Adsorption of dimethyl trisulfide from aqueous solution on a low-cost adsorbent:thermally activated pinecone

Thermally activated pinecone(TAP) was used for the adsorption of dimethyl trisulfide(DMTS)from aqueous solutions,which was proved to be the main odorous in algae-caused black bloom.The effects of adsorbent dosage,adsorbate concentration and contact time on DMTS biosorption were studied.The TAP produced at 600℃ exhibited a relatively high surface area(519.69 m^2/g) and excellent adsorption capacity.The results show that the adsorption of DMTS was initially fast and that the equilibrium time was6 h.Higher initial DMTS concentrations led to lower removal percentages but higher adsorption capacity.The removal percentage of DMTS increased and the adsorption capacity of TAP decreased with an increase in adsorbent dosage.The adsorption process conforms well to a pseudo-second-order kinetics model.The adsorption of DMTS is more appropriately described by the Freundlich isotherm(R^2=0.996 1) than by the Langmuir isotherm(R^2=0.916 9).The results demonstrate that TAP could be an attractive low-cost adsorbent for removing DMTS from water.

Valorization of Mango Peels as Low-Cost Biosorbent in Methylene Blue Adsorption:Kinetic and Equilibrium Study

Mango peels,which constitute a significant proportion of urban waste,have been modified with phosphoric acid for use as a biosorbent in the removal of methylene blue from wastewater.The characterization of the obtained biosorbent showed that cellulose is the primary constituent followed by lignin and hemicellulose.The high water content and the low value of ash content indicate that the studied biosorbent is a porous material containing a low proportion of inorganic,inert,amorphous and unusable part for biosorbent production.The zero charge point(pHpzc)assessment showed that the overall surface charge of the biosorbent is negative and therefore plays a key role in the adsorption process.The adsorption of methylene blue by mango peels biosorbent is a two-step process:a rapid first step in which over 90%methylene blue is removed in less than 10 min followed by a slowdown of the adsorption rate when approaching the adsorption equilibrium.Among pseudo-first,pseudo-second order and intraparticle diffusion kinetics models studies,pseudo-second order was the best applicable to describe methylene blue adsorption,suggesting a two-step mechanism:the transfer of methylene blue molecules from the solution to the mango peels biosorbent surface,followed by the interaction between adsorbates and surface.The equilibrium adsorption data were analyzed by Langmuir,Freundlich and Temkin isotherms models.Among them,Langmuir was the best model to describe adsorption,indicating the existence of homogeneous distribution of adsorption sites on mango peels biosorbent surface and a mono-layer adsorption of methylene blue molecules.The low value of Temkin’s constant B relative to the interaction energy between methylene blue molecules and the surface of the biosorbent shows that the adsorption involved is a physisorption process.

Assessment of the performance of the TOPGNSS and ANN-MB antennas for ionospheric measurements using low-cost u-blox GNSS receivers

Low-cost GNSS receivers have recently been gaining reliability as good candidates for ionospheric studies. In line with these gains are genuine concerns about improving the performance of these receivers. In this work, we present a comprehensive investigation of the performances of two antennas(the u-blox ANN-MB and the TOPGNSS TOP-106) used on a low-cost GNSS receiver known as the u-blox ZED-F9P. The two antennas were installed on two identical and co-located u-blox receivers. Data used from both receivers cover the period from January to June 2022. Results from the study indicate that the signal strengths are dominantly greater for the receiver with the TOPGNSS antenna than for the receiver with the ANN-MB antenna, implying that the TOPGNSS antenna is better than the ANN-MB antenna in terms of providing greater signal strengths. Summarily, the TOPGNSS antenna also performed better in minimizing the occurrence of cycle slips on phase TEC measurements. There are no conspicuous differences between the variances(computed as 5-min standard deviations) of phase TEC measurements for the two antennas, except for a period around May-June when the TOPGNSS gave a better performance in terms of minimizing the variances in phase TEC. Remarkably, the ANN-MB antenna gave a better performance than the TOPGNSS antenna in terms of minimizing the variances in pseudorange TEC for some satellite observations. For precise horizontal(North and East) positioning, the receiver with the TOPGNSS antenna gave better results, while the receiver with the ANN-MB antenna gave better vertical(Up) positioning. The errors for the receivers of both antennas are typically within about 5 m(the monthly mean was usually smaller than 1 m) in the horizontal direction and within about 10 m(the monthly mean was usually smaller than 4 m) in the vertical direction.

