Influence of bias voltage and oxygen addition on the discharge aspects of a diffuse argon plume in an atmospheric pressure plasma jet

A remote plasma,also referred to as a plasma plume(diffuse or filamentary),is normally formed downstream of an atmospheric pressure plasma jet.In this study,a diffuse plume is formed by increasing the bias voltage(U_(b))applied to the downstream electrode of an argon plasma jet excited by a negatively pulsed voltage.The results indicate that the plume is filamentary when U_(b)is low,which transits to the diffuse plume with increasing U_(b).The discharge initiated at the rising edge of the pulsed voltage is attributed to the diffuse plume,while that at the falling edge contributes to the filament in the plume.For the diffuse plume,the discharge intensity decreases with the increasing oxygen content(C_o).Fast photography reveals that the diffuse plume results from a negative streamer,which has a dark region near the nozzle with C_o=0%.However,the dark region is absent with C_o=0.5%.From the optical emission spectrum,the electron density,electron excitation temperature,gas temperature,and oxygen atom concentration are investigated.

Three different low-temperature plasma-based methods for hydrophilicity improvement of polyethylene films at atmospheric pressure

Three different low-temperature plasma-based methods were used to improve the surface hydrophilicity of polyethy- lene （PE） films, and all the modification processes were carried out by employing an atmospheric pressure plasma jet （APPJ） system. （a） PE films were directly modified by APPJ using a gas mixture of He and 02. （b） Acrylic acid （AA） was introduced into the system and a polymer acrylic acid （PAA） coating was deposited onto the PE films. （c） AA was grafted onto the PE surface activated by plasma pre-treatment. It was found that the hydrophilicity of the PE films was significantly improved for all the three methods. However, the samples modified by Process （a） showed hydrophobicity recovery after a storage time of 20 days while no significant change was found in samples modified by Process （b） and Process （c）. The Fourier transform infrared spectroscopy （FTIR） results indicated that the most intensive C=O peak was detected on the PE surface modified by Process （c）. According to the X-ray photoelectron spectroscopy （XPS） analysis, the ratios of oxygen-containing polar groups for samples modified by Process （b） and Process （c） were higher than that modified by Process （a）.

Surface Decontamination of Chemical Agent Surrogates Using an Atmospheric Pressure Air Flow Plasma Jet

An atmospheric pressure dielectric barrier discharge （DBD） plasma jet generator using air flow as the feedstock gas was applied to decontaminate the chemical agent surrogates on the surface of aluminum, stainless steel or iron plate painted with alkyd or PVC. The experi- mental results of material decontamination show that the residual chemical agent on the material is lower than the permissible value of the National Military Standard of China. In order to test the corrosion effect of the plasma jet on different material surfaces in the decontamination pro-cess, corrosion tests for the materials of polymethyl methacrylate, neoprene, polyvinyl chloride （PVC）, polyethylene （PE）, phenolic resin, iron plate painted with alkyd, stainless steel, aluminum, etc. were carried out, and relevant parameters were examined, including etiolation index, chroma- tism, loss of gloss, corrosion form, etc. The results show that the plasma jet is slightly corrosive for part of the materials, but their performances are not affected. A portable calculator, computer display, mainboard, circuit board of radiogram, and a hygrometer could work normally after being treated by the plasma jet.

Study of generation characteristics of glow-type atmospheric-pressure plasma jet based on DC discharge in air

In order to form an atmospheric-pressure plasma jet without airflow, a needle–ring electrode structure is proposed in this paper. When heteropolar potentials are applied to a needle and a ring, a marked electric field strength enhancement around the needle’s pointed end has been found. When the same potential is applied to both the needle and the ring, the lateral electric field strength for the needle can be weakened. By using the above two methods, an increase of the difference between the pointed end electric field strength and the lateral one is achieved and stable plasma jets are formed. A symmetrical space electric field distribution is established at the pointed end of the needles when several sets of heteropolar needle–ring electrodes are uniformly arranged, which is conducive to forming a uniform array plasma jet. Under DC discharge conditions, a safe and stable plasma jet of high density and an array plasma jet are successfully achieved.

