Due to its low cost and natural abundance of sodium,Na-ion batteries(NIBs)are promising candidates for large-scale energy storage systems.The development of ultralow voltage anode materials is of great significance in...Due to its low cost and natural abundance of sodium,Na-ion batteries(NIBs)are promising candidates for large-scale energy storage systems.The development of ultralow voltage anode materials is of great significance in improving the energy density of NIBs.Low-voltage anode materials,however,are severely lacking in NIBs.Of all the reported insertion oxides anodes,the Na_(2)Ti_(3)O_(7) has the lowest operating voltage(an average potential of 0.3 V vs.Na^(+)/Na)and is less likely to deposit sodium,which has excellent potential for achieving NIBs with high energy densities and high safety.Although significant progress has been made,achieving Na_(2)Ti_(3)O_(7) electrodes with excellent performance remains a severe challenge.This paper systematically summarizes and discusses the physicochemical properties and synthesis methods of Na_(2)Ti_(3)O_(7).Then,the sodium storage mechanisms,key issues and challenges,and the optimization strategies for the electrochemical performance of Na_(2)Ti_(3)O_(7) are classified and further elaborated.Finally,remaining challenges and future research directions on the Na_(2)Ti_(3)O_(7) anode are highlighted.This review offers insights into the design of high-energy and high-safety NIBs.展开更多
The generation of photovoltaic(PV)solar energy is increasing continuously because it is renewable,unlimited,and clean energy.In the past,generation systems depended on non-renewable sources such as oil,coal,and gas.Th...The generation of photovoltaic(PV)solar energy is increasing continuously because it is renewable,unlimited,and clean energy.In the past,generation systems depended on non-renewable sources such as oil,coal,and gas.Therefore,this paper assesses the performance of a 51 kW PV solar power plant connected to a low-voltage grid to feed an administrative building in the 6th of October City,Egypt.The performance analysis of the considered grid-connected PV system is carried out using power system simulator for Engineering(PSS/E)software.Where the PSS/E program,monitors and uses the power analyzer that displays the parameters and measures some parameters such as current,voltage,total power,power factor,frequency,and current and voltage harmonics,the used inverter from the type of grid inverter for the considered system.The results conclude that when the maximum solar radiation is reached,the maximum current can be obtained from the solar panels,thus obtaining the maximum power and power factor.Decreasing total voltage harmonic distortion,a current harmonic distortion within permissible limits using active harmonic distortion because this type is fast in processing up to 300 microseconds.The connection between solar stations and the national grid makes the system more efficient.展开更多
The increasing proportion of distributed photovoltaics(DPVs)and electric vehicle charging stations in low-voltage distribution networks(LVDNs)has resulted in challenges such as distribution transformer overloads and v...The increasing proportion of distributed photovoltaics(DPVs)and electric vehicle charging stations in low-voltage distribution networks(LVDNs)has resulted in challenges such as distribution transformer overloads and voltage violations.To address these problems,we propose a coordinated planning method for flexible interconnections and energy storage systems(ESSs)to improve the accommodation capacity of DPVs.First,the power-transfer characteristics of flexible interconnection and ESSs are analyzed.The equipment costs of the voltage source converters(VSCs)and ESSs are also analyzed comprehensively,considering the differences in installation and maintenance costs for different installation locations.Second,a bilevel programming model is established to minimize the annual comprehensive cost and yearly total PV curtailment capacity.Within this framework,the upper-level model optimizes the installation locations and capacities of the VSCs and ESSs,whereas the lower-level model optimizes the operating power of the VSCs and ESSs.The proposed model is solved using a non-dominated sorting genetic algorithm with an elite strategy(NSGA-II).The effectiveness of the proposed planning method is validated through an actual LVDN scenario,which demonstrates its advantages in enhancing PV accommodation capacity.In addition,the economic benefits of various planning schemes with different flexible interconnection topologies and different PV grid-connected forms are quantitatively analyzed,demonstrating the adaptability of the proposed coordinated planning method.展开更多
A novel structure of low-voltage trigger silicon-controlled rectifiers(LVTSCRs) with low trigger voltage and high holding voltage is proposed for electrostatic discharge(ESD) protection. The proposed ESD protection de...A novel structure of low-voltage trigger silicon-controlled rectifiers(LVTSCRs) with low trigger voltage and high holding voltage is proposed for electrostatic discharge(ESD) protection. The proposed ESD protection device possesses an ESD implant and a floating structure. This improvement enhances the current discharge capability of the gate-grounded NMOS and weakens the current gain of the silicon-controlled rectifier current path. According to the simulation results, the proposed device retains a low trigger voltage characteristic of LVTSCRs and simultaneously increases the holding voltage to 5.53 V, providing an effective way to meet the ESD protection requirement of the 5 V CMOS process.展开更多
Fluoride and nitrate enriched groundwater are potential threats to the safety of the groundwater supply that may cause significant effects on human health and public safety,especially in aggregated population areas an...Fluoride and nitrate enriched groundwater are potential threats to the safety of the groundwater supply that may cause significant effects on human health and public safety,especially in aggregated population areas and economic hubs.This study focuses on the high F^(−)and NO_(3)^(−)concentration groundwater in Tongzhou District,Beijing,North China.A total of 36 groundwater samples were collected to analyze the hydrochemical characteristics,elucidate genetic mechanisms and evaluate the potential human health risks.The results of the analysis indicate:Firstly,most of the groundwater samples are characterized by Mg-HCO_(3) and Na-HCO_(3) with the pH ranging from 7.19 to 8.28 and TDS with a large variation across the range 471-2337 mg/L.The NO_(3)^(−)concentration in 38.89%groundwater samples and the F^(−)concentration in 66.67%groundwater samples exceed the permissible limited value.Secondly,F^(−)in groundwater originates predominantly from water-rock interactions and the fluorite dissolution,which is also regulated by cation exchange,competitive adsorption of HCO_(3)−and an alkaline environment.Thirdly,the effect of sewage disposal and agricultural activities have a significant effect on high NO3-concentration,while the high F^(−)concentration is less influenced by anthropogenic activity.The alkaline environment favors nitrification,thus being conducive to the production of NO_(3)^(−).Finally,the health risk assessment is evaluated for different population groups.The results indicate that high NO_(3)^(−)and F^(−)concentration in groundwater would have the largest threat to children’s health.The findings of this study could contribute to the provision of a scientific basis for groundwater supply policy formulation relating to public health in Tongzhou District.展开更多