UAV-supported intelligent truth discovery to achieve low-cost communications in mobile crowd sensing

Unmanned and aerial systems as interactors among different system components for communications,have opened up great opportunities for truth data discovery in Mobile Crowd Sensing(MCS)which has not been properly solved in the literature.In this paper,an Unmanned Aerial Vehicles-supported Intelligent Truth Discovery(UAV-ITD)scheme is proposed to obtain truth data at low-cost communications for MCS.The main innovations of the UAV-ITD scheme are as follows:(1)UAV-ITD scheme takes the first step in employing UAV joint Deep Matrix Factorization(DMF)to discover truth data based on the trust mechanism for an Information Elicitation Without Verification(IEWV)problem in MCS.(2)This paper introduces a truth data discovery scheme for the first time that only needs to collect a part of n data samples to infer the data of the entire network with high accuracy,which saves more communication costs than most previous data collection schemes,where they collect n or kn data samples.Finally,we conducted extensive experiments to evaluate the UAV-ITD scheme.The results show that compared with previous schemes,our scheme can reduce estimated truth error by 52.25%–96.09%,increase the accuracy of workers’trust evaluation by 0.68–61.82 times,and save recruitment costs by 24.08%–54.15%in truth data discovery.

Unscented Kalman filter for a low-cost GNSS/IMU-based mobile mapping application under demanding conditions

For the last two decades,low-cost Global Navigation Satellite System(GNSS)receivers have been used in various applications.These receivers are mini-size,less expensive than geodetic-grade receivers,and in high demand.Irrespective of these outstanding features,low-cost GNSS receivers are potentially poorer hardwares with internal signal processing,resulting in lower quality.They typically come with low-cost GNSS antenna that has lower performance than their counterparts,particularly for multipath mitigation.Therefore,this research evaluated the low-cost GNSS device performance using a high-rate kinematic survey.For this purpose,these receivers were assembled with an Inertial Measurement Unit(IMU)sensor,which actively transmited data on acceleration and orientation rate during the observation.The position and navigation parameter data were obtained from the IMU readings,even without GNSS signals via the U-blox F9R GNSS/IMU device mounted on a vehicle.This research was conducted in an area with demanding conditions,such as an open sky area,an urban environment,and a shopping mall basement,to examine the device’s performance.The data were processed by two approaches:the Single Point Positioning-IMU(SPP/IMU)and the Differential GNSS-IMU(DGNSS/IMU).The Unscented Kalman Filter(UKF)was selected as a filtering algorithm due to its excellent performance in handling nonlinear system models.The result showed that integrating GNSS/IMU in SPP processing mode could increase the accuracy in eastward and northward components up to 68.28%and 66.64%.Integration of DGNSS/IMU increased the accuracy in eastward and northward components to 93.02%and 93.03%compared to the positioning of standalone GNSS.In addition,the positioning accuracy can be improved by reducing the IMU noise using low-pass and high-pass filters.This application could still not gain the expected position accuracy under signal outage conditions.

