Effects of Potassium Ferrate and Low-Temperature Thermal Hydrolysis Co-Pretreatment on the Hydrolysis and Anaerobic Digestion Process of Waste Activated Sludge

This study evaluated the effect of potassium ferrate(PF)and low-temperature thermal hydrolysis co-pretreatment on the promotion of sludge hydrolysis process and the impact on acid production in the subsequent anaerobic digestion process.The analytical investigations showed that co-pretreatment significantly facilitated the hydrolysis process of the sludge and contributed to the accumulation of short-chain fatty acids(SCFAs).The pretreatment conditions under the optimal leaching of organic matter from sludge were hydrothermal temperature of 75℃,hydrothermal treatment time of 12 h,and PF dosage of 0.25 g g^(−1)TSS(total suspended solids),according to the results of orthogonal experiments.By pretreatment under proper conditions,the removal rate of soluble chemical oxygen demand(SCOD)achieved 71.8%at the end of fermentation and the removal rate of total phosphorus(TP)was 69.1%.The maximum yield of SCFAs was 750.3 mg L^(−1),7.45 times greater than that of the blank group.Based on the analysis of the anaerobic digestion mechanism,it was indicated that the co-pretreatment could destroy the floc structure on the sludge surface and improve organic matter dissolving,resulting in more soluble organic substances for the acidification process.Furthermore,microbial community research revealed that the main cause of enhanced SCFAs generation was an increase in acidogenic bacteria and a reduction of methanogenic bacteria.

Deterioration of equivalent thermal conductivity of granite subjected to heating-cooling treatment

Understanding the thermal conductivity of granite is critical for many geological and deep engineering applications.The heated granite was subjected to air-,water-,and liquid nitrogen(LN2-)coolings in this context.The transient hot-wire technique was used to determine the equivalent thermal conductivity(ETC)of the granite before and after treatment.The deterioration mechanism of ETC is analyzed from the meso-perspective.Finally,the numerical model is used to quantitatively study the impact of cooling rate on the microcrack propagation and heat conduction characteristics of granite.The results show that the ETC of granite is not only related to the heating temperature,but also affected by the cooling rate.The ETC of granite decreases nonlinearly with increasing heating temperature.A faster cooling rate causes a greater decrease in ETC at the same heating temperature.The higher the heating temperature,the stronger the influence of cooling rate on ETC.The main explanation for the decrease in ETC of granite is the increase in porosity and microcrack density produced by the formation and propagation of pore structure and microcracks during heating and cooling.Further analysis displays that the damage of granite at the heating stage is induced by the difference in thermal expansion and elastic properties of mineral particles.At the cooling stage,the faster cooling rate causes a higher temperature gradient,which in turn produces greater thermal stress.As a result,it not only causes new cracks in the granite,but also aggravates the damage at the heating stage,which induces a further decrease in the heat conduction performance of granite,and this scenario is more obvious at higher temperatures.

Recent progresses in thermal treatment of β-Ga_(2)O_(3) single crystals and devices

In recent years,ultra-wide bandgap β-Ga_(2)O_(3) has emerged as a fascinating semiconductor material due to its great potential in power and photoelectric devices.In semiconductor industrial,thermal treatment has been widely utilized as a convenient and effective approach for substrate property modulation and device fabrication.Thus,a thorough summary of β-Ga_(2)O_(3) substrates and devices behaviors after high-temperature treatment should be significant.In this review,we present the recent advances in modulating properties of β-Ga_(2)O_(3) substrates by thermal treatment,which include three major applications:(ⅰ)tuning surface electrical properties,(ⅱ)modifying surface morphology,and(ⅲ)oxidating films.Meanwhile,regulating electrical contacts and handling with radiation damage and ion implantation have also been discussed in device fabrication.In each category,universal annealing conditions were speculated to figure out the corresponding problems,and some unsolved questions were proposed clearly.This review could construct a systematic thermal treatment strategy for various purposes and applications of β-Ga_(2)O_(3).

