Analysis of the Effect of Radiation Defects by Low-energy Protons on Electrophysical Properties of Silicon N^(+)-P-P^(+) Structure

Nowadays,radiation engineering is a promising direction in the creation of semiconductor devices.The proton irradiation is used to controllably change the optical,electrical,recombination,mechanical and structural properties of the semiconductors.Low-energy protons make it possible to purposefully change material properties near the surface where the n^(+)-p junction is located.In this paper,the impact of low-energy protons on the electro physical parameters of n+-p-p+silicon photoelectric converters(SPC)is analyzed.The current-voltage characteristics and switching time of these SPCs are measured.The switching time is determined using rectangular bipolar voltage pulses with an amplitude of 10 mV,a frequency of 200 kHz,or a frequency of 1 MHz.A theoretical and experimental analysis of the obtained results is performed.The comparison of experimental data with the results of calculations shows that protons with an energy of 180 keV and a dose of 10×15 cm^(-2) create two regions in the space charge region of the n^(+)-p junction with different switching times of 4.2×10^(-7) s and 5.5×10^(-8) s.SPC frequency characteristics have been improved by reducing the effective lifetime by 5-10 times.This effect can be used to create high-speed photodiodes with an operating modulation frequency of 18 MHz.

Radiation-hardened property of single-walled carbon nanotube film-based field-effect transistors under low-energy proton irradiation

Strong C-C bonds,nanoscale cross-section and low atomic number make single-walled carbon nanotubes(SWCNTs)a potential candidate material for integrated circuits(ICs)applied in outer space.However,very little work combines the simulation calculations with the electrical measurements of SWCNT field-effect transistors(FETs),which limits further understanding on the mechanisms of radiation effects.Here,SWCNT film-based FETs were fabricated to explore the total ionizing dose(TID)and displacement damage effect on the electrical performance under low-energy proton irradiation with different fluences up to 1×1015 p/cm2.Large negative shift of the threshold voltage and obvious decrease of the on-state current verified the TID effect caused in the oxide layer.The stability of the subthreshold swing and the off-state current reveals that the displacement damage caused in the CNT layer is not serious,which proves that the CNT film is radiation-hardened.Specially,according to the simulation,we found the displacement damage caused by protons is different in the source/drain contact area and channel area,leading to varying degrees of change for the contact resistance and sheet resistance.Having analyzed the simulation results and electrical measurements,we explained the low-energy proton irradiation mechanism of the CNT FETs,which is essential for the construction of radiation-hardened CNT film-based ICs for aircrafts.

Effect of low-energy proton on the microstructure, martensitic transformation and mechanical properties of irradiated Ni-rich TiNi alloy thin films

Ni–48.5at%Ti thin films were irradiated in the austenite phase by different energy-level protons at a dose rate of 1.85×1012 p/(cm2·s),and the total dose was 2.0×1016 p/cm2.The microstructures of the thin films before and after irradiation were evaluated by transmission electron microscopy(TEM)and grazing-incidence X-ray diffraction(GIXRD),which showed that the volume fraction of Ti3Ni4 phase elevated with proton energy level.The influence of proton irradiation on the transformation behavior of the TiNi thin films was investigated by differential scanning calorimetry(DSC).Compared with the unirradiation film,the reverse transformation start temperatures(As)decreased by about 3°C after 120 keV proton-irradiation.The proton irradiation also had a significant effect on the mechanical properties of the TiNi thin films.After 120 keV energy proton-irradiation,the fracture strength increased by 8.44%,and the critical stress increased by 21.1%.In addition,the nanoindenter measurement image showed that the hardness of the thin films increased with the increase of proton-irradiation energy.This may be due to the defects caused by irradiation,which strengthen the matrix.