The Al_(2)O_(3)and Mn/Al_(2)O_(3)sorbents highly utilized in destructive sorption of NF_(3)

NF_(3)is commonly used as an etching and cleaning gas in semiconductor industry,however it is a strongly greenhouse gas.Therefore,the destruction of disposal NF_(3)is an urgent task to migrate the greenhouse effect.Among the technologies for NF_(3)abatement,the destructive sorption of NF_(3)over metal oxides sorbents is an effective way.Thus,the search for a highly reactive and utilized sorbent for NF_(3)destruction is in great demand.In this work,AlOOH supported on carbon-sphere(AlOOH/CS)as precursors were synthesized hydrothermally and heat-treated to prepare the Al_(2)O_(3)sorbents.The influence of AlOOH/CS hydrothermal temperatures on the reactivity of derived Al_(2)O_(3)sorbents for NF_(3)destruction was investigated,and it is shown that the Al2O3 from AlOOH/CS hydro-thermalized at 120℃is superior to others.Subsequently,the optimized Al_(2)O_(3)was covered by Mn(OH)x to prepare Mn/Al_(2)O_(3)sorbents via changing hydrothermal temperatures and Mn loadings.The results show that the Mn/Al_(2)O_(3)sorbents are more utilized than bare Al_(2)O_(3)in NF_(3)destructive sorption due to the promotional effect of Mn_(2)O_(3)as surface layer on the fluorination of Al_(2)O_(3)as substrate,especially the optimal 5%Mn/Al2O3(160℃)exhibits a utilization percentage as high as 90.4%,and remarkably exceeds all the sorbents reported so far.These findings are beneficial to develop more efficient sorbents for the destruction of NF_(3).

Performance Evaluation of Low-Cost Dual-Frequency GNSS Receivers for Precise Positioning in Senegal: Issues and Challenges

The development of this technology has favored the advances noted in recent years in the field of precise positioning. It has also paved the way for a wide range of research into the evaluation of their performance and reliability, their potential use in different fields, the improvement of performance and combined systems, etc. Single-frequency GNSS receivers, which for a long time remained the only category of low-cost GNSS receivers, often limited by their level of accuracy (metric) mainly due to their single-frequency nature, have been joined in the last decade by dual-frequency GNSS receivers developed by certain manufacturers of positioning equipment. These receivers now offer possible alternatives to the relatively expensive conventional (topographic quality) or geodetic receivers and. In this study, the performance of these low-cost dual-frequency receivers was evaluated in static and real-time kinematic GNSS positioning modes. Static positioning was carried out on three points with sessions of 2 h and 4 h over three days with antenna swapping (CHC i50, Leica GS14 and Emlid Reach RS2+). Real-time observations were carried out on eleven (11) points in open, poorly open and not at all open environments, in order to assess not only performance but also receiver sensitivity in environments with a high risk of multipath. The results obtained showed an average agreement of 2 cm in planimetry between the low-cost Emlid RS2+ receiver and the Leica GS14 and CHC i50 receivers. The differences in altimetry are nevertheless greater (sometimes up to decimetres for certain points). Real-time positioning results provided an average convergence of around 1 cm on the E, N and H components with the results from the low-cost Emlid Reach RS2+ and Ublox ZED-F9P receivers and the CHC i50 receiver. Analysis of the results obtained has enabled us to highlight the various issues and challenges associated with this new generation of GNSS receivers, with a view to enhancing their appropriation and optimal integration in the professional and research worlds.

Synthesis of highly reactive sorbent from industrial wastes and its CO_2 capture capacity

A kind of industrial solid waste, i.e., carbide slag, was used as CaO precursor to synthesize CO2 sorbent. The highly reactive synthetic sorbent was prepared from carbide slag, aluminum nitrate hydrate and glycerol water solution by the combustion synthesis method. The results show that the synthetic sorbent exhibits a much higher CO2 capture capacity compared with carbide slag. The CO2 capture capacity and the carbonation conversion of the synthetic sorbent are 0. 38 g/g and 0. 70 after 50 cycles, which are 1.8 and 2. 1 times those of carbide slag. The average carbonation conversion and the CO2 capture efficiency of the synthetic sorbent are higher than those of carbide slag with the same sorbent flow ratios. The required sorbent flow ratios are lower for synthetic sorbent to achieve the same CO2 capture efficiency compared with carbide slag. With the same sorbent flow ratio and CO2 capture efficiency, the energy requirement in calciner for the synthetic sorbent is less than that for carbide slag.

