A novel transient rotor current control scheme of a doubly-fed induction generator equipped with superconducting magnetic energy storage for voltage and frequency support

A novel transient rotor current control scheme is proposed in this paper for a doubly-fed induction generator（DFIG）equipped with a superconducting magnetic energy storage（SMES） device to enhance its transient voltage and frequency support capacity during grid faults. The SMES connected to the DC-link capacitor of the DFIG is controlled to regulate the transient dc-link voltage so that the whole capacity of the grid side converter（GSC） is dedicated to injecting reactive power to the grid for the transient voltage support. However, the rotor-side converter（RSC） has different control tasks for different periods of the grid fault. Firstly, for Period I, the RSC injects the demagnetizing current to ensure the controllability of the rotor voltage. Then, since the dc stator flux degenerates rapidly in Period II, the required demagnetizing current is low in Period II and the RSC uses the spare capacity to additionally generate the reactive（priority） and active current so that the transient voltage capability is corroborated and the DFIG also positively responds to the system frequency dynamic at the earliest time. Finally, a small amount of demagnetizing current is provided after the fault clearance. Most of the RSC capacity is used to inject the active current to further support the frequency recovery of the system. Simulations are carried out on a simple power system with a wind farm. Comparisons with other commonly used control methods are performed to validate the proposed control method.

High magnetic energy product in isotropic nanocomposite powders with high percent of soft phase towards ultrastrong magnets

Nanostructure of magnetically hard and soft materials is fascinating for exploring next-generation ul-trastrong permanent magnets with less expensive rare-earth elements.However,the resulting hard/soft nanocomposites often exhibit a low remanence/energy product due to the challenge in obtaining ideal phase components and appropriate soft phase fraction.In this work,a novel microstructure of multiple phases consisting of 1:5 phase and 1:3 phase as main hard phase,and a high ratio of Fe(Co)(27 wt.%-48 wt.%)as soft phase was obtained in Sm-Co(Fe)/Fe nanocomposite magnet.The grain size of both hard and soft phases below 15 nm was observed.The optimal energy product for Sm-Co(Fe)/Fe(Co)nanocom-posite is 2.1 times(an increment of 107%)of the corresponding single-hard-phase powders without soft phase.It reports that the isotropic nanocomposite powders exhibit a record of magnetic energy product larger than 25 MGOe(the highest value is 28.6 MGOe).The high performance and the microstructure achieved in this work for the isotropic powders will shed light on and provide a good premise for syn-thesizing high performance anisotropic bulk nanocomposite magnets.

Superconducting Magnetic Energy Storage Integrated Current-source DC/DC Converter for Voltage Stabilization and Power Regulation in DFIG-based DC Power Systems

Unpredictable power fluctuation and fault ridethrough capability attract increased attention as two uncertain major factors in doubly-fed induction generators(DFIGs)integrated DC power system.Present solutions usually require complicated cooperation comprising multiple modules of energy storage,current control,and voltage stabilizer.To overcome the drawbacks of existing solutions,this paper proposes a superconducting magnetic energy storage(SMES)integrated currentsource DC/DC converter(CSDC).It is mainly composed of a current-source back-to-back converter,and the SMES is tactfully embedded in series with the intermediate DC link.The proposed SMES-CSDC is installed in front of the DC-DFIG to carry out its dual abilities of load voltage stabilization under multifarious transient disturbances and power regulation under wind speed variations.Compared with the existing DC protection devices,the SMES-CSDC is designed on the basis of unique current-type energy storage.It has the advantages of fast response,extensive compensation range,concise hardware structure,and straightforward control strategy.The feasibility of the SMESCSDC is implemented via a scaled-down experiment,and its effectiveness for DC-DFIG protection is verified by a large-scale DC power system simulation.