Drip irrigation and flood irrigation are major irrigation methods for maize crops in the Hetao Irrigation District,Inner Mongolia Autonomous Region,China.This research delves into the effects of these irrigation metho...Drip irrigation and flood irrigation are major irrigation methods for maize crops in the Hetao Irrigation District,Inner Mongolia Autonomous Region,China.This research delves into the effects of these irrigation methods on carbon dioxide(CO_(2))exchange and crop growth in this region.The experimental site was divided into drip and flood irrigation zones.The irrigation schedules of this study aligned with the local commonly used irrigation schedule.We employed a developed chamber system to measure the diurnal CO_(2)exchange of maize plants during various growth stages under both drip and flood irrigation methods.From May to September in 2020 and 2021,two sets of repeated experiments were conducted.In each experiment,a total of nine measurements of CO_(2)exchange were performed to obtain carbon exchange data at different growth stages of maize crop.During each CO_(2)exchange measurement event,CO_(2)flux data were collected every two hours over a day-long period to capture the diurnal variations in CO_(2)exchange.During each CO_(2)exchange measurement event,the biological parameters(aboveground biomass and crop growth rate)of maize and environmental parameters(including air humidity,air temperature,precipitation,soil water content,and photosynthetically active radiation)were measured.The results indicated a V-shaped trend in net ecosystem CO_(2)exchange in daytime,reducing slowly at night,while the net assimilation rate(net primary productivity)exhibited a contrasting trend.Notably,compared with flood irrigation,drip irrigation demonstrated significantly higher average daily soil CO_(2)emission and greater average daily CO_(2)absorption by maize plants.Consequently,within the maize ecosystem,drip irrigation appeared more conducive to absorbing atmospheric CO_(2).Furthermore,drip irrigation demonstrated a faster crop growth rate and increased aboveground biomass compared with flood irrigation.A strong linear relationship existed between leaf area index and light utilization efficiency,irrespective of the irrigation method.Notably,drip irrigation displayed superior light use efficiency compared with flood irrigation.The final yield results corroborated these findings,indicating that drip irrigation yielded higher harvest index and overall yield than flood irrigation.The results of this study provide a basis for the selection of optimal irrigation methods commonly used in the Hetao Irrigation District.This research also serves as a reference for future irrigation studies that consider measurements of both carbon emissions and yield simultaneously.展开更多
In the economic development of Beijing,although the share of the total amount of agricultural industry in the overall economy is relatively low,it has an important impact on the daily life of residents,social stabilit...In the economic development of Beijing,although the share of the total amount of agricultural industry in the overall economy is relatively low,it has an important impact on the daily life of residents,social stability and the development of other industries.Changping District,as an important agricultural production base of Beijing,its agricultural development has an indispensable strategic significance for the stability and growth of the entire regional economy.Therefore,it is very important to study the structure of agricultural industry in Changping District.Based on the detailed analysis of the agricultural industrial structure of Changping District,this paper uses the grey relation theory to analyze the different industries in the agricultural industrial structure of Changping District,including planting,forestry,animal husbandry,fishery and agricultural,forestry,service industries,in order to reveal the impact of these industries on the agricultural industrial structure of Changping District.Through this study,it comes up with specific and feasible suggestions for the optimization of agricultural industrial structure in Changping District,and provides valuable reference for the agricultural development of other areas in Beijing.展开更多
With the rapid development of urban economy, distribution network construction of city is lagging behind the increment of load, and low-voltage problem has become the main complaints of the power users. Based on Pytho...With the rapid development of urban economy, distribution network construction of city is lagging behind the increment of load, and low-voltage problem has become the main complaints of the power users. Based on Python [1] scripting language, this paper develops a piece of software which can provide a friendly human-machine experience for the user, calculate the voltage of the power distribution area and propose corresponding control measures, then the paper takes the actual power distribution area to verify its effectiveness.展开更多
Scaling problems and limitations of conventional silicon transistors have led the designers to exploit novel nano-technologies. One of the most promising and feasible nano-technologies is CNT(Carbon Nanotube) based tr...Scaling problems and limitations of conventional silicon transistors have led the designers to exploit novel nano-technologies. One of the most promising and feasible nano-technologies is CNT(Carbon Nanotube) based transistors. In this paper, a high-speed and energy-efficient CNFET(Carbon Nanotube Field Effect Transistor) based Full Adder cell is proposed for nanotechnology. This design is simulated in various supply voltages, frequencies and load capacitors using HSPICE circuit simulator. Significant improvement is achieved in terms of speed and PDP(Power-Delay-Product) in comparison with other classical and state-of-the-art CMOS and CNFET-based designs, existing in the literature. The proposed Full Adder can also drive large load capacitance and works properly in low supply voltages.展开更多