Impact of impregnation pressure on desulfurization performance of Zn-based sorbents supported on semi-coke

High-pressure impregnation, a new preparation method for sorbents to remove H2S from hot coal gas, is introduced in this paper. Semi-coke （SC） and ZnO is selected as the support and active component of sorbent, respectively. The sorbent preparation process includes high-pressure impregnation, filtration, ovendry and calcination. The aim of this research is to primarily study the effects of the impregnation pressure on physical properties and desulfurization ability of the sorbent. The desulfurization experiment was carried out in a fixed-bed reactor at 500 ~C and a simulated coal gas used in this work was composed of CO （33 vol%）, H2 （39 vol%）, H2S （300 ppm in volume）, and N2 （balance）. Experimental results show that the pore structure of the SC support can be improved effectively and ZnO active component can be uniformly dispersed on the support, with the small particle size of 10-500 nm. Sorbents prepared using high-pressure impregnation have better desulfurization capacity and their active components have higher utilization rate. P20-ZnSC sorbent, obtained by high-pressure impregnation at 20 atm, has the best desulfurization ability with a sulfur capacity of 7.54 g S/100g sorbent and a breakthrough time of 44 h. Its desulfurization precision and efficiency of removing H2S from the middle temperature gases can reach 〈 1 ppm and 〉99.7%, respectively, before sorbent breakthrough.

Recent progress of amine modified sorbents for capturing CO2 from flue gas

Under the Paris agreement, China has committed to reducing CO_2 emissions by 60%–65% per unit of GDP by 2030.Since CO_2 emissions from coal-fired power plants currently account for over 30% of the total carbon emissions in China, it will be necessary to mitigate at least some of these emissions to achieve this goal. Studies by the International Energy Agency(IEA) indicate CCS technology has the potential to contribute 14% of global emission reductions, followed by 40% of higher energy efficiency and 35% of renewable energy, which is considered as the most promising technology to significantly reduce carbon emissions for current coal-fired power plants.Moreover, the announcement of a Chinese national carbon trading market in late 2017 signals an opportunity for the commercial deployment of CO_2 capture technologies.Currently, the only commercially demonstrated technology for post-combustion CO_2 capture technology from power plants is solvent-based absorption. While commercially viable, the costs of deploying this technology are high. This has motivated efforts to develop more affordable alternatives, including advanced solvents, membranes,and sorbent capture systems. Of these approaches, advanced solvents have received the most attention in terms of research and demonstration. In contrast, sorbent capture technology has less attention, despite its potential for much lower energy consumption due to the absence of water in the sorbent. This paper reviews recent progress in the development of sorbent materials modified by amine functionalities with an emphasis on material characterization methods and the effects of operating conditions on performance. The main problems and challenges that need to be overcome to improve the competitiveness of sorbent-based capture technologies are discussed.

Effects of Sorbents on the Partitioning and Speciation of Cu During Municipal Solid Waste Incineration

Oxides of silicon, aluminium and calcium are normally dominant minerals during municipal solid waste(MSW)combustion. In flue gas, Si O2, Al2O3 and Ca O all act as sorbents capturing heavy metals(and semi-volatile organics). To further understand the effect of sorbents during MSW combustion, the effects of Si O2, Al2O3 and Ca O on Cu partitioning were experimentally investigated by the combustion of synthetic MSW in a tubular furnace and their effects on Cu speciation were studied by thermodynamic equilibrium calculations using Chem Kin software. The experiments show that Ca O has the highest Cu sorption efficiency at 900 °C, followed by Al2O3 and Si O2. Thermodynamic equilibrium calculations show that for Cu the addition of Si O2 and Al2O3reduces the amount of liquid Cu Cl, which is more volatile. However, the addition of Ca O has little influence on chemical sorption of Cu, indicating that the sorption of Ca O is resulted from physical sorption.