Intelligent Fractional-Order Controller for SMES Systems in Renewable Energy-Based Microgrid

An autonomous microgrid that runs on renewable energy sources is presented in this article.It has a supercon-ducting magnetic energy storage(SMES)device,wind energy-producing devices,and an energy storage battery.However,because such microgrids are nonlinear and the energy they create varies with time,controlling and managing the energy inside them is a difficult issue.Fractional-order proportional integral(FOPI)controller is recommended for the current research to enhance a standalone microgrid’s energy management and performance.The suggested dedicated control for the SMES comprises two loops:the outer loop,which uses the FOPI to regulate the DC-link voltage,and the inner loop,responsible for regulating the SMES current,is constructed using the intelligent FOPI(iFOPI).The FOPI+iFOPI parameters are best developed using the dandelion optimizer(DO)approach to achieve the optimum performance.The suggested FOPI+iFOPI controller’s performance is contrasted with a conventional PI controller for variations in wind speed and microgrid load.The optimal FOPI+iFOPI controller manages the voltage and frequency of the load.The behavior of the microgrid as a reaction to step changes in load and wind speed was measured using the proposed controller.MATLAB simulations were used to evaluate the recommended system’s performance.The results of the simulations showed that throughout all interruptions,the recommended microgrid provided the load with AC power with a constant amplitude and frequency.In addition,the required load demand was accurately reduced.Furthermore,the microgrid functioned incredibly well despite SMES and varying wind speeds.Results obtained under identical conditions were compared with and without the best FOPI+iFOPI controller.When utilizing the optimal FOPI+iFOPI controller with SMES,it was found that the microgrid performed better than the microgrid without SMES.

Room temperature quantum anomalous Hall insulator in honeycomb lattice, RuCS_(3), with large magnetic anisotropy energy

The quantum anomalous Hall(QAH) effect has attracted enormous attention since it can induce topologically protected conducting edge states in an intrinsic insulating material. For practical quantum applications, the main obstacle is the non-existent room temperature QAH systems, especially with both large topological band gap and robust ferromagnetic order. Here, according to first-principles calculations, we predict the realization of the room temperature QAH effect in a two-dimensional(2D) honeycomb lattice, RuCS_(3) with a non-zero Chern number of C = 1. Especially, the nontrivial topology band gap reaches up to 336 me V for RuCS_(3). Moreover, we find that RuCS_(3) has a large magnetic anisotropy energy(2.065 me V) and high Curie temperature(696 K). We further find that the non-trivial topological properties are robust against the biaxial strain. The robust topological and magnetic properties make RuCS_(3) have great applications in room temperature spintronics and nanoelectronics.

Energy-saving Superconducting Magnetic Energy Storage(SMES)Based Interline DC Dynamic Voltage Restorer

The fast-response feature from a superconducting magnetic energy storage(SMES)device is favored for suppressing instantaneous voltage and power fluctuations,but the SMES coil is much more expensive than a conventional battery energy storage device.In order to improve the energy utilization rate and reduce the energy storage cost under multiple-line power distribution conditions,this paper investigates a new interline DC dynamic voltage restorer(IDC-DVR)scheme with one SMES coil shared among multiple compensating circuits.In this new concept,an improved current-voltage(I/V)chopper assembly,which has a series of input/output power ports,is introduced to connect the single SMES coil with multiple power lines,and thereby satisfy the independent energy exchange requirements of any line to be compensated.Specifically,if two or more power lines have simultaneous compensating demands,the SMES coil can be selectively controlled to compensate the preferable line according to the priority order of the line.The feasibility of the proposed scheme is technically verified to maintain the transient voltage stability in multiple-line voltage swell and sag cases caused by either output voltage fluctuations from external power sources or power demand fluctuations from local sensitive loads.The simulation results provide a technical basis to develop a cost-effective SMES-based IDC-DVR for use in various DC distribution networks.

Generation of Alfvén wave energy during magnetic reconnection in Hall MHD

The effect of the reconnection rate on the generation of Alfvén wave energy is systematically investigated using Hall magnetohydrodynamics（MHD）. It is well known that a decrease in magnetic energy is proportional to the reconnection rate. It is found that an instantaneous increase in Alfvén wave energy in unit Alfvén time is the square dependence on the reconnection rate. The converted Alfvén wave energy is strongly enhanced due to the large increase in the reconnection rate in Hall MHD. For solar-terrestrial plasmas, the maximum converted Alfvén wave energy in unit Alfvén time with the Hall effect can be over 50 times higher than that without the Hall effect during magnetic reconnection.

