Control system design for a pressure-tube-type supercritical water-cooled nuclear reactor via a higher order sliding mode method

Nuclear power plants exhibit non-linear and time-variable dynamics.Therefore,designing a control system that sets the reactor power and forces it to follow the desired load is complicated.A supercritical water reactor(SCWR)is a fourth-generation conceptual reactor.In an SCWR,the non-linear dynamics of the reactor require a controller capable of control-ling the nonlinearities.In this study,a pressure-tube-type SCWR was controlled during reactor power maneuvering with a higher order sliding mode,and the reactor outgoing steam temperature and pressure were controlled simultaneously.In an SCWR,the temperature,pressure,and power must be maintained at a setpoint(desired value)during power maneuvering.Reactor point kinetics equations with three groups of delayed neutrons were used in the simulation.Higher-order and classic sliding mode controllers were separately manufactured to control the plant and were compared with the PI controllers speci-fied in previous studies.The controlled parameters were reactor power,steam temperature,and pressure.Notably,for these parameters,the PI controller had certain instabilities in the presence of disturbances.The classic sliding mode controller had a higher accuracy and stability;however its main drawback was the chattering phenomenon.HOSMC was highly accurate and stable and had a small computational cost.In reality,it followed the desired values without oscillations and chattering.

North Pacific Eastern Subtropical Mode Water simulation and future projection

The present climate simulation and future projection of the Eastern Subtropical Mode Water （ESTMW） in the North Pacific are investigated based on the Geophysical Fluid Dynamics Laboratory Earth System Model （GFDL-ESM2M）. Spatial patterns of the mixed layer depth （MLD） in the eastern subtropical North Pacific and the ESTMW are well simulated using this model. Compared with historical simulation, the ESTMW is produced at lighter isopycnal surfaces and its total volume is decreased in the RCP8.5 runs, because the subduction rate of the ESTMW decreases by 0.82×10？6 m/s during February–March. In addition, it is found that the lateral induction decreasing is approximately four times more than the Ekman pumping, and thus it plays a dominant role in the decreased subduction rate associated with global warming. Moreover, the MLD during February–March is banded shoaling in response to global warming, extending northeastward from the east of the Hawaii Islands （20°N, 155°W） to the west coast of North America （30°N, 125°W）, with a max-imum shoaling of 50 m, and then leads to the lateral induction reduction. Meanwhile, the increased north-eastward surface warm current to the east of Hawaii helps strengthen of the local upper ocean stratification and induces the banded shoaling MLD under warmer climate. This new finding indicates that the ocean surface currents play an important role in the response of the MLD and the ESTMW to global warming.

Response of Mode Water and Subtropical Countercurrent to Greenhouse Gas and Aerosol Forcing in the North Pacific

The response of the North Pacific Subtropical Mode Water and Subtropical Countercurrent (STCC) to changes in greenhouse gas (GHG) and aerosol is investigated based on the 20th-century historical and single-forcing simulations with the Geo-physical Fluid Dynamics Laboratory Climate Model version 3 (GFDL CM3). The aerosol effect causes sea surface temperature (SST) to decrease in the mid-latitude North Pacific, especially in the Kuroshio Extension region, during the past five decades (1950-2005), and this cooling effect exceeds the warming effect by the GHG increase. The STCC response to the GHG and aerosol forcing are opposite. In the GHG (aerosol) forcing run, the STCC decelerates (accelerates) due to the decreased (increased) mode waters in the North Pacific, resulting from a weaker (stronger) front in the mixed layer depth and decreased (increased) subduction in the mode water formation region. The aerosol effect on the SST, mode waters and STCC more than offsets the GHG effect. The response of SST in a zonal band around 40?N and the STCC to the combined forcing in the historical simulation is similar to the response to the aerosol forcing.