Imaging principle and experiment results of an 11 MeV low-energy proton radiography system

Differing from radiography without lens system, the high-energy proton radiography(PRAD) uses Zumbro lens system to focus the penetrating protons. Since the Zumbro lens system is able to limit the range of multiple Coulomb scattering angles of the protons, the low-energy PRAD with Zumbro lens system is also feasible,although the attenuation of probing protons in the object is negligible. Low-energy PRAD is superior to the high-energy PRAD for diagnosing the objects of small thicknesses. To verify the imaging principle of Zumbro lens system, 11 MeV PRAD experiments were performed at the China Academy of Engineering Physics(CAEP)recently. The experiment results demonstrated that this 11 MeV PRAD was able to radiograph objects of area density less than 2.7 × 10-2 g/cm2 and the area density discrepancy less than 2.3% could be distinguished.

Correlation between hydration properties and electrochemical performances on Ln cation size effect in layered perovskite for protonic ceramic fuel cells

PrBa_(0.5)Sr_(0.5)Co_(1.5)Fe_(0.5)O_(5+δ)(PrBSCF) has attracted much research interest as a potential triple ionic and electronic conductor(TIEC) electrode for protonic ceramic fuel cells(PCFCs). The chemical formula for Pr BSCF is AA'B_(2)O_(5+δ), with Pr(A-site) and Ba/Sr(A'-site) alternately stacked along the c-axis. Due to these structural features, the bulk oxygen ion diffusivity is significantly enhanced through the disorder-free channels in the PrO layer;thus, the A site cations(lanthanide ions) play a pivotal role in determining the overall electrochemical properties of layered perovskites. Consequently, previous research has predominantly focused on the electrical properties and oxygen bulk/surface kinetics of Ln cation effects,whereas the hydration properties for PCFC systems remain unidentified. Here, we thoroughly examined the proton uptake behavior and thermodynamic parameters for the hydration reaction to conclusively determine the changes in the electrochemical performances depending on LnBa_(0.5)Sr_(0.5)Co_(1.5)Fe_(0.5)O_(5+δ)(LnBSCF,Ln=Pr, Nd, and Gd) cathodes. At 500 ℃, the quantitative proton concentration of PrBSCF was 2.04 mol% and progressively decreased as the Ln cation size decreased. Similarly, the Gibbs free energy indicated that less energy was required for the formation of protonic defects in the order of Pr BSCF < Nd BSCF < Gd BSCF. To elucidate the close relationship between hydration properties and electrochemical performances in LnBSCF cathodes, PCFC single cell measurements and analysis of the distribution of relaxation time were further investigated.

Conceptual design of a 714-MHz RFQ for compact proton injectors and development of a new tuning algorithm on its aluminium prototype

Radio frequency quadrupoles(RFQs),which are crucial components of proton injectors,significantly affect the performance of proton accelerator facilities.An RFQ with a high frequency of 714 MHz dedicated to compact proton injectors for medi-cal applications is designed in this study.The RFQ is designed to accelerate proton beams from 50 keV to 4 MeV within a short length of 2 m and can be matched closely with the downstream drift tube linac to capture more particles through a preliminary optimization.To develop an advanced RFQ,challenging techniques,including fabrication and tuning method,must be evaluated and verified using a prototype.An aluminium prototype is derived from the conceptual design of the RFQ and then redesigned to confirm the radio frequency performance,fabrication procedure,and feasibility of the tuning algorithm.Eventually,a new tuning algorithm based on the response matrix and least-squares method is developed,which yields favorable results based on the prototype,i.e.,the errors of the dipole and quadrupole components reduced to a low level after several tuning iterations.Benefiting from the conceptual design and techniques obtained from the prototype,the formal mechanical design of the 2-m RFQ is ready for the next manufacturing step.

