Comparison study on measurement of rail weld joint between inertial reference method and multi-point chord reference method

Purpose – Straightness measurement of rail weld joint is of essential importance to railway maintenance. Dueto the lack of efficient measurement equipment, there has been limited in-depth research on rail weld joint with a5-m wavelength range, leaving a significant knowledge gap in this field.Design/methodology/approach – In this study, the authors used the well-established inertial referencemethod (IR-method), and the state-of-the-art multi-point chord reference method (MCR-method). Two methodshave been applied in different types of rail straightness measurement trollies, respectively. These instrumentswere tested in a high-speed rail section within a certain region of China. The test results were ultimatelyvalidated through using traditional straightedge and feeler gauge methods as reference data to evaluate the railweld joint straightness within the 5-m wavelength range.Findings – The research reveals that IR-method and MCR-method produce reasonably similar measurementresults for wavelengths below 1 m. However, MCR-method outperforms IR-method in terms of accuracy forwavelengths exceeding 3 m. Furthermore, it was observed that IR-method, while operating at a slower speed,carries the risk of derailing and is incapable of detecting rail weld joints and low joints within the track.Originality/value – The research compare two methods’ measurement effects in a longer wavelength rangeand demonstrate the superiority of MCR-method.

Development of a Certified Reference Material from Caffeine Solution for Assuring the Quality of Food and Drug Measurements

Caffeine intake by pregnant women, adults and children can be harmful to the health of all particularly fetuses if the intake exceeds the permissible limits. Therefore, it is of fundamental importance to measure its concentration accurately using certified reference materials (CRMs). In the literature, no scientific details are published about the certification of caffeine standard solutions, and therefore, the present article covers this gap. A batch of caffeine solution was prepared in concentration of 1000 mg/kg and bottled. Homogeneity and stability of the candidate reference material were assessed by HPLC-UV and the results showed that the material is homogenous and stable enough. Characterization of the caffeine reference material was performed by HPLC-UV, LC-MS/MS and UV-VIS-NIR spectrophotometer in three different days and the characterization uncertainty was estimated in accordance with the requirements of ISO GUM. The certified value (999.86 ± 8.57 mg/kg) was derived as a weighted mean from the gravimetry and the three characterization methods and the certified uncertainty was calculated according to ISO Guide 35. The produced CRM is of strong interest to the food and drug analytical laboratories for the validity and credibility of their caffeine measurement results.

Development of a Certified Reference Material from Caffeine Solution for Assuring the Quality of Food and Drug Measurements

Caffeine intake by pregnant women, adults and children can be harmful to the health of all particularly fetuses if the intake exceeds the permissible limits. Therefore, it is of fundamental importance to measure its concentration accurately using certified reference materials (CRMs). In the literature, no scientific details are published about the certification of caffeine standard solutions, and therefore, the present article covers this gap. A batch of caffeine solution was prepared in concentration of 1000 mg/kg and bottled. Homogeneity and stability of the candidate reference material were assessed by HPLC-UV and the results showed that the material is homogenous and stable enough. Characterization of the caffeine reference material was performed by HPLC-UV, LC-MS/MS and UV-VIS-NIR spectrophotometer in three different days and the characterization uncertainty was estimated in accordance with the requirements of ISO GUM. The certified value (999.86 ± 8.57 mg/kg) was derived as a weighted mean from the gravimetry and the three characterization methods and the certified uncertainty was calculated according to ISO Guide 35. The produced CRM is of strong interest to the food and drug analytical laboratories for the validity and credibility of their caffeine measurement results.

Parameter-independent error correction for potential measurements by reference electrode in lithium-ion batteries

The safety monitoring of lithium-ion batteries(LIBs) is of great significance for realizing all-climate and full-lifespan battery management. In-situ measurement of anode potential with implanted reference electrodes(REs) has proven to be effective to monitor and avoid the occurrence of severe side reactions like Li plating to ensure the safe and fast charging. However, the intrinsic measurement errors caused by local blocking effects, which also can be referred to as potential artefacts, are seldom taken into consideration in existing studies, yet they highly dominate the correctness of conclusions inferred from REs. In this study, aiming at exploring the physical origin of the measurement errors and ensure reliable potential monitoring, electrochemical and post-mortem tests are conducted using commercial pouch cells with implanted REs. Corresponding electrochemical model which describes the blocking effects, is established to validate the abnormal absence of lithium plating that predicted by measured anode potentials under various charging rates. Theoretical derivation is further presented to explain the error sources, which can be attributed to increased local liquid potential of the RE position. Most importantly, with the guidance of error analysis, a novel parameter-independent error correction method for RE measurements is proposed for the first time, which is proven to be adequate to estimate the real anode potentials and deduce the critical C-rate of Li plating with extra safety margin. After error correction, the resulting critical C-rates are all within the range of 0.55 ± 0.03 C, which is close to the C-rate of 0.6–0.7 C obtained from experiments. In addition, this error correction method can be performed conveniently with only some simple RE measurements of polarization voltages, totally independent of battery electrochemical and geometric parameters. This study provides highly practical error correction method for RE measurements in real LIBs, substantially facilitating the fast diagnosis and safety evaluation of Li plating during charging of LIBs.