Variability of subduction rates of the subtropical North Pacific mode waters

The climatology subduction rate for the entire Pacific is known, but the mechanism of interannual to decadal variation remains unclear. In this study, we calculated the annual subduction rates of three types of North Pacific subtropical mode waters using a general circulation model (LICOM1.0) for the period of 1958-2001. The model experiments focused on interannual variations of ocean dynamical processes under daily wind forcings and seasonal heat fluxes. The mode water formation region was defined by a potential vorticity minimum at outcrop locations. The model results show that two subduction rate maxima (>100 m/a) were located in the Subtropical Mode Water (STMW) and the Central Mode Water (CMW) formation regions. These regions are consistent with a climatologically calculated value. The subduction rate in the Eastern Subtropical Mode Water (ESTMW) formation region was smaller at about 75 m/a. The subduction rate shows clear interannual and decadal variations associated with oceanic dynamic variabilities. The average subduction rate of the STMW was much smaller during the period of 1981-1990 compared with other periods, while that of the CMW had a negative anomaly before 1975 and a positive anomaly after 1978. The variability agreed with Ekman and geostrophic advections and mixed layer depths. The interannual variability of the subduction rate for the ESTMW was smallest during 1970-1990, as a result of a weak wind stress curl. This paper explores how interannual signals from the atmosphere are stored in different parts of the ocean, and thus may contribute to a better understanding of feedback mechanisms for the Pacific Decadal Oscillation (PDO) event.

Failure mode and dynamic response of a double-sided slope with high water content of soil

A double-sided slope with high water content in sandy clay was considered under the action of seismic load. Its failure mode and dynamic response were investigated using a hydraulic servo shaking table test. The typical characteristic of failure mode and dynamic responses of the double-sided slope were analyzed. Experimental results show that slope failure undergoes a process of progressive deformation. The slope failure mode can be explained as creep sliding landslide. AFA(Amplification Factor of Acceleration) at the surface and inner parts of the slope shows an increasing trend with the increase of relative elevation. The relationship between AFA and EAA(Excitation Amplitude of Acceleration) is nonlinear. An empirical formula is proposed to describe preferably the relationship between AFA,relative elevation and dimensionless EAA. The AFA at the middle and upper parts of the slope increases apparently with increasing EFA(Excitation Frequency of Acceleration).

Response of North Pacific Eastern Subtropical Mode Water to Greenhouse Gas Versus Aerosol Forcing

Mode water is a distinct water mass characterized by a near vertical homogeneous layer or low potential vorticity, and is considered essential for understanding ocean climate variability. Based on the output of GFDL CM3, this study investigates the response of eastern subtropical mode water （ESTMW） in the North Pacific to two different single forcings： greenhouse gases （GHGs） and aerosol. Under GHG forcing, ESTMW is produced on lighter isopycnal surfaces and is decreased in volume. Under aerosol forcing, in sharp contrast, it is produced on denser isopycnal surfaces and is increased in volume. The main reason for the opposite response is because surface ocean-to-atmosphere latent heat flux change over the ESTMW formation region shoals the mixed layer and thus weakens the lateral induction under GHG forcing, but deepens the mixed layer and thus strengthens the lateral induction under aerosol forcing. In addition, local wind changes are also favorable to the opposite response of ESTMW production to GHG versus aerosol.

Fast and Slow Responses of the North Pacific Mode Water and Subtropical Countercurrent to Global Warming

Six coupled general circulation models from the Coupled Model Intercomparison Project Phase 5 (CMIP5) are em-ployed for examining the full evolution of the North Pacific mode water and Subtropical Countercurrent (STCC) under global warming over 400 years following the Representative Concentration Pathways (RCP) 4.5. The mode water and STCC first show a sharp weakening trend when the radiative forcing increases, but then reverse to a slow strengthening trend of smaller magnitude after the radiative forcing is stablized. As the radiative forcing increases during the 21st century, the ocean warming is surface-intensified and decreases with depth, strengthening the upper ocean's stratification and becoming unfavorable for the mode water formation. Moving southward in the subtropical gyre, the shrinking mode water decelerates the STCC to the south. After the radiative forcing is stabilized in the 2070s, the subsequent warming is greater at the subsurface than at the sea surface, destabilizing the upper ocean and becoming favorable for the mode water formation. As a result, the mode water and STCC recover gradually after the radiative forc-ing is stabilized.

Nitrogen and Phosphorus Loss Law and Emission Reduction Effects Under Water and Fertilizer Management Integrated Mode in Dike Paddy Field

To achieve the purpose of reducing farm non-point source pollution, we integrated site specific nitrogen management precise irrigation, controlled drainage, and wetland eco-repair system in dike area of Taihu basin. During investigation, it had given prominence for the water and fertilizer coupling effects of precise irrigation and site specific nutrient management, the characteristics of integration on controlled irrigation, controlled drainage and wetland ecosystem non-point source pollution control. Then the water and fertilizer integrated management mode of paddy field was put forward in Taihu basin where the water production efficiency increased to 1.64 kg. m-3, water saved 37.8%, fertilizer use efficiency raised 15,4%, yield raised 10%, and N, P load decreased 26%-72%. The modern agricultural and farmland ecosystems that control and cut down the farm non-point source pollution came into being, which can be a reference by Taihu basin to control its agricultural non-point source pollution and eutrophicated water body.