Molecular-level proton acceptor boosts oxygen evolution catalysis to enable efficient industrial-scale water splitting

Industrial water splitting has long been suppressed by the sluggish kinetics of the oxygen evolution reaction(OER),which requires a catalyst to be efficient.Herein,we propose a molecular-level proton acceptor strategy to produce an efficient OER catalyst that can boost industrial-scale water splitting.Molecular-level phosphate(-PO_(4))group is introduced to modify the surface of PrBa_(0.5)Ca_(0.5)Co_(2)O_(5)+δ(PBCC).The achieved catalyst(PO_(4)-PBCC)exhibits significantly enhanced catalytic performance in alkaline media.Based on the X-ray absorption spectroscopy results and density functional theory(DFT)calculations,the PO_(4)on the surface,which is regarded as the Lewis base,is the key factor to overcome the kinetic limitation of the proton transfer process during the OER.The use of the catalyst in a membrane electrode assembly(MEA)is further evaluated for industrial-scale water splitting,and it only needs a low voltage of 1.66 V to achieve a large current density of 1 A cm^(-2).This work provides a new molecular-level strategy to develop highly efficient OER electrocatalysts for industrial applications.

Overlapping approach Proton Pump Inhibitors/Nux vomica-Heel as new intervention for gastro-esophageal reflux management:Delphi consensus study

BACKGROUND Gastro-esophageal reflux disease(GERD)may affect the upper digestive tract;up to 20%of population in Western nations are affected by GERD.Antacids,histamine H2-receptor antagonists,and Proton Pump Inhibitors(PPIs)are considered the referring medications for GERD.Nevertheless,PPIs must be managed carefully because their use,especially chronic,could be linked with some adverse effects.An effective and safe alternative pharmacological tool for GERD is needed.After the identification of potentially new medications to flank PPIs,it is mandatory to revise and improve good clinical practices even through a consensus process.AIM To optimize diagnosis and treatment guidelines for GERD through a consensus based on Delphi method.METHODS The availability of clinical studies describing the action of the multicomponent/multitarget medication Nux vomica-Heel,subject of the consensus,is the basic prerequisite for the consensus itself.A modified Delphi process was used to reach a consensus among a panel of Italian GERD specialists on the overlapping approach PPIs/Nux vomica-Heel as a new intervention model for the management of GERD.The Voting Consensus group was composed of 49 Italian Medical Doctors with different specializations:Gastroenterology,otolaryngology,geriatrics,and general medicine.A scientific committee analyzed the literature,determined areas that required investigation(in agreement with the multiple-choice questionnaire results),and identified two topics of interest:(1)GERD disease;and(2)GERD treatment.Statements for each of these topics were then formulated and validated.The Delphi process involved two rounds of questioning submitted to the panel experts using an online platform.RESULTS According to their routinary GERD practice and current clinical evidence,the panel members provided feedback to each questionnaire statement.The experts evaluated 15 statements and reached consensus on all 15.The statements regarding the GERD disease showed high levels of agreement,with consensus ranging from 70%to 92%.The statements regarding the GERD treatment also showed very high levels of agreement,with consensus ranging from 90%to 100%.This Delphi process was able to reach consensus among physicians in relevant aspects of GERD management,such as the adoption of a new approach to treat patients with GERD based on the overlapping between PPIs and Nux vomica-Heel.The consensus was unanimous among the physicians with different specializations,underlying the uniqueness of the agreement reached to identify in the overlapping approach between PPIs and Nux vomica-Heel a new intervention model for GERD management.The results support that an effective approach to deprescribe PPIs through a progressive decalage timetable(reducing PPIs administration to as-needed use),should be considered.CONCLUSION Nux vomica-Heel appears to be a valid opportunity for GERD treatment to favor the deprescription of PPIs and to maintain low disease activity together with the symptomatology remission.