ELECTROCHEMICAL MEASUREMENTS FOR MARINE ATMOSPHERIC CORROSION STUDIES USING KELVIN PROBE REFERENCE ELECTRODE

A Kelvin probe was used as reference in this study on electrochemical measurements of a simulatedmarine atmospheric corrosion system (electrode covered by a very thin electrolyte layer). The experimentalsetups for improved measurements proved satisfactory for the conventional steady-state electrochemicalmeasurements in atmospheric studies.

General coarsened measurement references for revelation of a classical world

It has been found that for a fixed degree of fuzziness in the coarsened references of measurements,the quantum-toclassical transition can be observed independent of the macroscopicity of the quantum state.We explore a general situation that the degree of fuzziness can change with the rotation angle between two states（different rotation angles represent different references）.The fuzziness of reference comes from two kinds of fuzziness：the Hamiltonian（rotation frequency）and the timing（rotation time）.For the fuzziness of the Hamiltonian alone,the degree of fuzziness for the reference will change with the rotation angle between two states,and the quantum effects can still be observed with any degree of fuzziness of Hamiltonian.For the fuzziness of timing,the degree of the coarsening reference is unchanged with the rotation angle.During the rotation of the measurement axis,the decoherence environment can also help the classical-to-quantum transition due to changing the direction of the measurement axis.

Bunch-length measurement at a bunch-by-bunch rate based on time–frequency-domain joint analysis techniques and its application

This paper presents a new technique for measuring the bunch length of a high-energy electron beam at a bunch-by-bunch rate in storage rings.This technique uses the time–frequency-domain joint analysis of the bunch signal to obtain bunch-by-bunch and turn-by-turn longitudinal parameters,such as bunch length and synchronous phase.The bunch signal is obtained using a button electrode with a bandwidth of several gigahertz.The data acquisition device was a high-speed digital oscilloscope with a sampling rate of more than 10 GS/s,and the single-shot sampling data buffer covered thousands of turns.The bunch-length and synchronous phase information were extracted via offline calculations using Python scripts.The calibration coefficient of the system was determined using a commercial streak camera.Moreover,this technique was tested on two different storage rings and successfully captured various longitudinal transient processes during the harmonic cavity debugging process at the Shanghai Synchrotron Radiation Facility(SSRF),and longitudinal instabilities were observed during the single-bunch accumulation process at Hefei Light Source(HLS).For Gaussian-distribution bunches,the uncertainty of the bunch phase obtained using this technique was better than 0.2 ps,and the bunch-length uncertainty was better than 1 ps.The dynamic range exceeded 10 ms.This technology is a powerful and versatile beam diagnostic tool that can be conveniently deployed in high-energy electron storage rings.

A New Device for Gas-Liquid Flow Measurements Relying on Forced Annular Flow

A new measurement device,consisting of swirling blades and capsule-shaped throttling elements,is proposed in this study to eliminate typical measurement errors caused by complex flow patterns in gas-liquid flow.The swirling blades are used to transform the complex flow pattern into a forced annular flow.Drawing on the research of existing blockage flow meters and also exploiting the single-phase flow measurement theory,a formula is introduced to measure the phase-separated flow of gas and liquid.The formula requires the pressure ratio,Lockhart-Martinelli number(L-M number),and the gas phase Froude number.The unknown parameters appearing in the formula are fitted through numerical simulation using computational fluid dynamics(CFD),which involves a comprehensive analysis of the flow field inside the device from multiple perspectives,and takes into account the influence of pressure fluctuations.Finally,the measurement model is validated through an experimental error analysis.The results demonstrate that the measurement error can be maintained within±8%for various flow patterns,including stratified flow,bubble flow,and wave flow.