Characterization of Pr-CeO_2 Nano-crystallites Prepared by Low-temperature Combustion&Hydrothermal Synthesis

Pr-CeO2 Nano-crystalline red pigments were prepared by low-temperature combustion with a later hydrothermal treatment using Ce（NO3）3·6H2O and Pr6O11 as raw materials. The phase composition, coloring mechanism and morphology of pigments were analyzed by XRD, SEM, EDS and XPS. Results showed that Pr-CeO2 solid solution with a fluorite structure was obtained by the diffusion of Pr^＋3 into CeO2 crystal lattice during the synthesis process. XPS analysis indicated that Pr^＋3 substitutes Ce^＋4 in CeO2 and is compensated by oxygen vacancies. Compared with low-temperature combustion synthesis, the Pr-CeO2 pigments prepared with a subsequent hydrothermal treatment have an average grain size of about 16.70 nm, and the crystallinity and red tonality are improved.

The effects of radio frequency atmospheric pressure plasma and thermal treatment on the hydrogenation of TiO_(2) thin film

The effects of radio frequency(RF)atmospheric pressure(AP)He/H_(2)plasma and thermal treatment on the hydrogenation of TiO_(2)thin films were investigated and compared in this work.The color of the original TiO_(2)film changes from white to black after being hydrogenated in He/H_(2)plasma at160 W(gas temperature~381℃)within 5 min,while the color of the thermally treated TiO_(2)film did not change significantly even in pure H_(2)or He/H_(2)atmosphere with higher temperature(470℃)and longer time(30 min).This indicated that a more effective hydrogenation reaction happened through RF AP He/H_(2)plasma treatment than through pure H_(2)or He/H_(2)thermal treatment.The color change of TiO_(2)film was measured based on the Commission Internationale d’Eclairage L*a*b*color space system.Hydrogenated TiO_(2)film displayed improved visible light absorption with increased plasma power.The morphology of the cauliflower-like nanoparticles of the TiO_(2)film surface remained unchanged after plasma processing.X-ray photoelectron spectroscopy results showed that the contents of Ti3+species and Ti-OH bonds in the plasma-hydrogenated black TiO_(2)increased compared with those in the thermally treated TiO_(2).X-ray diffraction(XRD)patterns and Raman spectra indicated that plasma would destroy the crystal structure of the TiO_(2)surface layer,while thermal annealing would increase the overall crystallinity.The different trends of XRD and Raman spectra results suggested that plasma modification on the TiO_(2)surface layer is more drastic than on its inner layer,which was also consistent with transmission electron microscopy results.Optical emission spectra results suggest that numerous active species were generated during RF AP He/H_(2)plasma processing,while there were no peaks detected from thermal processing.A possible mechanism for the TiO_(2)hydrogenation process by plasma has been proposed.Numerous active species were generated in the bulk plasma region,accelerated in the sheath region,and bumped toward the TiO_(2)film,which will react with the TiO_(2)surface to form OVs and disordered layers.This leads to the tailoring of the band gap of black TiO_(2)and causes its light absorption to extend into the visible region.

Synergistically Improved Mechanical Properties and Thermal Conductivity of Hypoeutectic AlSiNiFeMg Alloy Prepared by Ultrasonic-assisted Casting

We employed a melt ultrasonic treatment near the liquidus to prepare a high-thermal-conductivity Al-4Si-2Ni-0.8Fe-0.4Mg alloy.The influences of various ultrasonic powers on its microstructure,mechanical properties,and thermal conductivity were investigated.It is shown that near-liquidus ultrasonication significantly refines the alloy grains and eutectic structure,synergistically improving the alloy’s mechanical properties and thermal conductivity.Specifically,the grain size decreased by 84.5%from 941.4 to 186.2μm.Increasing the ultrasonic power improved the thermal conductivity of the alloy slightly and significantly enhanced its mechanical properties.At an ultrasonic power of 2100 W,the tensile strength,yield strength,elongation rate,and thermal conductivity were 216 MPa,142 MPa,6.3%,and 169 W/(m·k),respectively.

Comparison of microwave- and thermal-assisted rock fragmentation methods at different temperatures and loading rates

Understanding the effects of microwave irradiation and thermal treatment on the dynamic compression and fragmentation properties of rocks is essential to quantify energy consumption in rock engineering.In this study,Fangshan granite(FG)specimens were exposed to microwave irradiation and heat treatment.The damage of FG specimens induced by these two methods was compared using X-ray CT scanning and ultrasonic wave method.The temperatures of FG after microwave irradiation and thermal treatment were effectively evaluated using a newly proposed technique.A novelty method for precisely determining the geometric features of fragments is developed to estimate the fragmentation energy.Thus,the dynamic uniaxial compressive strength(UCS),the dynamic fragmentation characteristics,and the fragmentation energy of FG after these two pretreatment methods can be reasonably compared.The noticeable distinction of loading rate effect on the dynamic UCS of FG between these two pretreatment methods is first observed.A relationship is established between the dynamic UCS and the damage induced by microwave irradiation and heat treatment.Moreover,fragmentation energy fan analysis is introduced to accurately compare the fragmentation properties of FG after two pretreatment methods in dynamic compression tests.