Rational Design of Ruddlesden-Popper Perovskite Ferrites as Air Electrode for Highly Active and Durable Reversible Protonic Ceramic Cells

Reversible protonic ceramic cells(RePCCs)hold promise for efficient energy storage,but their practicality is hindered by a lack of high-performance air electrode materials.Ruddlesden-Popper perovskite Sr_(3)Fe_(2)O_(7−δ)(SF)exhibits superior proton uptake and rapid ionic conduction,boosting activity.However,excessive proton uptake during RePCC operation degrades SF’s crystal structure,impacting durability.This study introduces a novel A/B-sites co-substitution strategy for modifying air electrodes,incorporating Sr-deficiency and Nb-substitution to create Sr_(2.8)Fe_(1.8)Nb_(0.2)O_(7−δ)(D-SFN).Nb stabilizes SF’s crystal,curbing excessive phase formation,and Sr-deficiency boosts oxygen vacancy concentration,optimizing oxygen transport.The D-SFN electrode demonstrates outstanding activity and durability,achieving a peak power density of 596 mW cm^(−2)in fuel cell mode and a current density of−1.19 A cm^(−2)in electrolysis mode at 1.3 V,650℃,with excellent cycling durability.This approach holds the potential for advancing robust and efficient air electrodes in RePCCs for renewable energy storage.

Effects of baffle position in serpentine flow channel on the performance of proton exchange membrane fuel cells

This study used a three-dimensional numerical model of a proton exchange membrane fuel cell with five types of channels:a smooth channel(Case 1);eight rectangular baffles were arranged in the upstream(Case 2),midstream(Case 3),downstream(Case 4),and the entire cathode flow channel(Case 5)to study the effects of baffle position on mass transport,power density,net power,etc.Moreover,the effects of back pressure and humidity on the voltage were investigated.Results showed that compared to smooth channels,the oxygen and water transport facilitation at the diffusion layer-channel interface were added 11.53%-20.60%and 7.81%-9.80%at 1.68 A·cm^(-2)by adding baffles.The closer the baffles were to upstream,the higher the total oxygen flux,but the lower the flux uniformity the worse the water removal.The oxygen flux of upstream baffles was 8.14%higher than that of downstream baffles,but oxygen flux uniformity decreased by 18.96%at 1.68 A·cm^(-2).The order of water removal and voltage improvement was Case 4>Case 5>Case 3>Case 2>Case 1.Net power of Case 4 was 9.87%higher than that of the smooth channel.To the Case 4,when the cell worked under low back pressure or high humidity,the voltage increments were higher.The potential increment for the back pressure of 0 atm was 0.9%higher than that of 2 atm(1 atm=101.325 kPa).The potential increment for the humidity of 100%was 7.89%higher than that of 50%.

Moisture‑Electric–Moisture‑Sensitive Heterostructure Triggered Proton Hopping for Quality‑Enhancing Moist‑Electric Generator

Moisture-enabled electricity(ME)is a method of converting the potential energy of water in the external environment into electrical energy through the interaction of functional materials with water molecules and can be directly applied to energy harvesting and signal expression.However,ME can be unreliable in numerous applications due to its sluggish response to moisture,thus sacrificing the value of fast energy harvesting and highly accurate information representation.Here,by constructing a moisture-electric-moisture-sensitive(ME-MS)heterostructure,we develop an efficient ME generator with ultra-fast electric response to moisture achieved by triggering Grotthuss protons hopping in the sensitized ZnO,which modulates the heterostructure built-in interfacial potential,enables quick response(0.435 s),an unprecedented ultra-fast response rate of 972.4 mV s^(−1),and a durable electrical signal output for 8 h without any attenuation.Our research provides an efficient way to generate electricity and important insight for a deeper understanding of the mechanisms of moisture-generated carrier migration in ME generator,which has a more comprehensive working scene and can serve as a typical model for human health monitoring and smart medical electronics design.