Design and application of thickness measurement calibration system based on laser displacement sensor

This study aims to improve the accuracy and safety of steel plate thickness calibration.A differential noncontact thickness measurement calibration system based on laser displacement sensors was designed to address the problems of low precision of traditional contact thickness gauges and radiation risks of radiation-based thickness gauges.First,the measurement method and measurement structure of the thickness calibration system were introduced.Then,the hardware circuit of the thickness system was established based on the STM32 core chip.Finally,the system software was designed to implement system control to filter algorithms and human-computer interaction.Experiments have proven the excellent performance of the differential noncontact thickness measurement calibration system based on laser displacement sensors,which not only considerably improves measurement accuracy but also effectively reduces safety risks during the measurement process.The system offers guiding significance and application value in the field of steel plate production and processing.

Candidate reference measurement procedure for serum 17-hydroxyprogesterone quantification via isotope dilution liquid chromatography–tandem mass spectrometry

Background:Accurate quantification of 17-hydroxyprogesterone(17-OHP)in serum is vital for clinical and research applications.However,inter-laboratory variability in test results exists owing to the lack of a standardized reference measurement procedure(RMP).Therefore,in this study,we developed a highly accurate,cost-effective,and user-friendly candidate RMP(cRMP)for analyzing 17-OHP in serum.Methods:We quantified 17-OHP in serum using a one-step liquid–liquid extraction method with the addition of 17-OHP-^(13)C_(3),followed by liquid chromatography–tandem mass spectrometry.The ability of these methods to suppress interference was evaluated by chromatographic analysis.We assessed accuracy,specificity,the lower limit of quantitation,linearity,and matrix effects by following the standards specified by the Clinical and Laboratory Standards Institute.The consistency between the developed cRMP and the chemiluminescence method was evaluated through experiments with 120 clinical samples.Results:The developed cRMP required only 8 min for accurate quantification of serum 17-OHP without bias from matrix effects or interference from 19 metabolites added as potential interferents.The method exhibited favorable measurement performance,with a quantitation limit of 0.086 ng/mL,linear range of 0.1–400 ng/mL,a total imprecision of≤2.90%,spike recovery of 100.1%–100.6%,and relative deviations from assigned target values(RfB Institution)of−2.91%to 1.10%.The cRMP demonstrated good consistency with the conventional assay(chemiluminescence method),with a correlation coefficient R of 0.96977.Conclusion:A cRMP with high accuracy,cost-effectiveness,and convenient operation was developed for quantifying 17-OHP in serum.Its simplicity and robust performance make it an invaluable addition to the arsenal of analytical tools available for laboratories.This method can enhance the accuracy and reliability of 17-OHP measurements across various laboratories.

Comparison of bulk snow density measurements using different methods

Snow density is one of the basic properties used to describe snow cover characteristics,and it is critical for remote sensing retrieval,water resources assessment and modeling inputs.There are many instruments available to measure snow density in situ.However,there are mea-surement errors of snow density for bulk and layers or gravimetric and electronic instruments,which may affect the accuracy of remote sensing retrieval and model simulation.Especially in China,due to the noticeable heterogeneity of snowpacks,it is necessary to evaluate in detail the performance and applicability of snow density instruments in different snowpack conditions.This study evaluated the performance of different snow density instruments:the Federal Sampler,the model VS-43 snow density cylinder(VS-43),the wedge snow density cutter(WC1000 and WC25O),and the Snow Fork.The average bulk snow density of all instrument measurements was set as the reference value for evaluation.The results showed that as compared with the reference,the VS-43 cylinder presented the best performance for bulk snow density measurement in the measured range with the lowest RMSE(11 kg m-3),BIAS(3 kg m-3),and MRE(1.6%).For layer observation,bulk snow density was overestimated by 8.1%with WC1000 and underestimated by 11.4%with Snow Fork which was the worst performance compared with the reference value,and there were greater measurement errors of snow density in the depth hoar than other snow layers.Compared with grassland,the uncertainty of snow density measurements was slightly lower in forests.Overall,the Federal Sampler and VS-43 cylinder are more suitable for bulk snow density measurement in deep snowpack regions across China,and it is recommended to use WC1000,WC250 and Snow Fork to measure the snow density of snow layers in the snow stratigraphy.