A Self-consistent Calculation and an Anisotropic Wavelength Cut off Energy of Spin-wave Spectrumin Magnetic Tunnel Junctions

Temperature dependence of tunnel magnetoresistance (TMR) ratio. resistance, and coercivity from 4.2 K to room temperature (RT), applied dc bias voltage dependence of the TMR ratio and resistances at 4.2 K and RT. tunnel current I and dynamic conductance dI/dV as functions of the dc bias voltage at 4.2 K, and inelastic electron tunneling (IET) spectroscopy, d2I/dV2 versus V, at 4.2 K for a tunnel junction of Ta(5 nm)/Ni79 Fe21 (25 nm)/lr22 Mn78(12 nm)/Co75 Fe25(4 nm)/ Al(0.8 um)-oxide/Co75Fe25(4 nm)/Ni79Fe21(25 nm)/Ta(5 um ) were systematically investigated High TMR ratio of 59.2% at 4.2 K and 41.3% at RT were observed for this junction after annealing at 275’C for an hour. The temperature dependence of TMR ratio and resistances from 4.2 to 300 K at 1.0 mV bias and the dc bias voltage dependence of TMR ratio at 4.2 K from 0 to 80 mV can be evaluated by a comparison of self-consistent calculations with the experimental data based on the magnon-assisted inelastic excitation model and theory. An anisotropic wavelength cutoff energy of spin-wave spectrum in magnetic tunnel junctions (MTJs) was suggested, which is necessary for self-consistent calculations, based on a series of IET spectra observed in the MTJs.

Evolution of structure and magnetic properties in PrCo_5 magnet for high energy ball milling in ethanol

High energy ball milling(HEBM) is employed to produce nano-sized grains and particles. In this paper, the structure and magnetic properties are investigated in PrCo5 alloy for HEBM in an ethanol milling medium. With the increase of milling time, the grain size reduces and the coercivity increases. For a milling time of less than 30 min, the hysteresis loop of the aligned sample is very different from that of the un-aligned sample and it does not show a large decrease in magnetization slope, indicating a relatively good alignment of easy axes in particles due to the fact that the texture is nearly well preserved. However, when the milling time is further prolonged, the textured structure deteriorates in the powders.Even though exchange coupling exists between grains within the particle, the magnetic properties are exchange-decoupled between particles and the dipolar interaction results in a negative value of δ m in the whole range of the magnetic field.

The Circular Current Loop as a Model of Fundamental Particles

The presented circular current loop model reveals that charged fundamental particles such as the electron consist essentially of electric and magnetic energy. The magnetic properties have the same order of magnitude as the electric ones. The electromagnetic field energy is the origin of the inertial mass. The Higgs boson, existing or not, is not needed to “explain” particle mass. The magnetic moment of fundamental particles is not anomalous! The “anomaly” indicates the existence of a small additional amount of kinetic energy. Thus, fundamental particles are not purely field-like such as photons and not (essentially) mass-like such as atoms, they represent a special kind of matter in between. Their kinetic energy is obviously not due to any relativistic effect but is related to an independent physical law that provides, together with the magnetic energy, the angular momentum exactly to be ħ/2. Fundamental particles are (at least) two-dimensional. In the simplest case their core consists of two concentric, nearly identical current loops. Their relative design details, the “anomaly” factor, and the rotational velocity of the uniformly distributed elementary charge follow from the stability condition, i.e. electric and magnetic force balance, and do not depend on the particle’s rest mass! Fundamental particles are objects of classical physics. Their magnetic forces are the true origin of the weak and strong nuclear interactions. For their explanation bosons and gluons are not needed.