Powder metallurgy is an efficient approach to fabricate varieties of high performance structure materials, function materials and special materials working under limited conditions. Research and development of new eff...Powder metallurgy is an efficient approach to fabricate varieties of high performance structure materials, function materials and special materials working under limited conditions. Research and development of new efficient technology to form high-density, high-performance and net shape parts is a key to widen application and development of powder materials. Recently, the low-voltage electromagnetic compaction (EMC) has been used by present authors to compacted copper, tin, aluminum powders and the products with 99% relative density have been acquired. In this work, the research has been extended to investigation on the density uniformity of pressed parts. The analysis results show that the density of the part compacted by low-voltage EMC decreases gradually in press direction as static compaction. But it is higher and more homogeneous. The density of the top part increases gradually from the center to the outer, which is just reversal of the bottom part. In some extent, the higher the discharging voltage is, the higher the density is and the more homogeneous the distribution is. In addition, repetitive compaction can improve the density of powder parts and the distribution uniformity.展开更多
Low-voltage electromagnetic compaction (EMC) was used to compact metal powders (Cu) and ceramic powders (TiO2) in the indirect way. It was found that the density of the metal powder parts compacted by low-voltag...Low-voltage electromagnetic compaction (EMC) was used to compact metal powders (Cu) and ceramic powders (TiO2) in the indirect way. It was found that the density of the metal powder parts compacted by low-voltage EMC varied linearly with the discharging voltage in the range investigated. But for ceramic powders, the discharging voltage has an optimal value. Under the value, the density increases as discharging voltage rises, but beyond the value the trend is reverse. The experimental results show that the density of the metal parts decreases gradually along press direction. And the density of the ceramic parts decreases with the advancement of the aspect ratio h/d (height/diameter). In addition, repetitive compaction can improve the density of both metal and ceramic parts and reduce the effects of aspect ratio on the density.展开更多
This paper is devoted to the simulation of the arc plasma in a simplified low-voltage circuit breaker chamber. Based on a group of coupled governing equations, a three-dimensional (3-D) arc plasma model is built and...This paper is devoted to the simulation of the arc plasma in a simplified low-voltage circuit breaker chamber. Based on a group of coupled governing equations, a three-dimensional (3-D) arc plasma model is built and solved by a modified commercial code. Firstly, this paper presents a solution of the stationary state of the arc plasma and discusses the distribution of some parameters throughout the chamber. Secondly, with the ferromagnetic materials included, the balance of the stationary state is broken and a transient course is calculated. In light of the simulation results, the temperature distribution sequence, the arc motion and the plasma jet are then described and analyzed in detail.展开更多
Low-voltage distribution systems in our country are mostly used in agricultural loads and household loads. The value and using time of these kinds of loads are uncontrollable, which lead to the three-phase imbalance i...Low-voltage distribution systems in our country are mostly used in agricultural loads and household loads. The value and using time of these kinds of loads are uncontrollable, which lead to the three-phase imbalance in low-voltage distribution system, and seriously affect the quality of power supply. A new type of the commutation system and an improved quantum genetic algorithm (IQGA) are proposed in the paper. At last, the rationality and the efficiency of the method are verified by a practical example.展开更多
This paper focuses on the simulation of the low-voltage arc with an opening contact. A controllable experiment setup with a rotating contact is designed to investigate the arc behaviour. Supported by the experiment, t...This paper focuses on the simulation of the low-voltage arc with an opening contact. A controllable experiment setup with a rotating contact is designed to investigate the arc behaviour. Supported by the experiment, the phenomena of arc elongation and commutation in the case of rotating contact are simulated with the dynamic grid technique introduced. Under the given condition of the external magnetic field and the contact rotating velocity, the stagnation and rapid jump of two arc roots are observed by the calculated and experimental arc root displacement. The voltage of arc column can be divided into four phases and its sharp rising progress comes from the increase of the displacement difference between two arc roots in x direction.展开更多
The low-voltage-electromagnetic forming was applied to powder compaction.A series of experiments was performed to compact aluminum,copper and tin powders in an indirect working way.Having compacted high-density powder...The low-voltage-electromagnetic forming was applied to powder compaction.A series of experiments was performed to compact aluminum,copper and tin powders in an indirect working way.Having compacted high-density powder parts successfully,the authors analyzed the effects of voltage,capacitance,friction,compaction times,powder size and other factors on the densities of compacted specimens.The experimental results show that lower voltage but larger capacitance are beneficial to increasing the density and homogeneity of the compacted specimens,if the loading velocity and discharging energy are suitable.The higher the voltage,the greater the percentage of energy consumed by friction.If the equipment energy is limited,the iterative compaction is an efficient way to manufacture homogeneous and high-density powder parts.展开更多
Planar radio frequency inductively coupled plasmas(ICP) are employed for low-voltage ion implantation processes,with capacitive pulse biasing of the substrate for modulation of the ion energy. In this work, a two-di...Planar radio frequency inductively coupled plasmas(ICP) are employed for low-voltage ion implantation processes,with capacitive pulse biasing of the substrate for modulation of the ion energy. In this work, a two-dimensional(2D) selfconsistent fluid model has been employed to investigate the influence of the pulsed bias power on the nitrogen plasmas for various bias voltages and pulse frequencies. The results indicate that the plasma density as well as the inductive power density increase significantly when the bias voltage varies from 0 V to-4000 V, due to the heating of the capacitive field caused by the bias power. The N+fraction increases rapidly to a maximum at the beginning of the power-on time, and then it decreases and reaches the steady state at the end of the glow period. Moreover, it increases with the bias voltage during the power-on time, whereas the N2-+ fraction exhibits a reverse behavior. When the pulse frequency increases to 25 kHz and40 kHz, the plasma steady state cannot be obtained, and a rapid decrease of the ion density at the substrate surface at the beginning of the glow period is observed.展开更多
