IMPROVING MATERIAL REMOVAL RATE OF BRITTLE CERAMICS THROUGH HONING INCIDENTAL TENSILE STRESSES

The stress intensity factors and stress conditions of machining cracks are analyzed by fracture mechanics on the basis of honing characteristics and of brittle ceramic mechanical behavior.Because the honing incidental tensile stresses effectively decrease the critical grinding stresses and increase the stress intensity factors of machining cracks,the honing process can be carried out easily.The results show that honing can be an efficient machining method for brittle materials.

Analysis of Material Removal in Alumina Ceramic Honing

The removal mechanism is of importance to the grinding of hard and brittle ceramic materials. It is more suitable to analyze the material removal during ceramics honing processes by means of indention fracture approach. There are two honing characteristics different from grinding, the honing incidental tensile stresses and the crosshatch pattern. The stresses may influence material removal of brittle ceramics with lower tensile strength. In addition, the criss-cross cutting pattern on a bore known as crosshatch may also have its effect on the material removal of ceramics. The material removal of alumina is analyzed on the basis of honing characteristics, honing incidental tensile stresses and crosshatch pattern. By means of indentation fracture mechanics of brittle solids, the theoretical analysis of stress intensity factor and the crack response prove that honing incidental tensile stresses can increase the stress intensity factor of honing cracks and decrease the grinding stresses. So, the fracture criterion for crack propagation can be met easily. Therfore, it is possible to machine ceramic materials with small grinding forces in honing processes. The alumina honing experiments show that material at crosshatch intersecting point is removed by way of chipping which is similar to the edge-crumbled of ceramics. For brittle ceramics with lower tensile strength, such as Al 2O 3, SiO 2, the influences of the honing incidental tensile stresses and the crosshatch pattern on material removal are bigger than that of ceramics with relative higher toughness, such as ZrO 2 and Si 3N 4. Hence, the honing of Al 2O 3, SiO 2, is superior in cutting ability to the grinding. The large stock removal of brittle ceramic materials can be obtained through higher honing pressures. The increase in honing pressures can increase intensity factor of honing cracks, decrease the grinding stresses, and remarkably improve material removal rate. The researches show that honing is an efficient bore machining operation for brittle ceramics.

Material Removal Behavior and Surface Integrity in Grinding of UltrafineGrained WC-Co Materials

Due to the excellent combination of wear resistance and fracture toughness,the ultrafine-grained WC-Co composites can significantly improve the durability and reliability of industrial tools.However,the grinding of ultrafine-grained WC-Co remains a challenge.In order to provide an experimental basis for improving grinding quality of ultrafine-grained WC-Co,a series of surface grinding experiments on ultrafine-grained WC-Co hardmetals were conducted by diamond wheel under various grinding conditions,and the material removal behavior and surface integrity in grinding of ultrafine-grained WC-Co materials were characterized by means of scanning electron microscopy(SEM),X-ray microstress analyzer and surface roughness analyzer in this paper.The results indicate that the material removal behavior in grinding of ultrafine-grained WC-Co materials is determined not only by the abrasive grain size on the wheel,but also by the depth of cut.The roughness values of ground surface increase with increasing grit size of diamond wheel,and increase initially,then decrease with increase in depth of cut.Grinding causes the residual compressive stress in the surface layer of ground cemented carbides under various grinding conditions;the magnitude of residual surface stress increases with increasing grit size of diamond wheel,and isn't changed obviously along with the change of depth of cut.

Residual Stress Distribution of Si_(3)N_(4)/SiC Gradient Material and the Effect of Residual Stress on Material Properties

The Si_(3)N_(4)/SiC gradient material with a gradient composition structure was prepared by a hot pressing sintering.The sinterability,distribution of residual stress and the effect of residual stress on mechanical properties of Si_(3)N_(4)/SiC gradient materials were studied.The research results show that,at 1750℃,Si_(3)N_(4)/SiC gradient materials with different ratios can achieve co-sintering,and the overall relative density of the sample reaches 98.5%.Interestingly,the flexural strength of Si_(3)N_(4)/SiC gradient material is related to its loading surface.The flexural strength of SiC as the loading surface is about 35%higher than that of Si_(3)N_(4)as the loading surface.The analysis of the residual stress of the material in the gradient structure shows that the gradient stress distribution between the two phases is a vital factor affecting the mechanical properties of the material.With the increase of SiC content in the gradient direction,the fracture toughness of each layer of Si_(3)N_(4)/SiC gradient materials gradually decreases.The surface hardness of the pure SiC side is lower than that reported in other literature.