Spectral Diagnosis of Gas Temperature of Atmospheric Pressure Plasma Jet in Helium

For atmospheric pressure plasma jets(APPJ),the gas temperature is essential for their applications.A spectral diagnosis of APPJ’s gas temperature is conducted in this work.The optical emission spectra of helium APPJ are captured by using an optical spectrometer system.Then,the grating secondary spectrum of OH(A2∑+(ν=0)→X2П(ν=0))are used to diagnose the gas temperature of plasmas because the spectrum has excellent resolution.Meanwhile,the vibrational temperatures are estimated by using the vibration sequence of N2band(SPS,the second positive system).On the basis of the method,some important conclusions were obtained.First,the spectral identifying indicates that the grating primary spectrum covers a whole wavelength range from 200 nm to 900 nm,and that the grating secondary spectrum overlaps with the primary spectrum from 400 nm to 900 nm.Second,the gas temperature(about 320 K)is close to the room temperature,while the vibrational temperature of the N2(SPS)is about 5 000 K.The trend of the two temperatures changing with the applied voltage is discussed in the end.

Characteristics of Low Power CH_4/Air Atmospheric Pressure Plasma Jet

A low power atmospheric pressure plasma jet driven by a 24 kHz AC power source and operated with a CH4/air gas mixture has been investigated by optical emission spectrometer. The plasma parameters including the electron excitation temperature, vibrational temperature and rotational temperature of the plasma jet at different discharge powers are diagnosed based on the assumption that the kinetic energy of the species obeys the Boltzmann distribution. The electron density at different power is also investigated by HS Stark broadening. The results show that the plasma source works under non-equilibrium conditions. It is also found that the vibrational temperature and rotational temperat;ure increase with discharge power, whereas the electron excitation temperature seems to have a downward trend. The electron density increases from 0.8×10^21 m^-3 to 1.1×10^21 m^-3 when the discharge power increases from 53 W to 94 W.

Atmospheric Pressure Plasma Jet in Organic Solution:Spectra,Degradation Effects of Solution Flow Rate and Initial pH Value

The organic compounds of p-nitrophenol （PNP） solution was treated by the active species generated in a stirred reactor by an atmospheric pressure plasma jet （APPJ）. The emission intensities of hydroxyl （OH）, oxygen （O）, nitric oxide （NO）, hydrogen （H） and molecular （N2） were measured by optical emission spectroscopy （OES）. The relations between the flow rates of the PNP solution and degradation, the degradation effects and initial pH value of the solution were also investigated. Experimental results show that there exist intense emissions of O （777.1 nm）, N（337.1 nm）, OH （306-310 nm） and NO band （200-290 nm） in the region of plasma. Given the treatment time and gas flow rate, the degradation increased as a function of discharge energy and solution flow rate, respectively. The solution flow rate for the most efficient degradation ranged from 1.414 m/s to 1.702 m/s, and contributed very little when it exceeded 2.199 m/s. This indicates the existence of diffusion-controlled reactions at a low solution flow rate and activation- controlled reactions at a high solution flow rate. Moreover, increasing or decreasing the initial pH value of neutral PNP solution （pH=5.95） could improve the degradation efficiency. Treated by APPJ, the PNP solutions with different initial pH values of 5.95, 7.47 and 2.78 turned more acidic in the end, while the neutral solution had the lowest degradation efficiency. This work clearly demonstrates the close coupling of active species, photolysis of ultraviolet, the organic solution flow rate and the initial pH value, and thus is helpful in the study of the mechanism and application of plasma in wastewater treatment.