In order to assess public effective dose due to gross alpha and beta in water, 43 tap water samples were collected from different areas in the District of Abidjan. Using the low background Gas-less Automatic Alpha/Bet...In order to assess public effective dose due to gross alpha and beta in water, 43 tap water samples were collected from different areas in the District of Abidjan. Using the low background Gas-less Automatic Alpha/Beta counting system (Canberra iMatic<sup>TM</sup>) for analysis, the gross alpha and beta concentrations found varied from 0.001 ± 0.002 to 0.063 ± 0.050 Bq/l with an average of 0.013 ± 0.012 Bq/l and from 0.067 ± 0.080 to 0.320 ± 0.120 Bq/l with an average of 0.174 ± 0.076 Bq/l, respectively in samples. The public effective dose assessment showed values of dose to ingestion of alpha and beta emitter radionuclides lower than the recommended value of dose for drinking water 0.1 mSv/y, except in 30% of the samples. These results show the need for additional studies to be conducted in order to clarify the hazardousness of these water samples. However, this study still remains important because it has provided necessary data for future tap water quality monitoring studies in the District of Abidjan.展开更多
Background: 25% of all people requiring surgical care are not able to access it due to its high cost. These people stand a high risk of preventable severe morbidity and mortality due to poor prognosis of surgically co...Background: 25% of all people requiring surgical care are not able to access it due to its high cost. These people stand a high risk of preventable severe morbidity and mortality due to poor prognosis of surgically correctable illnesses. Ambulatory surgical care services are significantly cheaper than orthodox surgical care and have become very relevant in this time and age where health conditions that can only be treated with surgical intervention are on the rise. The acceptability of ambulatory surgical care services will determine how this model increases universal health coverage. Objective: To assess the acceptability of ambulatory surgical services and its predictors among residents of Budondo Sub-County—Jinja district. Methods: The study was cross-sectional targeting 371 household heads in Budondo Sub-County, which was stratified by parish, with villages in each randomly sampled. Systematic random sampling was used to sample households and households therein were purposively sampled. Structured interviews and questionnaires were the data collection techniques, and data was analyzed in SPSS version 25 using descriptive statistics and a binomial logit model. Results: The level of acceptability of ambulatory surgical care services among residents of Budondo Sub-County was found to be near-universal, at 96.5%. The odds of accepting ambulatory surgical care were least among household heads who agreed that surgery done in a hospital would be cheaper than surgery done at community level (aOR = 0.174 [CI = 0.055 - 0.553]), those who had health insurance (aOR = 0.105 [95% CI = 0.030 - 0.371]), and household heads who were covered with private health insurance (aOR = 0.078 [95% CI = 0.008 - 0.792]). Acceptability of ASC was higher among household heads who agreed that they would trust ambulatory surgical centers with their life were more likely to accept ambulatory surgical care (aOR = 1.124, [95% CI = 1.122 - 3.218], P = 0.000), and household heads from households that had less than five members with surgery history were twice as likely to accept ambulatory surgical care (aOR = 2.431 [95% CI = 1.122 - 5.898], P = 0.000). Conclusion: Acceptability of ambulatory surgical care services among residents of Budondo Sub-County is high, and near-universal. It is mainly predicted by intrapersonal correlates and to a small extent by socio-demographic characteristics, with the implication that the administration of Global Surgical Initiatives in Kyabirwa ought to focus on modifying or uphold the intrapersonal characteristics found to be antagonists and protagonists of acceptability, respectively.展开更多
Labour-saving or mechanization technologies have become the driving force behind modern agriculture, yet adoption of these technologies remains low in many parts of the developing world, particularly among female farm...Labour-saving or mechanization technologies have become the driving force behind modern agriculture, yet adoption of these technologies remains low in many parts of the developing world, particularly among female farmers in Ghana. This study aims to investigate the factors that hinder the adoption of agricultural mechanization technologies by female farmers in the Karaga District of the Northern Region of Ghana. This region is known for its large agricultural lands and significant role in commercial farming. The research was conducted using qualitative research methodology and involved interviewing 60 female farmers using an interview guide. The principle of sample saturation was used, meaning that further interviews were deemed unnecessary after the 60th interview. The results showed that low adoption of agricultural mechanization technologies is due to poor access to commercial lands, gender biases, lack of access to credit, and poor awareness about the benefits of these technologies. In conclusion, the low adoption of agricultural mechanization technologies is preventing women farmers in the Karaga District and elsewhere in Ghana from fully participating in commercial agricultural production. It is recommended that gender biases and cultural stereotypes be addressed to improve women farmers’ access to lands and credit, which will facilitate the adoption of mechanization technologies and lead to improved agricultural production.展开更多