Improving thermal conductivity of Mg-Si-Zn-Cu alloy through minimizing electron scattering at phase interface

The primary cause of the decrease in thermal conductivity of conventional thermal conductive magnesium alloys is electron scattering brought on by solute atoms.However,the impact of phase interface on thermal conductivity of magnesium alloys is usually disregarded.This study has developed a Mg-Si-Zn-Cu alloy with high thermal conductivity that is distinguished by having a very low solute atom content and a significant number of phase interfaces.The thermal conductivity of the Mg^(-1).38Si-0.5Zn-0.5Cu alloy raises from its untreated value of 133.2 W/(m·K)to 142.2 W/(m·K),which is 91%of the thermal conductivity of pure Mg.This is accomplished by subjecting the alloy to both 0.8wt%Ce modification and T6 heat treatment.The morphology of eutectic Mg_(2)Si phase is changed by Ce modification and heat treatment,and as a result,the scattering of electrons at the Mg_(2)Si/Mg interface is reduced,resulting in increase of the alloy’s thermal conductivity.

Mechanical properties and fracture surface roughness of thermally damaged granite under dynamic splitting

In order to understand the mechanical properties and the fracture surface roughness characteristics of thermally damaged granite under dynamic splitting,dynamic Brazilian splitting tests were conducted on granite samples after thermal treatment at 25,200,400,and 600℃.Results show that the dynamic peak splitting strength of thermally damaged granite samples increases with increasing strain rate,showing obvious strain‐rate sensitivity.With increasing temperature,thermally induced cracks in granite transform from intergranular cracks to intragranular cracks,and to a transgranular crack network.Thermally induced damages reduce the dynamic peak splitting strength and the maximum absorbed energy while increasing the peak radial strain.The fracture mode of the thermally damaged granite under dynamic loads is mode Ⅱ splitting failure.By using the axial roughness index Z2 a,the distribution ranges of the wedge‐shaped failure zones and the tensile failure zones in the fracture surfaces under dynamic Brazilian splitting can be effectively identified.The radial roughness index Z_(2)^(r)is sensitive to the strain rate and temperature.It shows a linear correlation with the peak splitting strength and the maximum absorbed energy and a linear negative correlation with the peak radial strain.Z_(2)^(r)can be used to quantitatively estimate the dynamic parameters based on the models proposed.

Comparison of mechanical properties in high temperature and thermal treatment granite

Static mechanical experiments were carried out on granite after and under different temperatures using an electro-hydraulic and servo-controlled material testing machine with a heating device. Variations in obvious form, stress-strain curve, peak strength, peak strain and elastic modulus with temperature were analyzed and the essence of rock failure modes was explored. The results indicate that, compared with granite after the high temperature treatment, the brittle-ductile transition critical temperature is lower, the densification stage is longer, the elastic modulus is smaller and the damage is larger under high temperature. In addition, the peak stress is lower and the peak strain is greater, but both of them change more obviously with the increase of temperature compared with that of granite after the high temperature treatment. Furthermore, the failure modes of granite after the high temperature treatment and under high temperature show a remarkable difference. Below 100 ℃, the failure modes of granite under both conditions are the same, presenting splitting failure. However, after 100 ℃, the failure modes of granite after the high temperature treatment and under high temperature present splitting failure and shear failure, respectively.

Microstructure evolution and thermal expansion of Cu-Zn alloy after high pressure heat treatment

The thermal expansion coefficients of Cu-Zn alloy before and after high pressure treatment were measured by thermal expansion instrument in the temperature range of 25？700 ℃,and the microstructure and phase transformation of the alloy were examined by optical microscope,X-ray diffractometer（XRD） and differential scanning calorimeter（DSC）.Based on the experimental results,the effects of high pressure treatment on the microstructure and thermal expansion of Cu-Zn alloy were investigated.The results show that the high pressure treatment can refine the grain and increase the thermal expansion coefficient of the Cu-Zn alloy,resulting in that the thermal expansion coefficient exhibits a high peak value on the α-T curve,and the peak value decreases with increasing the pressure.