Effects of proton pump inhibitors on inflammatory bowel disease:An updated review

Inflammatory bowel disease(IBD)is believed to be caused by various factors,including abnormalities in disease susceptibility genes,environmental factors,immune factors,and intestinal bacteria.Proton pump inhibitors(PPIs)are the primary drugs used to treat acid-related diseases.They are also commonly prescribed to patients with IBD.Recent studies have suggested a potential association between the use of certain medications,such as PPIs,and the occurrence and progression of IBD.In this review,we summarize the potential impact of PPIs on IBD and analyze the underlying mechanisms.Our findings may provide insights for conducting further investigations into the effects of PPIs on IBD and serve as an important reminder for physicians to exercise caution when prescribing PPIs to patients with IBD.

Correlation between cerebral neurotransmitters levels by proton magnetic resonance spectroscopy and HbA1c in patients with type 2 diabetes

BACKGROUND Cognitive dysfunction is the main manifestation of central neuropathy.Although cognitive impairments tend to be overlooked in patients with diabetes mellitus(DM),there is a growing body of evidence linking DM to cognitive dysfunction.Hyperglycemia is closely related to neurological abnormalities,while often disregarded in clinical practice.Changes in cerebral neurotransmitter levels are associated with a variety of neurological abnormalities and may be closely related to blood glucose control in patients with type 2 DM(T2DM).AIM To evaluate the concentrations of cerebral neurotransmitters in T2DM patients exhibiting different hemoglobin A1c(HbA1c)levels.METHODS A total of 130 T2DM patients were enrolled at the Department of Endocrinology of Shanghai East Hospital.The participants were divided into four groups according to their HbA1c levels using the interquartile method,namely Q1(<7.875%),Q2(7.875%-9.050%),Q3(9.050%-11.200%)and Q4(≥11.200%).Clinical data were collected and measured,including age,height,weight,neck/waist/hip circumferences,blood pressure,comorbidities,duration of DM,and biochemical indicators.Meanwhile,neurotransmitters in the left hippocampus and left brainstem area were detected by proton magnetic resonance spectroscopy.RESULTS The HbA1c level was significantly associated with urinary microalbumin(mALB),triglyceride,low-density lipoprotein cholesterol(LDL-C),homeostasis model assessment of insulin resistance(HOMA-IR),and beta cell function(HOMA-β),N-acetylaspartate/creatine(NAA/Cr),and NAA/choline(NAA/Cho).Spearman correlation analysis showed that mALB,LDL-C,HOMA-IR and NAA/Cr in the left brainstem area were positively correlated with the level of HbA1c(P<0.05),whereas HOMA-βwas negatively correlated with the HbA1c level(P<0.05).Ordered multiple logistic regression analysis showed that NAA/Cho[Odds ratio(OR):1.608,95%confidence interval(95%CI):1.004-2.578,P<0.05],LDL-C(OR:1.627,95%CI:1.119-2.370,P<0.05),and HOMA-IR(OR:1.107,95%CI:1.031-1.188,P<0.01)were independent predictors of poor glycemic control.CONCLUSION The cerebral neurotransmitter concentrations in the left brainstem area in patients with T2DM are closely related to glycemic control,which may be the basis for the changes in cognitive function in diabetic patients.

In-situ coating and surface partial protonation co-promoting performance of single-crystal nickel-rich cathode in all-solid-state batteries

The poor electrochemical performance of all-solid-state batteries(ASSBs),which is assemblied by Ni-rich cathode and poly(ethylene oxide)(PEO)-based electrolytes,can be attributed to unstable cathodic interface and poor crystal structure stability of Ni-rich cathode.Several coating strategies are previously employed to enhance the stability of the cathodic interface and crystal structure for Ni-rich cathode.However,these methods can hardly achieve simplicity and high efficiency simultaneously.In this work,polyacrylic acid(PAA)replaced traditional PVDF as a binder for cathode,which can achieve a uniform PAA-Li(LixPAA(0<x≤1))coating layer on the surface of single-crystal LiNi_(0.83)Co_(0.12)Mn_(0.05)O_(2)(SC-NCM83)due to H^(+)/Li^(+)exchange reaction during the initial charging-discharging process.The formation of PAA-Li coating layer on cathode can promote interfacial Li^(+)transport and enhance the stability of the cathodic interface.Furthermore,the partially-protonated surface of SC-NCM83 casued by H^(+)/Li^(+)exchange reaction can restrict Ni ions transport to enhance the crystal structure stability.The proposed SC-NCM83-PAA exhibits superior cycling performance with a retention of 92%compared with that(57.3%)of SC-NCM83-polyvinylidene difluoride(PVDF)after 200 cycles.This work provides a practical strategy to construct high-performance cathodes for ASSBs.