Teenage pregnancy is a common public health problem worldwide because teenagers in general are ill-prepared to deal with the burden of pregnancy. Sub-Saharan Africa has the highest burden of teenage pregnancy precisel...Teenage pregnancy is a common public health problem worldwide because teenagers in general are ill-prepared to deal with the burden of pregnancy. Sub-Saharan Africa has the highest burden of teenage pregnancy precisely in the west and central Africa;in Cameroon, about 12% of all births are to teenage mothers. Complications from pregnancy and childbirth are the leading cause of death among girls aged 15 to 19. Though the trend of teenage pregnancy tends to decrease in most parts of the world, this is not the case in our setting. The main aim of this study was to determine the prevalence, outcomes and the associated factors of teenage pregnancy in the Bamenda Health District (BHD). Materials and Method: This was a hospital-based cross-sectional descriptive and analytic study carried out at the maternity and postnatal units of the Bamenda Regional Hospital and the Nkwen Medicalised Health Center. A consecutive non-probabilistic sampling technique was used to recruit participants. A pretested questionnaire was used to collect information from the participant. Data was analysed using the software SPSS version 23. Bivariate logistic regression was used to test for associations. Statistical significance was set at p-value less than 0.05. Result: A total of 325 participants were recruited of which 44 were teenagers. The mean age of the participants was 25.02 ± 0.257 years. The mean age of teenagers was 17.49 ± 0.63 years, and mean adult age was 28.43 ± 5.64 years. The youngest participant was 15 years. Teenagers were significantly more likely to prematurity (OR = 0.14;95% CI = 0.06 - 0.31;PV = 0.001), Low birth weight among teenagers (OR = 0.077;95% CI = 0.03 - 0.21;PV = 0.001), Still birth;OR = 0.07;95% CI = 0.01 - 0.86;PV = 0.03) Neonatal admission also high among teenagers (OR = 0.172, 95% CI = 0.08 - 0.39, PV = 0.001) compared to the babies of their adult counterpart. The rate of caesarean section and episiotomy was high among adult deliveries (21.7%). Conclusion: There is a high prevalence of teenage pregnancy (13.54%) in the Bamenda Health District. prematurity was independently associated with teenage pregnancy. perineal tears were the most common maternal outcome of teenage pregnancy. Adolescents/teenagers in rural areas, having a low level of income, and low level of education were associated with high level of teenage pregnancy.展开更多
基金supported by the National Natural Science Foundation of China (52307239,52102300,52207234)the Natural Science Foundation of Hubei Province (2022CFB1003,2021CFA025)。
文摘Due to its low cost and natural abundance of sodium,Na-ion batteries(NIBs)are promising candidates for large-scale energy storage systems.The development of ultralow voltage anode materials is of great significance in improving the energy density of NIBs.Low-voltage anode materials,however,are severely lacking in NIBs.Of all the reported insertion oxides anodes,the Na_(2)Ti_(3)O_(7) has the lowest operating voltage(an average potential of 0.3 V vs.Na^(+)/Na)and is less likely to deposit sodium,which has excellent potential for achieving NIBs with high energy densities and high safety.Although significant progress has been made,achieving Na_(2)Ti_(3)O_(7) electrodes with excellent performance remains a severe challenge.This paper systematically summarizes and discusses the physicochemical properties and synthesis methods of Na_(2)Ti_(3)O_(7).Then,the sodium storage mechanisms,key issues and challenges,and the optimization strategies for the electrochemical performance of Na_(2)Ti_(3)O_(7) are classified and further elaborated.Finally,remaining challenges and future research directions on the Na_(2)Ti_(3)O_(7) anode are highlighted.This review offers insights into the design of high-energy and high-safety NIBs.
文摘The generation of photovoltaic(PV)solar energy is increasing continuously because it is renewable,unlimited,and clean energy.In the past,generation systems depended on non-renewable sources such as oil,coal,and gas.Therefore,this paper assesses the performance of a 51 kW PV solar power plant connected to a low-voltage grid to feed an administrative building in the 6th of October City,Egypt.The performance analysis of the considered grid-connected PV system is carried out using power system simulator for Engineering(PSS/E)software.Where the PSS/E program,monitors and uses the power analyzer that displays the parameters and measures some parameters such as current,voltage,total power,power factor,frequency,and current and voltage harmonics,the used inverter from the type of grid inverter for the considered system.The results conclude that when the maximum solar radiation is reached,the maximum current can be obtained from the solar panels,thus obtaining the maximum power and power factor.Decreasing total voltage harmonic distortion,a current harmonic distortion within permissible limits using active harmonic distortion because this type is fast in processing up to 300 microseconds.The connection between solar stations and the national grid makes the system more efficient.
基金supported by the Science and Technology Support Program of Guizhou Province([2022]General 012)the Key Science and Technology Project of China Southern Power Grid Corporation(GZKJXM20220043)。
文摘The increasing proportion of distributed photovoltaics(DPVs)and electric vehicle charging stations in low-voltage distribution networks(LVDNs)has resulted in challenges such as distribution transformer overloads and voltage violations.To address these problems,we propose a coordinated planning method for flexible interconnections and energy storage systems(ESSs)to improve the accommodation capacity of DPVs.First,the power-transfer characteristics of flexible interconnection and ESSs are analyzed.The equipment costs of the voltage source converters(VSCs)and ESSs are also analyzed comprehensively,considering the differences in installation and maintenance costs for different installation locations.Second,a bilevel programming model is established to minimize the annual comprehensive cost and yearly total PV curtailment capacity.Within this framework,the upper-level model optimizes the installation locations and capacities of the VSCs and ESSs,whereas the lower-level model optimizes the operating power of the VSCs and ESSs.The proposed model is solved using a non-dominated sorting genetic algorithm with an elite strategy(NSGA-II).The effectiveness of the proposed planning method is validated through an actual LVDN scenario,which demonstrates its advantages in enhancing PV accommodation capacity.In addition,the economic benefits of various planning schemes with different flexible interconnection topologies and different PV grid-connected forms are quantitatively analyzed,demonstrating the adaptability of the proposed coordinated planning method.
基金supported by the National Natural Science Foundation of China (Grant No. 61904110)。
文摘A novel structure of low-voltage trigger silicon-controlled rectifiers(LVTSCRs) with low trigger voltage and high holding voltage is proposed for electrostatic discharge(ESD) protection. The proposed ESD protection device possesses an ESD implant and a floating structure. This improvement enhances the current discharge capability of the gate-grounded NMOS and weakens the current gain of the silicon-controlled rectifier current path. According to the simulation results, the proposed device retains a low trigger voltage characteristic of LVTSCRs and simultaneously increases the holding voltage to 5.53 V, providing an effective way to meet the ESD protection requirement of the 5 V CMOS process.
基金supported by the project of China Geological Survey(Grant No.DD20221677-2)the fundamental research funds of Chinese Academy of Geological Sciences Basal Research Fund(Grant No.JKYQN202307).
