基于Damper的方向盘抖动问题优化设计

方向盘是顾客使用频次较高的零部件,受发动机等振源影响,在某些工况下方向盘会出现抖动等让顾客感到不适的问题,本文浅析了某车型方向盘高速抖动的原因,在现有方向盘结构上优化设计,增加Damper吸振器,有效解决了方向盘抖动问题,提升了顾客舒适性。

Seismic control of multi-degrees-of-freedom structures by vertical mass isolation method using MR dampers

Vertical mass isolation(VMI)is one of the novel methods for the seismic control of structures.In this method,the entire structure is assumed to consist of two mass and stiffness subsystems,and an isolated layer is located among them.In this study,the magnetorheological damper in three modes:passive-off,passive-on,and semi-active mode with variable voltage between zero and 9 volts was used as an isolated layer between two subsystems.Multi-degrees-of-freedom structures with 5,10,and 15 floors in two dimensions were examined under 11 pairs of near field earthquakes.On each level,the displacement of MR dampers was taken into account.The responses of maximum displacement,maximum inter-story drift,and maximum base shear in controlled and uncontrolled buildings were compared to assess the suggested approach for seismic control of the structures.According to the results,the semi-active control method can reduce the response by more than 12%compared to the uncontrolled mode in terms of maximum displacement of the mass subsystem of the structures.This method can reduce more than 16%and 20%of the responses compared to the uncontrolled mode in terms of maximum inter-story drift and base shear of the structure,respectively.

Theoretical and Experimental Study on the Performance of Hermetic Diaphragm Squeeze Film Dampers for Gas-Lubricated Bearings

Low damping characteristics have always been a key sticking points in the development of gas bearings.The application of squeeze film dampers can significantly improve the damping performance of gas lubricated bearings.This paper proposed a novel hermetic diaphragm squeeze film damper(HDSFD)for oil-free turbomachinery supported by gas lubricated bearings.Several types of HDSFDs with symmetrical structure were proposed for good damping performance.By considering the compressibility of the damper fluid,based on hydraulic fluid mechanics theory,a dynamic model of HDSFDs under medium is proposed,which successfully reflects the frequency dependence of force coefficients.Based on the dynamic model,the effects of damper fluid viscosity,bulk modulus of damper fluid,thickness of damper fluid film and plunger thickness on the dynamic stiffness and damping of HDSFDs were analyzed.An experimental test rig was assembled and series of experimental studies on HDSFDs were conducted.The damper fluid transverse flow is added to the existing HDSFD concept,which aims to make the dynamic force coefficients independent of frequency.Although the force coefficient is still frequency dependent,the damping coefficient at high frequency excitation with damper fluid supply twice as that without damper fluid supply.The results serve as a benchmark for the calibration of analytical tools under development.

Vibration attenuation performance of wind turbine tower using a prestressed tuned mass damper under seismic excitation

With the rapid development of large megawatt wind turbines,the operation environment of wind turbine towers(WTTs)has become increasingly complex.In particular,seismic excitation can create a resonance response and cause excessive vibration of the WTT.To investigate the vibration attenuation performance of the WTT under seismic excitations,a novel passive vibration control device,called a prestressed tuned mass damper(PS-TMD),is presented in this study.First,a mathematical model is established based on structural dynamics under seismic excitation.Then,the mathematical analytical expression of the dynamic coefficient is deduced,and the parameter design method is obtained by system tuning optimization.Next,based on a theoretical analysis and parameter design,the numerical results showed that the PS-TMD was able to effectively mitigate the resonance under the harmonic basal acceleration.Finally,the time-history analysis method is used to verify the effectiveness of the traditional pendulum tuned mass damper(PTMD)and the novel PS-TMD device,and the results indicate that the vibration attenuation performance of the PS-TMD is better than the PTMD.In addition,the PS-TMD avoids the nonlinear effect due to the large oscillation angle,and has the potential to dissipate hysteretic energy under seismic excitation.