Sensitivity investigation of 100-MeV proton irradiation to SiGe HBT single event effect

The single event effect(SEE) sensitivity of silicon–germanium heterojunction bipolar transistor(Si Ge HBT) irradiated by 100-Me V proton is investigated. The simulation results indicate that the most sensitive position of the Si Ge HBT device is the emitter center, where the protons pass through the larger collector-substrate(CS) junction. Furthermore, in this work the experimental studies are also carried out by using 100-Me V proton. In order to consider the influence of temperature on SEE, both simulation and experiment are conducted at a temperature of 93 K. At a cryogenic temperature, the carrier mobility increases, which leads to higher transient current peaks, but the duration of the current decreases significantly.Notably, at the same proton flux, there is only one single event transient(SET) that occurs at 93 K. Thus, the radiation hard ability of the device increases at cryogenic temperatures. The simulation results are found to be qualitatively consistent with the experimental results of 100-Me V protons. To further evaluate the tolerance of the device, the influence of proton on Si Ge HBT after gamma-ray(^(60)Coγ) irradiation is investigated. As a result, as the cumulative dose increases, the introduction of traps results in a significant reduction in both the peak value and duration of the transient currents.

Study on the optimal incident proton energy of ^(7)Li(p,n)^(7)Be neutron source for boron neutron capture therapy

Boron neutron capture therapy(BNCT)is recognized as a precise binary targeted radiotherapy technique that effectively eliminates tumors through the^(10)B(n,α)^(7)Li nuclear reaction.Among various neutron sources,accelerator-based sources have emerged as particularly promising for BNCT applications.The^(7)Li(p,n)^(7)Be reaction is highly regarded as a potential neutron source for BNCT,owing to its low threshold energy for the reaction,significant neutron yield,appropriate average neutron energy,and additional benefits.This study utilized Monte Carlo simulations to model the physical interactions within a lithium target subjected to proton bombardment,including neutron moderation by an MgF_(2)moderator and subsequent BNCT dose analysis using a Snyder head phantom.The study focused on calculating the yields of epithermal neutrons for various incident proton energies,finding an optimal energy at 2.7 MeV.Furthermore,the Snyder head phantom was employed in dose simulations to validate the effectiveness of this specific incident energy when utilizing a^(7)Li(p,n)^(7)Be neutron source for BNCT purposes.

Endoscopic full-thickness plication along with argon plasma coagulation for treatment of proton pump inhibitor dependent gastroesophageal reflux disease