Fatigue Life Prediction for SiC/Al Materials Based on Path Planning Algorithm Considering Residual Stress

To explore the influence of path deflection on crack propagation,a path planning algorithm is presented to calculate the crack growth length.The fatigue crack growth life of metal matrix composites(MMCs)is estimated based on an improved Paris formula.Considering the different expansion coefficient of different materials,the unequal shrinkage will lead to residual stress when the composite is molded and cooled.The crack growth model is improved by the modified stress ratio based on residual stress.The Dijkstra algorithm is introduced to avoid the cracks passing through the strengthening base and the characteristics of crack steps.This model can be extended to predict crack growth length for other similarly-structured composite materials.The shortest path of crack growth is simulated by using path planning algorithm,and the fatigue life of composites is calculated based on the shortest path and improved model.And the residual stress caused by temperature change is considered to improve the fatigue crack growth model in the material.The improved model can well predict the fatigue life curve of composites.By analyzing the fatigue life of composites,it is found that there is a certain regularity based on metal materials,and the new fatigue prediction model can also reflect this regularity.

Optimization design and residual thermal stress analysis of PDC functionally graded materials

The distribution of thermal stresses in functionally graded polycrystalline diamond compact (PDC) and in single coating of PDC are analyzed respectively by thermo-mechanical finite element analysis (FEA). It is shown that they each have a remarkable stress concentration at the edge of the interfaces. The diamond coatings usually suffer premature failure because of spallation, distortion or defects such as cracks near the interface due to these excessive residual stresses. Results showed that the axial tensile stress in FGM coating is reduced from 840 MPa to 229 MPa compared with single coating, and that the shear stress is reduced from 671 MPa to 471 MPa. Therefore, the single coating is more prone to spallation and cracking than the FGM coating. The effects of the volume compositional distribution factor (n) and the number of the graded layers (L) on the thermal stresses in FGM coating are also discussed respectively. Modelling results showed that the optimum value of the compositional distribution factor is 1.2, and that the best number of the graded layers is 6.

MODIFIED LAYER REMOVAL METHOD FOR MEASUREMENT OF RESIDUAL STRESS DISTRIBUTION IN THICK PRE-STRETCHED ALUMINUM PLATE

The integrated structure parts are widely used in aircraft. The distortion caused by residual stresses in thick pre-stretched aluminum plates during machining integrated parts is a common and serious problem. To predict and control the machining distortion, the residual stress distribution in the thick plate must be measured firstly. The modified removal method for measuring residual stress in thick pre-stretched aluminum plates is proposed and the stress-strain relation matrix is deduced by elasticity theory. The residual stress distribution in specimen of 7050T7451 plate is measured by using the method, and measurement results are analyzed and compared with data obtained by other methods. The method is effective to measure the residual stress.

Theoretical study and numerical simulation of the stress fields of the Al_2O_3 joints brazed with composite filler materials

Non-linear finite element code MSC. Marc was utilized to analysis the field of stress of the Al2O3 joints brazed with composite filler materials. The properties of the filler materials were defined by using the mixing law, method of Mori-Tanaka and theory of Eshelby to ensure the accuracy and reliability of results of finite element method （FEM）. The results show stress in brazed beam is higher than that in base material. The maximal stress can be found in the interface of joint. And the experimental results show that the shear strength of joints increases from 93.75 MPa （ Al2O3p Ovol. % ） to 135.32 MPa （ Al2O3p 15vol. % ） when composition of titanium is 3wt% in the filler metal.

Residual stress with asymmetric spray quenching for thick aluminum alloy plates

Solution and quenching heat treatments are generally carried out in a roller hearth furnace for large-scale thick aluminum alloy plates.However,the asymmetric or uneven spray water flow rate is inevitable under industrial production conditions,which leads to an asymmetric residual stress distribution.The spray quenching treatment was conducted on self-designed spray equipment,and the residual stress along the thickness direction was measured by a layer removal method based on deflections.Under the asymmetric spray quenching condition,the subsurface stress of the high-flow rate surface was lower than that of the low-flow rate surface,and the difference between the two subsurface stresses increased with the increase in the difference in water flow rates.The subsurface stress underneath the surface with a water flow rate of 0.60 m^(3)/h was 15.38 MPa less than that of 0.15 m^(3)/h.The simulated residual stress by finite element(FE)method of the high heat transfer coefficient(HTC)surface was less than that of the low HTC surface,which is consistent with the experimental results.The FE model can be used to analyze the strain and stress evolution and predict the quenched stress magnitude and distribution.

Literature Review of Electronic Packaging Technology and Residual Stress

The rapid development of the electronic information industry brings to the irreplaceable role of electronic components, therefore the search of a more reliable packaging material has become increasingly important. In the electronic packaging system, the failure phenomenon caused by residual stress is one of the key factors restricting the development of electronic packaging technology. In order to use the in-situ characterization technology to explore the residual stress inducing mechanism and failure mechanism of epoxy-based advanced packaging materials, this paper gives a review of related previous research, and lays a theoretical foundation for the upcoming research. The classification and generation mechanism of residual stress are clarified in this paper, which provides data support for future related research.