Development and Application of a Power Law Constitutive Model for Eddy Current Dampers

Eddy current dampers (ECDs) have emerged as highly desirable solutions for vibration control due to theirexceptional damping performance and durability. However, the existing constitutive models present challenges tothe widespread implementation of ECD technology, and there is limited availability of finite element analysis (FEA)software capable of accurately modeling the behavior of ECDs. This study addresses these issues by developing anewconstitutivemodel that is both easily understandable and user-friendly for FEAsoftware. By utilizing numericalresults obtained from electromagnetic FEA, a novel power law constitutive model is proposed to capture thenonlinear behavior of ECDs. The effectiveness of the power law constitutive model is validated throughmechanicalproperty tests and numerical seismic analysis. Furthermore, a detailed description of the application process ofthe power law constitutive model in ANSYS FEA software is provided. To facilitate the preliminary design ofECDs, an analytical derivation of energy dissipation and parameter optimization for ECDs under harmonicmotionis performed. The results demonstrate that the power law constitutive model serves as a viable alternative forconducting dynamic analysis using FEA and optimizing parameters for ECDs.

Parameters Optimization and Performance Evaluation of the Tuned Inerter Damper for the Seismic Protection of Adjacent Building Structures

In order to improve the seismic performance of adjacent buildings,two types of tuned inerter damper(TID)damping systems for adjacent buildings are proposed,which are composed of springs,inerter devices and dampers in serial or in parallel.The dynamic equations of TID adjacent building damping systems were derived,and the H2 norm criterion was used to optimize and adjust them,so that the system had the optimum damping performance under white noise random excitation.Taking TID frequency ratio and damping ratio as optimization parameters,the optimum analytical solutions of the displacement frequency response of the undamped structure under white noise excitation were obtained.The results showed that compared with the classic TMD,TID could obtain a better damping effect in the adjacent buildings.Comparing the TIDs composed of serial or parallel,it was found that the parallel TIDs had more significant advantages in controlling the peak displacement frequency response,while the H2 norm of the displacement frequency response of the damping system under the coupling of serial TID was smaller.Taking the adjacent building composed of two ten-story frame structures as an example,the displacement and energy collection time history analysis of the adjacent building coupled with the optimum design parameter TIDs were carried out.It was found that TID had a better damping effect in the full-time range compared with the classic TMD.This paper also studied the potential power of TID in adjacent buildings,which can be converted into available power resources during earthquakes.

Seismic Resilience Analysis of a Concrete-Framed Hospital Building with Viscous Dampers

To study the seismic resilience of a concrete-framed hospital building with viscous dampers,the elastoplastic time history analysis of a three-story concrete-framed hospital building under moderate and rare earthquakes was carried out by finite element analysis software.The structure’s overall response was studied,meanwhile,the seismic resilience of the building was evaluated from three aspects:repair cost,repair time,and casualties.The results show that viscous dampers can effectively reduce the repair cost,repair time,and casualties under earthquakes.Compared with the structure without dampers,the repair cost and repair time of the structure with dampers have been reduced by 67%and 69%respectively under moderate earthquakes,42%and 39%respectively under rare earthquakes,and the seismic resilience grade has been increased from zero to one star.

Modeling of Magneto-Rheological Damper with Neural Network

With the revival of magnetorheological technology research in the 1980’s, its application in vehicles is in- creasingly focused on vibration suppression. Based on the importance of magnetorheological damper modeling, non- parametric modeling with neural network, which is a promising development in semi-active online control of vehicles with MR suspension, has been carried out in this study. A two layer neural network with 7 neurons in a hidden layer and 3 inputs and 1 output was established to simulate the behavior of MR damper at different excitation currents. In the neural network modeling, the damping force is a function of displacement, velocity and the applied current. A MR damper for vehicles is fabricated and tested by MTS; the data acquired are utilized for neural network training and vali- dation. The application and validation show that the predicted forces of the neural network match well with the forces tested with a small variance, which demonstrates the effectiveness and precision of neural network modeling.