BACKGROUND Most endoscopic anti-reflux interventions for gastroesophageal reflux disease(GERD)management are technically challenging to practice with inadequate data to support it utility.Therefore,this study was carried to evaluate the effectiveness and safety newer endoscopic full-thickness fundoplication(EFTP)device along with Argon Plasma Coagulation to treat individuals with GERD.AIM To evaluate the effectiveness and safety newer EFTP device along with Argon Plasma Coagulation to treat individuals with GERD.METHODS This study was a single-center comparative analysis conducted on patients treated at a Noble Institute of Gastroenterology,Ahmedabad,hospital between 2020 and 2022.The research aimed to retrospectively analyze patient data on GERD symptoms and proton pump inhibitor(PPI)dependence who underwent EFTP using the GERD-X system along with argon plasma coagulation(APC).The primary endpoint was the mean change in the total gastroesophageal reflux disease health-related quality of life(GERD-HRQL)score compared to the baseline measurement at the 3-month follow-up.Secondary endpoints encompassed enhancements in the overall GERD-HRQL score,improvements in GERD symptom scores at the 3 and changes in PPI usage at the 3 and 12-month time points.RESULTS In this study,patients most were in Hill Class II,and over half had ineffective esophageal motility.Following the EFTP procedure,there were significant improvements in heartburn and regurgitation scores,as well as GERDHRQL scores(P<0.001).PPI use significantly decreased,with 82.6%not needing PPIs or prokinetics at end of 1 year.No significant adverse events related to the procedures were observed in either group.CONCLUSION The EFTP along with APC procedure shows promise in addressing GERD symptoms and improving patients'quality of life,particularly for suitable candidates.Moreover,the application of a lone clip with APC yielded superior outcomes and exhibited greater cost-effectiveness.

Performance Degradation Prediction of Proton Exchange Membrane Fuel Cell Based on CEEMDAN-KPCA and DA-GRU Networks

In order to improve the performance degradation prediction accuracy of proton exchange membrane fuel cell(PEMFC),a fusion prediction method(CKDG)based on adaptive noise complete ensemble empirical mode decomposition(CEEMDAN),kernel principal component analysis(KPCA)and dual attention mechanism gated recurrent unit neural network(DA-GRU)was proposed.CEEMDAN and KPCA were used to extract the input feature data sequence,reduce the influence of random factors,and capture essential feature components to reduce the model complexity.The DA-GRU network helps to learn the feature mapping relationship of data in long time series and predict the changing trend of performance degradation data more accurately.The actual aging experimental data verify the performance of the CKDG method.The results show that under the steady-state condition of 20%training data prediction,the CKDA method can reduce the root mean square error(RMSE)by 52.7%and 34.6%,respectively,compared with the traditional LSTM and GRU neural networks.Compared with the simple DA-GRU network,RMSE is reduced by 15%,and the degree of over-fitting is reduced,which has higher accuracy.It also shows excellent prediction performance under the dynamic condition data set and has good universality.

Static superconducting gantry‑based proton CT combined with X‑ray CT as prior image for FLASH proton therapy

Proton FLASH therapy with an ultra-high dose rate is in urgent need of more accurate treatment plan system(TPS)to promote the development of proton computed tomography(CT)without intrinsic error compared with the transformation from X-ray CT.This paper presents an imaging mode of proton CT based on static superconducting gantry different from the conventional rotational gantry.The beam energy for proton CT is fixed at 350 MeV,which is boosted by a compact proton linac from 230 MeV,and then delivered by the gantry to scan the patient’s body for proton imaging.This study demonstrates that the static superconducting gantry-based proton CT is effective in clinical applications.In particular,the imaging mode,which combines the relative stopping power(RSP)map from X-ray CT as prior knowledge,can produce much a higher accuracy RSP map for TPSs and positioning and achieve ultra-fast image for real-time image-guided radiotherapy.This paper presents the conceptual design of a boosting linac,static superconducting gantry and proton CT imaging equipment.The feasibility of energy enhancement is verified by simulation,and results from Geant4 simulations and reconstruction algorithms are presented,including the simulation verification of the advantage of the imaging mode.

Simulation of the characteristics of low-energy proton induced single event upset

Monte Carlo simulation results are reported on the single event upset(SEU) triggered by the direct ionization effect of low-energy proton. The SEU cross-sections on the 45 nm static random access memory(SRAM) were compared with previous research work, which not only validated the simulation approach used herein, but also exposed the existence of saturated cross-section and the multiple bit upsets(MBUs) when the incident energy was less than 1 MeV. Additionally, it was observed that the saturated cross-section and MBUs are involved with energy loss and critical charge. The amount of deposited charge and the distribution with respect to the critical charge as the supplemental evidence are discussed.