Modified Layer-Removal Method for Measurement of Residual Stress in Pre-stretched Aluminium Alloy Plate

Residual stress is one of the factors affecting the machining deformation of monolithic structure parts in the aviation industry. Thus, the studies on machining deformation rules induced by residual stresses largely depend on correctly and efficiently measuring the residual stresses of workpieccs. A modified layer-removal method is proposed to measure residual stress by analysing the characteristics of a traditional, layer-removal method. The coefficients of strain release are then deduced according to the simulation results using the finite element method （FEM）. Moreover, the residual stress in a 7075T651 aluminium alloy plate is measured using the proposed method, and the results are then analyzed and compared with the data obtained by the traditional methods. The analysis indicates that the modified layer-removal method is effective and practical for measuring the residual stress distribution in pre-stretched aluminium alloy plates.

Numerical Simulation of Residual Stress during Microlayer Composite Material Processing by EBPVD Technique

The preparation technology of microlayer composite material by the electron beam physical vapor deposition (EBPVD) technique was briefly introduced. Taking the advantage of the large-scale commercial softvare of finite element analysis, areasonable physical model was built up during the deposition processing and the distribution of residual stress was analyzedbetween substrate and deposition layer or among deposition layers. The results show that: with the increasing substrate preheating temperature, the interlaminar shear stress increases but the axial residual stress decreases. The probability of curlingup after de-bonding tends to enhance as the thickness of deposition film increases.

Initial residual stress experiment and simulation of thin-walled parts for layer removal method

Thin-walled parts have low stiffness characteristic. Initial residual stress of thin-walled blanks is an important influence factor on machining stability. The present work is to verify the feasibility of an initial residual stress measurement of layer removal method. According to initial residual stress experiment for casting ZL205 A aluminum alloy tapered thin-walled blank by a common method,namely hole-drilling method,three finite element models with initial residual stress are established to simulate the layer removal method in ABAQUS and ANSYS software. By analyzing the results of simulation and experiments,the cutting residual stress inlayer removal process has a significant effect on measurement results. Reducing cutting residual stress is helpful to improve accuracy of layer removal method.

Energy principle and material removal sequence optimization method in machining of aircraft monolithic parts

In the machining process of aircraft monolithic parts,the initial residual stress redistribution and structural stiffness evolution often lead to unexpected distortions.On the other hand,the stress redistribution and stiffness reduction during the machining process depend on the material removal sequence.The essence of the stress redistribution is releasing the initial elastic strain energy.In the present study,the influence of the material removal sequence on the energy release is studied.Moreover,a novel optimization method is proposed for the material removal sequence.In order to evaluate the performance of the proposed method,the mechanism of the machining distortion is firstly analyzed based on the energy principle.Then a calculative model for the machining distortion of long beam parts is established accordingly.Moreover,an energy parameter related to the bending distortion and the procedure of the material removal sequence optimization is defined.Finally,the bending distortion analysis and material removal sequence optimization are performed on a long beam with a Z-shaped cross-section.Furthermore,simulation and experiments are carried out.The obtained results indicate that the optimized sequence results in a low distortion fluctuation and decreases the bending distortion.

Influence of Tacking Sequence on Residual Stress and Distortion of Single Sided Fillet Submerged Arc Welded Joint

Submerged arc welding （SAW） is advantageous for joining high thickness materials in large structure due to high material deposition rate. The non-uniform heating and cooling generates the thermal stresses and subsequently the residual stresses and distortion. The longitudinal and transverse residual stresses and angular distortion are generally measured in large panel structure of submerged arc welded fillet joints. Hence, the objective of this present work is to quantify the amount of residual stress and distortion in and around the weld joint due to positioning of stiffeners tack. The tacking sequence influences the level of residual stress and proper controlling of tacking sequences is required to minimize the stress. In present study, an elasto-plastic material behavior is considered to develop the thermo mechanical model which predicts the residual stress and angular distortion with varying tacking sequences. The simulated result reveals that the tacking sequence heavily influences the residual stress and deformation pattern of the single sided fillet joint. The finite element based numerical model is calibrated by comparing the experimental data from published literature. Henceforth, the angular distortions are measured from an in-house developed experimental set-up. A fair agreement between the predicted and experimental results indicates the robustness of the developed numerical model. However, the most significant conclusion from present study states that tack weld position should be placed opposite to the fillet weld side to minimize the residual stress.