Preparation and utilization of wheat straw anionic sorbent for the removal of nitrate from aqueous solution

In order to reduce the impact of eutrophication caused by agricultural residues （i.e., excess nitrate） in aqueous solution, economic and effective anionic sorbents are required. In this article, we prepared anionic sorbent using wheat straw. Its structural characteristics and adsorption properties for nitrate removal from aqueous solution were investigated. The results indicate that the yield of the prepared anionic sorbent, the total exchange capacity, and the maximum adsorption capacity were 350%, 2.57 mEq/g, and 2.08 mmol/g, respectively. The Freundlich isotherm mode is more suitable than the Langmuir mode and the adsorption process accords with the first order reaction kinetic rate equation. When multiple anions （SO4^2-, H2PO4^-, NO3^-, and NO2^-） were present, the isotherm mode of prepared anionic sorbent for nitrate was consistent with Freundlich mode; however, the capacity of nitrate adsorption was reduced by 50%. In alkaline solutions, about 90% of adsorbed nitrate ions could be desorbed from prepared anionic sorbent. The results of this study confirmed that the wheat straw anionic sorbent can be used as an excellent nitrate sorbent that removes nitrate from aqueous solutions.

Desulfurization kinetics of ZnO sorbent loaded on semi-coke support for hot coal gas

Zn-based sorbent （Z20SC） prepared through semi-coke support in 20 wt% zinc nitrate solution by high-pressure impregnation presents an excellent desulfurization capacity in hot coal gas,in which H2 S can not be nearly detected in the outlet gas before 20 h breakthrough time.The effects of the main operational conditions and the particle size of Z20SC sorbent on its desulfurization performances sorbent were investigated in a fixed-bed reactor and the desulfurization kinetics of Z20SC sorbent removing H2 S from hot coal gas was calculated based on experimental data.Results showed that the conversion of Z20SC sorbent desulfurization reaction increased with the decrease of the particle size of the sorbent and the increases of gas volumetric flow rate,reaction temperature and H 2 S content in inlet gas.Z20SC sorbent obtained from hydrothermal synthesis by high-pressure impregnation possessed much larger surface area and pore volume than semi-coke support,and they were significantly reduced after the desulfurization reaction.The equivalent grain model was reasonably used to analyze experimental data,in which k s=4.382×10-3 exp（-8.270×103/RgT） and Dep=1.262×10-4exp（1.522×104/RgT）.It suggests that the desulfurization reaction of the Z20SC sorbent is mainly controlled by the chemical reaction in the initial stage and later by the diffusion through the reacted sorbent layer.

Bench-Scale Testing of Zinc Ferrite Sorbent for Hot Gas Clean-up

Advanced integrated gasification combined cycle （IGCC） power generation systems require the development of high-temperature, regenerable desulfurization sorbents, which are capable of removing hydrogen sulfide from coal gasifier gas to very low levels. In this paper, zinc ferrites prepared by co-precipitation were identified as a novel coal gas desulfurization sorbent at high temperature. Preparation of zinc ferrite and effects of binders on pore volume, strength and desulfurization efficiency of zinc ferrite desulfurizer were studied. Moreover, the behavior of zinc ferrite sorbent during desulfurization and regeneration under the temperature range of 350-400 ℃ are investigated. Effects of binders on the pore volume, mechanical strength and desulfurization efficiency of zinc ferrite sorbents indicated that the addition of kaolinite to zinc ferrite desulfurizer seems to be superior to other binders under the experimental conditions.