Polymer Surface Treatment by Atmospheric Pressure Low Temperature Surface Discharge Plasma:Its Characteristics and Comparison with Low Pressure Oxygen Plasma Treatment

The polymer treatment with a low-temperature plasma jet generated on the atmospheric pressure surface discharge （SD） plasma is performed. The change of the surface property over time, in comparison with low pressure oxygen （O2） plasma treatment, is examined. As one compares the treatment by atmospheric pressure plasma to that by the low pressure O2 plasma of PS （polystyrene） the treatment effects were almost in complete agreement. However, when the atmospheric pressure plasma was used for PP（polypropylene）, it produced remarkable hydrophilic effects.

Two-dimensional numerical study of an atmospheric pressure helium plasma jet with dual-power electrode

In this paper, the characteristics of an atmospheric pressure helium plasma jet generated by a dual-power electrode （DPE） configuration are investigated by using a two-dimensional fluid model. The effect of a needle electrode on the discharge is studied by comparing the results of the DPE configuration with those of the single ring electrode configuration. It is found that the existence of the needle leads to the generation of a helium plasma jet with a higher propagation velocity, higher species density, and larger discharge width. Furthermore, the influences of the needle radius and needle-to-ring discharge gap on the generation of a plasma jet are also studied. The simulation results indicate that the needle electrode has an evident influence on the plasma jet characteristics.

Bacteria Inactivation Using DBD Plasma Jet in Atmospheric Pressure Argon

A coaxial dielectric barrier discharge plasma jet was designed, which can be operated in atmospheric pressure argon under an intermediate frequency sinusoidal resonant power supply, and an atmospheric pressure glow-like discharge was achieved. Two kinds of typical bacteria, i.e., the Staphylococcus aureus （S. aureus） and Escherichia coil （E. coil）, were employed to study the bacterial inactivation mechanism by means of the non-thermal plasma. The killing log value （KLV） of S. aureus reached up to 5.38 with a treatment time of 90 s and that of E. coil up to 5.36 with 60 s, respectively. According to the argon emission spectra of the plasma jet and the scanning electron microscope （SEM） images of the two bacteria before and after the plasma treatment, it is concluded that the reactive species in the argon plasma played a major role in the bacterial inactivation, while the heat, electric field and UV photons had little effect.

Study on an Atmospheric Pressure Plasma Jet and its Application in Etching Photo-Resistant Materials

An atmospheric pressure radio-frequency plasma jet that can eject cold plasma has been developed. In this paper, the configuration of this type of plasma jet is illustrated and its discharge characteristics curves are studied with a current and a voltage probe. A thermal couple is used to measure the temperature distribution along the axis of the jet stream. The temperature distribution curve is generated for the He/O-2 jet stream at the discharge power of 150 W. This jet can etch the photo-resistant material at an average rate of 100 nm/min on the surface of silicon wafers at a right angle.

Atmospheric Pressure Plasma Jet in Ar and O_2/Ar Mixtures:Properties and High Performance for Surface Cleaning

An atmospheric pressure plasma jet generated in Ar and O2/Ar mixtures has been investigated by specially designed equipment with double power electrodes at 20~32 kHz, and their effects on the cleaning of surfaces have been studied. Properties of the jet discharge are studied by electrical diagnostics, including the waveform of discharge voltage, discharge current and the Q-V Lissajous figures. The optical emission spectroscopy is used to measure the plasma parameters, such as the excitation temperature and the gas temperature. It is found that the consumed power and the excitation temperature increase with increase of the discharge frequency. On the other hand, at the same discharge frequency, these parameters in O2/Ar mixture plasma are found to be much larger. The effect on surface cleaning is studied from the changes in the contact angle. For Ar plasma jet, the contact angle decreases with increase of the discharge frequency. For O2/Ar mixture plasma jet, the contact angle decreases with increase of discharge frequency up to 26 kHz, however, further increase of discharge frequency does not show further decrease in the contact angle. At the same discharge frequency, the contact angle after O2/Ar mixture plasma cleaning is found to be much lower compared to the case of pure Ar. From the results of quadrupole mass-spectrum analysis, we can identify more fragment molecules of CO and H2O in the emitted gases after O2/Ar plasma jet treatment compared with Ar plasma jet treatment, which are produced by the decomposition of surface organic contaminants during the cleaning process.