Pathological and Etiological Aspects of Nephrotic Syndrome at the Niamey General Reference Hospital

Introduction: Studies have been conducted on nephrotic syndrome in Niger. The study aimed to determine the histological and etiological aspects of nephrotic syndrome. Patients and Method: This was a retrospective study from February 1st, 2018 to January 31st, 2024. All patients with nephrotic syndrome who underwent renal biopsy were included. Samples were analyzed at the anatomy-cytology pathology laboratory of the Faculty of Medicine in Dakar (Senegal). The variables studied included clinical, biological, histological and etiological characteristics. Data were analyzed using Excel 2013 and Epi-info 7.2.0 software. Results: The study included 119 patients with nephrotic syndrome. Prevalence of nephrotic syndrome was 11.24%. The male-to-female ratio was 2.25:1. The mean age at diagnosis was between 34.5 ± 18.84 years. Edema was the reason for admission in 40.34% of cases. The nephrotic syndrome was impure in 63.86% of cases. Nine histological lesions were identified. Focal and segmental glomerulosclerosis (40.09%), minimal change disease (23.53%), membranous nephropathy (13.45%), diabetic nephropathy (10.92%), membranous proliferative glomerulonephritis (3.36%), acute glomerulonephritis (3.36%), glomerular thrombotic microangiopathy (2.52%), non-IgA mesengial proliferative glomerulonephritis (1.68%) and amyloidosis (0.84%). Nephrotic syndrome was primary in 57.98% of cases. Secondary etiologies were dominated by diabetes (11.76%), followed by hepatitis B virus (9.24%), lupus, lymphoma, malaria, syphilis, cryoglobulinemia, sickle cell disease and HIV. Conclusion: Future studies should investigate the causes of glomerulopathy secondary to chronic tubulointerstitial lesions.

Measuring small longitudinal phase shifts via weak measurement amplification

Weak measurement amplification,which is considered as a very promising scheme in precision measurement,has been applied to various small physical quantities estimations.Since many physical quantities can be converted into phase signals,it is interesting and important to consider measuring small longitudinal phase shifts by using weak measurement.Here,we propose and experimentally demonstrate a novel weak measurement amplification-based small longitudinal phase estimation,which is suitable for polarization interferometry.We realize one order of magnitude amplification measurement of a small phase signal directly introduced by a liquid crystal variable retarder and show that it is robust to the imperfection of interference.Besides,we analyze the effect of magnification error which is never considered in the previous works,and find the constraint on the magnification.Our results may find important applications in high-precision measurements,e.g.,gravitational wave detection.

Improved spatio-temporal alignment measurement method for hull deformation

In this paper,an improved spatio-temporal alignment measurement method is presented to address the inertial matching measurement of hull deformation under the coexistence of time delay and large misalignment angle.Large misalignment angle and time delay often occur simultaneously and bring great challenges to the accurate measurement of hull deformation in space and time.The proposed method utilizes coarse alignment with large misalignment angle and time delay estimation of inertial measurement unit modeling to establish a brand-new spatiotemporal aligned hull deformation measurement model.In addition,two-step loop control is designed to ensure the accurate description of dynamic deformation angle and static deformation angle by the time-space alignment method of hull deformation.The experiments illustrate that the proposed method can effectively measure the hull deformation angle when time delay and large misalignment angle coexist.

Unknown Environment Measurement Mapping by Unmanned Aerial Vehicle Using Kalman Filter-Based Low-Cost Estimated Parallel 8-Beam LIDAR

The measurement and mapping of objects in the outer environment have traditionally been conducted using ground-based monitoring systems,as well as satellites.More recently,unmanned aerial vehicles have also been employed for this purpose.The accurate detection and mapping of a target such as buildings,trees,and terrains are of utmost importance in various applications of unmanned aerial vehicles(UAVs),including search and rescue operations,object transportation,object detection,inspection tasks,and mapping activities.However,the rapid measurement and mapping of the object are not currently achievable due to factors such as the object’s size,the intricate nature of the sites,and the complexity of mapping algorithms.The present system introduces a costeffective solution for measurement and mapping by utilizing a small unmanned aerial vehicle(UAV)equipped with an 8-beam Light Detection and Ranging(LiDAR)system.This approach offers advantages over traditional methods that rely on expensive cameras and complex algorithm-based approaches.The reflective properties of laser beams have also been investigated.The system provides prompt results in comparison to traditional camerabased surveillance,with minimal latency and the need for complex algorithms.The Kalman estimation method demonstrates improved performance in the presence of noise.The measurement and mapping of external objects have been successfully conducted at varying distances,utilizing different resolutions.