Thermal Treatment for Decreasing the Acidity of Crude Oil

Highly acidic crude oil is thermally soaked to investigate how the temperature and time involved affect the removal of organic acid in feedstock. Experimental results indicate that thermal treatment is an effective approach to decreasing acidity and the acid removal rate reaches 80%. Temperature is one of the main factors that determine the acid removal reaction. When the temperature ranges from 420oC to 440oC, the acid removal rate increases with the rise of the reaction temperature, but the increase slows down gradually. At the reaction temperature below 440oC, the long reaction time favors the acid removal. The cracking and polymerization of hydrocarbon molecules take place so that the properties of the crude oil change at the same time when the highly acidic crude is thermally treated.

Effect of Low-Temperature Thermal Oxidation on the Capillary Performance of Sintered Copper Powder Wicks

In this study,a composite powder capillary wick is prepared,manufactured by sintering copper powder and surface treated by low-temperature thermal oxidation.It is used to improve the performance of the capillary wick.The forced flow method and infrared imaging method are used to test the permeability and capillary performance of the samples.The effects of different oxidation temperatures on the performance of capillary wick are investigated.The experimental results show that the wetting performance of the oxidized samples is significantly enhanced.With the increase of oxidation temperature,the permeability decreases.The capillary height and velocity of the thermally oxidized samples are significantly higher than those of the untreated capillary wick.However,the oxidation temperature needs to be adjusted to obtain the best capillary performance.The highest capillary performance is found at oxidation temperature of 300℃,with an increase of 46% compared to the untreated ones.Comparisons with other composite wicks show that the sample with an oxidation temperature of 300℃ has competitive capillary performance,making it a favorable alternative to two-phase heat transfer device.This study shows that combining low-temperature thermal oxidation technology with powder sintering is a convenient and effective method to improve the capillary performance of powder wicks.

THERMAL RATE TREATMENT AND ITS EFFECT ON MODIFICATION OF Al-Si ALLOYS

ＴＨＥＲＭＡＬＲＡＴＥＴＲＥＡＴＭＥＮＴＡＮＤＩＴＳＥＦＦＥＣＴＯＮＭＯＤＩＦＩＣＡＴＩＯＮＯＦＡｌＳｉＡＬＬＯＹＳ①ＧｅｎｇＨａｏｒａｎ，ＭａＪｉａｊｉ，ＢｉａｎＸｏｕｆａｎｇＣｏｌｌｅｇｅｏｆＭａｔｅｒｉａｌｓＳｃｉｅｎｃｅａｎｄＥｎｇｉｎｅｒ...

Effects of cryogenic treatment on the thermal physical properties of Cu_(76.12) Al_(23.88) alloy

The thermal diffusion coefficient, heat capacity, thermal conductivity, and thermal expansion coefficient of Cu76.12Al23.88 alloy before and after cryogenic treatment in the heating temperature range of 25℃ to 600℃ were measured by thermal constant tester and thermal expansion instrument. The effects of cryogenic treatment on the thermal physical properties of CU76,12A123,88 alloy were investigated by comparing the variation of the thermal parameters before and after cryogenic treatment. The results show that the variation trend of the thermal diffusion coefficient, heat capacity, thermal conductivity, and thermal expansion coefficient of CU76.12Al23.88 alloy after cryogenic treatment was the same as before. The cryogenic treatment can increase the thermal diffusion coefficient, thermal conductivity, and thermal expansion coeffi- cient of Cu76.12Al23.88 alloy and decrease its heat capacity. The maximum difference in the thermal diffusion coefficient between the before and after cryogenic treatment appeared at 400℃. Similarly, thermal conductivity was observed at 200℃.