Measurement of Residual Stress Field of Hardfacing Metal with RE Oxide and Its Numerical Simulation

The temperature and residual stress fields of a medium-high carbon steel, welded by a cracking resistance electrode with rare earth (RE) oxide, were measured by thermo-vision analyzer and X-ray stress analyzer respectively. Meanwhile, the martensitic transformation temperatures of matrix, hard-face welding (hardfacing) metal welded by conventional hardfacing electrode and that welded by cracking resistance electrode with RE oxide were determined. According to the experimental data and the thermo-physical, mechanical parameters of materials, finite element method (FEM) of temperature and stress fields was established. In this FEM, the effect of martensitic transformation on residual stress of hardfacing metal of medium-high carbon steel was taken into account. The results show that, by adding RE oxide in the coat of hardfacing electrode, the martensitic transformation temperature can be decreased, so that the residual tensile stress on the dangerous position can be decreased. Therefore, the cracking resistance of hardfacing metal can be improved.

EXPERIMENTAL STUDY OF EFFECTS ON DELAMINATION NEAR CRACK OF ARALL BY RESIDUAL STRESS UNDER FATIGUE ＆ STATIC LOADS

The delamination near the centre crack of ARALL under fatigue and static loads is investigated, and the effects on delamination by different residual stresses are analyzed. The results show that the situations under the two kinds of loads are different.Under the fatigue load, the typical delamination with crack growth presents symmetrical hi-ellipse-shape, whereas under the condition of static tensile, the edge-effect becomes more evident. Applying a proper pre-stress to the laminate can increase the ability of anti-delamination damage.

熔石英元件磁性复合流体抛光去除特性研究

基于磁性复合流体(Magnetic Compound Fluid,MCF)抛光技术开展了熔石英元件抛光工艺研究,对比了传统MCF和超声辅助MCF(以下简称UMCF)抛光对熔石英材料去除特性的影响,探究了不同抛光时间下MCF和UMCF抛光对熔石英材料去除量/去除率和表面粗糙度的影响,并构建了与抛光应力和抛光时间有关的材料去除率模型。研究结果表明,相较于传统MCF,UMCF在提高材料去除率和降低表面粗糙度方面均有优势。两种抛光方式下材料去除机制均为弹塑性去除,UMCF抛光获得的表面粗糙度相比于MCF抛光优化了68.88%。由于流体动压力和超声振动压力的联合作用,UMCF抛光材料去除率最高可达5.74×10^(-3)mm^(3)/min,相比于MCF抛光提升了4.04倍。MCF和UMCF抛光材料去除率与抛光应力和抛光时间均呈现幂函数相关性,且在UMCF抛光中抛光应力对去除率的影响权重大于MCF抛光。

表面效应对热-机多孔悬臂纳米梁力学性能的影响

表面效应对纳米结构的力学性能有重要影响。飞机上很多微纳尺度的结构可简化为悬臂梁。本工作分析表面效应对随从载荷作用下梯度多孔材料纳米悬臂梁在高温环境下非线性力学响应的影响。基于GurtinMurdoch表面弹性理论和非线性梁理论,建立梯度多孔材料梁在随从载荷以及温度场中的非线性控制微分方程。假定梯度多孔材料的性能在整个厚度范围内连续变化,且沿厚度呈两种余弦形式的非均匀孔隙率分布模式。采用打靶法求解梯度多孔材料悬臂纳米梁在热-随从载荷下的非线性力学响应。获得各种孔隙率系数和不同非均匀升温下悬臂纳米梁非线性力学响应的数值解,详细讨论材料表面弹性常数和表面应力对纳米悬臂梁力学响应的影响。结果表明:不同孔隙率系数和不同非均匀升温下梁的力学行为是不同的;纳米梁表现出十分显著的表面效应。

钛合金材料超声滚压加工的仿真分析与实验研究

采用普通滚压加工工艺对钛合金材料进行加工时,存在因低频冲击造成的工件残余应力分布不均匀和表面硬度低等问题,为此,开展了钛合金材料超声振动滚压工艺仿真及实验研究。首先,从理论层面分析了超声滚压加工的运动学及动力学特性,找出了影响超声滚压加工性能的相关因素;然后,采用ABAQUS有限元软件建立了钛合金材料的仿真模型,分析了超声滚压对残余应力的影响及强化机理;最后,设计了钛合金工件的超声滚压实验,研究了不同参数指标对工件加工质量的影响,并根据实验结果对仿真模型和残余应力结果进行了验证。研究结果表明:随着静载荷和超声振幅的增加,工件表面残余应力分布相对均匀且趋于平稳,表面粗糙度呈现先降低后增加的趋势,表面硬度随强化层深度的增加逐渐降低;在振幅为20μm时,工件表面质量和性能相对较好,此时残余应力均值为849 MPa,表面粗糙度均值为0.1μm。该实验结果与仿真分析结果一致,验证了所建模型的可靠性,可为滚压制造工艺参数的选取提供参考。