文摘Fluoride and nitrate enriched groundwater are potential threats to the safety of the groundwater supply that may cause significant effects on human health and public safety,especially in aggregated population areas and economic hubs.This study focuses on the high F^(−)and NO_(3)^(−)concentration groundwater in Tongzhou District,Beijing,North China.A total of 36 groundwater samples were collected to analyze the hydrochemical characteristics,elucidate genetic mechanisms and evaluate the potential human health risks.The results of the analysis indicate:Firstly,most of the groundwater samples are characterized by Mg-HCO_(3) and Na-HCO_(3) with the pH ranging from 7.19 to 8.28 and TDS with a large variation across the range 471-2337 mg/L.The NO_(3)^(−)concentration in 38.89%groundwater samples and the F^(−)concentration in 66.67%groundwater samples exceed the permissible limited value.Secondly,F^(−)in groundwater originates predominantly from water-rock interactions and the fluorite dissolution,which is also regulated by cation exchange,competitive adsorption of HCO_(3)−and an alkaline environment.Thirdly,the effect of sewage disposal and agricultural activities have a significant effect on high NO3-concentration,while the high F^(−)concentration is less influenced by anthropogenic activity.The alkaline environment favors nitrification,thus being conducive to the production of NO_(3)^(−).Finally,the health risk assessment is evaluated for different population groups.The results indicate that high NO_(3)^(−)and F^(−)concentration in groundwater would have the largest threat to children’s health.The findings of this study could contribute to the provision of a scientific basis for groundwater supply policy formulation relating to public health in Tongzhou District.
基金supported by the Shandong Province Natural Science Foundation Youth Branch(ZR2023QC157)the National Natural Science Foundation of China(51979233)+1 种基金the Key Research and Development Project of Shaanxi Province(2022KW-47,2022NY-220)the Heze University Doctoral Research Fund(XY21BS24,XY22BS17).
文摘Drip irrigation and flood irrigation are major irrigation methods for maize crops in the Hetao Irrigation District,Inner Mongolia Autonomous Region,China.This research delves into the effects of these irrigation methods on carbon dioxide(CO_(2))exchange and crop growth in this region.The experimental site was divided into drip and flood irrigation zones.The irrigation schedules of this study aligned with the local commonly used irrigation schedule.We employed a developed chamber system to measure the diurnal CO_(2)exchange of maize plants during various growth stages under both drip and flood irrigation methods.From May to September in 2020 and 2021,two sets of repeated experiments were conducted.In each experiment,a total of nine measurements of CO_(2)exchange were performed to obtain carbon exchange data at different growth stages of maize crop.During each CO_(2)exchange measurement event,CO_(2)flux data were collected every two hours over a day-long period to capture the diurnal variations in CO_(2)exchange.During each CO_(2)exchange measurement event,the biological parameters(aboveground biomass and crop growth rate)of maize and environmental parameters(including air humidity,air temperature,precipitation,soil water content,and photosynthetically active radiation)were measured.The results indicated a V-shaped trend in net ecosystem CO_(2)exchange in daytime,reducing slowly at night,while the net assimilation rate(net primary productivity)exhibited a contrasting trend.Notably,compared with flood irrigation,drip irrigation demonstrated significantly higher average daily soil CO_(2)emission and greater average daily CO_(2)absorption by maize plants.Consequently,within the maize ecosystem,drip irrigation appeared more conducive to absorbing atmospheric CO_(2).Furthermore,drip irrigation demonstrated a faster crop growth rate and increased aboveground biomass compared with flood irrigation.A strong linear relationship existed between leaf area index and light utilization efficiency,irrespective of the irrigation method.Notably,drip irrigation displayed superior light use efficiency compared with flood irrigation.The final yield results corroborated these findings,indicating that drip irrigation yielded higher harvest index and overall yield than flood irrigation.The results of this study provide a basis for the selection of optimal irrigation methods commonly used in the Hetao Irrigation District.This research also serves as a reference for future irrigation studies that consider measurements of both carbon emissions and yield simultaneously.
文摘In the economic development of Beijing,although the share of the total amount of agricultural industry in the overall economy is relatively low,it has an important impact on the daily life of residents,social stability and the development of other industries.Changping District,as an important agricultural production base of Beijing,its agricultural development has an indispensable strategic significance for the stability and growth of the entire regional economy.Therefore,it is very important to study the structure of agricultural industry in Changping District.Based on the detailed analysis of the agricultural industrial structure of Changping District,this paper uses the grey relation theory to analyze the different industries in the agricultural industrial structure of Changping District,including planting,forestry,animal husbandry,fishery and agricultural,forestry,service industries,in order to reveal the impact of these industries on the agricultural industrial structure of Changping District.Through this study,it comes up with specific and feasible suggestions for the optimization of agricultural industrial structure in Changping District,and provides valuable reference for the agricultural development of other areas in Beijing.
文摘With the rapid development of urban economy, distribution network construction of city is lagging behind the increment of load, and low-voltage problem has become the main complaints of the power users. Based on Python [1] scripting language, this paper develops a piece of software which can provide a friendly human-machine experience for the user, calculate the voltage of the power distribution area and propose corresponding control measures, then the paper takes the actual power distribution area to verify its effectiveness.
文摘Scaling problems and limitations of conventional silicon transistors have led the designers to exploit novel nano-technologies. One of the most promising and feasible nano-technologies is CNT(Carbon Nanotube) based transistors. In this paper, a high-speed and energy-efficient CNFET(Carbon Nanotube Field Effect Transistor) based Full Adder cell is proposed for nanotechnology. This design is simulated in various supply voltages, frequencies and load capacitors using HSPICE circuit simulator. Significant improvement is achieved in terms of speed and PDP(Power-Delay-Product) in comparison with other classical and state-of-the-art CMOS and CNFET-based designs, existing in the literature. The proposed Full Adder can also drive large load capacitance and works properly in low supply voltages.