Recent Advances in Studies on Formation Mechanism of Subtropical Mode Water and Its Climate Features in North Pacific

Mode Water’, as a product of air-sea interaction, influences the thermal structure and circulation pattern in upper layer ocean and consequently affects the variations of climate. In this paper the recent research results about the subtropi-cal Mode Water in the North Pacific are overiewed. A detailed description of the three kinds of Mode Water in the subtropical North Pacific and some comparisons of their similarities and differences are introduced. Some science problems that need further exploration have been raised.

Subtropical Mode Water in the Northwestern Pacific

Based on the in situ XBT and other data sets, by analyzing the seasonal cycle of the mixed layer depth (MLD) and using the conservative potential vorticity (PV) as a tool, a clear description of the formation process of the North Pacific Subtropical Mode Water (NPSTMW) is presented for explaining the well known 'Stommel Demon'. The forming of NPSTMW reflects well the ventilation process of the isotherms of the permanent thermocline. The formation process can be divided into the 'ventilation' phase and the 'formation' phase. In the first phase (October-March), with large heat losses at the sea surface from October, the mixed layer deepens and correspondingly, the water mass with low PV emerges and sinks. After continual cooling from October to March, the mixed layer reaches its maximum value ( >300 m) in March. Then, in the second phase (April-June), the mixed layer shoals rapidly from April, a large part of the low PV water mass is sheltered from further air-sea interaction by the emerging seasonal thermocline, and thus forms new NPSTMW. Further analysis indicates that the formation region of warm NPSTMW (17-18℃) is limited between 140°-150°E, while the relatively cold NPSTMW (16-17℃) originates in a wider longitude range (140°-170°E).Climate features of NPSTMW are presented with the use of climatological Levitus (1994 a, b) dataset. It is shown that NPSTMW lies in the region of (130°-170°E, 22°-34°N) with core temperature ranging from about 16-19℃ and potential density around 25-25.8σθ NPSTMW has a three-dimensional structure lying below the seasonal thermocline (about 100 m deep) and reaches almost to 350m depths.

A study of Indian Ocean Subtropical Mode Water: subduction rate and water characteristics

The annual subduction rate in the South Indian Ocean was calculated by analyzing Simple Ocean Data Assimilation （SODA） outputs in the period of 1950-2008. The subduction rate census for potential density classes showed a peak corresponding to Indian Ocean subtropical mode water （IOSTMW） in the southwestern part of the South Indian Ocean subtropical gyre. The deeper mixed layer depth, the sharper mixed-layer fronts and the associated relatively faster circulation in the present climatology resulted in a larger lateral induction, which primarily dominants the IOSTMW subduction rate, while with only minor contribution from vertical pumping. Without loss of generality, through careful analysis of the water characteristics in the layer of minimum vertical temperature gradient （LMVTG）, the authors suggest that the IOSTMW was identified as a thermostad, with a lateral minimum of low potential vorticity （PV, less than 200× 10^-12 m^-1·s^-1） and a low dT/dz （less than 1.5℃/（100 m））. The IOSTMW within the South Indian Ocean subtropical gyre distributed in the region approximately from 25° to 50° E and from 30° to 39°S. Additionally, the average characteristics （temperature, salinity, potential density） of the mode water were estimated about （16.38 ± 0.29）℃, （35.46 ±0.04）, （26.02 ±0.04） ae over the past 60 years.

Contribution of Mesoscale Eddies to the Subduction and Transport of North Pacific Eastern Subtropical Mode Water

This study investigates the contribution of mesoscale eddies to the subduction and transport of North Pacific Eastern Subtropical Mode Water(ESTMW)using the high-frequency output of an eddy-resolved ocean model spanning the period 1994–2010.Results show that the subduction induced by mesoscale eddies accounts for about 31%of the total subduction of ESTMW formation.The volume of ESTMW trapped by anticyclonic eddies is slightly larger than that trapped by cyclonic eddies.The ESTMW trapped by all eddies in May reaches up to about 2.8×1013m3,which is approximately 16%of the total ESTMW volume.The eddy-trapped ESTMW moves primarily westward,with its meridional integration at 18°–30°N reaching about 0.17Sv,which is approximately 18%of the total zonal ESTMW transport in this direction,at 140°W.This study highlights the important role of eddies in carrying ESTMW westward over the northeastern Pacific Ocean.