Comparison of Sterilizing Effect of Nonequilibrium Atmospheric-Pressure He/O_2 and Ar/O_2 Plasma Jets

The sterilizing effect of the non-equilibrium atmospheric pressure plasma jet by applying it to the Bacillus subtilis spores is invesigated. A stable glow discharge in argon or helium gas fed with active gas （oxygen）, was generated in the coaxial cylindrical reactor powered by the radio-frequency power supply at atmospheric pressure. The experimental results indicated that the efficiency of killing spores by making use of an Ar/O2 plasma jet was much better than with a He/O2 plasma jet. The decimal reduction value of Ar/O2 and He/O2 plasma jets under the same experimental conditions was 4.5 seconds and 125 seconds, respectively. It was found that there exists an optimum oxygen concentration for a certain input power, at which the sterilization efficiency reaches a maximum value. It is believed that the oxygen radicals are generated most efficiently under this optimum condition.

Development of a new atmospheric pressure cold plasma jet generator and application in sterilization

This paper reports that a new plasma generator at atmospheric pressure, which is composed of two homocentric cylindrical all-metal tubes, successfully generates a cold plasma jet. The inside tube electrode is connected to ground, the outside tube electrode is connected to a high-voltage power supply, and a dielectric layer is covered on the outside tube electrode. When the reactor is operated by low-frequency （6 kHz-20 kHz） AC supply in atmospheric pressure and argon is steadily fed as a discharge gas through inside tube electrode, a cold plasma jet is blown out into air and the plasma gas temperature is only 25-30℃. The electric character of the discharge is studied by using digital real-time oscilloscope （TDS 200-Series）, and the discharge is capacitive. Preliminary results are presented on the decontamination of E.colis bacteria and Bacillus subtilis bacteria by this plasma jet, and an optical emission analysis of the plasma jet is presented in this paper. The ozone concentration generated by the plasma jet is 1.0× 10^16cm^-3 which is acquired by using the ultraviolet absorption spectroscopy.

A two-dimensional air streamer discharge modified model based on artificial stability term under non-uniform electric field at low temperature and sub-atmospheric pressure

In this paper, an improved air discharge fluid model under non-uniform electric field is constructed based on the plasma module COMSOL Multiphysics with artificial stability term, and the boundary conditions developed in the previous paper are applied to the calculation of photoionization rate. Based on the modified model, the characteristics of low temperature subatmospheric air discharge under 13 kV direct current voltage are discussed, including needle-plate and needle-needle electrode structures. Firstly, in order to verify the reliability of the model, a numerical example and an experimental verification were carried out for the modified model respectively. Both verification results show that the model can ensure the accuracy and repeatability of the calculation. Secondly, according to the calculation results of the modified model, under the same voltage and spacing, the reduced electric field under low temperature subatmosphere pressure is larger than that under normal temperature and atmospheric pressure. The high electric field leads to the air discharge at low temperature and sub atmospheric pressure entering the streamer initiation stage earlier, and has a faster propagation speed in the streamer development stage, which shortens the overall discharge time. Finally, the discharge characteristics of the two electrode structures are compared, and it is found that the biggest difference between them is that there is a pre-ionization region near the cathode in the needle-needle electrode structure. When the pre-ionization level reaches 1013 cm-3, the propagation speed of the positive streamer remains unchanged throughout the discharge process, and is no longer affected by the negative streamer. The peak value of electric field decreases with the increase of pre-ionization level, and tends to be constant during streamer propagation. Based on the previous paper, this paper constructs the air discharge model under non-uniform electric field, complements with the previous paper, and forms a relatively complete set of air discharge simulation system under low temperature and sub atmospheric pressure, which provides a certain reference for future research.