Controllable high Curie temperature through 5d transition metal atom doping in CrI_(3)

Two-dimensional(2D) CrI_(3) is a ferromagnetic semiconductor with potential for applications in spintronics. However,its low Curie temperature(T_(c)) hinders realistic applications of CrI3. Based on first-principles calculations, 5d transition metal(TM) atom doping of CrI_(3)(TM@CrI_(3)) is a universally effective way to increase T_(c), which stems from the increased magnetic moment induced by doping with TM atoms. T_(c) of W@CrI_(3) reaches 254 K, nearly six times higher than that of the host CrI_(3). When the doping concentration of W atoms is increased to above 5.9%, W@CrI_(3) shows room-temperature ferromagnetism. Intriguingly, the large magnetic anisotropy energy of W@CrI_(3) can stabilize the long-range ferromagnetic order. Moreover, TM@CrI_(3) has a strong ferromagnetic stability. All TM@CrI_(3) change from a semiconductor to a halfmetal, except doping with Au atom. These results provide information relevant to potential applications of CrI_(3) monolayers in spintronics.

Electronic property and topological phase transition in a graphene/CoBr_(2) heterostructure

Recently,significant experimental advancements in achieving topological phases have been reported in van der Waals(vdW)heterostructures involving graphene.Here,using first-principles calculations,we investigate graphene/CoBr_(2)(Gr/CoBr_(2))heterostructures and find that an enhancement of in-plane magnetic anisotropy(IMA)energy in monolayer CoBr_(2) can be accomplished by reducing the interlayer distance of the vdW heterostructures.In addition,we clarify that the enhancement of IMA energy primarily results from two factors:one is the weakness of the Co-d_(xy) and Co-d_(x^(2)-y^(2)) orbital hybridization and the other is the augmentation of the Co-d_(yz) and Co-d_(z)2 orbital hybridization.Meanwhile,calculation results suggest that the Kosterlitz–Thouless phase transition temperature(TKT)of a 2D XY magnet Gr/CoBr_(2)(23.8 K)is higher than that of a 2D XY monolayer CoBr_(2)(1.35 K).By decreasing the interlayer distances,the proximity effect is more pronounced and band splitting appears.Moreover,by taking into account spin–orbit coupling,a band gap of approximately 14.3 meV and the quantum anomalous Hall effect(QAHE)are attained by decreasing the interlayer distance by 1.0 A.Inspired by the above conclusions,we design a topological field transistor device model.Our results support that the vdW interlayer distance can be used to modulate the IMA energy and QAHE of materials,providing a pathway for the development of new low-power spintronic devices.

DEPENDENCE OF MAGNETISM OF Nd-Fe-B SINTERMAGNETS ON ORIENTATION MAGNETIC FIELD

The effect of the orientation magnetic field on the permanent magnetism of Nd-Fe-B sintermagnets is investigated. The results show that the variation law of magnetism with orientation field obviously changes at the critical orientation field and the intensity of the orientation field should he determined by the dimension ratio of the magnet for effectively utilizing its magnetic energy product.

High Index SMES Device for Gravitomagnetic Field Generation

A method is described for creating a measurable unbalanced gravitational acceleration using a gravitomagnetic field surrounding a superconducting toroid as described by Forward (1962). An experimental Superconducting Magnetic Energy Storage (SMES) toroid configuration of wound superconducting nanowire is proposed to create a measurable acceleration field along the axis of symmetry, providing experimental confirmation of the additive nature of a Lense-Thirring derived gravitomagnetic field. In the present paper, gravitational coupling enhancement of this effect is explored using a high index or high permittivity material, as predicted by Sarfatti (2020) using his modification to Einstein’s General Relativity Field Equations for gravitational coupling in matter.

High Energy and High Coercivity Sintered NdFeB Magnets by Low Oxygen Process

Using ball milling and single direction pressing, we can produce high performance NdFeB sintered magnets. The oxygen content of sintered magnets can be controlled under 1500xl0^-6 and the magnetic performance can be improved by using low oxygen processing. The high preformance NdFeB sintered magnets with Br=(1.4 ± 0.2)T, iHc>796 kA/m and (BH)max=(390± 16) kJ/m^3, have been batch produced.