Investigation of hydroxyl-terminated polybutadiene propellant breaking characteristics and mechanism impacted by submerged cavitation water jet

A submerged cavitation water jet(SCWJ)is an effective method to recycle solid propellant from obsolete solid engines by the breaking method.Solid propellant's breaking modes and mechanical process under SCWJ impact are unclear.This study aims to understand those impact breaking mechanisms.The hydroxyl-terminated polybutadiene(HTPB)propellant was chosen as the research material,and a self-designed test system was used to conduct impact tests at four different working pressures.The high-speed camera characterized crack propagation,and the DIC method calculated strain change during the impact process.Besides,micro and macro fracture morphologies were characterized by scanning electron microscope(SEM)and computed tomography(CT)scanning.The results reveal that the compressive strain concentration region locates right below the nozzle,and the shear strain region distributes symmetrically with the jet axis,which increases to 4% at first 16th ms,the compressive strain rises to 2% and 6% in the axial and transverse direction,respectively.The two tensile cracks formed first at the compression strain concentrate region,and there generate many shear cracks around the tensile cracks,and those shear cracks that develop and aggregate cause the cracks to become wider and cut through the tensile cracks,forming the tensile-shear cracks and the impact parts eventually fail.The HTPB propellant forms a breaking hole shaped conical after impact 10 s.The mass loss increases by 17 times at maximum,with the working pressure increasing by three times.Meanwhile,the damage value of the breaking hole remaining on the surface increases by 7.8 times while 2.9 times in the depth of the breaking hole.The breaking efficiency is closely affected by working pressures.The failure modes of HTPB impacted by SCWJ are classified as tensile crack-dominated and tensile-shear crack-dominated damage mechanisms.

Water Gauge Image Denoising Model Based on Improved Adaptive Total Variation

As an important part of water level warning in water conservancy projects,often due to the influence of environmental factors such as light and stains,the acquired water gauge images have sticky,broken and bright spot conditions,which affect the identification of water gauges.To solve this problem,a water gauge image denoising model based on improved adaptive total variation is proposed.Firstly,the regular term exponent in the adaptive total variational equation is changed to an inverse cosine function;secondly,the differential curvature is used to distinguish the image noise points and increase the smoothing strength at the noise points;finally,according to the characteristics of the gradient mode and adaptive gradient threshold after Gaussian filtering,the New model can adaptively denoise in the smooth area and protect the edge area,so as to have the characteristics of both edge-preserving denoising.The experimental results show that the new model has a great improvement in image vision,higher iteration efficiency and an average increase of 1.6 dB in peak signal-to-noise ratio,and an average increase of 9%in structural similarity,which is more beneficial to practical applications.

Covariability of Subantarctic Mode Water and the Southern Branch of the Subtropical Indian Ocean Countercurrent in Argo Observations

The Subantarctic Mode Water(SAMW)forms in the deep mixed layer north of the Antarctic Circumpolar Current and spreads northward into the subtropical gyre.The subtropical South Indian Countercurrent(SICC)flows eastward on the north flank of the thick SAMW layer within 22°-32°S from south of Madagascar at around 25°S,50°E toward western Australia.The dynamical relation of the SAMW and the southern branch of the SICC(30°-32°S)is investigated in this work based on the monthly mean Argo data from 2004 to 2019.The physical properties of the SAMW and its pathway from the formation region are described.Most of the SAMW in the Indian Ocean sector originates from the deep mixed layers of the southeastern Indian Ocean(about 40°S,85°-105°E)and moves along the subtropical gyre.It takes around ten years to arrive east of Madagascar Island preserving its low potential vor-ticity characteristics.As a thick layer with homogeneous vertical properties,the SAMW forces the upper pycnocline to shoal,and the associated eastward shear results in the surface-intensified SICC.The SAMW forms a tongue-shaped thickness pattern,which influ-ences the southern branch of the SICC above the northern flank of the thickest SAMW layer between 24°S and 32°S.The seasonal,interannual,and decade variations of the southern branch of the SICC are closely related to the meridional gradient of the underlying SAMW thickness.The SAMW thickened and strengthened from 2005 to 2015,thereby anchoring a strengthened SICC.The interan-nual covariability of the SAMW and SICC further supports the SAMW’s role in driving SICC variability.