文摘Powder metallurgy is an efficient approach to fabricate varieties of high performance structure materials, function materials and special materials working under limited conditions. Research and development of new efficient technology to form high-density, high-performance and net shape parts is a key to widen application and development of powder materials. Recently, the low-voltage electromagnetic compaction (EMC) has been used by present authors to compacted copper, tin, aluminum powders and the products with 99% relative density have been acquired. In this work, the research has been extended to investigation on the density uniformity of pressed parts. The analysis results show that the density of the part compacted by low-voltage EMC decreases gradually in press direction as static compaction. But it is higher and more homogeneous. The density of the top part increases gradually from the center to the outer, which is just reversal of the bottom part. In some extent, the higher the discharging voltage is, the higher the density is and the more homogeneous the distribution is. In addition, repetitive compaction can improve the density of powder parts and the distribution uniformity.
基金the National Natural Science Foundation of China(No.50375114)State Key Laboratory of Plastic Forming Simulation and Die & Mould Technology(No.05-03)
文摘Low-voltage electromagnetic compaction (EMC) was used to compact metal powders (Cu) and ceramic powders (TiO2) in the indirect way. It was found that the density of the metal powder parts compacted by low-voltage EMC varied linearly with the discharging voltage in the range investigated. But for ceramic powders, the discharging voltage has an optimal value. Under the value, the density increases as discharging voltage rises, but beyond the value the trend is reverse. The experimental results show that the density of the metal parts decreases gradually along press direction. And the density of the ceramic parts decreases with the advancement of the aspect ratio h/d (height/diameter). In addition, repetitive compaction can improve the density of both metal and ceramic parts and reduce the effects of aspect ratio on the density.
基金The project supported by National Natural Science Foundation of China (No. 50477025)
文摘This paper is devoted to the simulation of the arc plasma in a simplified low-voltage circuit breaker chamber. Based on a group of coupled governing equations, a three-dimensional (3-D) arc plasma model is built and solved by a modified commercial code. Firstly, this paper presents a solution of the stationary state of the arc plasma and discusses the distribution of some parameters throughout the chamber. Secondly, with the ferromagnetic materials included, the balance of the stationary state is broken and a transient course is calculated. In light of the simulation results, the temperature distribution sequence, the arc motion and the plasma jet are then described and analyzed in detail.
文摘Low-voltage distribution systems in our country are mostly used in agricultural loads and household loads. The value and using time of these kinds of loads are uncontrollable, which lead to the three-phase imbalance in low-voltage distribution system, and seriously affect the quality of power supply. A new type of the commutation system and an improved quantum genetic algorithm (IQGA) are proposed in the paper. At last, the rationality and the efficiency of the method are verified by a practical example.
基金the Science & Technology research key project of MOE (No.10518)National Natural Science Foundation of China (Nos.50477025,50537050 and 50525722)
文摘This paper focuses on the simulation of the low-voltage arc with an opening contact. A controllable experiment setup with a rotating contact is designed to investigate the arc behaviour. Supported by the experiment, the phenomena of arc elongation and commutation in the case of rotating contact are simulated with the dynamic grid technique introduced. Under the given condition of the external magnetic field and the contact rotating velocity, the stagnation and rapid jump of two arc roots are observed by the calculated and experimental arc root displacement. The voltage of arc column can be divided into four phases and its sharp rising progress comes from the increase of the displacement difference between two arc roots in x direction.
文摘The low-voltage-electromagnetic forming was applied to powder compaction.A series of experiments was performed to compact aluminum,copper and tin powders in an indirect working way.Having compacted high-density powder parts successfully,the authors analyzed the effects of voltage,capacitance,friction,compaction times,powder size and other factors on the densities of compacted specimens.The experimental results show that lower voltage but larger capacitance are beneficial to increasing the density and homogeneity of the compacted specimens,if the loading velocity and discharging energy are suitable.The higher the voltage,the greater the percentage of energy consumed by friction.If the equipment energy is limited,the iterative compaction is an efficient way to manufacture homogeneous and high-density powder parts.
基金supported by the National Natural Science Foundation of China(Grant Nos.11175034,11335004,and 11405019)the Important National Science and Technology Specific Project of China(Grant No.2011 ZX 02403-001)
文摘Planar radio frequency inductively coupled plasmas(ICP) are employed for low-voltage ion implantation processes,with capacitive pulse biasing of the substrate for modulation of the ion energy. In this work, a two-dimensional(2D) selfconsistent fluid model has been employed to investigate the influence of the pulsed bias power on the nitrogen plasmas for various bias voltages and pulse frequencies. The results indicate that the plasma density as well as the inductive power density increase significantly when the bias voltage varies from 0 V to-4000 V, due to the heating of the capacitive field caused by the bias power. The N+fraction increases rapidly to a maximum at the beginning of the power-on time, and then it decreases and reaches the steady state at the end of the glow period. Moreover, it increases with the bias voltage during the power-on time, whereas the N2-+ fraction exhibits a reverse behavior. When the pulse frequency increases to 25 kHz and40 kHz, the plasma steady state cannot be obtained, and a rapid decrease of the ion density at the substrate surface at the beginning of the glow period is observed.
文摘In order to assess public effective dose due to gross alpha and beta in water, 43 tap water samples were collected from different areas in the District of Abidjan. Using the low background Gas-less Automatic Alpha/Beta counting system (Canberra iMatic<sup>TM</sup>) for analysis, the gross alpha and beta concentrations found varied from 0.001 ± 0.002 to 0.063 ± 0.050 Bq/l with an average of 0.013 ± 0.012 Bq/l and from 0.067 ± 0.080 to 0.320 ± 0.120 Bq/l with an average of 0.174 ± 0.076 Bq/l, respectively in samples. The public effective dose assessment showed values of dose to ingestion of alpha and beta emitter radionuclides lower than the recommended value of dose for drinking water 0.1 mSv/y, except in 30% of the samples. These results show the need for additional studies to be conducted in order to clarify the hazardousness of these water samples. However, this study still remains important because it has provided necessary data for future tap water quality monitoring studies in the District of Abidjan.