Magnetic tuning in a novel half-metallic Ir_(2)TeI_(2) monolayer

A two-dimensional(2D) high-temperature ferromagnetic half-metal whose magnetic and electronic properties can be flexibly tuned is required for the application of new spintronics devices. In this paper, we predict a stable Ir_(2)TeI_(2) monolayer with half-metallicity by systematical first-principles calculations. Its ground state is found to exhibit inherent ferromagnetism and strong out-of-plane magnetic anisotropy of up to 1.024 meV per unit cell. The Curie temperature is estimated to be 293 K based on Monte Carlo simulation. Interestingly, a switch of magnetic axis between in-plane and out-of-plane is achievable under hole and electron doping, which allows for the effective control of spin injection/detection in such 2D systems. Furthermore, the employment of biaxial strain can realize the transition between ferromagnetic and antiferromagnetic states. These findings not only broaden the scope of 2D half-metal materials but they also provide an ideal platform for future applications of multifunctional spintronic devices.

Magnetpolaron effect in two-dimensional anisotropic parabolic quantum dot in a perpendicular magnetic field

We study the two-dimensional weak-coupling Frohlich polaron in a completely anisotropic quantum dot in a perpendicular magnetic field. By performing a unitary transformation, we first transform the Hamiltonian into a new one which describes an anisotropic harmonic oscillator with new mass and trapping frequencies interacting with the same phonon bath but with different interaction form and strength. Then employing the second-order Rayleigh–Schrodinger perturbation theory, we obtain the polaron correction to the ground-state energy. The magnetic field and anisotropic effects on the polaron correction to the ground-state energy are discussed.

STUDIES ON PROCESS AND STABILITY OF BONDED Sm_2TM_(17)MAGNETS WITH HIGH COERCIVITY AND HIGH ENERGY PRODUCT

The process of the epoxy-bonded Sm_2TM_(17) magnets includes:(1)after melting,the ingots are treated by solid soluiion,and then aged and pulverized;(2)the obtained alloy powder is mixed with epoxy resin bind- er;(3)the mixture is pressed in a magnetic field;(4)the compacts are cured.When the SmCo_(4.9)Fe_(2.7)Cu_(0.54)Zr_(0.13) alloy is heat treated and pressed with optimum pressing parameters,the high quality bonded magnets with B_r=8250 G,_iH_c=13000 Oe,and(BH)_(max)=16MGOe can be obtained.The stability of the magnets is studied also.The irreversible loss of O.C.(open circuit)remanence B_r in the temperature range between 25 and 150℃,is less than 4%.The average temperature coefficient at temperatures between 25 and 70℃ is-0.03%/℃.The magnets obtained have heat resistance up to 130℃ even in long-term service, and have good corrosion resistance in acid,alkali and salt solutions.

An Advanced FMRL Controller for FACTS Devices to Enhance Dynamic Performance of Power Systems

The parameters of power system slowly change with time due to environmental effects or may change rapidly due to faults. It is preferable that the control technique in this system possesses robustness for various fault conditions and disturbances. The used flexible alternating current transmission system （FACTS） in this paper is an advanced super-conducting magnetic energy storage （ASMES）. Many control techniques that use ASMES to improve power system stability have been proposed. While fuzzy controller has proven its value in some applications, the researches applying fuzzy controller with ASMES have been actively reported. However, it is sometimes very difficult to specify the rule base for some plants, when the parameters change. To solve this problem, a fuzzy model reference learning controller （FMRLC） is proposed in this paper, which investigates multi-input multi-output FMRLC for time-variant nonlinear system. This control method provides the motivation for adaptive fuzzy control, where the focus is on the automatic online synthesis and tuning of fuzzy controller parameters （i.e., using online data to continually learn the fuzzy controller that will ensure that the performance objectives are met）. Simulation results show that the proposed robust controller is able to work with nonlinear and nonstationary power system （i.e., single machine-infinite bus （SMIB） system）, under various fault conditions and disturbances.