Semi-active control for vibration attenuation of vehicle suspension with symmetric MR damper

A semi-active force tracking PI controller is formulated and analyzed for a magnetorheological (MR) fluid-based damper in conjunction with a quarter-vehicle model. Two different models of the MR-damper are integrated into the closed-loop system model, which includes: a model based upon the mean force-velocity (f-v) behaviour; and a model synthesis comprising inherent nonsmooth hysteretic force and the force limiting properties of the MR damper. The vehicle models are analyzed to study the vibration attenuation performance of the MR-damper using the semi-active force tracking PI control algorithm. The simulation results are also presented to demonstrate the influence of the damper nonlinearity, specifically the hysteresis, on the suspension performance. The results show that the proposed control strategy can yield superior vibration attenuation performance of the vehicle suspension actuated by the controllable MR-damper not only in the sprung mass resonance and the ride zones, but also in the vicinity of the wheel-hop. The results further show that the presence of damper hystersis deteriorates the suspension performance.

NEURAL NETWORK REALIZATION OF STRUCTURAL VIBRATION CONTROL USING MR DAMPER

Magnetorheological (MR) dampers are one of the most promising new devices for civil infrastructural vibration control applications. However, due to their highly nonlinear dynamic behavior, it is very difficult to obtain of a mathematical model of inverse MR damper that has an explicit relationship between the desired damper force and the command signal (voltage). This force voltage relationship is especially required for the structural vibration control design and simulation using MR dampers. This paper focuses on using a neural network (NN) technique to emulate the inverse MR damper model. The output of the neural network can be used to command the MR damper for generating desired forces. Numerical simulations are also presented to illustrate the effectiveness of this inverse model in semi active vibration control using MR dampers.

Novel magneto-rheological fluid damper for passive force/torque feedback

The damper is capable of providing a continuously variable dampering force/torque in response to a magnetic field. It consists of an upside cap and an underside cap with a rotor located between them, the magneto-rheological （MR） fluid is filled into the gaps between the rotor and the caps. When the viscosity of the MR fluid increases under the influence of the magnetic field, the movement of the rotor will be resisted. The output torque is made up of the torque caused by the magnetic field, the torque caused by the plastic viscosity of the MR fluid, and the torque caused by the coulomb friction. The viscous torque can be calculated by a simple method and the frictional torque can be obtained by experiments. The torque dependent on the magnetic field is obtained by electromagnetic finite dement analysis. Experiments are done on the damper prototype and the validity of the design is verified.

DYNAMIC ANALYSIS OF DAMPER CONNECTED ADJACENT BUILDINGS UNDER EARTHQUAKE

A formulation of the multi degree of freedom equations of motion for damper connected adjacent multi story buildings under earthquake excitation is presented.The ground acceleration due to earthquake is regarded as a stochastic process,and a pseudo excitation algorithm in frequency domain is implemented in a computer program to handle the non orthogonal damping properties of the system.The effectiveness of joint dampers is then investigated in terms of the reduction of displacement,acceleration and shear force responses of adjacent buildings.

Efficiency of the motion amplification device with viscous dampers and its application in high-rise buildings

After nearly a decade of application and investigation, a motion amplification device with viscous dampers for energy dissipation has been recognized as an effective solution to mitigate wind or seismic excitation, especially for stiff structural systems. As a result of compensation of amplified motion, it has been proved that the efficiency of viscous damper largely depends on the motion amplification device configuration, particularly for device stiflhess. In this paper, a ＂scissor-jack＂ type of motion amplification device, called a ＂toggle brace damper＂ system, is studied. It is demonstrated that the efficiency of such a device reflected by its amplification factor is not merely a function of its geometric configuration, but is highly dependent on the support elements＇ stiffness as well, similar to the mechanism of a leverage arm. Accordingly, a mathematical model in terms of complex modulus of the viscous damper with consideration of the support brace＇s stiffness is established. The results indicate that the efficiency of the motion amplification device with viscous dampers significantly depends on the stiffness of the support elements. Other parameters, such as toggle brace configuration and damping values of the viscous damper, are studied and compared. As an application example, numerical analyses are conducted to study the dynamic performance of a 39-story office tower installed with toggle brace dampers constructed on soft soil in a reclaimed area, under a combined effect of the vortex shedding of an adjacent existing 52-story building and earthquakes. The results show that viscous dampers with a motion amplification system using a properly designed toggle brace device proved to be an effective solution to alleviate the external excitations.