On the Ecological Restoration Mode of Urban Water Revetment Landscape

Urban waterfront revetment is a special zone between water and land,with high ecological,economic and aesthetic value. Waterfront revetment landscape is not only an important part of urban water and land ecosystems,but also an integral part of the city. Based on the current situation of ecological environment of waterfront revetment landscape,we come up with different ecological restoration modes for different types of revetment,to achieve the organic integration of waterfront revetment landscape and ecology.

Study on the Monitoring Malfunction of Water Pollution during Drought or Flood Period and Low-carbon and High-value Methodology--A Case Study of the Correlation Test of Water,Soil and Gas Pollution in Xiangxiang County

Based on the low-carbon and high-value methodology of chemical ecology and chemical informatics,combining theory and methods,taking saving,environmental protection,low carbon,high production,high value and circulation as values and aims,the relationship between human and land as a basis,ecosystem as a center,overall control as a goal and agricultural ecological engineering as a mean,environmental pollution detection,as one of bottlenecks for agricultural products and food security,should be solved firstly;through the field survey in dry years from 2009 to 2010 when drought and flood were frequent and the frequency of drought was higher than that of flood,plus the determination of surface water flow and water quantity in a small typical river basin,the correlation of local water,soil and gas in the county could be found,and the transfer of monitoring focus from water environment to atmospheric environment was possible and necessary.The study would promote the quantitative research on the correlation among water,soil and gas,and the results were in accordance with the conclusions of related studies.

Analysis on the Hotel Management Mode from the Perspective of Low-carbon Tourism

As the global warming is becoming more and more serious, people have gradually come to realize the important role of low- carbon life. Since a strategy of sustainable development was proposed in China, the concept of low-carbon tourism has emerged, requiring tourists to carry out energy conservation and environmental protection as much as possible in the process of travel. The hotels in scenic areas naturally become an important part of tourists in travel and play a crucial role in the development of low-carbon tourism. Therefore, a deep analysis on the present hotel management mode is necessary, promoting hotels to conform to the requirements of low-carbon tourism. In this paper, hotel management is discussed from the perspective of low-carbon tourism, so as to provide ideas of practical significance and guiding role and a basis for the future low-carbon tourism and hotel management.

Rear-Surface Deformation of a Water Drop in Aero-Breakup of Shear Mode

Deformation of water drops in shock-induced high-speed flows is investigated with a focus to the influence of primitive flow parameters on the rear-surface deformation features. Two typical deformation patterns are discovered through high-speed photography. A simple equation to evaluate the radial acceleration of the drop surface is derived. The combined use of this equation and outer flow simulation makes it possible for us to reconstruct the profiles of the early deformed drops. The results agree well with the experiments. Further analysis shows that the duration of flow establishment with respect to the overall breakup time shapes the rear side profile of the drop. Thereby the ratio of the two times, expressed as the square root of the density ratio, appears to be an effective indicator of the deformation features.

A novel multi-channel porous structure facilitating mass transport towards highly efficient alkaline water electrolysis

An advantageous porous architecture of electrodes is pivotal in significantly enhancing alkaline water electrolysis(AWE)efficiency by optimizing the mass transport mechanisms.This effect becomes even more pronounced when aiming to achieve elevated current densities.Herein,we employed a rapid and scalable laser texturing process to craft novel multi-channel porous electrodes.Particularly,the obtained electrodes exhibit the lowest Tafel slope of 79 mV dec^(-1)(HER)and 49 mV dec^(-1)(OER).As anticipated,the alkaline electrolyzer(AEL)cell incorporating multi-channel porous electrodes(NP-LT30)exhibited a remarkable improvement in cell efficiency,with voltage drops(from 2.28 to 1.97 V)exceeding 300 mV under 1 A cm^(-1),compared to conventional perforated Ni plate electrodes.This enhancement mainly stemmed from the employed multi-channel porous structure,facilitating mass transport and bubble dynamics through an innovative convection mode,surpassing the traditional convection mode.Furthermore,the NP-LT30-based AEL cell demonstrated exceptional durability for 300 h under 1.0 A cm^(-2).This study underscores the capability of the novel multi-channel porous electrodes to expedite mass transport in practical AWE applications.