Effect of impregnation methods on sorbents made from lignite for desulfurization at middle temperature

With lignite after vacuum drying as the raw material,a series of Zn-based sorbents were prepared by static impregnation,ultrasonic-assisted impregnation,bubbling-assisted impregnation and high-pressure impregnation.The physical properties and the desulfurization performances of Zn-based sorbents were studied systematically by XRD,BET,AAS characterization techniques and the fixed-bed desulfurization evaluation apparatus.The sorbents obtained by high-pressure impregnation method have a larger specific surface area,pore volume and pore diameter comparing with other methods,which is conducive to the sulfidation reaction of hydrogen sulfide gas in the sorbent.The effects of pressure during the high-pressure impregnation and concentration of Zn(NO3)2 precursor solution on the sorbents properties and desulfurization behavior were investigated.The higher the impregnation pressure and the concentration of impregnation solution are,the greater the amount of the active components are uploaded.However,overhigh impregnation pressure can cause collapse and blocking of the carrier pore.The optimal operating condition of high-pressure impregnation method for preparing the sorbents was the impregnation pressure of 20 atm and the solution concentration of 41%.Under that condition,the sorbent had the best desulfurization ability with a sulfur capacity of 13.94 gS/100 gsorbent and a breakthrough time of 54 h.Its desulfurization precision and efficiency of removing H2S before sorbent breakthrough from the middle temperature gases of 400℃ can reach【5 ppm and】99%,respectively.Sorbents could be regenerated under the condition of 1 vol%O2,20 vol% H2O,0.5 vol% NH3,and N2balance gas.The regenerated sorbent could be used for repeated absorption of H2S with a slight decrease in desulfurization effect.

Study on Zn_2SiO_4 Formation Kinetics and Activity Stability of Desulfurization Sorbent

A new industrial S Zorb sorbent(Ni/Zn O-P) was prepared by using the spray drying technique. The other two traditional sorbents(Ni/Zn O-M and Ni/Zn O-H) were prepared in exactly the same way except the use of different silica-alumina binder matrices. The XRD, Rietveld quantitative phase analysis, BET, and laser particle size analysis were employed to characterize their physico-chemical properties. The deactivation mechanism and desulfurization kinetics of sorbent was investigated on a water vapor aging treatment device. It was shown that both the water vapor pressure and reaction temperature significantly could influence the formation rate of inactive Zn2 Si O4, which could decrease the sulfur storage capacity of sorbents. The Zn2 Si O4 content profiles could be fitted into the zero order equation, from which the apparent rate constant k and the activation energy E a were calculated. The matrix P greatly raised the E a of Zn2 Si O4 formation due to the less bridged hydroxyl silanol groups on its surface, which accounted for the high stability of Ni/Zn O-P. The desulfurization performance of the fresh and aged sorbents showed that the overall average sulfur conversion of Ni/Zn O-P(aged) was 92%, which was close to that of fresh sorbents(95%), and was higher than that of Ni/Zn O-M(aged)(86%) and Ni/Zn O-H(aged)(90%). Based on these findings, the application of Ni/Zn O-P can greatly improve the long-term running stability of the industrial unit.

Effects of ultrasound on the desulfurization performance of hot coal gas over Zn-Mn-Cu supported on semi-coke sorbent prepared by high-pressure impregnation method

Zn-Mn-Cu/SC（U） sorbent was hydrothermally synthesized by ultrasound-assisted high-pressure impregnation method with semi-coke（SC）as support and the mixed solution of zinc nitrate,manganese nitrate and copper nitrate as active component precursors.The desulfurization performances of hot coal gas on the prepared sorbent at a mid-temperature of 500°C were tested in fixed-bed reactor.Morphology and pore structure of the prepared sorbent were also characterized by TEM,N2adsorption/desorption isotherms and XRD.For comparison,the sorbent of Zn-Mn-Cu/SC prepared by conventional high-pressure impregnation was also evaluated and characterized in order to study the effects of ultrasound treatment.Zn-Mn-Cu/SC（U） sorbent prepared by high-pressure impregnation under ultrasound-assisted condition showed a better desulfurization performance than Zn-Mn-Cu/SC.It could remove H2 S from 1000×10-6m3/m3 to 0.1×10-6m3/m3 at 500°C and maintained for 12.5 h with the sulfur capacity of 7.74%,in which both the breakthrough time and sulfur capacity were about 32% and 51% higher than those of Zn-Mn-Cu/SC sorbent.The introduction of ultrasound during high-pressure impregnation process greatly improved the morphology and pore structure of the sorbent.The ultrasonic treatment made particle size of active components smaller and made them more evenly disperse on semi-coke support,which provided more opportunities to contact with H2S in coal-based gases.However,there were no any difference in compositions and existing forms of active components on the Zn-Mn-Cu/SC and Zn-Mn-Cu/SC（U） sorbents.