Performance evaluation of a novel rotational damper for structural reinforcement steel frames subjected to lateral excitations

In this study,a novel rotational damper called a Rotational Friction Viscoelastic Damper(RFVD) is introduced.Some viscoelastic pads are added to the Rotational Friction Damper(RFD) in addition to the friction discs used in this conventional device.Consequently,the amount of energy dissipated by the damper increases in low excitation frequencies.In fact,the input energy to the structure is simultaneously dissipated in the form of friction and heat by frictional discs and viscoelastic pads.In order to compare the performance of this novel damper with the earlier types,a set of experiments were carried out.According to the test results,the RFVD showed a better performance in dissipating input energy to the structure when compared to the RFD.The seismic behavior of steel frames equipped with these dampers was also numerically evaluated based on a nonlinear time history analysis.The numerical results verifi ed the performance of the dampers in increasing the energy dissipation and decreasing the energy input to the structural elements.In order to achieve the maximum dissipated energy,the dampers need to be installed in certain places called critical points in the structure.An appropriate approach is presented to properly fi nd these points.Finally,the performance of the RFVDs installed at these critical points was investigated in comparison to some other confi gurations and the validity of the suggested method in increasing the energy dissipation was confi rmed.

Seismic analysis of structures with a fractional derivative model of viscoelastic dampers

Viscoelastic dampers are now among some of the preferred energy dissipation devices used for passive seismic response control.To evaluate the performance of structures installed with viscoelastic dampers,different analytical models have been used to characterize their dynamic force deformation characteristics.The fractional derivative models have received favorable attention as they can capture the frequency dependence of the material stiffness and damping properties observed in the tests very well.However,accurate analytical procedures are needed to calculate the response of structures with such damper models.This paper presents a modal analysis approach,similar to that used for the analysis of linear systems,for solving the equations of inotion with fractional derivative terms for arbitrary forcing functions such as those caused by earthquake induced ground motions.The uncoupled modal equations still have fractional derivatives,but can be solved by numerical or analytical procedures.Both numerical and analytical procedures are formulated.These procedures are then used to calculate the dynamic response of a multi-degree of fleedom shear beam structure excited by ground motions. Numerical results demonstrating the response reducing effect of viscoelastic dampers are also presented.

Skyhook-based Semi-active Control of Full-vehicle Suspension with Magneto-rheological Dampers

The control study of vehicle semi-active suspension with magneto-rheological (MR) dampers has been attracted much attention internationally. However, a simple, real time and easy implementing semi-active controller has not been proposed for the MR full-vehicle suspension system, and a systematic analysis method has not been established for evaluating the multi-objective suspension performances of MR full-vehicle vertical, pitch and roll motions. For this purpose, according to the 7-degree of freedom (DOF) fullvehicle dynamic system, a generalized 7-DOF MR and passive full-vehicle dynamic model is set up by employing the modified Boucwen hysteretic force-velocity (F-v) model of the MR damper. A semi-active controller is synthesized to realize independent control of the four MR quarter-vehicle sub-suspension systems in the full-vehicle, which is on the basis of the proposed modified skyhook damping scheme of MR quarter-vehicle sub-suspension system. The proposed controller can greatly simplify the controller design complexity of MR full-vehicle suspension and has merits of easy implementation in real application, wherein only absolute velocities of sprung and unsprung masses with reference to the road surface are required to measure in real time when the vehicle is moving. Furthermore, a systematic analysis method is established for evaluating the vertical, pitch and roll motion properties of both MR and passive full-vehicle suspensions in a more realistic road excitation manner, in which the harmonic, rounded pulse and real road measured random signals with delay time are employed as different road excitations inserted on the front and rear two wheels, by considering the distance between front and rear wheels in full-vehicle. The above excitations with different amplitudes are further employed as the road excitations inserted on left and right two wheels for evaluating the roll motion property. The multi-objective suspension performances of ride comfort and handling safety of the proposed MR full-vehicle suspension are thus thoroughly evaluated by comparing with those of the passive full-vehicle suspension. The results show that the proposed controller can ideally improve multiobjective suspension performances of the ride comfort and handling safety. The proposed harmonic, rounded pulse and real road measured random signals with delay time and asymmetric amplitudes are suitable for accurately analyzing the vertical, pitch and roll motion properties of MR full-vehicle suspension system in a more realistic road excitation manner. This research has important theoretical significance for improving application study on the intelligent MR semi-active suspension.

