEPs such as sucrose phosphate synthase(SPS),glucose-1-phosphate adenylyltransferase(glgC),andβ-fructofuranosidase(FFase)in sucrose and starch metabolic pathways,thus affecting the synthesis of grain starch.In addition,many heat shock proteins(HsPs)were found in the protein processing in endoplasmic reticulum pathways,which can resist some damage caused by LT stress.These findings provide a new theoretical foundation for elucidating the underlying mechanism governing wheat yield developmentafterexposuretoLTstress inspring.