CO2 capture over molecular basket sorbents:Effects of SiO2 supports and PEG additive

The objective of this work is to study the influences of silica supports and PEG additive on the sorption performance of molecular basket sorbent（MBS） for COcapture consisting of polyethylenimine and one of the following supports: SBA-15（2-D structure）, TUD-1（3-D sponge-like structure） and fumed silica HS-5（3-D disordered structure）. Effects of the supports regarding pore structures and pore properties, the PEI loading amount as well as the sorption temperature were examined. Furthermore, polyethylene glycol（PEG） was introduced as an additive into the sorbents and its effect was investigated at different PEI loadings and sorption temperatures. The results suggest that the pore properties of MBS（after PEI loading） play a more important role in the COsorption capacity, rather than those of the supports alone.MBS with 3D pore structure exhibits higher COsorption capacity and amine efficiency than those with 2D-structured support. Among the sorbents studied, fumed silica（HS-5） based MBS showed the highest COsorption capacity in the temperature range of 30-95 °C, probably due to its unique interstitial pores formed by the aggregation of polymer-loaded SiOparticles. It was found that the temperature dependence is directly related to the PEI surface coverage layers. The more PEI surface coverage layers, the higher diffusion barrier for COand the stronger temperature dependence of COcapacity. 3D MBS exceeds 2D MBS at the same PEI coverage layers due to lower diffusion barrier. Adding PEG can significantly enhance the COsorption capacity and improve amine efficiency of all MBS, most likely by alleviating the diffusion barrier within PEI bulk layers through the inter-molecular interaction between PEI and PEG.

A fibrous hypercrosslinked sorbent prepared on PP-ST-DVB matrix via post-crosslinking reaction

A fibrous sorbent possessing abundant micropore structure was firstly prepared via post-crosslinking reaction on the PP-ST-DVB original fiber. Its micromorphology and sorptive properties were investigated, and the results demonstrated that the novel fibrous hypererosslinked sorbent has narrow pore-size distribution, small average porous radius （1.90 nm）, high specific surface area （362.31 m^2/g）, and fine sorptive properties for small organic molecules.

Sb(Ⅴ) removal from copper electrorefining electrolyte: Comparative study by different sorbents

Removal of Sb（V） from copper electrolyte by different sorbents such as activated carbon, bentonite, kaolin, resin, zeolite and white sand was investigated. Adsorption capacity of Sb（V） removal from copper electrolyte was as follows： white sand 〈 anionic resin 〈 zeolite 〈 kaolin 〈 activated carbon 〈 bentonite. Bentonite was characterized using FTIR, XRF, XRD, SEM and BET methods. The results show specific surface area of 95 m2/g and particles size of 175 nm for bentonite. The optimum conditions for the maximum removal of Sb are contact time 10 min, 4 g bentonite and temperature of 40 ° C. The adsorption of Sb（V） on bentonite is followed by pseudo-second-order kinetic （R2=0.996 and k=9×10？5 g/（mg· min））. Thermodynamic results reveal that the adsorption of Sb（V） onto bentonite from copper electrolyte is endothermic and spontaneous process （ΔGΘ=？4806 kJ/（mol· K）. The adsorption data fit both the Freundlich and Langmuir isotherm models. Bentonite has the maximum adsorption capacity of 10000 mg/g for adsorption of Sb（V） in copper electrolyte. The adsorption of Zn, Co, Cu and Bi that present in the copper electrolyte is very low and insignificant.