Improved Multiple Feature-electrochemical Thermal Coupling Modeling of Lithium-ion Batteries at Low-temperature with Real-time Coefficient Correction

Monitoring various internal parameters plays a core role in ensuring the safety of lithium-ion batteries in power supply applications.It also influences the sustainability effect and online state of charge prediction.An improved multiple feature-electrochemical thermal coupling modeling method is proposed considering low-temperature performance degradation for the complete characteristic expression of multi-dimensional information.This is to obtain the parameter influence mechanism with a multi-variable coupling relationship.An optimized decoupled deviation strategy is constructed for accurate state of charge prediction with real-time correction of time-varying current and temperature effects.The innovative decoupling method is combined with the functional relationships of state of charge and open-circuit voltage to capture energy management ef-fectively.Then,an adaptive equivalent-prediction model is constructed using the state-space equation and iterative feedback correction,making the proposed model adaptive to fractional calculation.The maximum state of charge estimation errors of the proposed method are 4.57% and 0.223% under the Beijing bus dynamic stress test and dynamic stress test conditions,respectively.The improved multiple feature-electrochemical thermal coupling modeling realizes the effective correction of the current and temperature variations with noise influencing coefficient,and provides an efficient state of charge prediction method adaptive to complex conditions.

Effect of thermal treatment on energy dissipation of granite under cyclic impact loading

High temperature treatment causes thermal damage to rocks in deep mining.To study the thermal effect on the energy dissipation of rocks during the dynamic cyclic loading,cyclic impact loading experiments of heat-treated rocks were carried out using the splitting Hopkinson pressure bar(SHPB)experimental system.The correlations among the energy dissipation,energy dissipation rate,impact times,accumulated absorbed energy per volume,failure mode and temperature were analyzed.The results show that the reflected energy under the first impact increases and finally exceeds the absorbed energy when the temperature increases;however,the total reflected energy decreases above 200℃.The absorbed energy under the first impact and the total absorbed energy all decrease as the temperature increases,the rates of which decrease accordingly.And the same phenomenon appears for the transmitted energy and the rate of the transmitted energy.On the contrary,the rate of the reflected energy increases with the rising temperature.When the temperature increases,the fewer impact times are needed to destroy the sample.In addition,the failure modes are different when the rock is treated at different temperatures;that is,when the temperature is high,even though the absorbed energy is low,the sample breaks into powder after several impacts.

Numerical Simulation on Thermal Stress of Large-scale Bearing Roller during Heating Process of Final Heat Treatment

hi this paper, the non-linear finite element method had been applied to calculate the thermal stress evolving process of the large-scale bearing roller during heating process of final heat treatment. It was found that two stress peaks appeared during heating process and the second stress peak was higher than the first. If the preheating time was elongated, the second stress peak was reduced distinctly. Therefore, the pre-heating time should be elongated suitably to ensure safety in the practical manufacture process.

Influence of Thermal Treatments on In-depth Compositional Uniformity of Culn（S,Se）2 Thin Films

CuIn（S,Se）2 thin films were prepared by thermal crystallization of co-sputtered Cu-In alloy precursors in S/Se atmosphere. In-depth compositional uniformity is an important prereq- uisite for obtaining device-quality CuIn（S,Se）2 absorber thin films. In order to figure out the influence of heat treatments on in-depth composition uniformity of CuIn（S,Se）2 thin films, two kinds of reaction temperature profiles were investigated. One process is ＂one step profile＂, referring to formation of CuIn（S,Se）2 thin films just at elevated temperature （e.g. 500 ℃）. The other is ＂two step profile＂, which allows for slow diffusion of S and Se elements into the alloy precursors at a low temperature before the formation and re-crystallization of CuIn（S,Se）2 thin films at higher temperature （e.g. first 250 ℃ then 500 ℃）. X-ray diffrac- tion studies reveal that there is a discrepancy in the shape of （112） peak. Samples annealed with ＂one step profile＂ have splits on （112） peaks, while samples annealed with ＂two step profile＂ have relatively symmetrical （112） peaks. Grazing incident X-ray diffraction and en- ergy dispersive spectrum measurements of samples successively etched in bromine methanol show that CuIn（S,Se）2 thin films have better in-depth composition uniformity after ＂two step profile＂ annealing. The reaction mechanism during the two thermal processing was also investigated by X-ray diffraction and Raman spectra.

Effects of Chemical Treatments on Thermal Expansion Properties of Cordierite Ceramics

Cordierite honeycomb ceramics was treated with 1.5 M HNO3 , followed with 1.5 M NaOH at 93 ℃. The combination of acid treatment with alkali treatment significantly diminished the rebounding of coefficient of thermal expansion （CTE） caused by heat treatment, a phenomenon observed in samples treated solely with acid. Inductively coupled plasma （ICP） analysis results reveal that the alkali treatment preferentially dissolved ＂free＂ SiO2 left in the acid-treated samples, which is considered to be a key factor responsible for the CTE rebounding.