A fast forward computational method for nuclear measurement using volumetric detection constraints

Owing to the complex lithology of unconventional reservoirs,field interpreters usually need to provide a basis for interpretation using logging simulation models.Among the various detection tools that use nuclear sources,the detector response can reflect various types of information of the medium.The Monte Carlo method is one of the primary methods used to obtain nuclear detection responses in complex environments.However,this requires a computational process with extensive random sampling,consumes considerable resources,and does not provide real-time response results.Therefore,a novel fast forward computational method(FFCM)for nuclear measurement that uses volumetric detection constraints to rapidly calculate the detector response in various complex environments is proposed.First,the data library required for the FFCM is built by collecting the detection volume,detector counts,and flux sensitivity functions through a Monte Carlo simulation.Then,based on perturbation theory and the Rytov approximation,a model for the detector response is derived using the flux sensitivity function method and a one-group diffusion model.The environmental perturbation is constrained to optimize the model according to the tool structure and the impact of the formation and borehole within the effective detection volume.Finally,the method is applied to a neutron porosity tool for verification.In various complex simulation environments,the maximum relative error between the calculated porosity results of Monte Carlo and FFCM was 6.80%,with a rootmean-square error of 0.62 p.u.In field well applications,the formation porosity model obtained using FFCM was in good agreement with the model obtained by interpreters,which demonstrates the validity and accuracy of the proposed method.

Quantum block coherence with respect to projective measurements

Quantum coherence serves as a defining characteristic of quantum mechanics,finding extensive applications in quantum computing and quantum communication processing.This study explores quantum block coherence in the context of projective measurements,focusing on the quantification of such coherence.Firstly,we define the correlation function between the two general projective measurements P and Q,and analyze the connection between sets of block incoherent states related to two compatible projective measurements P and Q.Secondly,we discuss the measure of quantum block coherence with respect to projective measurements.Based on a given measure of quantum block coherence,we characterize the existence of maximal block coherent states through projective measurements.This research integrates the compatibility of projective measurements with the framework of quantum block coherence,contributing to the advancement of block coherence measurement theory.

A seismic elastic moduli module for the measurements of low-frequency wave dispersion and attenuation of fluid-saturated rocks under different pressures

Knowledge about the seismic elastic modulus dispersion,and associated attenuation,in fluid-saturated rocks is essential for better interpretation of seismic observations taken as part of hydrocarbon identification and time-lapse seismic surveillance of both conventional and unconventional reservoir and overburden performances.A Seismic Elastic Moduli Module has been developed,based on the forced-oscillations method,to experimentally investigate the frequency dependence of Young's modulus and Poisson's ratio,as well as the inferred attenuation,of cylindrical samples under different confining pressure conditions.Calibration with three standard samples showed that the measured elastic moduli were consistent with the published data,indicating that the new apparatus can operate reliably over a wide frequency range of f∈[1-2000,10^(6)]Hz.The Young's modulus and Poisson's ratio of the shale and the tight sandstone samples were measured under axial stress oscillations to assess the frequency-and pressure-dependent effects.Under dry condition,both samples appear to be nearly frequency independent,with weak pressure dependence for the shale and significant pressure dependence for the sandstone.In particular,it was found that the tight sandstone with complex pore microstructure exhibited apparent dispersion and attenuation under brine or glycerin saturation conditions,the levels of which were strongly influenced by the increased effective pressure.In addition,the measured Young's moduli results were compared with the theoretical predictions from a scaled poroelastic model with a reasonably good agreement,revealing that the combined fluid flow mechanisms at both mesoscopic and microscopic scales possibly responsible for the measured dispersion.

Fast compressed sensing spectral measurement with adaptive gradient multiscale resolution

We propose a fast,adaptive multiscale resolution spectral measurement method based on compressed sensing.The method can apply variable measurement resolution over the entire spectral range to reduce the measurement time by over 75%compared to a global high-resolution measurement.Mimicking the characteristics of the human retina system,the resolution distribution follows the principle of gradually decreasing.The system allows the spectral peaks of interest to be captured dynamically or to be specified a priori by a user.The system was tested by measuring single and dual spectral peaks,and the results of spectral peaks are consistent with those of global high-resolution measurements.

Finesse measurement for high-power optical enhancement cavity

Finesse is a critical parameter for describing the characteristics of an optical enhancement cavity(OEC). This paper first presents a review of finesse measurement techniques, including a comparative analysis of the advantages, disadvantages, and potential limitations of several main methods from both theoretical and practical perspectives. A variant of the existing method called the free spectral range(FSR) modulation method is proposed and compared with three other finesse measurement methods, i.e., the fast-switching cavity ring-down(CRD) method, the rapidly swept-frequency(SF) CRD method, and the ringing effect method. A high-power OEC platform with a high finesse of approximately 16000 is built and measured with the four methods. The performance of these methods is compared, and the results show that the FSR modulation method and the fast-switching CRD method are more suitable and accurate than the other two methods for high-finesse OEC measurements. The CRD method and the ringing effect method can be implemented in open loop using simple equipment and are easy to perform. Additionally, recommendations for selecting finesse measurement methods under different conditions are proposed, which benefit the development of OEC and its applications.