Adaptive Control of Helicopter Ground Resonance with Magnetorheological Damper

The methodology for adaptive control of helicopter ground resonance with magnetorheological （MR） damper is presented. The adaptive inverse control method is used to control the output damping force of MR damper and the range of the damping force is given. Through the adaptive inverse control, the damping force of MR damper is fit to a desired damping force. With the background of applying MR damper to control of helicopter ground resonance, a model of loss force and an adaptive arithmetic for stabilization of the coupled rotor/fuselage system are presented. The simulation shows that the controller presented in this paper can stabilize the rotor/fuselage coupling system quickly and control the helicopter ground resonance effectively.

GENERALIZED ASYMMETRIC HYSTERESIS MODEL OF CONTROLLABLE MAGNETORHEOLOGICAL DAMPER FOR VEHICLE SUSPENSION ATTENUATION

A generalized model is synthesized to characterize the asymmetric hysteresisforce-velocity (F-v) properties of the magneto-rheological (MR) fluids damper. The model isrepresented as a function of the command current, excitation frequency, and displacement amplitude,based on the symmetric and asymmetric sigmoid functions. The symmetric hysteresis damping propertiesof the controllable MR-damper and properties of the conventional passive hydraulic damper can alsobe described by the proposed model. The validity of the model is verified by experiments, which showthat the results calculated from the model are consistent with the measured data. In addition, itis shown that the model applies to a wide vibration frequency range. The proposed model haspotential application in vehicle suspension design employing the symmetry MR-damper, and also indeveloping the asymmetry MR-damper especially for the vehicle suspension attenuation.

Development of steel dampers for bridges to allow large displacement through a vertical free mechanism

Isolation bearings and dampers are often installed between piers and superstructures to reduce the seismic responses of bridges under large earthquakes. This paper presents a novel steel damper for bridges. The damper employs steel plates as energy dissipation components, and adopts a vertical free mechanism to achieve a large deformation capacity. Quasi-static tests using displacement-controlled cyclic loading and numerical analyses using a finite element program called ABAQUS are conducted to investigate the behavior of the damper, and a design methodology is proposed based on the tests and numerical analyses. Major conclusions obtained from this study are as follows： （1） the new dampers have stable hysteresis behavior under large displacements; （2） finite element analyses are able to simulate the behavior of the damper with satisfactory accuracy; and （3） simplified design methodology of the damper is effective.

Optimal PD/PID control of smart base isolated buildings equipped with piezoelectric friction dampers

Long-period pulses in near-field earthquakes lead to large displacements in the base of isolated structures.To dissipate energy in isolated structures using semi-active control,piezoelectric friction dampers（PFD） can be employed.The performance of a PFD is highly dependent on the strategy applied to adjust its contact force.In this paper,the seismic control of a benchmark isolated building equipped with PFD using PD/PID controllers is developed.Using genetic algorithms,these controllers are optimized to create a balance between the performance and robustness of the closed-loop structural system.One advantage of this technique is that the controller forces can easily be estimated.In addition,the structure is equipped with only a single sensor at the base floor to measure the base displacement.Considering seven pairs of earthquakes and nine performance indices,the performance of the closed-loop system is evaluated.Then,the results are compared with those given by two well-known methods：the maximum possive operation of piezoelectric friction dampers and LQG controllers.The simulation results show that the proposed controllers perform better than the others in terms of simultaneous reduction of floor acceleration and maximum displacement of the isolator.Moreover,they are able to reduce the displacement of the isolator systems for different earthquakes without losing the advantages of isolation.