文摘Background: 25% of all people requiring surgical care are not able to access it due to its high cost. These people stand a high risk of preventable severe morbidity and mortality due to poor prognosis of surgically correctable illnesses. Ambulatory surgical care services are significantly cheaper than orthodox surgical care and have become very relevant in this time and age where health conditions that can only be treated with surgical intervention are on the rise. The acceptability of ambulatory surgical care services will determine how this model increases universal health coverage. Objective: To assess the acceptability of ambulatory surgical services and its predictors among residents of Budondo Sub-County—Jinja district. Methods: The study was cross-sectional targeting 371 household heads in Budondo Sub-County, which was stratified by parish, with villages in each randomly sampled. Systematic random sampling was used to sample households and households therein were purposively sampled. Structured interviews and questionnaires were the data collection techniques, and data was analyzed in SPSS version 25 using descriptive statistics and a binomial logit model. Results: The level of acceptability of ambulatory surgical care services among residents of Budondo Sub-County was found to be near-universal, at 96.5%. The odds of accepting ambulatory surgical care were least among household heads who agreed that surgery done in a hospital would be cheaper than surgery done at community level (aOR = 0.174 [CI = 0.055 - 0.553]), those who had health insurance (aOR = 0.105 [95% CI = 0.030 - 0.371]), and household heads who were covered with private health insurance (aOR = 0.078 [95% CI = 0.008 - 0.792]). Acceptability of ASC was higher among household heads who agreed that they would trust ambulatory surgical centers with their life were more likely to accept ambulatory surgical care (aOR = 1.124, [95% CI = 1.122 - 3.218], P = 0.000), and household heads from households that had less than five members with surgery history were twice as likely to accept ambulatory surgical care (aOR = 2.431 [95% CI = 1.122 - 5.898], P = 0.000). Conclusion: Acceptability of ambulatory surgical care services among residents of Budondo Sub-County is high, and near-universal. It is mainly predicted by intrapersonal correlates and to a small extent by socio-demographic characteristics, with the implication that the administration of Global Surgical Initiatives in Kyabirwa ought to focus on modifying or uphold the intrapersonal characteristics found to be antagonists and protagonists of acceptability, respectively.
文摘Labour-saving or mechanization technologies have become the driving force behind modern agriculture, yet adoption of these technologies remains low in many parts of the developing world, particularly among female farmers in Ghana. This study aims to investigate the factors that hinder the adoption of agricultural mechanization technologies by female farmers in the Karaga District of the Northern Region of Ghana. This region is known for its large agricultural lands and significant role in commercial farming. The research was conducted using qualitative research methodology and involved interviewing 60 female farmers using an interview guide. The principle of sample saturation was used, meaning that further interviews were deemed unnecessary after the 60th interview. The results showed that low adoption of agricultural mechanization technologies is due to poor access to commercial lands, gender biases, lack of access to credit, and poor awareness about the benefits of these technologies. In conclusion, the low adoption of agricultural mechanization technologies is preventing women farmers in the Karaga District and elsewhere in Ghana from fully participating in commercial agricultural production. It is recommended that gender biases and cultural stereotypes be addressed to improve women farmers’ access to lands and credit, which will facilitate the adoption of mechanization technologies and lead to improved agricultural production.
文摘Teenage pregnancy is a common public health problem worldwide because teenagers in general are ill-prepared to deal with the burden of pregnancy. Sub-Saharan Africa has the highest burden of teenage pregnancy precisely in the west and central Africa;in Cameroon, about 12% of all births are to teenage mothers. Complications from pregnancy and childbirth are the leading cause of death among girls aged 15 to 19. Though the trend of teenage pregnancy tends to decrease in most parts of the world, this is not the case in our setting. The main aim of this study was to determine the prevalence, outcomes and the associated factors of teenage pregnancy in the Bamenda Health District (BHD). Materials and Method: This was a hospital-based cross-sectional descriptive and analytic study carried out at the maternity and postnatal units of the Bamenda Regional Hospital and the Nkwen Medicalised Health Center. A consecutive non-probabilistic sampling technique was used to recruit participants. A pretested questionnaire was used to collect information from the participant. Data was analysed using the software SPSS version 23. Bivariate logistic regression was used to test for associations. Statistical significance was set at p-value less than 0.05. Result: A total of 325 participants were recruited of which 44 were teenagers. The mean age of the participants was 25.02 ± 0.257 years. The mean age of teenagers was 17.49 ± 0.63 years, and mean adult age was 28.43 ± 5.64 years. The youngest participant was 15 years. Teenagers were significantly more likely to prematurity (OR = 0.14;95% CI = 0.06 - 0.31;PV = 0.001), Low birth weight among teenagers (OR = 0.077;95% CI = 0.03 - 0.21;PV = 0.001), Still birth;OR = 0.07;95% CI = 0.01 - 0.86;PV = 0.03) Neonatal admission also high among teenagers (OR = 0.172, 95% CI = 0.08 - 0.39, PV = 0.001) compared to the babies of their adult counterpart. The rate of caesarean section and episiotomy was high among adult deliveries (21.7%). Conclusion: There is a high prevalence of teenage pregnancy (13.54%) in the Bamenda Health District. prematurity was independently associated with teenage pregnancy. perineal tears were the most common maternal outcome of teenage pregnancy. Adolescents/teenagers in rural areas, having a low level of income, and low level of education were associated with high level of teenage pregnancy.