The interaction of an atmospheric pressure plasma jet using argon or argon plus hydrogen peroxide vapour addition with bacillus subtilis

This paper reports that an atmospheric pressure dielectric barrier discharge plasma jet, which uses argon or argon ＋ hydrogen peroxide vapour as the working gas, is designed to sterilize the bacillus subtilis. Compared with the pure argon plasma, the bacterial inactivation efficacy has a significant improvement when hydrogen peroxide vapour is added into the plasma jet. In order to determine which factors play the main role in inactivation, several methods are used, such as determination of optical emission spectra, high temperature dry air treatment, protein leakage quantification, and scanning electron microscope. These results indicate that the possible inactivation mechanisms are the synergistic actions of chemically active species and charged species.

Influence of Additive Gas on Electrical and Optical Characteristics of Non-equilibrium Atmospheric Pressure Argon Plasma Jet

Electrical and optical properties of an argon plasma jet were characterized. In particular, effects of an additive gas, namely nitrogen or oxygen, on these properties were studied in detail. The plasma jet was found to be of a glow-like discharge, which scarcely changed upon the injection of an additive gas, either directly or through a glass capillary. Optical emission spectroscopy characterization revealed that excited argon atoms were the predominant active species in this plasma jet. Metastable argon atoms were highly quenched, and N2（C3yIu） became the main energy carrier following nitrogen injection. When oxygen was added to the afterglow zone through a glass capillary, no significant quenching effect was observed and the number of oxygen atoms decreased with the increase in oxygen concentration. Finally, to demonstrate an application of this plasma jet, a high-density polyethylene surface was treated with argon, argon/nitrogen, and argon/oxygen plasmas.

Numerical study of the effect of water content on OH production in a pulsed-dc atmospheric pressure helium–air plasma jet

A numerical study of the effect of water content on OH production in a pulsed-dc atmospheric pressure helium-air plasma jet is presented. The generation and loss mechanisms of the OH radicals in a positive half-cycle of the applied voltage are studied and discussed. It is found that the peak OH density increases with water content in air （varying from 0% to 1%） and reaches 6.3 x 10^18 m-3 when the water content is 1%. Besides, as the water content increases from 0.01% to 1%, the space-averaged reaction rate of three-body recombination increases dramatically and is comparable to those of main OH generation reactions.

An Indirect Method for Measuring Electron Density of Atmospheric Pressure Plasma Jets

An indirect method for measuring the electron density of radio frequency atmospheric pressure plasma jets （RF-APPJ） based on the discharge voltage and current waveforms is presented. An equivalent circuit of the plasma discharge is assumed by taking into account the electrode capacitance, serial resistance and inductance of the bulk plasma, as well as the sheath impedance. Based on the circuit model, the electron density can be obtained according to Ohm＇s law. By using this method, the effects of the electrode shape and discharge gap on the electron density are discussed.

Characteristics of a kHz helium atmospheric pressure plasma jet interacting with two kinds of targets

This study investigates the influence of two types of target,skin tissue and cell culture medium,with different permittivities on a k Hz helium atmospheric pressure plasma jet(APPJ)during its application for wound healing.The basic optical-electrical characteristics,the initiation and propagation and the emission spectra of the He APPJ under different working conditions are explored.The experimental results show that,compared with a jet freely expanding in air,the diameter and intensity of the plasma plume outside the nozzle increase when it interacts with the pigskin and cell culture medium targets,and the mean velocity of the plasma bullet from the tube nozzle to a distance of 15 mm is also significantly increased.There are also multiple increases in the relative intensity of OH(A^(2)Σ→X^(2)Π)and O(3p^(5)S-3s^(5)S)at a position 15 mm away from nozzle when the He APPJ interacts with cell culture medium compared with the air and pigskin targets.Taking the surface charging of the low permittivity material capacitance and the strengthened electric field intensity into account,they make the various characteristics of He APPJ interacting with two different targets together.